Dynex DX-TVM102 User Manual

Important safety instructions

[Latched]

The DX-TVM102 TV mount is designed to support a Flat Panel TV weighing up to 50 lbs. (22.7 kg).

Caution

The DX-TVM102 is designed for use in wood frame walls only! The weight of your TV must not exceed 50 lbs. (22.7 kg). The wall must be capable of supporting ﬁve times the weight of the TV and wall mount combined.

Do not use this product for any purpose not explicitly speciﬁed by Dynex. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualiﬁed contractor. Dynex is not responsible for damage or injury caused by incorrect installation or use.

Warning

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.

Supplied parts and hardware

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer, but contact Customer Service. Never use damaged parts.

PARTS LIST

Attach the TV bracket

Step 2a: TVs with ﬂat back panels.

Mount the TV to the wall bracket

First mount the top hooks of the TV brackets onto the wall bracket, then press the bottom of the TV brackets against the wall bracket until they snap into place.

HEAVY! You will need

assistance with this step.

Note: Not all parts will be used Missing parts? Call 800-573-2860

A Wall bracket (1) B Left TV bracket (1) C Right TV bracket (1) D M4 × 0.47" (12 mm) screws (4) E M5 × 0.47" (12 mm) screws (4) F M6 × 0.47" (12 mm) screws (4) G M6 × 0.79" (20 mm) screws (4) H M4 × 1.18" (30 mm) screws (4) I M5 × 1.18" (30 mm) screws (4) J M6 × 1.38" (35 mm) screws (4) K M4/M5 washer (8) L M6 washer (4) M M4/M5 spacer (4) N M6 spacer (4) O 5/16" (7.9 mm) washer (2) P Tilt bracket (2) Q 5/16" × 2.5" (63.5 mm) lag bolt (2) R Carriage bolt (4) S Nylock nut (4)

M4 x 30mm

M5 x 30mm

M6 x 35mm

M4 x 12mm

M5 x 12mm

M6 x 12mm

M6 x 20mm

Step 2b: TVs with rounded or angular back panels. Optional: Use washer [K] with M4 or M5 hardware only.

Maintenance

To remove the TV from the wall bracket, pull down on the release straps, pull the bottom of the TV away from the wall bracket, then lift the TV completely oﬀ the wall bracket.

Adjust the release straps length

Adjust the release straps so they are level with bottom of the TV; this allows the straps to be accessible, yet concealed, when the TV is on the wall.

M4 / M5 M6

Tools you will need:

• Power drill

• 3/16" wood drill bit

• Phillips screwdriver

• Level

• Socket wrench with 1/2 in. socket

• Pencil

• Stud ﬁnder

• Adjustable wrench

• Awl

3/16 in.

1/2 in.

5/16 x 2.5 in.

M4 / M5

5/16 in.

[Unlatched]

Attach the wall bracket to the wall studs.

Caution: Avoid potential injuries or property damage! Any material covering the wall must not exceed 16 mm (5/8 in.).

Caution: Avoid potential injury or property damage! Do not overtighten the lag bolts [Q]. Tighten the lag bolts [Q] only until the washers [O] are pulled ﬁrmly against the wall bracket [A].

< 16 mm

(5/8 in.)

63.5 mm (2.5 in.)

DX-TVM102 Slim-Proﬁle TV Mount

Set the viewing angle (optional)

Attach the tilt brackets.

5°

6907-002001 <00>

3/16 in. 5 mm

© 2009 Best Buy Enterprise Services, Inc. All rights reserved. DYNEX is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

USER GUIDE

ENGLISH 09-0602