Dual XDM6351 User Manual

XDM6351

INSTALLATION/OWNER'S MANUAL

AM/FM/CD Receiver with Detachable Face

XDM6351 INSTALLATION

Preparation

Please read entire manual before installation.

Before You Start

•Disconnect negative battery terminal. Consult a qualified technician for instructions.

•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

•Remove trim ring from unit.

•Remove 2 transit screws located on top of the unit.

•Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.

•Install mounting sleeve into opening, bending tabs to secure.

•Connect wiring harness and antenna. Consult a qualified technician if you are unsure.

•Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).

•Test for correct operation and slide into mounting sleeve to secure.

•Snap trim ring into place.

REMOVAL KEYS

MOUNTING SLEEVE

XDM6351 HEAD UNIT

INSTALLATION

MOUNTING KIT

OR DASHBOARD

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

2

XDM6351 INSTALLATION

Wiring Diagram

Rear RCA Preamp Output

Connect to an amplifier input

Antenna

Connector

10 AMP	FUSE
AGC Fuse
	When replacing the fuse,
	make sure new fuse is the
	correct type and amperage.
	Using an incorrect fuse could
	damage the radio.
	The XDM6351 uses one
	10 amp AGC fuse located
	in-line.

3

XDM6351 OPERATION

Control Locations - Receiver

1

2

3

4

5

6

7

8

9

23

22

21

20

19

18

17

16

15

14

13

12

11

10

1	Release	13	Preset 4 / Random
2	Mute	14	Preset 3 / Repeat
3	AMS	15	Preset 2 / Intro
4	Scan	16 Preset 1 / Play / Pause
5	Display	17	Local / Distance
6	Audio / Volume	18	Mono / Stereo
7	Loudness	19	Tune / Track Up
8	Eject	20	Band
9	USB Input	21	Mode
10	Auxiliary Input	22	Power
11	Preset 6 / +10 Skip	23	Tune / Track Down
12	Preset 5 / -10 Skip

4

XDM6351 OPERATION

Control Locations - Remote

12

18

17

16

15

14

13

12

MODE BAND SCAN DISP

LOUD

-10 +10 MUTE

XDM6351

3

4

5

6

7

8

9

10

11

1	Power	10	Mute
2	Volume Up	11	Preset 6 / +10
3	Select	12	Preset 5 / -10
4 Tune / Track Up		13 Preset 4 / Random
5	Volume Down	14 Preset 2 / Intro
6	Scan	15 Preset 1 / Play / Pause
7	Display	16	Mode
8	Loudness	17	Band
9	Preset 3 / Repeat	18	Tune / Track Down

5

XDM6351 OPERATION

General Operation

Faceplate Removal

Power On/Off

Mode

Auxiliary Input

Volume

Display

Reset

Set the Clock

12/24-hour Clock

Setup Menu

Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure.

Press or any other button (except EJECT) to turn the unit on. Press to turn the unit off.

Press MODE to select between AM/FM, CD player, auxiliary, USB and SD card. Modes of operation are shown in the display.

NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.

The XDM6351 offers a 3.5 mm auxiliary input port on the front panel of the unit for connecting an audio device, MP3 player, etc. Press MODE to select auxiliary input mode.

Adjust volume using volume knob (00-47).

Press DISP to show the clock. During playback of MP3/WMA files, ID3 tag information, elapsed time, track number and file/folder names will automatically rotate on the display.

Press RESET upon initial installation or if abnormal operation occurs. Reset button is located behind the front panel.

With the unit on, press and hold DISP until the clock begins to flash, then release. Turn the volume knob to the right to adjust the hours or to the left to adjust the minutes.

The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).

Press and hold AUDIO for more than 3 seconds to access the setup menu. Press AUDIO momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.

6

			XDM6351 OPERATION
		General Operation - Setup Menu
	Menu Function	Options	Action
	Equalizer	DSP	Toggles between the following equalization options: OFF,
			POP, ROCK, CLASS and FLAT).
	Beep	BEEP OFF	Disables the confirmation beep.
	Confirmation	BEEP ON	Enables the confirmation beep.
	Seek Priority	SEEK 1	Enables seek tuning priority.
		SEEK 2	Enables manual tuning priority.
		VOL LAST	Programs unit to always turn on at the last volume selected
	Programmable		before it was turned off.
	Turn On Volume	VOL ADJ	Programs unit to always turn on at a specific volume. Any
			volume level 1-47 can be selected.
	Tuner	FREQ USA	Programs the unit to USA tuner spacing.
			(200kHz for FM and 10kHz for AM).
	Frequency
			Programs the unit to European tuner spacing.
	Spacing	FREQ EUR
			(50kHz for FM and 9kHz for AM).

7

XDM6351 OPERATION

General Operation

Audio Press AUDIO momentarily to select between Bass, Treble, Balance and Fader.

BASS TREBLE BALANCE FADER

Bass Press AUDIO until BAS appears then rotate volume knob left/right to adjust ( -7 minimum / +7 maximum).

Treble Press AUDIO until TRE appears then rotate volume knob left/right to adjust ( -7 minimum / +7 maximum).

Balance Press AUDIO until BAL appears then rotate volume knob left/right to adjust (BAL 10L - BAL 10R).

BAL EVEN represents equal balance

Fader Press AUDIO until FAD appears then rotate volume knob left/right to adjust (FAD 10R - FAD 10F).

FAD EVEN represents equal fader

8