Dual XDM6820 User Manual

INSTALLATION/OWNERS MANUAL

AM/FM/CD/MP3/WMA Receiver with Detach Face

XDM6820

XDM6820 INSTALLATION

Preparation

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove 2 transit screws located on top of the unit.

• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.

• Install mounting sleeve into opening, bending tabs to secure.

• Connect wiring harness and antenna. (consult a qualified technician if you are unsure)

• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).

• Test for correct operation and slide into mounting sleeve to secure.

• Snap trim ring into place.

• Mount the iplug™ adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8” Phillips head screws.

XDM6820 INSTALLATION

Wiring Diagram

FUSE

When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDM6820 uses one 10 amp ATM fuse located beside the wiring connector.

XDM6820 OPERATION

Control Locations

Release

Power

Volume

Band/Play/Pause

Mode/Search

Auto Store/Preset Scan/Enter

Tune/Track Down

Eject

Tune/Track Up

Display/0

EQ/9

Tuner Scan/8

Local/Distance/7

Preset 6/Folder Up

Preset 5/Folder Down

Preset 4

Preset 3/Intro

Preset 2/Random

Preset 1/Repeat

Audio

Loudness

Mute

2122 20 19 18 17 16 15 14 13 12 11

1 2

4 5

8 9 10

The XDM6820 allows playback of your favorite MP3 and WMA files recorded on CD-R and CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track search - even while a song is currently playing!

XDM6820 OPERATION

General Operation

Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.

Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate.

Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off.

Press MODE to select between tuner, CD player and auxiliary input. Modes of operation are indicated in the display.

Press LOUD to activate and deactivate the loudness contour curve. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes.

Adjust volume using rotary encoder (00-46).

Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display.

Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected).

Press DISP to select between clock and radio frequency (tuner mode), clock and CD track/elapsed time (CD mode), or clock and AUX (AUX mode).

With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE

to adjust the hours

and TUNE

to adjust the minutes. Press DISP

momentarily to save the selected time.

The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).

Faceplate Removal

Semi-permanent

Faceplate Installation

Power On/Off

Mode

Loudness

Volume

Programmable

Turn-On Volume

Preset EQ Curves

Display

Set the Clock

12/24-hour Clock

XDM6820 OPERATION

General Operation

In tuner mode, press and hold DISP then press TUNE

to select function priority display. "FREQ" will momentarily appear in the display.

Note: "FUNC" will appear in CD or AUX modes. Radio frequency (tuner mode), CD track/elapsed time (CD mode) or AUX (AUX mode) will be displayed by default.

Note: When playing MP3/WMA files, the track number/elapsed time, track name, directory name, title, artist, album, year or comment will be displayed by default. Clock is accessed by pressing DISP momentarily.

Press and hold DISP then press TUNE

to select time display priority. "TIME" will momentarily appear in the display. Clock will be displayed by default. Radio frequency, CD track/elapsed time or MP3/WMA file information is accessed by pressing DISP momentarily.

Programs unit to display clock/no clock when unit is off. Press and hold MODE then press PRESET 1 to select clock priority on/off. "CLK ON" or "CLK OFF" will momentarily appear in the display.

Press and hold for more than 2 seconds to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate.

Press and hold AUDIO for 3 seconds to turn confirmation beep on/off.

Press MUTE to silence the audio. "MUTE" will flash in the display. Press MUTE again to cancel.

Programmable Display

Priority

Programmable Clock

Priority

Reset

Confirmation Beep

Mute

+ 14 hidden pages