DSC PC5200 Instalation Instructions
S
PC5200 v2.0 Installation Instructions
Power Supply Module
The PC5200 can be used to provide up to 1.0A of additional current to the
compatible DSC Alarm Controllers, models PC5010, PC5015, PC5020,
PC1864, PC1832 and PC1616. PC1616/1832/1864 v4.1 or higher supports up to four PC5200 modules.
This installation sheet shall be used with the Installation Manual of the DSC
equipment to which the PC5200 is connected or powered from (e.g. alarm
controller, power supply, etc.).
General
This product meets the requirements of Class II, Grade 2 equipment as per
EN50131-1:2006+A1:2009, EN50131-3:2009 Type B, EN50131-6:2008
Type A.
Specifications
•Power Supply Type A as per EN50131-6 Standard
•Temperature range: -10ºC to +55ºC
•Relative Humidity: 93% non condensing
•Input ratings: 220V-240Vac, 50/60Hz, 200mA
•Transformer required, mounted in the same enclosure and permanently
connected
NOTE: For installations using the transformer mounted inside the cabinet,
replace the fuse only with same type (20mm) rated 250V/315mA.
•Transformer secondary ratings: 16.5Vac, 40VA
•Board current draw: 20mA (set and unset state / alarm and non-alarm
state)
•Board dimensions: 145 mm x 83 mm
•AUX output ratings: 12V
85% to110% of rated value and output current is between 0.0A - 1.0A
max.
•Resettable fuse (PTC) used on circuit board instead of replaceable fuses
•Output ripple voltage: 600mVp-p max
•No Overvoltage protection devices required on the outputs
•Storage device: rechargeable battery, rated 12V
3-5 years
•Battery capacity: 4Ah, 7Ah or 14Ah (2 x 7Ah) max.
•Maximum standby time 24h (when using 14Ah battery capacity and AUX
current limited to 480mA max. Refer to Table 1
•Recharging time: up to 80% in less than 72h
•Low battery trouble indication threshold 11.5V
•Battery deep discharge protection (cut-off at 9.5VDC)
NOTE: Main control panel and power supply shall be powered from the
same AC mains circuit. Deep discharge protection works only when there is
no voltage on the keybus connection.
NOTE: For EN50131-6:2008 compliant installations, use only one 12V/7Ah
battery for 12h of required standby time (550mA output current).
•Supervision for loss of primary power source (AC Fail) battery fail or battery low voltage (Battery Trouble) with indication provided on the keypad
DC, -15%/+15% when Input voltage is between
DC. Replace battery every
DC
Table 1
UL Residential UL Commercial EN50131
PC5200 Current
Draw 20mA
Max. Aux Current
Draw @12V
Transformer
Requirements
Battery
Requirements
UL Listed
Enclosures
Standby Time (min.) 4 hours 24 hours 4 hours 12 hours
Burglary Fire Burglary Grade 2 /Class 2
1A 550mA 1A 550mA
DC
16V,
40VA
7Ah min
PC500C
16V, 40VA 16V, 40VA
14Ah min
(2x7Ah)
PC5003C
(Household Fire
& Burglary)
7Ah min 7Ah min
CMC-1
PC4050CAR
16.5V, 40VA
(Mounted inside
cabinet)
PC5003C
PUC1
Terminal Descriptions
NOTE: Devices that require
power from the PC5200 shall be
UL Listed for the intended
application and operate over the
range 11.5 - 12.5VDC.
Residential Fire Applications
For battery requirements and
standby time refer to Table 1.
Recommended Battery:
DSC model BD7-12.
AC - Supervised, the PC5200 requires a 16V/40VA transformer. Connect the
primary of the transformer to an unswitched AC source (maximum current
draw is 0.5A) and connect the secondary of the transformer (US market
only) to these terminals.
AUX+ - This terminal is used to provide power for devices & modules.
Please refer to Table 1 for maximum ratings.
Connect the positive lead of powered devices to AUX and the negative to the
proper output terminal (O1 to O4).
TAM - This can be used to tamper the cabinet in which the PC5200 is
mounted. Connect a normally closed (NC) switch across TAM and BLK. If
the tamper is not being used connect a piece of wire across TAM and BLK to
remove the trouble condition.
Keybus- The 4-wire Keybus connection is used by the panel to communicate with the module. Connect the RED, BLK, YEL & GRN terminals to the
RED, BLK, YEL & GRN Keybus terminals on the compatible control panel.
Residential
Burglary
120VAC 60Hz
PRIMARY
Class 2
TRANSFORMER
16VAC / 40VA PTD 1640
AUX**
TO
KEYBU
RED
BLK
YEL
GRN
BLK
Enclosures
The PC5200 can be installed in the metal enclosures listed below:
•Model PC5003C (removable door) made of 22Ga steel, painted, dimensions: 248mm(L) x 298mm(W) x 76mm(H), weight: 1500g.
•Model PC5003C (hinged door) made of 1.2mm thick steel, painted,
dimensions: 248mm(L) x 298mm(W) x 76mm(H), weight: 2500g
•Model Power UC1 made of 18Ga steel, painted, dimensions: 315mm(L) x
319mm(W) x 100mm(H), weight: 3150g.
•Model PC4003C made of 18Ga steel, painted, dimensions: 230mm(L) x
180mm(W) x 75mm(D), weight 1050g.
Tamper protection switches can be installed on all enclosures, including
door opening protection and/or removal from the mounting position. Doors
can be secured using screws or keylock. The PC5200 may be installed
within the same metallic cabinet as the alarm controller/power supply
(model Power UC1, PC5003C) or in a separate enclosure (model
PC4003C). Internal and/or external wiring for this module shall be routed,
supported, clamped or secured in a manner that reduces the likelihood of:
•excessive strain on wire and on terminal connections,
•loosening of terminal connections and
•damage of conductor insulation
NOTE: For EN50131-1 Grade 2 compliant installations, all unused holes on
the side of the cabinet must be covered (plugged). Also, the security tape
must be applied over the hinges of the removeable door in order to prevent
undetected access to the inside of the cabinet.
NOTE: The PC5200 power supply has been certified by Telefication according to EN50131-1:2006 + A1:2009 and EN50131-6:2008, for Grade 2,
Class II, Type A when installed in PC5003C (removable door) enclosure.
PC5200 Jumper Settings
The PC5200 has 2 jumpers; to select which PC5200 slot is to be used refer
to the table below.
Table 2
SLOT J1 J2
PC5200 1 OFF OFF
PC5200 2 ON OFF
PC5200 3 OFF ON
PC5200 4 ON ON
LIMITED WARRANTY
Digital Security Controls warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use
and that in fulfilment of any breach of such warranty, Digital Security Controls shall, at its
option, repair or replace the defective equipment upon return of the equipment to its factory.
This warranty applies only to defects in parts and workmanship and not to damage incurred
in shipping or handling, or damage due to causes beyond the control of Digital Security
Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage
arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of
any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls. This warranty contains the entire warranty.
Digital Security Controls neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any
other warranty or liability concerning this product. In no event shall Digital Security Controls
be liable for any direct or indirect or consequential damages, loss of anticipated profits, loss
of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested
on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product to fail to perform as expected.
IMPORTANT - READ CAREFULLY: DSC SOFTWARE PURCHASED WITH OR
WITHOUT PRODUCTS AND COMPONENTS IS COPYRIGHTED AND IS PURCHASED UNDER THE FOLLOWING LICENSE TERMS:
This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital
Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer
of the integrated security systems and the developer of the software and any related products
or components (“HARDWARE”) which You acquired. If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is
NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE
PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and “online” or electronic documentation. Any software
provided along with the SOFTWARE PRODUCT that is associated with a separate end-user
license agreement is licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE
PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this
EULA is deemed to be a modification of any previous arrangement or contract. If You do not
agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to
You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is
licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one
copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In other words, if You have
several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You
may only have one copy per license installed at any given time. You may use the back-up
copy solely for archival purposes. Except as expressly provided in this EULA, You may not
otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not
reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to
the extent that such activity is expressly permitted by applicable law notwithstanding this
limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or
labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product.
Its component parts may not be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then
the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In
this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in
this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it
available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as
part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You
transfer all of the SOFTWARE PRODUCT (including all component parts, the media and
printed materials, any upgrades and this EULA), and provided the recipient agrees to the
terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also
include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You
fail to comply with the terms and conditions of this EULA. In such event, You must destroy all
copies of the SOFTWARE PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks
or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT
(including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE
PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials
accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to
the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other
intellectual property laws and treaties. This EULA grants You no rights to use such content.
All rights not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE
PRODUCT to any country, person, or entity subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties
agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto,
Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC
DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT
OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems
caused by changes in the operating characteristics of the HARDWARE, or for problems in the
interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY
EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS
LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY
YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00).
BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY
AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR
IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART
OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO
CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY
CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES
SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT
DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE
NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF
THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC
recommends that the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls
could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used
properly, in strict accordance with the manufacturer’s instructions, may cause interference to
radio and television reception. It has been type tested and found to comply with the limits for
Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on
different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician
for additional suggestions. The user may find the following booklet prepared by the FCC
useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet
is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock #
004-000-00345-4.
© 2012 Tyco International Ltd. and its Respective Companies. All Rights Reserved. Toronto, Canada • www.dsc.com • Tech. Support: 1-800-387-3630 (Canada & U.S.), 905-760-3000 Printed in Canada
Loading...