ASSEMBLY GUIDE
DX-DTVMFP23
TV Wall Mount
For either wood-stud or
concrete wall installations
Before using your new product, please read these instructions to prevent any damage.
Safety information and specifications . . .2
Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . .3
Package contents . . . . . . . . . . . . . . . . . . . . . .3
Installation instructions. . . . . . . . . . . . . . . . .5
2
Maximum TV weight: 120 lbs. (55 kg)
TV screen size: 37 in. to 70 in. diagonal
Wall Mount dimensions (H × W × D):
27.2 × 16.9 × 0.9 in. (692 × 430 × 22 mm)
Wall-mount weight: 3.59 lbs. (1.63 kg)
We’re here for you
www.dynexproducts.com
For customer service, call:
1-800-305-2204 (U.S. and Canada) or 01-800-926-3020
(Mexico)
27.2 in. (692 mm)
23.6 in. (600 mm)
16.9 in.
(430 mm)
6.1 in.
(154 mm)
Safety information and specifications
IMPORTANT
SAFETY
INSTRUCTIONS SAVE THESE
INSTRUCTIONS
CAUTION: Do not use this
product for any purpose not
explicitly specified by Dynex.
Improper installation may
cause property damage or
personal injury. If you do not
understand these directions, or
have doubts about the safety of
the installation, contact
Customer Service or call a
qualified contractor. Dynex is
not responsible for damage or injury caused by incorrect installation or use.
The weight of your TV must not exceed 120 lbs. (55 kg). The wall must be capable of supporting five times
the weight of your TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
DX-DTVMFP23
Edge-to-edge
stud finder
Pencil
Magnetic Removable Level
Phillips screwdriver
Socket wrench with 1/2"
(13 mm) socket or
adjustable wrench
Measuring tape
Drill
3/16" (5 mm) wood drill bit for
wood stud wall
OR
3/8" (10 mm) masonry drill bit
(concrete only)
Hammer
A
B
C
D
Tools needed
3
ardware
Package contents
You will need the following tools to assemble your new TV wall mount:
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
A Wall Plate (1) C Right TV Bracket (1)
B Left TV Bracket (1) D Plastic covers (2)
4
Label Hardware Qty.
E4
F4
G
8
H4
I4
J4
K4
L4
M4 × 12 mm
screw
M4 × 35 mm
screw
M4 washer
M6/M8 washer
Universal spacers
M6 × 12 mm
screw
M6 × 35 mm
screw
M8 × 16 mm
screw
Label Hardware Qty.
M4
N4
O4
P4
Q4
1
M8 × 20 mm screw
M8 × 36 mm screw
Lag bolt washer
5/16" × 2 3/4" lag bolt
Concrete anchor
Magnetic
removable
level
10 20 30 40 50 60 70 80 90 1 00mm
1234in
TV Hardware Bag
DX-DTVMFP23
Installation instructions
STEP 1- Determine whether your TV has a flat back or an
irregular or obstructed back
1
Carefully place your TV face-down on a cushioned, clean surface to protect the screen.
2
If your TV has a ta ble-top stand attached, remove the stand. See the documentation that came with your
TV for instructions.
3
Temporarily lay the TV brackets (B and C) on the back of your TV.
4
Align the screw holes in the TV brackets with the mounting screw holes on your TV.
5
Identify which type of back your TV may have:
• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need
spacers when assembling the wall mount.
• Obstructed back: The brackets block one or more of the jacks on the back of your TV. You will need
spacers when assembling the wall mount.
5
• Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You
will need spacers when assembling the wall mount.
6
Remove the TV brackets.
6
Screw is too
long
Screw fits
correctly
Screw is too
short
STEP 2 - Select screws, washers, and spacers
1
Select the hardware for your TV (screws, washers, and spacers). Some TVs come with mounting
hardware included (usually in the holes on the back of the TV.) If you don't know the correct length of
the mounting screws your TV requires, test various sizes by hand threading the screws.
a. Select one of the following types of screws:
Flat back Obstructed back
M4 × 12 mm screws (E) M4 × 35 mm screws (F)
M6 × 12 mm screws (J) M6 × 35 mm screws (K)
M8 × 16 mm screws (L) M8 × 36 mm screws (N)
M8 × 20 mm screws (M)
b. Select from the following washers:
M4 washer (G)M6/M8 washer(H)
c. For an irregular or obstructed TV back, use the universal spacers (I).
CAUTION:
adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and
contact customer service. Use the shortest screw and spacer combination to accommodate your TV.
Using hardware that is too long may damage your TV. However, using a screw that is too short may
cause your TV to fall from the mount.
2
Remove the screws.
To avoid potential personal injuries and property damage, make sure that there are
DX-DTVMFP23
D - Plastic cover
A - Wall plate
D - Plastic covers (2)
A - Wall plate
STEP 3 - Attaching the plastic covers to the wall plate
1
Fit the plastic covers (D) over the ends of the wall plate (A).
2
For a flat back TV, go to “STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on
page 8.
-ORFor an irregular or obstructed back, go to “STEP 4 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs” on page 9.
7
You ’ l l ne ed
8
or
or
G (4)
E (4)
Phillips screwdriver
B and C TV brackets
or
or
J (4)
H (4)
or
L (4)
Level
or
M (4)
STEP 4 - Option 1: Attaching the mounting hardware to TVs
with a flat back
Note: If you plan to use a 5° tilt with a larger TV (42”+), we suggest using spacers with the mounting
brackets so that the bottom of the TV does not touch the wall.
1
Align the left and right TV brackets (B and C) with the screw holes on the back of the TV. Make sure that
the brackets are level.
2
Install washers (G or H), and screws (E, J, L, or M) into the holes in the back of the TV.
3
Tighten the screws until they are snug against the TV brackets. Do not over tighten.
You’l l ne ed
DX-DTVMFP23
or
or
If you are using M4 (G)
washers (only), place
them both in front of
and behind the
brackets.
G (8)
F (4)
Phillips screwdriver
I (4)
B and C TV
brackets
H (4)
or
or
K (4)
N (4)
or
STEP 4 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs
1
Place spacers (I) over the screw holes on the back of the TV.
1
Align the left and right TV brackets (B and C) with the screw holes on the back of the TV. Make sure that
the brackets are level.
2
If you are using M4 washers (G), place them between the spacers and TV brackets and over the holes in
the TV brackets. If you are using M6/M8 washers (H), place them over the holes in the TV brackets. Insert
screws (F, K , or N) through the washers, TV brackets, and spacers.
3
Tighten the screws until they are snug against the TV brackets. Do not over tighten.
9
You’ll need
10
A
B
a
b
Measuring tape
Pencil
STEP 5 - Determine wall-mount location
Notes:
• For more detailed information on determining where to drill your holes, visit our online height-finder
at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder
• Your TV should be high enough so your eyes are level with the middle of the screen. Normally, this is
40 to 60 inches from the ground.
The center of your TV will match the center of the wall plate (A). Before you drill holes in the wall:
1
Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is
measurement a.
2
Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall.
Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment
centers or TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray
player or cable box). This measurement is b.
3
Add a + b. The total measurement is the height where you want the center of the wall plate to be on the
wall.
4
Use a pencil to mark this spot on the wall.
You’ll need
DX-DTVMFP23
- Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 11/2 x 31/2 in. (38 x 89 mm).
- Minimum spacing between horizontal fasteners cannot be less than 16 in. (40 cm)
3/16 in. (5 mm)
Level
2 in. (50 mm)
Wood stud
Edge-to edge
stud finder
P (4)
Pencil
Drill
3/16" wood drill bit
1/2" socket wrench
Level
O (4)
Wall plate (A)
STEP 6 - Option 1: Installing on a wood stud wall
Note: Any drywall covering the wall must not exceed 5/8" (16 mm).
1
Locate the studs. Verify the centers of the studs with an edge-to-edge stud finder.
2
Align the wall plate (A) at the height you determined in the previous step, make sure that it is level, then
use a pencil to mark the lag bolt hole locations (4) on the stud centers. Remove the wall plate (A).
3
Drill pilot holes to a depth of 2 in. (50 mm) using a 3/16 in. (5 mm) diameter drill bit.
4
Align the wall plate (A) with the pilot holes, insert the lag bolts (P) through the lag bolt washers (O),
then through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall
plate.
CAUTION
: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (P).
11
You’ll need
12
STEP 6 - Option 2: Installing on a solid concrete or concrete
block wall
CAUTION:
Mount the wall plate directly onto the concrete surface.
1
Align the wall plate (A) at the height you determined in the previous step, make sure th at it is level, then
use a pencil to mark the lag bolt hole locations (4). Remove the wall plate (A).
2
Drill pilot holes to a depth of 2.36 in. (60 mm) using a 3/8 in. (10 mm) diameter masonry drill bit.
3
Insert the concrete wall anchors (Q) into the pilot holes and use a hammer to make sure the anchors are
flush with the concrete surface.
4
Align the wall plate (A) with the anchors, insert the lag bolts (P) through the lag bolt washers (O), then
through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall plate.
CAUTION:
To prevent property damage or personal injury, never drill into mortar between blocks.
Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (P).
DX-DTVMFP23
2.36 in. (60 mm)
* Minimum solid concrete thickness: 8 in. (203mm).
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm).
The minimum distance between the top two fasteners cannot be less than 16 in. (40 cm)
Concrete wall
Level
3/8 in. (10 mm)
P (4)
Penc il
Drill
1/2" socket wrench
Level
O (4)
Wall plate (A)
3/8" masonry drill bit
Q (4)
.
13
You’ll need
14
HEAVY! You will need assistance
with this step.
Wall
Wall
The pendents have a
magnetic button on the
end so that you can stick
them to the brackets to
keep them out of sight.
Press the brackets after you
mount the TV to the wall plate
to lock the assembly to the wall
plate.
The brackets must
engage the slotted
flanges of the wall plate
to hold your TV in place.
The spring
self-locking system
engages the wall
plate when you press
on the brackets after
mounting your TV.
This prevents your
TV from jarring
loose.
STEP 7 - Mounting the TV to the wall plate
1
Place the TV brackets (B and C) into the slotted flanges of the wall plate (A).
2
Push the bottom of the TV toward the wall until the spring self-locking system clicks into place.
Congratulations, you have finished the installation. Time to watch some TV!
DX-DTVMFP23
Pull down to unlatch.
HEAVY! You will need assistance
with this step.
If you ever need to remove the TV from the wall plate
1
Grasp the TV by the bottom edge, then pull down on the locking cords and pull the bottom of the TV out
from the wall.
2
Release the locking cords and lift the top of the TV from the wall bracket.
15
www.dynexproducts.com
1-800-305-2204 (U.S. and Canada) or 01-800-926-3020 (Mexico)
DYNEX is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2014 Best Buy. All rights reserved.
Made in China.
V1 ENGLISH 14-1054
Loading...