Duke TM-SC User Manual

SUGGESTED SPECIFICATIONS FOR CONVEYOR

MODEL TM-SC

Tray Make-up Conveyor to be
model TMSC, UL and ETL Listed, and NSF approved commercial kitchen conveyor.

Conveyor Belt to be stainless steel roller type chain with removable, low friction acetal slats, 10"
wide. Slats are individually removable from #60 stainless steel chain without the use of tools. Belt to
operate at a variable speed of 5 to 40 feet per minute.

Conveyor Bed to be constructed on #14-gauge, 300 series stainless steel with 1-1/2” high x 2” wide
channel edge on both sides and ends turned down square. Sides formed integral to top. Polish stainless
steel to a #3 finish.

Drive Housing to be a welded stainless steel frame with removable 16-gauge stainless steel access
door. Stainless steel scrap pan located beneath drive housing for easy removal. Drive housing to be
supported by four 1-5/8" O.D., 16-gauge stainless steel legs and stainless steel adjustable bullet feet.

Drive Type to be 90-volt DC, ½ H.P. variable speed with 120volt, 60-cycle service, internal torque
limit adjustment and ramp acceleration start. Controlled by one (1) on/off switch station and variable
speed control.

Drive end of conveyor furnished with one bed mounted Limit Switch to control the flow of trays.
Concealed anti-jam silver saver switch plate provided also at drive end of belt to prevent foreign
material from jamming drive system.

SOUTHERN ENGINEERING SYSTEMS by Duke Mfg Co.,

Conveyor supported by 1-5/8” 16-gauge stainless steel tubing Legs with welded stainless steel cross
rails. Leg frames fitted into enclosed, round stainless steel gussets welded to stainless steel channel
braces and fitted with stainless steel adjustable bullet feet.

Optional UL Listed Electrical Raceway constructed of 16-gauge, 300 series stainless steel with #3
finish. Raceway furnished with removable top cover and fitted with properly sized receptacles and
stainless steel face plates, pre-wired to a panel box at the end of the conveyor. Panel box to be housed
in stainless steel enclosure fitted with hinged, locking, 18-gauge stainless steel door.

Conveyor to be pre-wired and factory tested.

Conveyor to carry UL and ETL listing and shall be NSF approved. E

quipment built in an ISO

9001:2000 approved manufacturing facility.

2305 N. Broadway
St. Louis, MO 63012
Ph 314-231-1130
Fax [phone]

www.dukemfg.com

5/07

BY

"Your Solutions Partner"

Optional Accessories

 12” Slat-Chain Belt  Prison Security Package
 10” Slat-Pin Belt @ 24” Radius Model (TM-SR)  S/S Belt Cover W/Hanger Brackets
 Stainless Raceway & Panel Box  Movable Over Shelf _____Dbl.
 Mobile Package (Note: Max 100Amp Main  Stationary Over Shelf _____Dbl
Cord & Plug with Optional Raceway)  Stationary Under Shelf
 Flanged Feet  Removable Under Shelf
 Additional Start-Stop Station  3” High x 1-1/4” Rolled Rim Sides
 Foot Switch (Momentary Stop)  7/8” High x 1-1/4” Marine Edge Sides
 Cord & Plug (Without Raceway  Other _____________________________
 Auto-wash System _____________________________
 Flush-Wash (Drip pan and Drains only.)

COMMENTS/NOTES ____________________________________________________________

SHOWN WITH OPTIONAL S.S. RACEWAY & S.S.

PANELBOX. RACEWAY FITTED WITH OPTIONAL

22 1/2"

2"

1 1/2"

8"

3'-0"

10"

SECTION VIEW

10"

BELT

2"

1 5/8" O.D. 16 GA. S.S. TUBING LEGS
WITH 16GA SS CROSS RAILS

ACCESS COVER TO

ELECTRIC WIRING

RECEPTACLES

START STOP STATION

RECESSED INTO END

PANEL.

22 1/2"

10"

BELT

END ELEVATION

18 GA. S.S. ACCESS DOOR TO ENCLOSE
ELECTRIC PANEL BOX. DOOR MOUNTED
ON FULL HEIGHT PIANO HINGE AND
FITTED WITH RECESSED HANDLE,
KEY LOCK

NOTE: CASTERS NOT AVAILABLE WHEN PANEL BOX INCOMING

SERVICE EXCEEDS 100AMPS.