Duke TM-CC User Manual

SUGGESTED SPECIFICATIONS FOR CONVEYOR

MODEL TM-CC

Carrousel Tray Make-up Conveyor to be

SOUTHERN ENGINEERING SYSTEMS by Duke Mfg

Co., model TMCC, UL and ETL Listed, and NSF approved commercial kitchen conveyor.

Conveyor Belt to be stainless steel roller type chain with removable, low friction acetal slats, 10" wide.
Slats are individually removable from #60 stainless steel chain without the use of tools. Belt to operate at a
variable speed of 5 to 40 feet per minute.

Conveyor Bed to be constructed on 14-gauge, 300 series stainless steel with bull nose rolled edge along all
sides. Polish stainless steel to a #3 finish.

Drive Housing to be a welded stainless steel frame with removable 16-gauge stainless steel access door.
Drive housing to be supported by four 1-5/8" O.D., 16-gauge stainless steel legs and stainless steel
adjustable bullet feet. Note: applications less than 7’0” wide require the drive housing be mounted along the
side of the conveyor.

Drive Type to be 90-volt DC, ½ H.P. variable speed with 120 volt-60 cycle service, internal torque limit
adjustment and ramp acceleration start. Controlled by one (1) on/off switch station and variable speed
control.

(Optional) Bed mounted Limit Switch furnished at drive end of conveyor to control the flow of trays.

Conveyor supported by 1-5/8” 16-gauge stainless steel tubing Legs with welded stainless steel cross rails.
Leg frames fitted into enclosed, round stainless steel gussets welded to stainless steel channel braces and
fitted with stainless steel adjustable bullet feet.

(Optional) UL Listed Electrical Raceway constructed of 16-gauge, 300 series stainless steel with #3 finish.
Dual Raceways furnished with removable top covers and fitted with properly sized receptacles and stainless
steel faceplates, pre-wired to a panel box at the end of the conveyor. Panel box to be housed in stainless steel
enclosure fitted with hinged, locking, 18 gauge stainless steel door.

Conveyor to be pre-wired and factory tested.

Conveyor to carry UL and ETL listing and shall be NSF approved. All equipment built in an ISO
9001:2000 approved manufacturing facility.

2305 N. Broadway

St. Louis, MO 63012
Ph 314-231-1130
Fax [phone]

www.dukemfg.com

BY

"Your Solut ions Par tner"

5/07

Optional Accessories

 12” Slat-Chain Belt  Prison Security Package (W/SR Belt)

 Stainless Raceway & Panel Box  Dual Service - Sloped Over Shelf
 Mobile Package (Note: Max 100Amp Main  Dual Service - Sloped Lower Shelf
Cord & Plug with Optional Raceway)  Stationary Under Shelf
 Flanged Feet  7/8” High x 1-1/4” Marine Edge
 Additional Start-Stop Station  Hot Food Wells _____Qty
 Limit Switch (Bed Mount)  Mechanical Cold Pan
 Foot Switch (Momentary Stop)  Ice Cold Pan
 Hip Switch (Constant Stop)  Other ____________________________
 Cord & Plug (Without Raceway) _____________________________
 Hinged – Removable Drive Access Door

COMMENTS/NOTES ____________________________________________________________

14GA SS OVERHEAD SHELF

(OPTIONAL)

14GA SS LOWER SHELF

(OPTIONAL)

REMOVABLE SS PANEL

DRIVE END VIEW

SS GUSSET BRACKETS

PANEL BOX & RACEWAYS

START / STOP STATION

W/ SPEED CONTROL

SHOWN WITH OPTIONAL S.S. RACEWAY & S.S.

PANELBOX. RACEWAY FITTED WITH OPTIONAL

16GA SS TUBING

(OPTIONAL)

1-5/8" 16GA SS LEGS

W/ADJ SS BULLET FEET

RECEPTACLES

7'0" TYPICAL

(6'-0" MIN)

3'- 1/2"

10"

BELT

PANEL BOX END VIEW

4'-6"

2'-10"

DBL WALL SS DOOR ON FULL HEIGHT

PIANO HINGE, W/RECESSED

HANDLE & KEY LOCK