DSC PC1832, PC1616, PC1864 User Manual

Page 1

PowerSeries

PC1616/PC1832/PC1864 version 4.1

Installation Guide

Note to Installer:Center pages contain important end user information. Leave with End User. W ARNING: This man ual contains inf ormation on limitations regar ding pr oduct use an d function and infor-

mation on the limitations as to liability the manufacturer. The entire manual should be carefully read.

Page 2

Table of Contents

Section Description Page

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

2.1

2.2

2.3

2.4

2.5

3.1

3.2

3.3

3.4

3.5

3.6

Installation & Wiring............................................................................................1

Keybus Wiring ..................................................................................................2

Zone Wiring......................................................................................................2

Zone Expanders...............................................................................................2

Bell Wiring........................................................................................................2

AUX Power Wiring............................................................................................4

PGM Wiring......................................................................................................4

Telephone Line Wiring......................................................................................4

Ground.............................................................................................................4

Battery..............................................................................................................4

AC Wiring.........................................................................................................4

User Commands..................................................................................................5

Away Arming ....................................................................................................5

Stay Arming......................................................................................................5

Disarming.........................................................................................................5

[] Commands.................................................................................................5

Function keys...................................................................................................7

Programming .......................................................................................................8

How to Program...............................................................................................8

Programming Toggle Options...........................................................................8

Programming Decimal & Hexadecimal Data....................................................8

How to Exit Programming.................................................................................9

Viewing Programming......................................................................................9

DLS Programming............................................................................................9

4 Programming Descriptions...............................................................................10

5 Programming Worksheets................................................................................25

App A Reporting Code Formats (Contact ID, SIA)..............................................APP A

App B UL Listing Requirements...........................................................................APP B

App C SIA False Alarm Reduction Quick Reference Chart................................APP C

App D Troubleshooting Guide ..............................................................................APP D

Page 3

Section 1: Installation & Wiring

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.

All necessary information required to meet UL Listing requirements is included in this document.

Technical Summary

OUT Of THE BOX

Qty 1  Qty 1  Qty 1  Qty 1  Qty 2  Qty 1  Qty 4 

Qty 16 

Qty 1  Qty 1  Qty 1  Qty 1 

Cabinet PC Module Installation guide User manual Cabinet Label Cabinet Door Plug Standoffs

5.6KΩ Resistors

2.2KΩ Resistor

1.0KΩ Resistor 10Ω Resistor Grounding Kit

SPECIFICATIONS

Temp Range......... 0°C-49°C (32°F-120° F)

Humidity (Max)............................ 93%R.H.

Power Supply........ 16.5VAC/40VA @60Hz

Current Draw (Panel)...........110mA (nom.)

Aux+ Output ........... 11.1-12.6VDC/700mA

Bell Output.............. 11.1-12.6VDC/700mA

FEATURES

On-board Zones 6 8 8

Hardwired Zones 16 (1xPC5108) 32(3xPC5108) 64 (7xPC5108) Wireless Zones 16 32 32 Keypad Zone Support

On-board PGM Outputs PGM 1 - 50mA

PGM Expansion 8x50mA (PC5208)

Keypads 8 8 8

Partitions 2 4 8 User Codes 32 + Master Codes 32 + Master Codes 32 + Master Codes Event Buffer 500 Events 500 Events 500 Events Transformer Required 16.5VAC/40VA 16.5VAC/40VA 16.5VAC/40VA Battery Required 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr Bell Output 12V/700 mA (cont) 12V/700 mA (cont) 12V/700 mA (cont)

PC1616 PC1832 PC1864



PGM 2 - 300mA

4x500 mA (PC5204)

PGM 1 - 50mA PGM 2 - 300mA

8x50mA (PC5208) 4x500 mA (PC5204)

PGM 1, 3, 4 - 50mA PGM 2 - 300mA

8x50mA (PC5208) 4x500 mA (PC5204)

COMPATIBLE DEVICES

Keypads (

PK5500 Keypad ............................................................... 125mA (max.)

PK5501 Keypad ............................................................... 125mA (max.)

PK5508 LED Keypad ....................................................... 125mA (max.)

PK5516 LED Keypad ....................................................... 125mA (max.)

PC5532Z LED Keypad..................................................... 125mA (max.)

LCD5511 Fixed Message LCD Keypad ............................ 85mA (max.)

LED5511Z 8-zone LED Keypad ...................................... 100mA (max.)

PC5003C...........................................222x298x78mm (11.3x11.7x3.0in)

PC500C (residential burg only) ...........213x235x78mm (8.4x9.25x3.0in)

PC4050CAR (UL commercial burg)305x 376x124mm (12.0x14.8x4.9in)

CMC-1 (UL commercial burg) ...........287x297x76mm (11.3x11.7x3.0in)

Refer to the Reference Manual for alternate control cabinets

Backward compatible with all PowerSeries keypads) Modules

T-Link TL150*TL-250/TL300.......................................... 275/350mA

PC5100 2-wire Interface .......... 40mA plus devices to 170mA max.

PC5132-433 Wireless Receiver ........................................... 125mA

RF5108-433 Wireless Receiver ...........................................125mA

PC5108 Zone Expander ......................................................... 30mA

PC5200 Power Supply............................................................ 20mA

PC5204 Power Supply with 4 Programmable Outputs .......... 30mA

Cabinets

PC5208 Low Current Programmable Output Module ............ 50mA

PC5400 Printer/DVAC Module ...............................................65mA

PC5401 Bi-Directional RS232 Module (Not UL Listed) ..........65mA

Escort5580 Telephone Interface Module ............................. 130mA

*The T-Link TL-150 is not UL/ULC listed

Refer to the Reference Manual for additional devices.

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

Installation

Begin the installation by mounting additional modules in the cabinet using the standoffs provided, then mount the cabinet in a dry protected area with access to unswitched AC power. Install Hardware in the sequence indicated in the following pages. Do NOT apply power until installation is complete.

All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4” (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections.

Page 4

PowerSeries - PC1616/PC1832/PC1864

1.1 Keybus Wiring

The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEYBUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel.

The following rules must be followed when wiring the Keybus:

• Minimum 22 AWG wire, maximum 18 AWG (2-wire twisted preferred

•Do NOT use shielded wire

150’ (46m)

• Modules can be home run, connected in series or can be T-tapped provided that the maximum wire distance from the control panel to any module does not exceed 1,000 feet (305m)

• No more than 3,000 feet (915m) of wire can be used in total

CONTROL

PANEL

150’ (46m)

500’ (152m)

1.2 Zone Wiring

Zones can be wired for Normally Open, Normally Closed Contacts with Single-end-of-line (SEOL) resistors or Double End-of-Line

Normally Closed Loops - Do NOT use for UL Installations

(DEOL) resistors. Observe the following guidelines

• For UL Listed Installations use SEOL or DEOL only.

• Minimum 22 AWG wire, maximum 18 AWG

•Do NOT use shielded wire

• Wire run resistance shall not exceed 100Ω. Refer to the chart below.

Single End-of-Line Resistor Wiring

Burglary Zone Wiring Chart

Wire

Gauge

22 3000 / 914 20 4900 / 1493 19 6200 / 1889 18 7800 / 2377

Figures are based on maximum wiring

• Section [001-004] Selects Zone Definition

• Section [013] Opt [1] Selects Normally Closed or EOL resistors

• Section [013] Opt [2] Selects Single EOL or Double EOL resistors.

Maximum wire Length to

End-of-line Resistor

(feet/meters)

resistance of 100 Q

Double End-of-Line Resistor Wiring

Zone Status - Loop Resistance/Loop Status

• Fault - 0Ω (shorted wire/loop)

• Secure - 5600Ω (contact closed)

• Tamper - infinite (broken wire, open)

• Violated - 11,200Ω (contact open)

1.3 Zone Expanders

Zone expanders add zones in groups of eight to the Alarm system. Module jumpers J1,J2,J3 are required to assign zones to these modules. Jumper settings for PC5108v2 are shown here.

• PC5108v1.0 supports first 32 zones only.

• PC5700 enrolls as two modules

• Do NO T use PC5108v1 &v2 on the same

panel.0

Module Zones Jumpers J1 J2 J3

ON ON ON Zones Disabled OFF ON ON Zones 09-16 ON OFF ON Zones 17-24 OFF OFF ON Zones 25-32 ON ON OFF Zones 33-40 OFF ON OFF Zones 41-48 ON OFF OFF Zones 49-56 OFF OFF OFF Zones 57-64

Assigned

Refer to to the associated installation sheet for Jumper locations for the PC5108v1, or PC5700

1.4 Bell Wiring

These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6 VDC for residential installations (e.g.DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern requirements: Program Section [013] Opt [8] ON.

NOTE: Steady, Pulsed alarms are also supported.

The Bell output is supervised and power limited by 2A PTC. If unused, connect a 1000Ω resistor across Bell+ and Bell- to prevent the panel from displaying a trouble. See [][2].

Page 5

PC1616/1832/1864 Wiring Diagram

220

1. Insert Stand off into cabinet mounting hole in the desired location. Snap-inplace.

2. Position circuit board mounting holes over standoffs.Press firmly on board to snap-in-place.

PC Board

Cabinet

Stand Off

Primary:120VAC/60Hz. Secondary: 16.5VDC 40VA DSCPTD 1640U Class II Transformer

NOTE:Do not connect transformer to receptacle controlled by a switch

North America Only

POWER LIMITED

CableTie (not supplied) recommended

UA503

PC1616/1832/1864

220

WARNING:

HighVoltage.Disconnect AC Power

and telephone lines before servicing

Installation

DSC

230V /50 Hz International

CON1

BAT+BAT-

AC AC

To EGND

16.5V /40VA

FUSE

Terminal

IMPORTANT:

a)This equipment, Alarm Controller PC1616/1832/1864 shall

be installed and used within an environment that provides the pollution degree max 2 and overvoltages category II NON-HAZARDOUS LOCATIONS, indoor only. The equipment is FIXED and PERMANENTLY connected and is designed to be installed by service persons only; [service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons.]

b)The connection to the mains supply must be made as per the local

authorities rules and regulations. An appropriate disconnect device must be provided as part of the building installation.Where it is not possible to rely on identification of the neutral in the AC Mains supply the disconnecting device must disconnect both poles simultaneously (line and neutral). The device shall disconnect the supply during servicing.

c)The equipment enclosure must be secured to the building structure

before operation.

e)Internal wiring must be routed in a manner that prevents:

- Excessive strain on wire and on terminal connections;

- Loosening of terminal; connections;

- Damage of conductor insulation

f) Disposal of the used batteries shall be made according to the waste

recovery and recycling regulations applicable to the intended market.

g) Before servicing, DISCONNECT the telephone connection.

WARNING:

HighVoltage.Disconnect AC Power

and telephone lines before servicing

PC1864

CON1

BAT+BAT-

AUX+ BELL+

AC AC RED BLKYEL GRN Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8

AUX- BELL-

PGM1 PGM3

PGM2 PGM4

Only

PC1864 PC1832

Only

RING R-1

EGND

TIP T-1

See Section 9 for ground wiring details

TB-2

12V / 7 AHr 12V / 7 AHr

BLACK

RED

PC1864

Only

PGM2 PGM4

DSC Model BD7-12

or equivalent

Battery

StandbyTime:

24Hrs min.

REV XX

UA503

Internally Connected

DSC

PC-LINK

PC1864 PC1832

Only

RING R-1

EGND

TB-2

TIP T-1

NON-POWER LIMITED

WARNING:

Inspect wiring and ensure connections are correct before applying power. Incorrect connection of batteries may result in battery rupture or Fire Hazard.

Do NOT allow metal objects to connect the Positive and Negative Terminals. Ensure that batteries are connected with correct polarity [Red to (+), Black to (-)]. Failure to comply with this may result in battery rupture and/or Fire Hazard. All circuits are classified for UL Installations as Power Limited/Class II Power Limited except for battery leads which are not power limited.

Do NOT route any wiring over circuit boards. Maintain at least 1"(25.4mm) separation. A minimum of 1/4" (6.4mm) separation must be maintained at all points between power limited wiring and all other non-power limited wiring.

220

AUX+ and Keybus (Red) are Internally Connected Total current draw from Keypads, PGM Outputs and Aux circuits must not exceed 700mA

CON1

BAT+BAT-

AC AC RED BLKYEL GRN Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8

Incorrect connections may result in PTC failure or improper operation.

PC1616/1832/1864

AUX+ BELL+

AUX- BELL-

PGM1 PGM3

98431

See corresponding Section NumberText for wiring details.

Page 6

PowerSeries - PC1616/PC1832/PC1864

1.5 AUX Power Wiring

The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc. If the total current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below.

Min/max operating voltages for devices, sensors and modules is 9.5V

DC - 14VDC

Refer to the list of Compatible Devices on page 1 and/or the Reference Manual for the current draw of individual devices

1.6 PGM Wiring

PGMs switch to ground when activated by control panel. Connect the positive side of the device to be activated to the AUX+ Terminal. Connect the negative terminal to the PGM. current output is as follows

• PGM 1, 3, 4............................................................................... 50mA

• PGM 2..................................................................................... 300mA

2-wire Smoke Detectors Initiating Circuit

• Style B (Class B), Supervised, Power Limited

• UL Compatibility Identifier .................................................... PC18-1

• DC Output Voltage........................................................9.8-13.8 VDC

• Detector Load ............................................................... 2mA (MAX)

• Single-end-of-line (SEOL) Resistor ........................................ 2200Ω

• Loop Resistance.............................................................. 24Ω (MAX)

• Standby Impedance..................................................... 1020Ω (ΝΟΜ)

• Alarm Impedance.......................................................... 570Ω (MAX)

• Alarm Current .............................................................. 89mA (MAX)

For currents levels greater than 300mA a relay is required. PGM2 can also be used for 2-wire smoke detectors.

NOTE: Use SEOL resistors on Fire Zones ONLY. PGM 1, LED output with current limiting resistor and

Optional Relay driver output

UL Compatibility ID For FSA-210B Series is: FS200

NOTE: For ULC Listed installations use FSA-210A and FSA-410A series

4-wire Smoke Detectors

RM-1/RM-2 POWER LOOP

SUPERVISORY RELAY

1.7 Telepho ne Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ31x Connector as indicated. Use 26 AWG wire minimum for wiring.

For connection of multiple devices to the telephone line, wire in the sequence indicated. Telephone format is programmed in section [350].

R-1 TIP

RING

T-1

RJ-31X

Telephone Call Directions are programmed in section [351]-[376].

1.8 Ground 1.9 Battery 1.10 AC W i r i n g

Ground Installation A sealed, rechargeable, lead acid

Tighten nut to break paint and make

good connection to the cabinet

NOTE: Do not connect transformer to a receptacle controlled by a switch. (UL Listed Installations Only)

battery or gel type battery is required to meet UL requirements for power standby times. NOTE: UL Residential/Commercial Burglary installations require 4Hrs Power Standby time. NOTE: UL/ULC Residential Fire & Health Care installations require 24 Hr. power standby. ULC Commercial Burglary and Fire monitoring installations require 24 Hr. power standby.

Standby Battery Guide

Battery Charging Current: 400 mA

Batt Standby Size 4Hr 24Hr

-------------------------------------------------

4Ahr 700mA --- 7Ahr 700mA 180mA 14Ahr 700mA 470mA

NOTE: Battery capacity will deteriorate with age and number of charge/discharge cycles. Replace every 3-5 years.

AC Wiring UL Listed

Installations Primary: 120VAC/

60Hz./0.33A Secondary:

16.5VAC/40VA DSC PTD 1640U Plug-in, Class 2 Transformer. Use DSC PTD 1640U for Canadian Installations

Page 7

Section 2: User Commands

Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section describes basic keypad commands. Refer to the PC1616/1832/1864 Reference Manual for detailed description of all keypad commands.

Press the

Section 2.1 – Away Arming

The Ready light must be ON to arm the system. If the Ready light is OFF, ensure all protected doors and windows are secure or bypassed. To arm the system in the Away mode, either press and hold the Away function button for 2 seconds or enter a valid user code and leave the premises through a door programmed as Delay. Upon arming, the Armed light will turn ON. If a user code was used to arm the system and Stay/Away zones are programmed, the Bypass light will turn ON and will turn OFF when a door programmed as Delay is violated. If the Audible Exit Delay option is enabled, the keypad will beep once every second during the exit delay (and three times a second during the last 10 seconds) to alert the user to leave.

Section 2.2 – Stay Arming

The Ready light must be ON to arm the system. If the Ready light is OFF ensure all protected doors and windows are secure or bypassed. To arm the system in the Stay mode, either press and hold the Stay function button for 2 seconds or enter a valid user code and stay within the premises (do NOT violate a door programmed as Delay). Upon arming, the Armed light and Bypass light will turn ON. If the Stay function button is used, the keypad will not beep during the exit delay to avoid annoying the person staying in the premises. If a user code was used, the keypad will beep if the Audible Exit Delay option is enabled.

Section 2.3 – Disarming

The user must enter through a door programmed as Delay. Upon entering, the keypad will emit a steady tone (and emit a pulsing tone during the last 10 seconds of entry delay) to alert the user to disarm the system. Enter a valid user code to disarm the system. If an alarm occurred while the panel was armed, the Memory light and the zones that went into alarm will be flashing (LED keypad) or the keypad will display ‘Alarm in Memory’ (LCD keypad). Press the [#] key to return the keypad to the Ready state.

[#] key to reset the keypad if an error has been made entering user codes or keypad commands.

Section 2.4 – [4] Commands

The following is a list of the [4] commands available and a description of each:

[4][1] Bypass (disarmed state)/Reactivate Stay/Away Zones (armed state) [4][2] Display Trouble Conditions [4][3] Display Alarm Memory [4][4] Door Chime Enable/Disable [4][5] User Code Programming [4][6] User Commands [4][7][x] Command Functions 1 – 4 [4][8] Installer Programming [4][9][code] No-Entry Arming [4][0] Quick Arm (disarmed state)/Quick Exit (armed state)

[4][1] Bypass/Re-activate Stay/Away Zones

LED Keypad:

Press [4][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The Bypass light will flash. The keypad will turn ON the corresponding zone light to indicate a zone is bypassed. To bypass or unbypass a zone, enter the 2-digit zone number. Once the correct zones are bypassed, press [#] to exit. The Bypass light will be ON if any zones are manually bypassed.

LCD Keypad:

Press [4][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The keypad will display ‘Scroll to View Zones’. The keypad will display the programmed zone labels for the zones and include the letter ‘O’ in the bottom, right corner if the zone is violated or the letter ‘B’ if the zone is bypassed. Scroll to the appropriate zone and press the [4] key to change the bypass status (or enter the 2-digit zone number). Once the correct zones are bypassed, press [#] to exit.

Additional Bypass Commands:

Bypass Recall: Press [99]. The keypad will recall the last group of zones that were bypassed Clear Bypass: Press [00]. The keypad will clear the bypass on all zones. Save Bypass: Press [95]. The keypad will save which zones are manually bypassed. Recall Save: Press [91]. The keypad will recall the bypassed zones that were saved.

Re-activate Stay/Away Zones:

Press [4][1] when the system is armed in the Stay mode to change the armed status to Away mode. The system will add the Stay/Away zones back into the system after the exit delay time expires.

Page 8

PowerSeries - PC1616/PC1832/PC1864

[4][2] Trouble Display

Refer to Appendix D – Trouble Conditions, for troubleshooting assistance and a detailed description of all trouble conditions.

[4][3] Alarm Memory Display

The Memory light will be ON if an alarm occurred during the last armed period. Press [4][3]. The Memory light will flash and the keypad will display the zones that went into alarm.

: To clear the Memory light, arm then disarm the system.

[4][4] – Door Chime Enable/Disable

Press [4][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled. The same function can be performed by pressing and holding the Chime function button for 2 seconds.

[4][5] – Program User Codes

The following table identifies available user codes:

Code Type Function

[01] – [32] [33] – [34] [40] [41] – [42]

General User Codes Duress Codes Master Code Supervisor Codes

arm, disarm transmit duress reporting code all functions arm, disarm, program user codes

Programming User Codes:

LED Keypad:

Press [4][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone light to indicate a user code is programmed. Enter the 2-digit user to be programmed. The zone light will flash. Enter a new 4 or 6-digit user code or press [4] to delete the user code. After the user code is programmed or deleted, you may enter another 2-digit user to be programmed or press [#] to exit.

LCD Keypad:

Press [4][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right corner if the user code is programmed. Scroll to the appropriate user and press the [4] key to program the user (or enter the 2-digit user num- ber). Enter a new 4 or 6-digit user code or press [4] to delete the user code. After the user code is programmed or deleted, scroll to another user or press [#] to exit.

Programming Partition Assignment:

Press [4][5] followed by the Master Code or Supervisor Code. Press [8] followed by the 2-digit user to change to the partition assignment. The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is ON, the user is assigned to partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [8] followed by the 2-digit user number. When finished, press [#] to exit.

Programming User Attributes:

Press [4][5] followed by the Master Code or Supervisor Code. Press [9] followed by the 2-digit user to change to the user attributes. The keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.

Light [1] For Future Use Light [2] For Future Use Light [3] User can manually bypass zones Light [4] User can access the Escort5580 module remotely Light [5] For Future Use Light [6] For Future Use Light [7] The panel will squawk the bell output when the user arms/disarms Light [8] One-time use code – the code will be erased after it is used to arm/disarm the system

To change the user attributes, press the number corresponding to the attribute. Once the correct attributes are assigned to the user, press [#] to exit. To change the user attributes for another user, press [9] followed by the 2-digit user number. When finished, press [#] to exit.

Page 9

Section 2: User Commands

[4][6] – User Functions

Press [4][6] followed by the Master Code, then press the number corresponding to the following functions.

[1] Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time using

military standard (e.g., 8:00 pm = 20:00 hours).

[2] Auto-arm Enable/Disable: The keypad will emit 3 rapid beeps if the Auto-arm feature is now enabled and a steady 2-second tone

if it is now disabled.

[3] Auto-arm Time/Day: Press the number corresponding to the day of the week (1=Sunday, 2=Monday etc.) followed by the auto-

arm time. Program the time using military standard (e.g., 8:00 pm = 20:00 hours).

[4] System Test: The panel will perform the following; activate the bell output, keypad buzzer and all keypad status lights for 2

seconds, test the backup battery and transmit a reporting code to the central station (if programmed).

[5] Enable DLS: The panel will temporarily enable DLS for 6 hours.

[6] User Initiated DLS: The panel will attempt to call the DLS computer.

[7]-[8] For Future Use

For LCD Keypads: Scroll to the desired option then press [4]

Additional Alphanumeric Keypad Functions:

When scrolling through the list of available functions, the following additional functions are available:

Event Buffer: Used to view the 500-event panel buffer Brightness Control: Used to adjust the display backlighting level for optimal viewing Contrast Control: Used to adjust the display contrast level for optimal viewing Buzzer Control: Used to adjust the keypad buzzer tone for optimal sound

For the PC5508, PC5516, PC5532 and LCD5501 LED keypads, Press and hold the [4] key to adjust the keypad buzzer tone, then release the button. For the PK series keypads, enter [4][6][Master Code] then use the left arrow button (<) to scroll to the desired buzzer tone and use the right arrow button (>) to adjust the backlighting level. When finished, press [#] to exit.

[4][7][x] – Command Output (1-4)

Press [4][7][x]. If the Command Output Code Required option is enabled, enter a valid user code. The panel will activate any PGM output assigned to the command output.

[4][8] – Installer Programming

Press [4][8] followed by the Installer Code to enter Installer Programming. Refer to the ‘How to Program’ section for more information.

[4][9][User Code] – No-Entry Arming

Press [4][9] followed by a valid user code. The system will arm in the Stay mode and after the exit delay expires, it will remove entry delay. All zones programmed as Delay will function like Instant zones. The system will flash the Armed light to indicate that the system is armed with no entry delay.

[4][0] – Quick Arm/Quick Exit

Quick Arm: When disarmed, press [4][0] to arm the system. The system will arm as if a valid user code was entered. Quick Exit: When armed, press [

once during the following 2 minute time period without changing the status of the system.

4][0] to activate Quick Exit. The system will allow a single zone programmed as Delay to be violated

Section 2.5 – Function Keys

Keypads have 5 programmable one-touch function buttons located in a column down the right-side of the keypad. These buttons can also be activated by pressing and holding number [1] through [5] respectively for 2 seconds. The default for these function buttons on the PK series keypads are as follows:

[1] Stay Arm [4] Fire Reset – Command Output 2 [2] Away Arm [5] Quick Exit [3] Chime Enable/Disable

Page 10

PowerSeries - PC1616/PC1832/PC1864

Section 3: Programming

This section provides the information necessary to program all required features for a basic system as well as common applications. Refer to the PC1616/1832/1864 Reference Manual for a complete description of all programmable features.

3.1 How to Program:

DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This will reduce the time required to program and will help eliminate errors.

To enter Installer Programming press [][8][Installer Code]. The Program light will FLASH (programmable LCD keypad displays will change to ‘Enter Section’). An error tone indicates the installer code entered is incorrect, Press [#] to clear any key presses and try again.

The default Installer Code is [5555].

The Armed and Ready lights indicate programming status:

Armed Light ON Panel waiting for 3-digit section number

If in module programming, waiting for section # to be entered.

Ready Light ON Panel waiting for data to be entered Ready Light FLASHING Panel waiting for HEX data to be entered

You cannot enter installer programming while the system or any partition is armed or in alarm.

3.2 Programming Toggle Options:

Enter the 3-digit programming section number.:

• The Armed light will turn OFF and

• The Ready light will turn ON.

• The keypad will display which toggle options are ON or OFF according to the chart.

• To toggle an option ON or OFF, press the corresponding number on the keypad. The display will change accordingly.

Keypad Type

LED Fixed-Message LCD Indicator # ON Indicator # OFF Programmable-Message LCD # Displayed Dash [-] Displayed

Option ON Option OFF

Zone Light ON Zone Light OFF

• When all the toggle options are configured correctly, press the [#] key to exit the program section.

• The Ready light will turn OFF and the Armed light will turn ON.

3.3 Programming Decimal and Hexadecimal (HEX) Data:

• Enter the 3-digit programming section number.

• The Armed light will turn OFF and The Ready light will turn ON.

• Enter the data written in the boxes.

For sections that require multiple 2 or 3 digit numbers, the keypad will double-beep after each 2 or 3 digit entry and move to the next item in the list. After the last digit in the section is entered, the keypad will beep rapidly 5 times and exit the program section. The Ready light will turn OFF and the Armed light will turn ON.

For sections that do not require data for every box (such as phone numbers) press the [#] key to exit the program section after entering all the required data. The Ready light will turn OFF and the Armed light will turn ON.

At any time the [#] can be pressed to exit any program section. All changes made up to that point will be saved.

Value Enter Telephone Dialer

HEX (or hexadecimal) digits are sometimes required. To enter a HEX digit, press the [] key to begin HEX programming. The Ready light will FLASH. Refer to the chart below and press the number corresponding to the HEX digit required. The Ready light will continue to FLASH. Press [

] again to return to normal decimal

programming. The Ready light will turn ON.

HEX [A] HEX [B] HEX [C] HEX [D] HEX [E] HEX [F]

Press [][1][] Press [][2][] Press [][3][] Press [][4][] Press [][5][] Press [][6][]

Not Supported Simulated [] key Simulated [#] key Dial tone search Two second pause Not Supported

In addition to the standard digits 0-9, HEX digits and special dialer functions can also be programmed if required.

3.4 How to Exit Installer Programming:

To exit installer programming, press the [#] key when the panel is waiting for a 3-digit section number (the Armed light is ON).

Page 11

Section 3: Programming

3.5 Viewing Programming

LED and LCD5501Z Keypads

Any programming section can be viewed from an LED or

LCD5501Z keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section.

The keypad displays the information using a binary format, accord-

ing to the following chart:

Press any of the Emergency keys (Fire, Auxiliary or Panic) to

advance to the next digit.

When all the digits in a section have been viewed, the panel will exit the section: the Ready light will turn OFF, and the Armed

light will turn ON, waiting for the next 3-digit programming section number to be entered.

Press the [#] key to exit the section

LCD Keypad

The keypad will immediately display all the information programmed when a programming section is entered. Use the arrow keys (< >)

to scroll through the data being displayed. Scroll past the end of the data displayed, or press the [#] key to exit the section.

3.6 DLS Programming

Hardware Setup - Local (PC-Link) Connect an RS-232 to PC-Link Cable between the Computer with DLS Software installed and the alarm panel to be programmed.

Enter the following at a system Keypad to initiate PC-Link:

• Enter Installers programming [

][8][Installer Code][499][Installer Code][499]

Page 12

PowerSeries - PC1616/PC1832/PC1864

Section 4 – Programming Descriptions

The following is a brief description of the features and options available in the Power PC1616/1832/1864 control panel. Refer to the PC1616/ 1832/1864 Reference Manual for a complete description of all programming features, limitations and requirements.

Section [001] to [004] Zone Definitions

Option Description

[00] Null Zone: Zone not used

[01] Delay 1: When armed, provides entry delay when violated (follows Entry Delay 1)

[02] Delay 2: When armed, provides entry delay when violated (follows Entry Delay 2)

[03] Instant: When armed, instant alarm when violated

[04] Interior: When armed, instant alarm if the zone is violated first, will follow entry delay if entry delay is active

[05] Interior Stay/Away: Similar to ‘Interior’ except panel will auto-bypass the zone if Armed in the Stay mode

[06] Delay Stay/Away: Similar to ‘Delay 1’ except panel will auto-bypass the zone if Armed in the Stay mode

[07] Delayed 24-Hour Fire (Hardwire): Instant audible alarm when violated, communication delayed 30 seconds - if alarm

acknowledged during this time (by pressing a key), the alarm will be silenced 90 seconds and repeat cycle - if not, alarm will latch and communicate after 30 second delay

[08] Standard 24-Hour Fire (Hardwire): Instant alarm and communication when violated

[09] 24-Hour Supervision (Hardwire): Instant alarm, panel will activate keypad buzzer instead of bell output

[10] 24-Hour Supervisory Buzzer: Instant alarm, panel will activate keypad buzzer instead of bell output

[11] 24-Hour Burglary: Instant alarm when violated, audible alarm at default. Reporting code BA, BH

[12] 24-Hour Hold-Up: Instant alarm when violated, silent alarm at default. Reporting code HA, HH

[13] 24-Hour Gas: Instant alarm when violated, audible alarm at default. Reporting code GA, GH

[14] 24-Hour Heat: Instant alarm when violated, audible alarm at default (also known as high-temp). Reporting code KA, KH

[15] 24-Hour Medical: Instant alarm when violated, silent alarm at default. Reporting code MA, MH

[16] 24-Hour Panic: Instant alarm when violated, audible alarm at default. Reporting code PA, PH

[17] 24-Hour Emergency: Instant alarm when violated, audible alarm at default. Reporting code QA, QH

[18] 24-Hour Sprinkler: Instant alarm when violated, audible alarm at default. Reporting code SA, SH

[19] 24-Hour Water: Instant alarm when violated, audible alarm at default (also known as high water level). Reporting code WA, WH

[20] 24-Hour Freeze: Instant alarm when violated, audible alarm at default (also known as low-temp). Reporting code ZA, ZH

[21] 24-Hour Latching Tamper: Instant alarm when violated, panel cannot be armed until Installer Programming is entered

[22] Momentary Keyswitch Arm: Arm or disarm the system when violated

[23] Maintained Keyswitch Arm: Arm system when violated, disarm system when restored

[24] For Future Use

[25] Interior/Delay: Zone will function like an Interior zone when armed in Away mode, like a Delay zone when armed in the Stay

mode

[26] 24-Hour Non-Alarm: Zone will NOT create an alarm. Can be used with zone follower function for automation applications

[29] Auto-Verified Fire: When violated, system will reset all smoke detectors for 20 seconds, then wait 10 seconds for detectors to

settle. If another fire alarm detected within 60 seconds zone will go into alarm immediately

[30] Supervisory: Instant alarm, system will activate keypad buzzer. A valid user code is required to silence Keypad buzzer.

[31] Day Zone: Instant alarm when system is armed, keypad buzzer (no alarm) when system is disarmed

[32] Instant Stay/Away: Similar to ‘Instant’ except panel will auto-bypass the zone if Armed in the Stay mode

[35] 24-Hour Bell/Buzzer: Instant alarm when violated, system will activate bell output if armed, keypad buzzer if disarmed

Page 13

Section 4 – Programming Descriptions

[37]

[87] Delayed 24-Hour Fire (Wireless): Same as Delayed 24-Hour Fire (Hardwire) but must be used for wireless smoke detectors

[88] Standard 24-Hour Fire (Wireless): Same as Standard 24-Hour Fire (Hardwire) but must be used for wireless smoke detectors

Night Zone: Functions like Interior Stay/Away but will remain bypassed if the user presses [

when armed in the Stay mode

][1] to re-activate Stay/Away zones

Section [005] System Times

After entering Section [005], enter the 2-digit subsection number for the desired partition and program the Entry Delay 1, Entry Delay 2 and Exit Delay for each active partition on the system. Valid entries are from [001] to [255] or [045] to [255] for SIA CP-01 panels (in seconds). Enter subsection [09] to program the Bell Cut-Off Time. Valid entries are from [001] to [255] (in minutes).

Section [006] Installer Code

The default Installer Code is [5555] or [555555] if 6-Digit Access Codes is enabled.

Section [007] Master Code

The default Master Code is [1234] or [123456] if 6-digit Access Codes is enabled.

Section [008] Maintenance Code

The default Maintenance Code is [AAAA] (not programmed). This code can arm any partition but cannot disarm unless the partition is in alarm.

Section [009] to [011] PGM Outputs

The PC1616 and PC1832 have two on-board PGM outputs (PGM1 and PGM2). The PC1864 has four on-board PGM outputs (PGM1 to PGM4). The panel has the capacity for up to 14 PGM outputs (8 additional low-current PGM outputs with PC5208 module, 4 additional high-current PGM outputs with a PC5204 module).

PGM Output Options:

Option Description

[00] For Future Use

[01] Fire and Burglary: Output will activate (steady for burglary, pulsing for fire) if an alarm occurs on the selected partition

[02] For Future Use

[03] Sensor Reset: Output will normally be active and deactivate for 5 seconds when a [][7][2] fire reset command is entered or when an Auto-

Verify Fire alarm is detected

[04] 2-Wire Smoke: Configures PGM2 as 2-wire smoke detector input (PGM2 only)

[05] Armed Status: Output will activate when all of the selected partitions are armed

[06] Ready Status: Output will activate when all the selected partitions are in the Ready state (Ready light ON)

[07] Keypad Buzzer Follow: Output will activate and follow the keypad buzzer for the selected partition when the following events occur; entry

delay, door chime, audible exit delay, automatic arming pre-alert, 24-Hour Supervisory Buzzer zone alarm

[08] Courtesy Pulse: Output will activate during entry/exit delay if the selected partition is armed – will remain active for an additional 2

minutes after the entry or exit delay expires

[09] System Trouble: Output will activate when any selected trouble condition is present

[10] Latched System Event (Strobe): Output will activate when a selected condition occurs on any selected partition. Note output can be

programmed to follow timer

[11] System Tamper: Output will activate when any tamper condition is present

[12] TLM and Alarm: Output will activate if a telephone line trouble is present and then an alarm occurs

[13] Kissoff: Output will activate for 2 seconds when a valid kissoff is received from the central station

[14] Ground Start: Output will activate for 2 seconds when the panel attempts to seize the phone line (additional dial tone search must be

programmed in the central station phone number – HEX [D])

[15] Remote Operation: Output can be activated/deactivated via the DLS software

[16] For Future Use

[17] Away Armed Status: Activates when all of the selected partitions are armed in Away mode

[18] Stay Armed Status: Activates when all of the selected partitions are armed in Stay mode

[19] Command Output 1:Activates when a [][7][1] command is entered on the selected partition – Command can be programmed to require a

valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

Page 14

PowerSeries - PC1616/PC1832/PC1864

[20] Command Output 2: Activates when a [][7][2] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[21] Command Output 3: Activates when a [][7][3] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[22] Command Output 4: Activates when a [][7][4] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[23] Silent 24-Hour Input: Changes PGM to a 24-Hour Silent zone (PGM2 only)

[24] Audible 24-Hour Input: Changes PGM to a 24-Hour Audible zone (PGM2 only)

[25] Delayed Fire and Burglary: Functions as a Fire and Burglary output but does not activate until the TX Delay time expires

[26]-[28] For Future Use

[29] Zone Follower: Active when all the selected zones (1-8) are restored and activates when any of the selected zones are violated

[30] Partition Status Alarm Memory: Activates if the selected partition is armed.

Output will pulse “one second ON / one second OFF if an alarm occurs

Section [012] Keypad Lockout

The system can be programmed to ‘lockout’ keypads if a series of incorrect user or installer codes are entered. When lockout is active, all keypads emit a steady 2-second error tone when a key is pressed. Program the Number of Invalid Codes Before Lockout with the desired number. Valid entries are from [000] to [255]. Program data [000] to disable the feature. Keypads will remain locked out for the number of minutes programmed for the Lockout Duration. Valid entries are from [000] to [255].

Section [013] First System Option Code

Option Description

[1] ON: zones require normally-closed loops. OFF: zones require 5.6K End-Of-Line resistors.

[2] ON: zones require double End-Of-Line resistors. OFF: zones require single End-Of-Line resistors.

[3] ON: keypads will display all trouble conditions while armed. OFF: keypads will only display fire trouble when armed.

This option must be OFF if LCD5500 v2.x (or older) keypads are used on the system.

[4] ON: only a trouble will be displayed. OFF: keypads will display a trouble and a zone violation if a tamper or fault is detected.

[5] ON: auto-arming schedules (Program Sections [181]-[188]) will be available to the user in the [][6] menu.

OFF: auto-arming schedules will NOT be available to the user in the [][6] menu.

[6] ON: the Audible Exit Fault feature will be enabled. If a delay zone is not secured correctly and not force-armed, at the end of the exit delay,

the system will go into entry delay and turn ON the bell output. OFF: the keypad will sound the entry delay through the keypad as normal.

[7] ON: the system will NOT log additional alarms for a zone that has reached the swinger shutdown threshold.

OFF: all zone alarms will be logged.

[8] ON: Temporal Three Fire Signal is used to annunciate fire alarms

(½ second ON, ½ second OFF, ½ second ON, ½ second OFF ½ second ON, 1 ½ seconds OFF).

OFF: the system will pulse the bell output

(½ second ON, ½ second OFF).

Page 15

Section 4 – Programming Descriptions

Section [014] Second System Option Code

Option Description

[1] ON: the system squawks the bell output once when a partition is armed, twice when disarmed. OFF: the bell output does not

activate.

[2] ON: the system squawks the bell output every 10 seconds during the auto-arm pre-alert. OFF: the bell output does not activate.

[3] ON: the system will squawk the bell output once every second during Exit Delay, 3 squawks per second for the last 10 seconds.

OFF: the bell output will not activate.

[4] ON: the system will squawk the bell output once every second during Entry Delay, 3 squawks per second for the last 10 seconds.

OFF: the bell output will not activate.

[5] ON: the system squawks the bell output once every 10 seconds when a trouble condition is present.

OFF: the bell output does not activate.

[6] ON: the system will beep the keypads once every second, and 3 times a second during the last 10 seconds, during exit delay when

the system is armed with a user code or armed in the Away mode. OFF: the keypads will not beep.

[7] ON: the exit delay will be terminated when a Delay 1 zone is violated and restored after the system is armed.

OFF: the exit delay will count down as normal.

[8] ON: the bell output will not timeout if a fire alarm occurs. The user must turn OFF the bell by entering a valid user code.

OFF: the bell output will timeout normally.

Section [015] Third System Option Code

Option Description

[1] ON: the keypad [F] fire emergency key will be enabled. OFF: the keypad [F] fire emergency key will be disabled.

[2] ON: the keypad [P] panic emergency will be audible (bell output). OFF: the keypad [P] emergency key will be silent.

[3] ON: the Quick Exit feature will be enabled. OFF: the Quick Exit feature will be disabled.

[4]

[5]

[6] ON: the Master Code (user code 40) can only be changed in Installer Programming. OFF: the Master Code can be changed using

[7] ON: the system supervises the telephone line and displays a trouble if disconnected. OFF: the telephone line is not supervised.

[8] ON: the system activates the bell output if a telephone line trouble is detected while the system is armed. OFF: the system activates

ON: the Quick Arming [

If this feature is disabled, a valid user code must be entered after the Stay or Away function buttons are pressed.

ON: a valid user code must be entered after pressing [

the User Programming [

the keypad buzzer trouble tone.

][0] feature will be enabled. OFF: Quick Arming [][0] feature will be disabled.

][1] to access the Bypass feature. OFF: a user code is not required.

][5] command.

Section [016] Fourth System Option Code

Option Description

[1] ON: the system supervises the AC input and displays a trouble if a failure is detected. OFF: AC Input is not supervised.

[2] ON: the trouble light will flash when an AC trouble is detected. OFF: the trouble light turns on, does not flash.

[3] ON: the keypad blanks (no indicator lights) if a key is not pressed for 30 seconds. OFF: the keypad does not blank.

[4] ON: a valid user code must be entered to restore normal keypad operation after the blanking. OFF: pressing any key will return the

keypad to normal operation.

Page 16

PowerSeries - PC1616/PC1832/PC1864

[5] ON: keypad backlighting enabled. OFF: keypad backlighting disabled.

[6] ON: the system temporarily enables the Keypad Blanking feature if an AC failure is detected (to preserve the back up battery).

OFF: the system will operate as normal.

[7] ON: the keypad turns ON the Bypass light if zones are bypassed while the system is armed. OFF: the Bypass light turns OFF when

the system is armed.

[8] ON: the system supervises keypad tampers. OFF: the system does not supervise keypad tampers.

Section [017] Fifth System Option Code

Option Description

[1] ON: the system does NOT associate wireless keys to user codes. OFF: the system will assign user code 17 to wireless key #01,

user code 18 to wireless key #02 etc. If the wireless key is used to arm or disarm, the system will report the Opening or Closing for the associated User Code.

[2] ON: the system generates an RF Jam trouble condition if the condition is present for 5 minutes. OFF: the system generates the

trouble condition after 30 seconds.

[3] ON: the keypads beep if an RF Jam trouble is detected. OFF: the trouble is not annunciated via the keypad buzzer.

[4] ON: the Double Hit feature will be enabled. Two violations from the same zone within the Cross Zone Timer will be considered a

valid Police Code or Cross Zone event. The system will report the event and log it to the event buffer.

OFF: two alarms from the same zone is not a valid Police Code or Cross Zone event.

[5] ON: the system logs and communicates a Late-To-Close event when it auto-arms at the programmed time (not if auto arming was

caused by the No-Activity Arming feature). OFF: the system does not transmit or log a Late-To-Close event.

[6] ON: enables the Daylight Savings automatic clock adjustment feature. OFF: the system does not automatically adjust the clock for

Daylight Savings.

[7] For Future Use

[8] ON: the system only squawks the bell output when the system is armed in the Away mode. OFF: the system squawks the siren

when the system is armed in any mode. (See Section [14]).

Section [018] Sixth System Option Code

Option Description

[1] ON: the system only transmits a Test Transmission reporting code if no other event was transmitted to the central station during the

programmed time. OFF the system always transmits a Test Transmission reporting code as programmed.

[2]-[4] For Future Use

[5] ON: the keypad buzzer follows the bell output for all alarms. OFF: the system only activates the bell output for all alarms.

[6] ON: When an alarm is detected on a zone (with the Cross Zone attribute enabled), a timer is started. The alarm is not transmitted and

the bell output is not activated unless a second cross zone enabled zone is violated before the Cross Zone timer times out. OFF: the system reports all alarms normally and logs and transmits a Police Code reporting code if a second zone alarm is detected during the armed period.

[7] ON: the system restarts the Exit Delay (one time) if a Delay zone is violated and restored during the exit delay time. OFF: exit

delay does not restart.

[8] ON: the system activates the trouble beeps when an AC trouble is detected. OFF: the system does not annunciate AC troubles

using the keypad buzzer.

Section [019] Seventh System Option Code

For Future Use

Page 17

Section 4 – Programming Descriptions

Section [020] Keypad Zone Assignment

Enter the two-digit zone number to be assigned to each keypad assigned to a specific slot. Only one keypad can be assigned to a specific slot. See Keypad Assignment. Valid entries are from [00] to [64].

Section [021] Eighth System Option Code

For Future Use

Section [022] Ninth System Option Code

Option Description

[1-5] For Future Use

[6] Refer to the PC1616/PC1832/PC1864 Reference Manual for RF Delinquency details.

[7] Future Use

[8] ON: When the system is armed in Stay mode, during the Exit delay, the system will sound 1 beep every 3 second.

OFF: When the system is armed in Stay mode, the system will be silent during the Exit delay.

Section [023] Tenth System Option Code

Option Description

[1] ON: the keypad [F] emergency key will only beep three times to acknowledge the button has been pressed. The system will not

activate the bell output. OFF: the system will activate the bell output and beep the keypad.

[2] Refer to the PC1616/PC1832/PC1864 Reference Manual for 200 Baud Open/Close Identifier details.

[3] ON: the system will only transmit the Test Transmission reporting code if the system is armed at the time the system is programmed

to report the event. OFF: the system will always report the Test Transmission reporting code at the programmed time.

[4] ON: the system changes the Test Transmission Reporting Cycle Time from Days to Hours. OFF: the Test Transmission Reporting

Cycle Time is in Days.

[5] ON: the user can switch from Away Arm mode to Stay Arm mode using the function keys. OFF: the user cannot switch arming

modes.

[6] ON: the system disconnects a listen in/two-way session if a new event occurs.

OFF: the system does NOT disconnect. New events are transmitted only after the session is terminated.

[7] ON: the system does NOT activate the keypad buzzer for any trouble condition. OFF: the system annunciates troubles via the

keypad buzzer (two beeps every 10 seconds) normally.

[8] For Future Use

Section [030] Fast Loop Response

This section is used to determine the Loop Response Time for the main panel zones.

ON: the loop response time will be 36 mS. OFF: the loop response time will be 400 mS.

Section [101] to [164] Zone Attributes

These sections are used to customize the operation of the zones. There are 9 toggle options in each Section:

Option Description

[1] ON: alarms are audible (bell output). OFF: alarms are silent.

[2] ON: the bell output is steady (burglary). OFF: the alarm output pulses (fire).

[3] ON: a zone violation or restoral will activate Chime. OFF: Chime is not activated.

Page 18

PowerSeries - PC1616/PC1832/PC1864

[4]

[5] ON: the partition can be armed even if the zone is violated (the zone will not affect the Ready status). OFF: the zone must be secure

[6] ON: the system shuts down alarm reporting after the programmed number of alarms have occurred. OFF: the panel will always

[7] ON: the system delays reporting the event for the time programmed for the Transmission Delay time. OFF: the panel immediately

[8] ON: the zone is either a wireless or addressable device. OFF: the zone is a hardwire zone (main panel, zone expander or keypad

[9] ON: the zone has the Cross Zone feature enabled. OFF: the zone functions normally.

ON: the user can manually bypass the zone using the [

before arming.

report the event if an alarm occurs.

transmits the reporting event when an alarm is detected.

zone).

When Zone Types (Section [001] to [004]) are programmed, the system will change the Zone Attributes to those found in the chart included in the Programming Worksheets. The Zone Attributes will default if a new Zone Type is programmed for a specific zone.

After programming the Zone Types, enter Section [101] to [164] and ensure that all options are programmed correctly.

Ready light ON: Program attributes [1-8]

Ready light and Armed light ON: Program attribute [9] (press [1] to turn option ON or OFF)

Press [9] to switch between attributes [1-8] and attribute [9].

][1] command. OFF: the zone cannot be manually bypassed.

Section [165] Maximum Dialing Attempts

Program the Maximum Dialing Attempts before the panel will generate a Failure to Communicate (FTC) trouble condition. Valid entries are [001] to [005]. For UL Listed installations, 5 attempts is required.

Section [166] Post Dial Wait for Handshake

Program the maximum time the panel will wait, after dialing, for a valid handshake from the central station. Valid entries are [001] to [255] seconds.

Section [167] T-Link Communications Wait for Acknowledgement

Program the maximum time the panel will wait, after sending a data packet, for an acknowledgement from the central station. Valid entries are [001] to [255] seconds.

Section [168] Daylight Savings Time (Move Clock Ahead)

Program the 3-digit Month (Data [001] to [012] represents January to December), the 3-digit Week (Data [000] represents day of the month, Data [001] to [005] represents weeks 1 to 5 of the month), the 3-digit Day (Data [001] to [031] represents day of the month if [000] was programmed in Day of the Month entry, IF [001] to [005] was programmed then Data [001] to [007] represents Sunday to Saturday), the 3-digit Hr to initiate the change (Data [000] or [023] represents the hour to make the change) and the Increment (Data [001] or [002] represents the number of hours to adjust).

Section [169] Standard Time (Set Clock Back)

Section [170] PGM Output Timer

Program the time, in seconds, PGM outputs programmed to follow the PGM Output Timer will activate for. Valid entries are [001] to [255].

Section [173] Bell Delay Timer

Program the time, in minutes, the panel will delay activating the bell output when an alarm occurs. If a TLM trouble condition is detected, the Bell Delay Timer will be aborted. Valid entries are [001] to [255].

Page 19

Section 4 – Programming Descriptions

Section [175] Auto-Arm Postpone Timer

Program the time, in minutes, that the system will postpone automatic arming. After the programmed time, the system will attempt to auto arm again. If data [000] is programmed, the system will instead abort the auto arm sequence. Valid entries are [001] to [255].

Section [176] Cross Zone/Police Code Timer

Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel will use to determine if a Cross Zone or Police Code event has occurred. If data [000] is programmed when using the Police Code feature, the panel will generate a Police Code event if any two zones go into alarm during any armed-to-armed period. Valid entries are [001] to [255].

Section [181] to [188] Auto-Arm Schedules

Program the time to auto arm (Section [181] for Partition 1, Section [182] for Partition 2 etc…) for each day of the week. Each Section has seven, 4-digit entries, two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the military format (for example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto arming.

Section [190] No Activity Arming Pre-Alert Duration

Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will provide a steady tone warning the user that the system will arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].

Section [191] to [198] No Activity Arm Timer

Program the time, in minutes, for the No Activity Arm Timer (Section [191] for Partition 1, Section [192] for Partition 2 etc…). If Delay Zones are restored and no zone activity is detected for the time programmed, the system will start the auto arm sequence. Valid entries are

[000] to [255].

Section [199] Auto-Arming Pre-Alert Timer

Program the time, in minutes, for the Auto-Arming Pre-Alert Time. This timer is used for all programmed auto-arming features (is not used for No Activity Arming). The keypads will provide a steady tone warning the user that the system will arm. The user can enter a valid access code to abort the arming sequence. Valid entries are [000] to [255].

Section [201] Partition Selection Mask

Turn the corresponding option ON to enable partitions [1] to [8]. ON (bit 1 cannot be turned OFF).

Section [202] to [265] Partition Zone Assignments

These Sections are used to assign zones to specific partitions (Section [202] to [209] for Partition 1, Sections [210] to [217] for Partition 2 etc.). Turn ON the option corresponding to the partition and zone to enable the zone on the specified partition. Turn the option OFF to dis- able the zone on the specified partition. Zones assigned to more than one partition are called ‘common zones’ and will only be armed if all the partitions the zone is assigned to are armed. Default = Zones 1-8 enabled on Partition 1.

Section [301] to [303] Telephone Numbers

Program the phone numbers as required. Phone Number 3 is dedicated as a back-up to Phone Number 1. HEX digits can be included for special applications:

HEX [A] Not used HEX [B] Simulates a [ HEX [C] Simulates a [#] key press HEX [D] Additional dial tone search HEX [E] 2-second pause HEX [F] End of phone number marker

] key press

Section [304] Call Waiting Cancel String

Program the digits required to disable call waiting. If enabled, the system will dial the programmed string on the first dialing attempt. Program unused digits with data [F].

Section [310] System Account Number

Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required, program the last two digits as data [FF]. If using the SIA format, this account number will be used for all reporting events. If using a different format, this account number will be used for all events that are not partition specific (for example, low battery, AC trouble etc.). For partition specific events the system will use the programmed Partition Account Number. For all formats other than SIA, program a HEX [A] for any digit [0] in the account number being used.

Page 20

PowerSeries - PC1616/PC1832/PC1864

Section [311] to [318] Partition Account Numbers

Program the Partition Account Number for each active partition (Section [311] for partition 1, Section [312] for partition 2 etc.). When using the Automatic SIA format, these account numbers are not used. The system will use the System Account Number for all reporting events. For all formats other than SIA, program a HEX [A] for any digit [0] in the account number being used.

Section [320] to [349] Reporting Codes

Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt to report an event if data [00] or data [FF] is programmed for the reporting code.

Section [350] Communicator Format

Program the 2-digit number for the desired Communicator Format for the First Phone Number and Second Phone Number. When dialing the Third Phone Number, the system will use the Communicator Format programmed for Phone Number 1. Valid entries are [01] to [13]. Refer to the Programming Worksheet for a list of the available Communicator Formats. Refer to the PC1616/PC1832/PC1864 Reference Manual for Communicator Format details.

Section [351] to [376] Communicator Call Direction Options

Reporting events are categorized into 5 groups; Alarm/Restore, Opening/Closing, Tamper Alarm/Restore, System Maintenance and Test Transmissions. Program which Phone Number the control panel will use to transmit reporting events by turning the option ON in the correct Section. Phone Number 1 and/or Phone Number 2 can be used.

Section [377] Communicator Variables

Program a 3-digit number for each program entry:

Swinger Shutdown (Alarms): Maximum number of alarm/restoral transmissions per zone. Valid entries: [001] to [014]. Program data [000] to disable shutdown.

Swinger Shutdown (Tamper): Maximum number of tamper alarm/restoral transmissions per zone. Valid entries: [000] to [014]. Program data [000] to disable shutdown.

Swinger Shutdown (Trouble): Maximum number of trouble alarm/restoral transmissions per trouble condition. Valid entries: [000] to [014]. Program data [000] to disable shutdown.

Communicator (Transmission) Delay: Time, in seconds, panel will delay reporting an alarm event. Valid entries: [000] to [255].

AC Failure Communication Delay: Time, in minutes, panel will delay reporting an AC trouble event. Valid entries: [000] to [255].

TLM Trouble Delay: Time, in 3 second checks, before the system will consider the phone line disconnected. Valid entries: [002] to [255]

(e.g., 3 x10 seconds = 30 seconds).

TLM Restoral follows the same delay.

Test Transmission Cycle (Land Line): Number of days between test transmission reporting events. Valid entries: [001] to [255].

For Future Use

Wireless Zone Low Battery Delay: Number of days the system will delay reporting a wireless low battery to the central station. Valid entries: [000] to [255]. Program data [000] for no delay.

Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel will delay before transmitting the event to the central station. Valid entries: [001] to [255].

Communication Cancel Window: Time, in seconds, after an alarm has occurred that the system will report a Communication Cancel reporting event

if the system is disarmed. They keypad will beep rapidly to indicate the Communication Cancel reporting event has been communicated successfully. Valid entries: [001] to [255].

Section [378] Test Transmission Time

Program the time the system will report a Test Transmission reporting event. Program 4 digits – [HH][MM] using military standard. For a test transmission at 11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59].

Page 21

Section 4 – Programming Descriptions

Section [380] First Communicator Option Code

Option Description

[1] ON: the system communicator is enabled. OFF: the communicator is disabled.

[2] ON: the system transmits alarm restorals if the zone is restored and the bell has timed out. OFF: the system transmits alarm restorals

immediately when the zone is restored.

[3] ON: the panel uses rotary (pulse) dialing. OFF: the panel uses touchtone (DTMF) dialing

[4] ON: the panel will switch from touchtone dialing to rotary dialing after the 4th failed attempt to communicate.

OFF: the panel will use rotary dialing for all dialing attempts.

[5] ON: the system uses the Third Phone Number to back up the First Phone Number. OFF: the Third Phone Number is disabled.

[6] ON: the system alternates between the First Phone Number and Third Phone Number when attempting to report an event.

OFF: the panel will dial the First Phone Number for the programmed number of attempts, then switch to the Third Phone Number.

[7] For future Use

[8] ON: the Delinquency feature follows zone activity. OFF: the Delinquency feature follows arming.

Section [381] Second Communicator Option Code

Option Description

[1] ON: the keypad beeps 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the keypad does not beep.

[2] ON: the bell output squawks 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the bell output does

not activate.

[3] ON: the system uses programmed reporting codes when transmitting using the SIA format.

OFF: the system automatically generates all reporting codes transmitted.

[4] ON: the system beeps the keypad 8 times after successfully transmitting a Closing reporting event. OFF: the keypad does not beep.

[5] ON: the system requests a Listen in/Two-way session the next time it calls the 1st/3rd Phone Number when the PC59xx transmits a

request. OFF: the system ignores the request from the PC59xx.

This Option is used with PC59xx series modules.

[6] ON: the system requests a Listen in/Two-way session the next time it calls the 2nd Phone Number when the PC59xx transmits a request.

OFF: the system will ignore the request from the PC59xx.

This Option is used with PC59xx series modules.

[7] ON: the system uses Contact ID format programmed reporting codes when transmitting reporting codes.

OFF: the system automatically generates all reporting codes transmitted.

[8] For Future Use

Section [382] Third Communicator Option Code

Option Description

[1] ON: the system will use the digit [5] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.

OFF: the system will use the digit [4] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.

[2] ON: the system will transmit all alarms during Walk Test. OFF: the system will not report alarm events during Walk Test.

[3] ON: the keypad will display the message ‘Communications Cancelled’ (programmable LCD) or ‘CC’ (fixed-message LCD) upon

successful transmission of the Communication Cancelled reporting event. OFF: the keypad will not display these messages.

[4] ON: the system dials the Call Waiting Cancel String on the first attempt to dial the central station. OFF: the system does not dial the Call

Waiting Cancel String.

[5] ON: enables support for the T-Link module. OFF: disables T-Link.

Page 22

PowerSeries - PC1616/PC1832/PC1864

[6] ON: the AC Failure Transmission Delay Timer will use hours. OFF: the delay will be in minutes.

[7-8] For Future Use

Section [401] First Downloading Option Code

Option Description

[1] ON: the system answers incoming calls for downloading (either Programmed Number of Rings or Double Call). OFF: the system does not

answer incoming calls for downloading.

These settings do not affect the 6 hour DLS downloading window on power up.

[2] ON: the user can enable downloading for the DLS Window using the [][6] command. OFF: the user cannot enable downloading.

[3] ON: the system will hang up after a successful DLS connection and call the computer back using the DLS Phone Number ( Section [402]).

OFF: the system stays connected to the computer.

[4] ON: the user can initiate a downloading session using the [][6] command. OFF: the user cannot initiate a downloading session.

[5] ON: the system attempts to call the downloading computer after transmitting a Event Buffer 75% Full event to the central station. OFF: the

system does NOT call the downloading computer after transmitting this event.

[6]-[8] For Future Use

Section [402] Downloading Computer Phone Number

The Downloading Computer Telephone Number is used for Call Back, User Initiated DLS and the Auto Event Buffer Upload functions. Program the phone number as required. HEX digits can be included for special applications:

HEX [A] Not used HEX [B] Simulates a [ HEX [C] Simulates a [#] key press HEX [D] Additional dial tone search HEX [E] 2-second pause HEX [F] End of phone number marker

] key press

Section [403] Downloading Access Code

Program the 6-digit Downloading Access Code. Upon connection, the system will only connect to the downloading computer if the Downloading Access Code programmed matches the Downloading Access Code programmed in the computer file.

Section [404] Panel Identification Code

Program the 6-digit Panel Identification Code. This code is used by the downloading computer to verify the correct account is calling back (Call Back feature) or to identify which customer account file should be used (User Initiated DLS and Auto Event Buffer Upload features).

Section [405] Double-Call Timer

Program the maximum time, in seconds, between calls when connecting to panel using the double call feature. Valid entries are [000] to [255].

Section [406] Number of Rings to Answer On

Program the number of consecutive rings that panel must detect to answer for downloading. Valid entries are [000] to [010].

Section [499] PC-Link Communications

Enter the following command to initiate downloading via PC-Link – Section [499] [Installer Code] [499].

Section [501] to [514] Programmable Output Attributes

These Sections are used to customize the operation of the PGM outputs (Section [501] for PGM 1, Section [502] for PGM 2 etc.). The avail- able options depend on which PGM output type is programmed.

When the PGM Output Options (Section [009] to [011]) are programmed, the system will change the PGM Attributes to the default settings. The PGM Attributes will default if a new PGM output option is programmed.

Page 23

Section 4 – Programming Descriptions

PGM Output Option [01], [03] to [08], [11] to [22], [25]

Option Description

[3] ON: the PGM output will operate normally (switch to ground when activated). OFF: the PGM output will be normally ground and switch

to open collector (open circuit) when activated.

PGM Output Option [19] to [22]

Option Description

[4] ON: the PGM output will activate for the duration of the PGM Output Timer when the [][7][x] command is performed.

OFF: the PGM output will latch until the [][7][x] command is performed again.

[5] ON: a valid user code must be entered after the [][7][x] command. OFF: user code is not required.

PGM Output Option [09]

Option Description

[1] ON: PGM output activates if a Service Required trouble condition is present.

[2] ON: PGM output activates if an AC trouble condition is present.

[3] ON: PGM output activates if a Telephone Line trouble condition is present.

[4] ON: PGM output activates if a Failure to Communicate trouble condition is present.

[5] ON: PGM output activates if a Zone Fault condition is present.

[6] ON: PGM output activates if a Zone Tamper condition is present.

[7] ON: PGM output will activates if a Wireless Low Battery trouble condition is present.

[8] ON: PGM output will activates if a Loss of Clock trouble condition is present.

PGM Output Option [10]

Option Description

[1] ON: PGM output activates if a Burglary Alarm occurs.

[2] ON: PGM output activates if a Fire Alarm occurs.

[3] ON: PGM output activates if a Panic Alarm occurs.

[4] ON: PGM output activates if a Medical Alarm occurs.

[5] ON: PGM output activates if a Supervisory Alarm occurs.

[6] ON: PGM output activates if a Priority Alarm occurs.

[7] ON: PGM output will activates if a 24-Hour Hold-Up Alarm occurs.

[8] ON: the PGM output activates for the time programmed for the PGM Output Timer. OFF: the PGM output will latch until a valid user

code is entered.

If System Event PGM is programmed to follow the command output timer then all attributes must be enabled.

Section [551] to [564] PGM Partition Assignment

These sections are used to customize the operation of the PGM outputs (Section [551] for PGM 1, Section [552] for PGM 2 etc.). Turn on the correct option in the correct section to assign the PGM output to a specified partition. PGM outputs can be assigned to more than one partition. For PGM outputs that are considered ‘system’ outputs (e.g.,Trouble output), programming in these sections will not affect the operation of the PGM output.

Section [700] Automatic Clock Adjust

Program the number of seconds for the last minute of the day. This can be used to make minor corrections to the clock if the AC frequency is not reliable. Valid entries are [01] to [99].

Page 24

PowerSeries - PC1616/PC1832/PC1864

Section [701] First International Option Code

Option Description

[1] ON: configures the system for 50Hz AC. OFF: configures the system for 60Hz AC.

[2] ON: the system uses the internal crystal for the internal panel clock. OFF: the system uses the AC frequency for the internal panel clock.

[3] ON: the system will inhibit arming if a Low Battery or AC trouble condition is present. OFF: arming will not be inhibited.

[4] ON: all Tamper troubles will latch and arming will be inhibited. Enter Installer Programming to clear the trouble condition and return to

normal operation. OFF: tamper troubles will not latch and will not inhibit arming.

[5] ON: all access codes are 6 digits long. OFF: all access codes are 4 digits long.

[6] ON: the system will hang up if a busy tone is detected. This attempt is not counted towards the Maximum Dialing Attempts programmed.

OFF: the panel will not detect busy tones.

[7] ON: the system will charge the battery at approximately 700mA. OFF: the system will charge the battery at 400mA.

[8] ON: the system will abort a DLS session, Escort access, Listen In/Two-way session if a new central station communication event occurs.

OFF: non-critical events (Test transmission, Periodic Test and System Test) will not abort the session. Events will be communicated after

the session is complete.

Section [702] Second International Option Code

Option Description

[1] ON: the communicator uses 33/67 make/break ratio when pulse dialing. OFF: the system uses 40/60 make/break ratio.

[2] ON: the system dials regardless of the presence of dial tone after the first attempt. OFF: the system dials only if dial tone is detected.

[3] ON: changes the Test Transmission Cycle Time to minutes. OFF: sends a Test Transmission after the programmed number of days.

[4] ON: the system accepts 1600Hz handshake pulse formats. OFF: the system accepts 1400Hz or 2300Hz handshakes.

[5] ON: the system generates a tone for 500mS every 2 seconds indicating digital equipment is making the call vs. a voice call.

OFF: the system does not generate a tone.

[6] ON: the tone generated (2100Hz.) indicates that digital equipment is making the call. OFF: the tone is 1300Hz.

[7] ON: the DLS dowloading window is 1 hour. OFF: the DLS downloading window is 6 hours.

[8] ON: the system activates the bell output if a Failure to Communicate trouble occurs while the system is armed.

OFF: the system does NOT activate the bell output if a Failure to Communicate trouble occurs while the system is armed.

Section [703] Delay Between Dialing Attempts

Program the time the panel will wait between dialing attempts to transmit a reporting event to the central station. Valid entries are [001] to [255].

Section [800]-[851] Module Programming

The following program sections are used to program different modules that can be connected to the control panel. Refer to the respective Installation Manual for installation and programming information

Section [801]: PC5400 Printer Module Programming Section [802]: PC59xx VOX Module Programming Section [803]: Alternate Communicator Programming Section [804]: Wireless Programming Section [805]: PC5100 Addressable Programming Section [851]: T-Link Programming

Page 25

Section 4 – Programming Descriptions

Section [900] Special Installer Instructions

Section [900]: Display Panel Version

Only available with LCD5500 or PK5500 keypads. The system will display the version of the control panel (for example, [0410] indicates panel version 4.10).

Section [901]: Installer Walk Test

The system will turn Installer Walk Test ON. The Ready, Armed and Trouble LED’s will flash rapidly while the test is active. Every time a zone is violated the system will activate the bell output for two seconds and log the event to the event buffer. To turn Installer Walk TestOFF enter Section [901] again. The system automatically terminates the test of there is no zone activity for 15 minutes.

Section [902]: Module Supervision Reset

All modules are automatically detected within one minute after being connected to the Keybus. Enter Section [902] to clear detected modules if a module is removed, if PC5108 jumpers are changed, or if a keypads slot assignments are programmed. The system will rescan the Keybus to determine which modules are connected.

Section [903]: View Module Supervision

The keypad will display the modules detected by the system by turning on the associated zone light (LED keypads), flashing the numbers (fixed-message LCD keypads) or displaying the modules detected in plain language (programmable LCD keypads). Refer to the chart below:

Indicator Light

(Zone)

[01] to [08] [09] to [14]

[15] [16] [17] [18] [19] [20] [21] [22] [24]

[26] to [29]

Keypad in Slot #1 to #8 PC5108 Zone Expander #1 to #6 PC5100 Module PC5108 Zone Expander #7 PC5132 Module or RFK keypad with integrated wireless receiver PC5208 PC5204 Module PC5400 Module PC59xx Module Alternate Communicator Escort5580 or Escort5580TC PC5200 #1 to #4

Module

Section [904]: Wireless Placement Test

Enter Section [904] followed by the 2-digit number of the wireless zone to test. When a wireless signal is received from the selected trans- mitter, the system will indicate the location as Good or Bad as follows:

Good: One bell squawk, 1 keypad beep, keypad zone light [1] ON Bad: Three bell squawks, 3 keypad beeps, keypad zone light [3] ON

Press [#] to exit when testing is complete. Enter the 2-digit zone number for the next wireless device to test or press [#] to return to standard programming.

Section [990]: Installer Lockout Enable

Enter Section [990][Installer Code][990] to enable the Installer Lockout feature. A hardware default cannot be performed when the Installer Lockout feature is ON. In addition, the system will chatter the line seizure relay 10 times if the panel is powered up to indicate the feature is ON.

Section [991]: Installer Lockout Disable

Enter Section [991][Installer Code][991] to turn the Installer Lockout feature OFF.

Page 26

PowerSeries - PC1616/PC1832/PC1864

Section [993] to [999]: Factory Default Module/Panel

The following Sections can be used to factory default a module or the main control panel. Enter the appropriate Section, followed by the Installer Code, followed by the Section number (E.g., [993][Installer Code][993])

Section [993]: Factory Default Alternate Communicator Section [995]: Factory Default Escort5580 Module Section [996]: Factory Default Wireless Receiver Section [997]: Factory Default PC5400 Module Section [998]: Factory Default PC59xx Module Section [999]: Factory Default Main Control Panel

Hardware Reset (Default) Main Control Panel

Perform the following to default the main control panel:

1. Power down the system completely.

2. Connect a short between Zone 1 and PGM1 on the control panel (remove all other wires form these terminals).

3. Power up the control panel (AC power only) for 10 full seconds.

4. Power down the control panel, remove short between Zone 1 and PGM1.

5. Power up the control panel.

Page 27

Section 5: Programming Work Sheets

5.1 Index to Programming Work Sheets

Section 5: Programming Work Sheets

Programming Option Page

[000] Keypad Enrollment.....................................................................26

[001]-[004] Zone Definitions................................................................26

[005] System Times.............................................................................27

[006] Installer’s Code...........................................................................28

[007] Master Code...............................................................................28

[008] Maintenance Code.....................................................................28

[009] PGM 1&2 Output Programming (Main Panel)............................28

[010] PGM 3-10 Output Programming (Main Panel/PC5208) .............28

[011] PGM 11-14 Output Programming (PC5204) .............................28

[012] Keypad Lockout Options ............................................................28

[013] 1st System Options....................................................................29

[014] 2nd System Options...................................................................29

[015] 3rd System Options....................................................................29

[016] 4th System Options....................................................................29

[017] 5th System Options....................................................................30

[018] 6th System Options....................................................................30

[019] 7th System Options....................................................................30

[020] Keypad Zone Assignments ........................................................30

[021] 8th System Options....................................................................30

[022] 9th System Options....................................................................30

[023] 10th System Options..................................................................31

[030] Zone Loop Response (Zones 1-8) .............................................31

[101] - [164] Zone Attributes ...............................................................32

[165] Maximum Dialing Attempts to Each Telephone Number............34

[166] Post Dial Wait for Handshake (All Formats) ..............................34

[167] T-LINK Interface Communications Wait for Acknowledge ..........34

[168] Set Clock Forward (Daylight Saving Time).................................34

[169] Set Clock Back (Standard Time)................................................34

[170] PGM Output Timer .....................................................................34

[175] Auto-arm Postpone Timer ..........................................................34

[176] Cross Zone/Police Code Timer .................................................34

[181]-[188] Automatic Arming Schedule .............................................34

[190] No Activity Arming Pre-Alert Time..............................................34

[191]-[198] No Activity Arming Timers ................................................35

[199] Auto-arming Pre-Alert Timer .....................................................35

[201] Partition Selection Mask.............................................................35

[301] 1st Telephone Number (32 Digits)..............................................36

[302] 2nd Telephone Number (32 Digits).............................................36

[303] 3rd Telephone Number (32 Digits) .............................................36

[304] Call Waiting Cancel String (6 Digits) ..........................................36

[310] System Account Code................................................................36

[311]-[318] Partition 1-8 Account Numbers.........................................36

[320]-[323] Alarm Reporting Codes, Zones 01-64 ..............................36

[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64................37

[328] Miscellaneous Alarm Reporting Codes ......................................37

[329] Priority Alarm and Restoral 37

[330]-[333] Tamper Reporting Codes, Zones 01-64............................37

[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64 .............38

[338] Miscellaneous Tamper Reporting Codes ...................................38

[339]-[340] Closing (Arming) Reporting Codes,

Access Codes 1-32.....................................................................38

[341] Miscellaneous Closing (Arming) Reporting Codes.....................38

[342]-[343] Opening (Disarming) Reporting Codes,

Access Codes 1-32.....................................................................38

[344] Miscellaneous Opening (Disarming) Reporting Codes..............39

Programming Option Page

[345] Maintenance Alarm Reporting Codes........................................39

[346] Maintenance Restoral Reporting Codes ..................................39

[347] Miscellaneous Maintenance Reporting Codes ..........................39

[348] Test Transmission Reporting Codes .........................................39

[349] PC5700 Maintenance Reporting Codes ................................... 39

[350] Communicator Format Options .................................................39

[351]-[358] Alarm/Restore Communicator Call Directions..................40

[359]-[366] Tamper/Restore Communicator Call Directions ...............40

[367]-[374] Opening/Closing Communicator Call Directions.............. 40

[375] System Maintenance Communicator Call Directions ................40

[376] System Test Transmissions Communicator Call Directions.......40

[377] Communication Variables..........................................................41

[378] Test Transmission Time of Day .................................................41

[380] 1st Communicator Options ........................................................41

[381] 2nd Communicator Options....................................................... 41

[382] 3rd Communicator Options........................................................42

[401] DLS Downloading Option Codes ...............................................42

[402] DLS Downloading Telephone Number (32 Digits) ..................... 42

[403]-[404] DLS Downloading Access Code / Panel ID Code ...........42

[405] Answering Machine Double Call Timer......................................42

[406] Number of Rings to Answer On................................................. 42

[499] Initiate PC-Link Downloading.....................................................42

[501]-[502] PGM 1&2 Output Attributes (Main Panel).........................43

[503]-[504] PGM 3&4 Output Attributes (Main Panel / PC5208).........48

[505]-[510] PGM 5-10 Output Attributes (5208)..................................48

[511]-[515] PGM 11-14 Output Attributes (5204)................................48

[551]-[552] PGM 1&2 Output Partition Assignment (Main Panel........48

[553]-[554] PGM 3&4 Output Partition Assignment

(Main Panel / PC5208)...............................................................48

[555]-[560] PGM 5-10 Output Partition Assignment (5208)................48

[561]-[564] PGM 11-14 Output Partition Assignment (5204)..............48

[700] Automatic Clock Adjust .............................................................45

[701] 1st International Options............................................................45

[702] 2nd International Options...........................................................45

[703] Delay between Dialing Attempts................................................45

[801] PC5400 Printer Module Programming.......................................45

[802] PC59xx VOX Programming........................................................45

[803] Alternate Communicator Programming...................................... 45

[804] PC5132 Wireless Expansion Programming...............................45

[805] PC5100 Programming ...............................................................45

[851] T-LINK Programming..................................................................45

[900] Panel Version Displayed ............................................................46

[901] Installer Walk Test Mode Enable/Disable ..................................46

[902] Module Supervision Reset .......................................................46

[903] Module Supervision Field ........................................................46

[904] Wireless Module Placement Test .............................................46

[990] Installer Lockout Enable.............................................................46

[991] Installer Lockout Disable............................................................46

[993] Restore Alternate Communicator to Default Programming........ 46

[995] Restore Escort5580 to Default Programming ............................46

[996] Restore PC5132 to Default Programming..................................46

[997] Restore PC5400 to Default Programming..................................46

[998] Restore PC59xx to Default Programming..................................46

[999] Restore Control Panel to Default Programming......................... 46

Page 28

PowerSeries - PC1616/PC1832/PC1864

5.2 Programming Worksheets

Shaded programming sections indicate minimum programming trerquirements

SIA FAR CP-01 defaults are indicated in gray text.

Keypad Partition /Slot and Function Key Programming

[000] Keypad Enrollment

This must be done at each keypad requiring programming.

[0] Slot address [Valid entries are 0-8 for the partition, 1-8 for the slot. (e.g., to enroll a keypad in partition 3 and slot 1, enter (31)]

[1] Function Key 1 Assignment (Valid entries are 00-32)

[2] Function Key 2 Assignment (Valid entries are 00-32)

[3] Function Key 3 Assignment (Valid entries are 00-32)

[4] Function Key 4 Assignment (Valid entries are 00-32)

[5] Function Key 5 Assignment (Valid entries are 00-32)

Function Key Options:

00 Not used 11 [*][5] Access Code Programming 22 For Future Use 01 Select Partition 1 12 [*][6] User Functions 23 Bypass Recall 02 Select Partition 2 13 Command Output #1 [*][7][1] 24 Recall Bypass Group 03 Stay Arm 14 Command Output #2 [*][7][2]/Sensor Reset 25 For Future Use 04 Away Arm 15 For Future Use 26 Time and Date 05 [*][9] No-Entry Arm 16 [*][0] Quick Exit 27 Select Partition 3 06 [*][4] Chime On / Off 17 [*][1] Reactivate Stay/Away Zones 28 Select Partition 4 07 [*][6][——][4] System Test 18 For Future Use 29 Select Partition 5 08 [*][1] Bypass Mode 19 Command Output 3 [*][7][3] 30 Select Partition 6 09 [*][2] Trouble Display 20 For Future Use 31 Select Partition 7 10 [*][3] Alarm Memory 21 Command Output 4 [*][7][4] 32 Select Partition 8

[20] Zone Assigned

00 00 00 00 00 00 00 00

Key 1 Key 2 Key 3 Key 4 Key 5

ICON / LED Defaults Full Message Defaults KEYPAD 1 KEYPAD 2 KEYPAD 3 KEYPAD 4 KEYPAD 5 KEYPAD 6 KEYPAD 7 KEYPAD 8

Partition/

Slot

11 00 03 04 06 14 08 18 00 03 04 06 14 16

[001]-[004] Zone Definitions

00 Null Zone (Not Used) 12 24 Hour Holdup* 25 Interior Delay* 01 Delay 1* 13 24 Hour Gas* 26 24 Hour Non-alarm* 02 Delay 2* 14 24 Hour Heating* 29 Auto Verified Fire 03 Instant* 15 24 Hour Auxiliary* 30 Fire Supervisory 04 Interior* 16 24 Hour Panic* 31 Day Zone* 05 Interior, Stay/Away* 17 24 Hour Emergency* 32 Instant Stay/Away* 06 Delay, Stay/Away* 18 24 Hour Sprinkler* 35 24-hour Bell/Buzzer 07 Delayed 24 Hour Fire (Hardwired)** 19 24 Hour Water* 37 Night Zone 08 Standard 24 Hour Fire (Hardwired) 20 24 Hour Freeze* 87 Delay 24 Hour Fire (Wireless)** 09 24 Hour Supervisory 21 24 Hour Latching Tamper* 88 Standard 24 Hour Fire (Wireless)** 10 24 Hour Supervisory Buzzer* 22 Momentary Keyswitch Arm* 11 24 Hour Burglary* 23 Maintained Keyswitch Arm*

*For burglary applications only ** For residential fire applications only

Page 29

5.2 Programming Worksheets

Section Zone Def. Section Zone Def. Section Zone Def. Section Zone Def.

[001]

01 01

02 03

03 03

04 03

05 04

06 04

07 04

08 04

09 00

10 00

11 00

12 00

13 00

14 00

15 00

16 00

I_____I_____I

[002]

17 00

18 00

19 00

20 00

21 00

22 00

23 00

24 00

25 00

26 00

27 00

28 00

29 00

30 00

31 00

32 00

I_____I_____I

[003]

33 00

34 00

35 00

36 00

37 00

38 00

39 00

40 00

41 00

42 00

43 00

44 00

45 00

46 00

47 00

48 00

I_____I_____I

[004]

49 00

50 00

51 00

52 00

53 00

54 00

55 00

56 00

57 00

58 00

59 00

60 00

61 00

62 00

63 00

64 00

[005] System Times

Valid entries for Entry Delay is between 030-255, valid entries for Exit Delay is between 045-255 for SIA CP-01.

[01] Partition 1 Entry/Exit times [05] Partition 5 Entry/Exit times

030 045 120

I___I___I___I Entry Delay 1

I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

030 045 120

I___I___I___I Entry Delay 1 I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

I_____I_____I

[02] Partition 2 Entry/Exit times [06] Partition 6 Entry/Exit times

030 045 120

I___I___I___I Entry Delay 1

I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

030 045 120

I___I___I___I Entry Delay 1 I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

[03] Partition 3 Entry/Exit times [07] Partition 7 Entry/Exit times

030 045 120

I___I___I___I Entry Delay 1

I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

030 045 120

I___I___I___I Entry Delay 1 I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

[04] Partition 4 Entry/Exit times [08] Partition 8 Entry/Exit times

030 045 120

I___I___I___I Entry Delay 1

I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

030 045 120

I___I___I___I Entry Delay 1 I_0_I_3_I_0_I Entry Delay 2 I_0_I_6_I_0_I Exit Delay

[09] Bell Cut-Off Timer (All Partitions)

004

I___I___I___I Enter 3 digits from 001-255

For SIA CP-01 compliant installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds). If the Exit

Delay is silent (Section 14, Option 6 or Stay Function Key Arming) the exit delay must be twice the programmed value but must not exceed 255 seconds (i.e., 090-255 seconds).

For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.

Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.

Page 30

PowerSeries - PC1616/PC1832/PC1864

[006] Installer’s Code [007] Master Code [008] Maintenance Code

Default Default Default

5555 I_______I_______I_______I_______I 1234 I_______I_______I_______I_______I AAAA I_______I_______I_______I_______I

Programmable Output Options

01 Residential Burglary and Fire Bell Output 15 Remote Operation (DLS-3 Support) 02 For Future Use 16 For Future Use 03 Sensor Reset [*][7][2] 17 Away Armed Status 04 2 Wire Smoke Support (PGM 2 only) 18 Stay Armed Status 05 System Armed Status 19 Command Output #1 ([*][7][1]) 06 Ready To Arm 20 Command Output #2 ([*][7][2]) 07 Keypad Buzzer Follow Mode 21 Command Output #3 ([*][7][3]) 08 Courtesy Pulse 22 Command Output #4 ([*][7][4]) 09 System Trouble Output (with Trouble options) 23 24 Hour Silent Input 10 System Event [Strobe (with Event options)] 24 24 Hour Audible Input 11 System Tamper (all sources: zones, keypad, modules) 25 Delayed Fire and Burglary Output 12 TLM and Alarm 29 Zone Follower Output 13 Kissoff Output 30 Partition Status Alarm Memory 14 Ground Start Pulse

Output types [03] and [20] cannot be used together on the same system.

[009] PGM1 and PGM2 Output Programming (Main Panel)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

Default Default

I_______I_______I PGM 1 10 I_______I_______I PGM 2

[010] PGM3 to PGM10 Output Programming (Main Panel/PC5208)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

Default Default

I_______I_______I PGM 3 (main panel/PC5208)* 01 I_______I_______I PGM 7 (PC5208)

01 I_______I_______I PGM 4 (main panel/PC5208)* 01 I_______I_______I PGM 8 (PC5208) 01 I_______I_______I PGM 5 (PC5208) 01 I_______I_______I PGM 9 (PC5208) 01 I_______I_______I PGM 6 (PC5208) 01 I_______I_______I PGM 10 (PC5208)

These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4 will work the same as the second PC5208 output.

[011] PGM 11 to PGM 14 Output Programming (PC5204)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

Default Default

I_______I_______I PGM 11 01 I_______I_______I PGM 13

01 I_______I_______I PGM 12 01 I_______I_______I PGM 14

Other System Options

[012] Keypad Lockout Options

If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.

Default

000

000 I_______I_______I_______I Lockout Duration (001-255 minutes)

I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes)

Page 31

DSC PowerSeries Alarm System User Guide

About Your Security System

Your DSC Security System has been designed to provide you with the greatest possible flexibility and convenience. Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be equally instructed in its use. Fill out the “System Information” page with all of your zone information and access codes and store this manual in a safe place for future reference.

The PowerSeries security system includes specific false alarm reduction fea-

tures and is classified with ANSI / SIA CP-01-2000. To comply with this specification, your installation must have a minimum of two keypads. Consult your installer for further information regarding the false alarm reduction features built into your system as all are not covered in this manual.

Fire Detection

This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning if a fire condition is detected. Good fire detection depends on having adequate number of detectors placed in appropriate locations. This equipment should be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincey MA 02269). Carefully review the Family Escape Planning guidelines in this manual

Your installer must enable the fire detection portion of this equipment before it becomes functional.

Test ing

To insure that your system continues to function as intended, you must test your system weekly. Please refer to the “Testing your System” section in this manual. If your system does not function properly, call your installing company for service.

Monitoring

This system is capable of transmitting alarms, troubles & emergency information over telephone lines to a central station. If you initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.

The monitoring function must be enabled by the installer before it becomes functional

SIA There is a communicator delay of 30 seconds in this control panel. It can

be removed, or it can be increased up to 45 seconds, at the option of the enduser by consulting with the installer.

Maintenance

With normal use, the system requires minimum maintenance. Note the following points:

• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth should remove normal accumulations of dust.

• Use the system test described in “Testing Your System” to check the battery condition. We recommend, however, that the standby batteries be replaced every 3-5 years.

• For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion detectors or glassbreak detectors, consult the manufacturer’s literature for testing and maintenance instructions.

General System Operation

Your security system is made up of a DSC control panel, one or more keypads and various sensors and detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The metal cabinet contains the system electronics, fuses and standby battery.

Only the installer or service professional should have access to the control panel.

All the keypads have an audible indicator and command entry keys. The LED keypads have a group of zone and system status lights. The LCD keypad has an alphanumeric liquid crystal display (LCD). The keypad is used to send commands to the system and to display the current system status. The keypad(s) will be mounted in a convenient location inside the protected premises close to the entry/exit door(s). The security system has several zones of area protection and each of these zones will be connected to one or more sensors (motion detectors, glassbreak detectors, door contacts, etc.). A sensor in alarm will be indicated by the corresponding zone lights flashing on a LED keypad or by written messages on the LCD keypad. Additional features of the PC1616/PC1832/PC1864 Security System are an Automatic Inhibit (Swinger Shutdown) for Alarm, Tamper and Trouble signals after 3 occurrences in a given set period (see Section 5.6 Option [377] in the Installation Manual). There is also a Programmable Keypad Lockout option (see Section 5.3 Option [012] in the Installation Manual).

A security system cannot prevent emergencies. It is only intended to alert you and – if included – your central station of an emergency situation. Security systems are generally very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system should be installed and serviced by qualified security professionals who should instruct you on the level of protection that has been provided and on system operations.

IMPORTANT NOTICE

Keypad Display Symbols

LCD5501 Fixed Message

810

PK5501

11 10

LED5511

1 Clock Digits 1, 2 – These two 7 segment clock digits indicate the hour digits

when the local clock is active, and identify the zone when the OPEN or ALARM icons are active. These two digits scroll one zone per second from the lowest zone number to the highest when scrolling through zones.

2 : (Colon) – This icon is the hours/minutes divider and will flash once a

second when the local clock is active.

3 Clock Digits 3, 4 – These two 7 segment displays are the minute digits when the

local clock is active.

4 1 to 8 – These numbers identify troubles when [4][2] is pressed.

5 Memory – Indicates that there are alarms in memory.

6 Bypass – Indicates that there are zones automatically or manually bypassed.

7 Program – indicates that the system is in Installer’s Programming, or the key-

pad is busy.

8 Awa y – Indicates that the panel is armed in the Away Mode. It will turn on at the

beginning of the Exit Delay.

9 Fire – Indicates that there are fire alarms in memory.

10 Stay – Indicates that the panel is armed in the Stay Mode. It will turn on at the

beginning of the Exit Delay.

11 Chime – This icon turns on when the Chime

Door Chime on the system. It will turn off when the chime function key is pressed again to disable Door Chime.

12 AM, PM – This icon indicates that the local clock is displaying 12 Hr. time.

These icons will not be on if the system is programmed for 24 Hr. time.

13 ALARM – This icon is used with clock digits 1 and 2 to indicate zones in alarm

on the system. When a zone is in alarm, the ALARM icon will turn on, and 7 segment displays 1 and 2 will scroll through the zones in alarm.

14 OPEN – This icon is used with clock digits 1 and 2 to indicate violated zones

(not alarm) on the system. When zones are opened, the OPEN icon will turn on, and 7 segment displays 1 and 2 will scroll through the violated zones.

15 AC – Indicates that AC is present at the main panel.

16 System Trouble – Indicates that a system trouble is active.

17 Night – Indicates that the panel is armed in the Night Mode.

18 System – Indicates one or more of the following:

Memory – Indicates that there are alarms in memory. Bypass – Indicates that there are zones automatically or manually bypassed. System Trouble – This icon is displayed when a system trouble is active.

19 Ready Light (green) – If the Ready light is on, the system is ready for

arming.

20 Armed Light (red) – If the Armed light is on, the system has been armed

successfully.

LCD5501 ICON

LCD5511

PK5508/PK5516

function key is pressed to enable

PK5500 Language Selection

Your keypad may be able to display messages in different languages.

1. Press and hold both keys simultaneously.

2. Using the keys, scroll through the available languages.

3. Press to select your desired language.

Page 32

Download complete User manual from www.dsc.com

Emergency Keys

Press the (F), (A) or (P) key for 2 seconds to generate a Fire, Auxiliary or Panic alarm. The keypad sounder will beep indicating that the alarm input has been accepted and transmission to the central station is underway. Ask your alarm company if the emergency keys are available on your system

Fire Keys can be disabled by the Installer.

LED5511/LCD5511 Keypad

Press and Hold both keys simultaneously for 2 seconds to send the following messages:

Fire message, Auxiliary message, Panic Message.

When Alarm Sounds

The system can generate 2 different alarm sounds:

• Continuous Siren = Intrusion (Burglary Alarm)

• Temporal / Pulsed Siren = Fire Alarm

Intrusion (Burglar) Alarm Continuous Siren

If you are unsure of the source of the alarm approach with caution ! If the alarm was accidental, enter your Access Code to silence the alarm. Call your central station to avoid a dispatch.

Fire Alarm Pulsed Siren

Follow your emergency evacuation plan immediately!

If the fire alarm was accidental (i.e. burned toast, bathroom steam, etc.), enter your Access Code to silence the alarm. Call your central station to avoid a dispatch. Ask your alarm company if your system has been equipped with fire detection. To reset the detectors, see the Sensor Reset section.

Function Keys

[1] Stay Arm [2] Away Arm [3] Chime Enable/Disable [4] Fire/Reset - Command Output# 2 [5] Quick Exit

User Commands

Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent alarm functions and status. The LCD keypad provides a written description as well as status indicator lights represent alarm functions and status. This section provides basic information regarding keypad commands. Refer to the PC1616/1832/1864 Reference Manual for detailed description of all keypad commands.

Press the [#] key to reset the keypad if an error has been made entering user codes or keypad commands.

Away Ar min g

Stay Arming

SIA

For SIA FAR listed panels, The Stay Arming Exit Delay will be twice as long as long as the Away Arming Exit Delay

Disarming

[4] Commands

[4][1] Bypass/Re-activate Stay/Away Zones

LED Keypad:

LCD Keypad:

Additional Bypass Commands:

Bypass Recall: Press [99]. Recalls the last group of zones bypassed Clear Bypass: Press [00]. Clears the bypass on all zones. Save Bypass: Press [95]. Saves zones that are manually bypassed. Recall Save: Press [91]. Recalls the bypassed zones that were saved.

Reactivate Stay/Away Zones:

Press [4][1] when the system is armed in the Stay mode to change the armed status to Away mode. The system will add the Stay/Away zones back into the system after the exit delay time expires.

[4][2] Trouble Display

LCD Programmable-Message Keypad

•Press [✱][2] to view a trouble condition.

• The trouble light will flash and the LCD will display the first trouble condition present.

• Use the arrow keys to scroll through all trouble conditions present.

When additional information is available for a specific trouble condition a

[✱] will appear on the display. Press the [✱] to view additional information.

LED Keypads, LCD Fixed Message Keypads

•Press [✱][2] to view a trouble condition.

• The trouble light will flash.

• Refer to the Trouble Summary below to determine the trouble condition(s) present

•.

Light [1] ✱ Service Required -Press [1] for more information

Light [2] AC Trouble Light [3] Telephone Line Trouble Light [4] Failure to Communicate Light [5] ✱ Zone Fault -Press [5] for more information Light [6] ✱ Zone Tamper - Press [6] for more information Light [7] ✱ Wireless Device Low Battery - Press [7] for more information Light [8] Loss of Time or Date

[1] Low Battery [2] Bell Circuit [3] General System Trouble [4] General system Tamper [5] Module Supervision [6] RF Jam Detected [7] PC5204 Low Battery [8] PC5204 AC Failure

[4][3] Alarm Memory Display

The Memory light will be ON if an alarm occurred during the last armed period. Press [4][3]. The Memory light will flash and the keypad will display the zones that went into alarm

To clear the Memory light, arm, then disarm the system.

[4][4] – Door Chime Enable/Disable

[4][5] – Program User Codes

The following table identifies available user codes:

Code Type Function

[01] – [32] [33] – [34] [40] [41] – [42]

LED Keypad:

General User Codes Duress Codes Master Code Supervisor Codes

arm, disarm transmit duress reporting code all functions arm, disarm, program user codes

Page 33

DSC PowerSeries Alarm System User Guide

6-digit user code or press [4] to delete the user code. After the user code is programmed or deleted, enter another 2-digit user to be programmed or press [#] to exit.

LCD Keypad:

Press [4][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right corner if the user code is programmed. Scroll to the appropriate user and press the [4] key to program the user (or enter the 2-digit user number). Enter a new 4-digit user code or press [4] to delete the user code. After the user code is programmed or deleted, scroll to another user or press [#] to exit.

Programming Partition Assignment:

Press [4][5] followed by the Master Code. Press [8] followed by the 2-digit user to change the partition assignment. The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is ON, the user is assigned to partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [8] followed by the 2-digit user number. When finished, press [#] to exit.

Programming User Attributes:

Press [4][5] followed by the Master Code. Press [9] followed by the 2-digit user to change the user attributes. The keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.

Light [1]-[2] For Future Use Light [3] User can manually bypass zones Light [4] User can access the Escort5580 module remotely Light [5]-[6] For Future Use Light [7] The panel will squawk the bell output when the user arms/disarms Light [8] For Future Use

[4][6] – User Functions

Press [4][6] followed by the Master Code, then press the number corresponding to the following functions.

[1]Program Time and Date: Enter the time and date using the following format

[HH:MM] [MM/DD/YY]. Program the time using military standard (e.g., 8:00

pm = 20:00 hours).

[2]Auto Arm Enable/Disable: The keypad will emit 3 rapid beeps if the Auto-

arm feature is now enabled and a steady 2-second tone if it is now disabled.

[3]Auto Arm Time/Day: Press the number corresponding to the day of the week

(1=Sunday, 2=Monday etc…) followed by the auto arm time. Program the time using military standard (e.g., 8:00 pm = 20:00 hours).

[4]System Test: The panel will perform the following; activate the bell output,

keypad buzzer and all keypad status lights for 2 seconds, test the backup battery and transmit a reporting code to the central station (if programmed).

[5]Enable DLS: The panel will temporarily enable DLS for 6 hours or 1 Hoyr.

[6]User Initiated DLS: The panel will attempt to call the DLS computer.

Additional Alphanumeric Keypad Functions:

When scrolling through the list of available functions, the following additional functions are available:

Event Buffer:View the 500-event panel buffer Brightness Control:Adjusts the display backlighting level for optimal viewing Contrast Control:Adjust the display contrast level for optimal viewing Buzzer Control:Adjust the keypad buzzer tone for optimal sound

For LED keypads, Press and hold the [ tone, then release the button.

] key to adjust the keypad buzzer

[4][7][x] – Command Output (1-4)

Press [4][7][x]. If the Command Output Code Required option is enabled, enter a valid user code. The panel will activate any PGM output assigned to the command output.

[4][9][User Code] – No-Entry Arming

[4][0] – Quick Arm/Quick Exit

Quick Arm: When disarmed, press [4][0] to arm the system. The system will arm

as if a valid user code was entered. Quick Exit: When armed, press [4][0] to activate Quick Exit. The system will allow a single zone programmed as Delay to be violated once during the following 2 minute time period without changing the status of the system.

Testing Your System

If you are going to perform a System Test, call your Monitoring Station to inform them when you begin and also when you end the test.

Keypad Sounder and Siren Test

The System Test provides several system tests, and a two-second check of the keypad sounder and bell or siren.

1. Press [Master Code] .

2. The following will occur: The system activates all keypad sounders and bells or sirens for two seconds.

All keypad lights turn ON.

- PK5500/LCD5500 keypads will light all pixels

- The Ready, Armed, and Trouble LED’s will flash for the duration of the test

3. To exit the function menu, press .

System Test

All smoke detectors in this installation must be tested by your smoke detector installer or dealer once a year to ensure they are functioning correctly. It is the user’s responsibility to test the system weekly (excluding smoke detectors). Ensure you follow all the steps in the ‘Testing Your System’ section above

If the system fails to function correctly, call your installation company for service immediately.

1. Ensure that the system is disarmed and the Ready light is on before testing.

2. Press and close all zones to return the system to the Ready state.

3. Perform a System Test by following the steps in the previous section.

4. To test the zones, activate each detector in turn (e.g., open each door/window or walk in motion detector areas).

PK5500/LCD5500 keypads will display the following message when each zone (detector) is activated: “Secure System Before Arming < >”, “Secure System or Enter Code” or “Secure or Arm System”. Use the keys to view which zones are open. The message will disappear when the zones are closed.

On an PK5501/LCD5501Z keypad, the display says “Open” when any zone (detector) is activated. To see which zones are open, press . The keypad will scroll the numbers of all open zones.

On a PK5508/PK5516/PC55XXZ keypad, the zone light turns ON when the zone (detector) is activated. The zone light turns OFF when the zone is closed (e.g., door

or window closed).

Some features described above are not functional unless enabled by your installer. Ask your installer which features are functional on your system.

Wal k Test Mode

The installer can initiate a Walk Test mode for the system. While in Walk Test mode, The Ready, Armed, and Trouble LED's will flash to indicate that Walk Test is active. When the system automatically terminates the Walk Test modes, it will annunciate with an audible warning (5 beeps every 10 seconds), beginning five minutes prior to the termination of the test.

Guidelines for locating Smoke Detectors

Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home. The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke alarms. It is recommended that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not protected by the required units. On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ ULC-S553-M86 or other appropriate national standards for installation recommendations.

• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke.

• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from entering the unit.

• Do not locate detectors in areas of high humidity.

• Do not locate detectors in areas where the temperature rises above 38 falls below 5

• Smoke detectors should always be installed in accordance with NFPA 72, the National Fire Alarm Code. Smoke detectors should always be located in accordance with the following:

‘Smoke detectors shall be installed outside of each separate sleeping area in the

immediate vicinity of the bedrooms and on each additional storey of the family living unit, including basements and excluding crawl spaces and unfinished attics. In new construction, a smoke detector also shall be installed in each sleeping room’.

C (41oF).

(100oF) or

Page 34

Download complete User manual from www.dsc.com

’Split level arrangement: Smoke detectors are required where shown. Smoke detectors are optional where a door is not provided between living room and recreation room ’.

Household Fire Safety Audit

Read this section carefully for important information about fire safety. Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be conducted and a fire escape plan be developed.

1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or household service, have a professional evaluate these units.

2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area? Cleaning with flammable liquids should be avoided.

3. Are fire-hazardous materials (matches) well out of reach of children?

4. Are furnaces and wood-burning appliances properly installed, clean and in good working order? Have a professional evaluate these appliances.

Fire Escape Planning

There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed.

1. Every family member should participate in developing the escape plan.

2. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes from sleeping quarters.

3. Escape from a bedroom must be possible without opening the interior door.

Consider the following when making your escape plans:

• Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their locking mechanisms operate smoothly.

• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue should be developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning signal.

• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use.

• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in winter; outdoor furniture or equipment should not block exits.

• Each person should know of a predetermined assembly point where everyone can be accounted for (e.g., across the street or at a neighbor’s house). Once everyone is out of the building, call the Fire Department.

• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings or pets as this wastes valuable time. Once outside, do not re-enter the house. Wait for the fire department.

• Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes to the building’s construction.

• Make sure your fire warning system is operational by conducting weekly tests. If you are unsure about system operation, contact your installing dealer.

• We recommend that you contact your local fire department and request further information on fire safety and escape planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help. The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

PC1864 Product Identifier US: F53AL01BPC1864 PC1832 Product Identifier US: F53AL01BPC1832 PC1616 Product Identifier US: F53AL01BPC1614 REN: 0.1B USOC Jack: RJ-31X

Telephone Connection Requirements

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

Ringer Equivalence Number (REN)

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format. US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Incidence of Harm

If this equipment PC1864/PC1832/PC1616 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice in or der for you to make necessary modifications to maintain uninterrupted service.

Equipment Maintenance Facility

If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user. DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122

Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It m ust be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.

Network Service

Provider's

Facilities

Telephone

Line

Network

Demarcation

Point

IMPORTANT INFORMATION

Customer Premises Equipment and Wiring

RJ-31X

Jack

Telephone

Alarm Dialing

Equipment

Answering

System

Unused

RJ-11 Jack

Fax Machine

Telephone

Computer

Unused

RJ-11 Jack

Telephone

INDUSTRY CANADA STATEMENT

NOTICE:

This Equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that that Industry Canada approved the equipment

NOTICE:

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed five.

PC1616 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1614

PC1832 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1832

PC1864 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1864

New Zealand Telecom Network

The following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network :

General Warning

The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.

Reverse Numbering (decadic signalling)

Decadic signalling should not be used as it is being progressively phased out of the network. DTMF dialling is 100% available and it should always be used..

Line Grabbing Equipment

This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls that may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer. The timing set for test calls from this equipment may be subject to 'drift'. If this proves to be inconvenient and your calls are interrupted, then the problem of timing should be discussed with the equipment installer. The matter should NOT be reported as a fault to Telecom Faults Service.

D.C. Line Feed to Other Devices

During dialling, this device unit does not provide DC voltage to the series port connection and this may cause loss of memory functions for the terminal devices (local telephone) connected to T-1, R-1.

General Operation (Ringer Sensitivity and Loading)

This device only responds to Distinctive Alert cadences DA1 and DA2.

Page 35

[013] First System Options

Opt Def ON OFF

[014] Second System Options

Opt Def ON OFF

Normally Closed Loops

Double End-of-line Resistors

Panel shows all Troubles when armed

Tampers/Faults do not show as open

Auto Arm Schedule in [*][6] and installers

Audible Exit Fault Enabled

Event Buffer Follows Swinger Shutdown

Temporal Three Fire Signal Enabled

Arm /Disarm Bell Squawk Enabled

Bell Squawk During Auto-arm

Bell Squawk On Exit Delay

Bell Squawk On Entry Delay

Bell Squawk On Trouble

Audible Exit with Urgency

Exit Delay Termination Enabled

Residential Fire Bell is Continuous

End-of-line Resistors

Single End-of-line Resistors

Panel shows only Fire Troubles when armed

Tampers/Faults show as open

Auto-arm Schedule in Installer Programming Only

Audible Exit Fault Disabled

Event Buffer Logs Events past Shutdown

Standard Pulsed Fire Signal

Arm /Disarm Bell Squawk Disabled

No Bell Squawk During Auto-arm

No Bell Squawk On Exit Delay

No Bell Squawk On Entry Delay

No Bell Squawk On Trouble

Silent Exit Delay

Exit Delay Termination Disabled

Residential Fire Bell is Cut-off

5.2 Programming Worksheets

[015] Third System Options

Opt Def ON OFF

[016] Fourth System Options

Opt Def ON OFF

Fire Key Enabled

Panic Key Audible (Bell / Beeps)

Quick Exit Enabled (ON for SIA CP-01)

Quick Arming Enabled (No Code Required)

Code Required for Bypassing

Master Code NOT Changeable (ON for SIA CP-01)

TLM Enabled

TLM Audible (Bell) when Armed

AC Trouble Displayed

Trouble Light Flashes if AC Fails

Blank Keypad when Not Used

Code required to remove Keypad Blanking

Keypad Backlighting is Enabled

Power Save Mode Enabled

Bypass Status Displayed While Armed

Keypad Tampers Enabled

9 9

9 9 9

Fire Key Disabled

Panic Key Silent

Quick Exit Disabled

Quick Arming Disabled (Code Required)

NO Code Required for Bypassing

Master Code Changeable

TLM Disabled

TLM Trouble Beeps when Armed

AC Trouble NOT Displayed

Trouble Light does NOT follow AC Status

Keypad Blanking Disabled

No Code Required

Keypad Backlighting is Disabled

Power Save Mode Disabled

Bypass Status NOT Displayed While Armed

Keypad Tampers Disabled

Page 36

PowerSeries - PC1616/PC1832/PC1864

[017] Fifth System Options

Opt Def ON OFF

WLS Key Does NOT use Access Codes

RF Jam Log after 5 Minutes

Audible RF Jam Trouble Beeps

Double Hit Enabled

Late to Close Enabled

Daylight Savings Time Enabled

Periodic Camera Test Enabled

Squawk on Away Key Arming/Disarming Only

9 9 9 9 9

WLS Key Uses Access Codes

RF Jam Log after 30 Seconds

Silent RF Jam Trouble Beeps

Double Hit Disabled

Late to Close Disabled

Daylight Savings Time Disabled

Periodic Camera Test Disabled

Squawk on all Arming/Disarming

[018] Sixth System Options

Opt Def ON OFF

Test Transmission Exception Enabled

For Future Use

Keypad Buzzer Follows Bell Enabled

Cross Zoning Enabled

Exit Delay Restart Enabled (Enabled for SIA CP-01)

AC Trouble Beeps Enabled

9 9 9 9 9 9 9 9

Test Transmission Exception Disabled

R R R R

Keypad Buzzer Follows Bell Disabled

Police Code Enabled

Exit Delay Restart Disabled

AC Trouble Beeps Disabled

[019] Seventh System Options - For Future Use

Keypad Zone Assignments

[020] Keypad Zone Assignments

Only one keypad may be assigned to a zone.

Default

00 00 00 00

I________I_______I Keypad (slot 1) Zone I________I_______I Keypad (slot 2) Zone I________I_______I Keypad (slot 3) Zone I________I_______I Keypad (slot 4) Zone I________I_______I Keypad (slot 5) Zone I________I_______I Keypad (slot 6) Zone I________I_______I Keypad (slot 7) Zone I________I_______I Keypad (slot 8) Zone

Only one keypad may be assigned to a slot. Only one zone can be assigned to a keypad. Valid entries are from 01 to 64.

[021] Eighth System Options - For Future Use [022] Ninth System Options - For Future Use

Opt Def ON OFF

For Future Use

RF Delinquency enabled

For Future Use

Audible Exit Delay for Stay Arming

9 9 9 9 9 9 9 9

R R R R R

RF Delinquency disabled

R R

Stay Arming Silent

Page 37

[023] Tenth System Options

Opt Def ON OFF

[030] Zone Loop Response (Zones 1-8)

Opt Def ON OFF

Fire Key Beeps Only

200 Baud Open/Close Identifier Toggle ON

Test Transmission While Armed Only

Test Transmission in Hours

Switching from AWAY to STAY disabled

2-way Audio will NOT Disconnect for a New Event

Trouble Beeps are Silent*

For Future Use

* This option must be off for UL residential fire applications

Zone 1 is Fast Loop Response

Zone 2 is Fast Loop Response

Zone 3 is Fast Loop Response

Zone 4 is Fast Loop Response

Zone 5 is Fast Loop Response

Zone 6 is Fast Loop Response

Zone 7 is Fast Loop Response

Zone 8 is Fast Loop Response

9 9 9 9 9 9 9 9

Fire Key Beeps and Sounds Bell

200 Baud Open/Close Identifier Toggle OFF

Test Transmission While Armed/Disarmed

Test Transmission in Days

AWAY to STAY toggle Option Permitted

2-way Audio Will Disconnect for a New Event

Trouble Beeps Sound Every 10 Seconds

R R

Zone 1 is Normal Loop Response

Zone 2 is Normal Loop Response

Zone 3 is Normal Loop Response

Zone 4 is Normal Loop Response

Zone 5 is Normal Loop Response

Zone 6 is Normal Loop Response

Zone 7 is Normal Loop Response

Zone 8 is Normal Loop Response

5.2 Programming Worksheets

Page 38

PowerSeries - PC1616/PC1832/PC1864

[101]-[164] Zone Attributes

Zone Attribute Defaults (Y = Option ON; N = Option OFF): Bold entries are opposite for SIA CP-01

Attribute: 123456 789

ON Audible Steady Chime Bypass Force* Swing Tx. Delay Wireless Zn Cross Zn

Zone Type: 00 Null Zone NNNNNNNN N 01 Delay 1 YYYYNYN NN 02 Delay 2 YYYYNYN NN 03 Instant YYYYNYN NN 04 Interior Y Y N Y N Y N NN 05 Int. Stay/Away Y Y N Y Y Y N NN 06 Dly. Stay/Away Y Y N Y Y Y N NN 07 Dly. 24hr Fire (Hardw.)YNNNNNNNN 08 Stand. 24hr Fire (Hardw.) Y N NNNNNNN 09 24hr Superv. N Y N N Y NN NN 10 24hr Superv. Buzzer N Y N Y N NNNN 11 24hr Burglary Y Y N Y N NN NN 12 24hr Holdup N Y N N N NNNN 13 24hr Gas Y N N N N NNNN 14 24hr Heating Y N N N N NN NN 15 24hr Medical Y Y N N N NNNN 16 24hr Panic Y Y N N N NN NN 17 24hr Emergency Y Y N N N NN NN 18 24hr Sprinkler Y Y N N N NN NN 19 24hr Water Y Y N N N NN NN 20 24hr Freeze Y Y N N N NNNN 21 24hr Latching Tamper Y Y N N N NN NN 22 Momentary Keyswitch N N N N Y N N N N 23 Maintained Keyswitch N N N N Y N N N N 25 Interior Delay Y Y N Y N Y N NN 26 24hr Non-alarm N N N N Y N N N N 29 Auto Verified Fire YNNNNNNNN 30 Fire Supervisory NNNNNNNN N 31 Day Zone YYNYYYYNN 32 Instant Stay/Away Y Y N Y N NN NN 35 24 hr Bell/Buzzer Y Y N Y N Y N NN 37 Night Zone Y Y N Y Y Y N NN 87 Dly. 24hr Fire (Wireless)YNNNNNNYN 88 Stand. 24hr Fire (Wireless) Y N NNNNNYN

OFF Silent Pulsed No No No No No No No

* For UL installations, do not change attribute 5 (Force Arming) from the default setting.

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn

Type** Silent Pulsed No No No No No No No

12345 6789

[101] 01 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________|

[102] 02 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[103] 03 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[104] 04 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[105] 05 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[106] 06 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[107] 07 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[108] 08 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[109] 09 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[110] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[111] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[112] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[113] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[114] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[115] 15 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[116] 16 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

Page 39

5.2 Programming Worksheets

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn

[117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[120] 20 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[121] 21 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[122] 22 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[123] 23 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[124] 24 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[125] 25 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[126] 26 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[127] 27 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[128] 28 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[129] 29 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[130] 30 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[131] 31 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[132] 32 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[133] 33 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[134] 34 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[135] 35 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[136] 36 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[137] 37 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[138] 38 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[139] 39 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[140] 40 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[141] 41 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[142] 42 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[143] 43 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[144] 44 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[145] 45 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[146] 46 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[147] 47 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[148] 48 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[149] 49 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [150] 50 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [151] 51 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [152] 52 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [153] 53 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [154] 54 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [155] 55 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [156] 56 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [157] 57 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [158] 58 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [159] 59 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [160] 60 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [161] 61 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [162] 62 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [163] 63 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [164] 64 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

Type** Silent Pulsed No No No No No No No

12345 6789

**Record here based on programming in sections [001] - [004]

Page 40

PowerSeries - PC1616/PC1832/PC1864

System Timers

[165] Maximum Dialing Attempts to Each Telephone Number

Default 005 I_______I_______I_______I Valid entries are 001-005 attempts

For UL Listed Installations, 5-10 dialing attempts are required.

[166] Post Dial Wait for Handshake (All Formats)

Default 040 I_______I_______I_______I Valid entries are 001-255 seconds

[167] T-LINK Interface Communications Wait for Acknowledge

Default 020 I_______I_______I_______I Valid entries are 001-255 seconds

[168] Set Clock Forward (Daylight Saving Time)

Def 004 Month |_______|_______|_______| Valid Entries 001-012

Def 001 Week |_______|_______|_______| Valid Entries 000-005

Def 000 Day |_______|_______|_______| Valid Entries 001-031

Def 002 Hour | _______|_______|_______| Valid Entries 000-023

Def 001 Increment |_______|_______|_______| Valid Entries 001-002

[169] Set Clock Back (Standard Time)

Def 010 Month |_______|_______|_______| Valid Entries 001-012

Def 005 Week |_______|_______|_______| Valid Entries 000-005

Def 000 Day |_______|_______|_______| Valid Entries 001-031

Def 002 Hour | _______|_______|_______| Valid Entries 000-023

Def 001 Decrement |_______|_______|_______| Valid Entries 001-002

[170] PGM Output Timer

Default 005 I_______I_______I_______I Valid entries are 001-255 seconds

[175] Auto-arm Postpone Timer

Default 000 I_______I_______I_______I Valid entries are 001-255 minutes, 000 disables automatic arming

[176] Cross Zone/Police Code Timer

Default 060 I_______I_______I_______I Valid entries are 001-255 seconds/minutes

Automatic Arming Schedule

Enter a four-digit number (HH:MM) for each day that the system will Auto-arm. All entries are disabled (9999) by default. Valid entries are 0000-2359.

Sunday Monday Tuesday Wednesday Thursday Friday Saturday

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[181]

[182]

[183]

[184]

[185]

[186]

[187]

[188]

[190] No Activity Arming Pre-Alert Time

Default Partition

001 All

I_______I_______I_______I Valid entries are 001-255 minutes, 000 for no pre-alert

Page 41

No Activity Arming Timers - Default is [000] for all partitions

Section Partition

[191] 1 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [192] 2I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [193] 3 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [194] 4 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [195] 5 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [196] 6I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [197] 7I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [198] 8 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable

[199] Auto-arming Pre-Alert Timer

Default: 004 I_______I_______I_______I Valid entries are 001-255 minutes

Partition Programming

[201] Partition Selection Mask

Opt Def ON OFF

Partition 1 is enabled

Partition 2 is enabled

Partition 3 is enabled

Partition 4 is enabled

Partition 5 is enabled

Partition 6 is enabled

Partition 7 is enabled

Partition 8 is enabled

9 9 9 9 9 9 9

Cannot be disabled

Disabled

5.2 Programming Worksheets

Default is ON for zones 1-16 on partition 1.

Partition 1 Zone Assignment Partition 2 Zone Assignment Partition 3 Zone Assignment Partition 4 Zone Assignment

[202] 1-8

[203] 9-16

[204] 17-24

[205] 25-32

[206] 33-40

[207] 41-48

[208] 49-56

[209] 57-64

Partition 5 Zone Assignment Partition 6 Zone Assignment Partition 7 Zone Assignment Partition 8 Zone Assignment

[234] 1-8

[235] 9-16

[236] 17-24

[237] 25-32

[238] 33-40

[239] 41-48

[240] 49-56

[241] 57-64

RRRRRRRR

[210] 1-8

[211] 9-16

[212] 17-24

[213] 25-32

[214] 33-40

[215] 41-48

[216] 49-56

[217] 57-64

[242] 1-8

[243] 9-16

[244] 17-24

[245] 25-32

[246] 33-40

[247] 41-48

[248] 49-56

[249] 57-64

RRRRRRRR

[218] 1-8

[219] 9-16

[220] 17-24

[221] 25-32

[222] 33-40

[223] 41-48

[224] 49-56

[225] 57-64

[250] 1-8

[251] 9-16

[252] 17-24

[253] 25-32

[254] 33-40

[255] 41-48

[256] 49-56

[257] 57-64

RRRRRRRR

[226] 1-8

[227] 9-16

[228] 17-24

[229] 25-32

[230] 33-40

[231] 41-48

[232] 49-56

[233] 57-64

[258] 1-8

[259] 9-16

[260] 17-24

[261] 25-32

[262] 33-40

[263] 41-48

[264] 49-56

[265] 57-64

RRRRRRRR

Page 42

PowerSeries - PC1616/PC1832/PC1864

Communications

[301] First Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[302] Second Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[303] Third Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

When using T-Link, program DCAA as the phone number.

[304] Call Waiting Cancel String (6 Digits)

I_______I_______I_______I_______I_______I_______I Default = DB70EF Program unused digits with Hex F

- This feature is activated in Section 382 Opt 4

All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’.

Account Codes

Enter a 6-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports 6-digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits.

Section [310] System Account Code DEF [FFFFFF]

Enter a four-digit account number for each active partition.

[311] Partition 1 Account Number [312] Partition 2 Account Number [313] Partition 3 Account Number [314] Partition 4 Account Number [315] Partition 5 Account Number [316] Partition 6 Account Number [317] Partition 7 Account Number [318] Partition 8 Account Number

|_______I_______I_______I_______I

All Account Numbers codes are defaulted to FFFF.

I_______I_______I_______I_______I_______I_______I

Reporting Codes

[320]-[323] Alarm Reporting Codes, Zones 01-64

Section

[320] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[321] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[322] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[323] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Page 43

5.2 Programming Worksheets

[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64

Section

[324] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[325] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[326] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[327] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[328] Miscellaneous Alarm Reporting Codes

I_______I_______I Duress Alarm I_______I_______I Opening After Alarm I_______I_______I Recent Closing I_______I_______I Zone Expander Supervisory Alarm I_______I_______I Zone Expander Supervisory Restore I_______I_______I Cross Zone Police Code Alarm I_______I_______I Burglary Not Verified I_______I_______I Alarm Cancelled

[329] Priority Alarm and Restoral

I_______I_______I Keypad Fire Alarm

I_______I_______I Keypad Auxiliary Alarm

I_______I_______I Keypad Panic Alarm

I_______I_______I Auxiliary Input Alarm

I_______I_______I Keypad Fire Restoral

I_______I_______I Keypad Auxiliary Restoral

I_______I_______I Keypad Panic Restoral

I_______I_______I Auxiliary Input Restore

[330]-[333] Tamper Reporting Codes, Zones 01-64

Section

[330] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[331] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[332] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[333] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Page 44

PowerSeries - PC1616/PC1832/PC1864

[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64

Section

[334] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[335] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[336] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[337] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[338] Miscellaneous Tamper Reporting Codes

I_______I_______I General System Tamper

I_______I_______I General System Tamper Rest.

I_______I_______I Keypad Lockout

[339]-[340] Closing (Arming) Reporting Codes, Access Codes 1-32

Section

[339] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[340] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[341] Miscellaneous Closing (Arming) Reporting Codes

I_______I_______I Closing by Duress Code 33

I_______I_______I Closing by Duress Code 34

I_______I_______I Closing by Master Code 40

I_______I_______I Closing by Supervisory Code 41

I_______I_______I Closing by Supervisory Code 42

I_______I_______I Partial Closing

I_______I_______I Special Closing

I_______I_______I Late to Close

I_______I_______I Exit Fault

[342]-[343] Opening (Disarming) Reporting Codes, Access Codes 1-32

Section

[342] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[343] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Page 45

5.2 Programming Worksheets

[344] Miscellaneous Opening (Disarming) Re porting Codes

I_______I_______I

Opening by Duress Code 33

Opening by Duress Code 34

Opening by Master Code 40

Opening by Supervisory Code 41

Opening by Supervisory Code 42

Auto Arm Cancellation

Special Opening

[345] Maintenance Alarm Reporting Codes [346] Maintenance Restoral Reporting Codes

I_______I_______I

Battery Trouble Alarm

AC Failure Trouble Alarm

Bell Circuit Trouble Alarm

Fire Trouble Alarm

Auxiliary Power Supply Trouble Alarm

TLM Trouble Code

General System Trouble

General System Supervisory

I_______I_______I

Battery Trouble Restoral

AC Failure Trouble Restoral

Bell Circuit Trouble Restoral

Fire Trouble Restoral

Auxiliary Power Supply Trouble Restoral

TLM Restoral

General System Trouble Restoral

General System Supervisory Restoral

[347] Miscellaneous Maintenance Reporting Codes [348] Test Transmission Reporting Codes

I_______I_______I

I___0___I___0___I

I_______I_______I

I__0____I___0___I

I___0___I___0___I

Telephone Number 1 FTC Restore

Telephone Number 2 FTC Restore

Event Buffer 75% Full Since Last Upload

DLS Lead IN

DLS Lead OUT

Zone Fault Alarm

Zone Fault Restore

Delinquency Code

General Zone Low Battery Alarm

General Zone Low Battery Restoral

Installer Lead Out

Installer Lead In

I_______I_______I

Walk Test End

Walk Begin

Periodic Test Transmission with Trouble

Periodic Test Transmission

System Test

[349] PC5700 Maintenance Reporting Codes

I_______I_______I

PC5700 Ground Fault Trouble

PC5700 Ground Fault Restore

PC5700 TLM Line 1 Trouble

PC5700 TLM Line 1 Restore

PC5700 TLM Line 2 Trouble

PC5700 TLM Line 2 Restore

[350] Communicator Format Options

Default

I_______I_______I 1st Telephone Number

I_______I_______I 2nd Telephone Number

01 20 BPS, 1400 HZ handshake 05 Pager 08 10 BPS, 2300Hz handshake 11 For Future Use 02 20 BPS, 2300 HZ handshake 06 Residential Dial 09 Private Line 12 Robofon 03 DTMF CONTACT ID 07 10 BPS, 1400Hz handshake 10 Scantronics 13 CESA 200 04 SIA FSK

Page 46

PowerSeries - PC1616/PC1832/PC1864

Call Direction Options [351]-[358] Alarm/Restore Communicator Call Directions

Option 3 Not Used (Def OFF)

Section Partition

Option 1

1st Telephone

Number (Def ON)

Option 2

2nd Telephone

Number (Def OFF)

Option 4

Not Used

(Def OFF)

Option 5

Alt Comm

(Def ON)

Options 6,7,8

Future Use

[351] 1 [352] 2 [353] 3 [354] 4 [355] 5 [356] 6 [357] 7 [358] 8

I________I I________I I________I I________I I________I I________I

[359]-[366] Tamper/Restore Communicator Call Directions

Section Partition

[359] 1 [360] 2 [361] 3 [362] 4 [363] 5 [364] 6 [365] 7 [366] 8

Option 1

1st Telephone

Number (Def ON)

I________I I________I I________I I________I I________I I________I

Option 2

2nd Telephone

Number (Def OFF)

Option 3 Not Used (Def OFF)

[367]-[374] Opening/Closing Communicator Call Directions

Section Partition

Option 1

1st Telephone

Number (Def OFF)

Option 2

2nd Telephone

Number (Def OFF)

Option 3

Not Used

(Def OFF)

Option 4 Not Used (Def OFF)

Option 5

Alt Comm

(Def ON)

Option 5

Alt Comm

(Def OFF)

Options 6,7,8

Future Use

Options 6,7,8

Future Use

[367] 1 [368] 2 [369] 3 [370] 4 [371] 5 [372] 6 [373] 7 [374] 8

I________I I________I I________I I________I I________I I________I

[375] System Maintenance Commun icator Call Directions

Section

[375]

Option 1

1st Telephone

Number (Def ON)

I________I I________I I________I I________I I________I I________I

Option 2

2nd Telephone

Number (Def OFF)

Option 3 Not Used (Def OFF)

[376] System Test Trans mis si o ns Communicato r Ca ll D irec t ions

Option 3 Not Used (Def OFF)

Section

[376]

Option 1

1st Telephone

Number (Def ON)

I________I I________I I________I I________I I________I I________I

Option 2

2nd Telephone

Number (Def OFF)

Option 4 Not Used (Def OFF)

Option 5

Alt Comm

(Def ON)

Option 5

Alt Comm

(Def ON)

Options 6,7,8

Future Use

Options 6,7,8

Future Use

Page 47

[377] Communication Variables

Default

003 I___0__I__0__I___1__I Swinger Shutdown (Alarms and Rest) 001-014 Transmissions

003

000

030

010

030

007

030

000

†Dependent on programming in section [702], option [3].

I___0__I__0__I___3__I Swinger Shutdown (Tampers and Rest) 001-014 Transmissions, 000=disabled I___0__I__0__I___3__I Swinger Shutdown (Maint and Rest) 001-014 Transmissions, 000=disabled I___0__I__3__I___0__I Communication Delay 001-255 seconds I___0__I__3__I___0__I AC Failure Communication Delay 001-255 minutes I___0__I__1__I___0__I TLM Trouble Delay No. of checks required - valid entries 003 - 255) I___0__I__3__I___0__I Test Transmission Cycle (land line) 001-255 days/minutes† I___0__I__3__I___0__I For Future Use I___0__I__0__I___7__I Zone Low Battery Transmission Delay 000-255 days I___0__I__3__I___0__I Delinquency Transmission Cycle 000-255 days/hours I___0__I__0__I___5__I Communications Cancelled Window 000-255 minutes

For UL installations, the Entry Delay plus Communication Delay time must not exceed 60 seconds.

To disable the AC failure communications delay, program [000].

[378] Test Transmission Time of Day

Default

9999 I_______I_______I_______I_______I Valid entries are 0000-2359 (9999 to disable)

5.2 Programming Worksheets

[380] First Communicator Options

Opt Def ON OFF

9 R

Communications Enabled

Restorals on Bell Time-out

Pulse Dialing

Switch to Pulse Dialing on 5th Attempt

3rd Telephone Number Enabled

Alternate Dial (1st & 3rd)

For Future Use

Delinquency Follows Zone Activity (Hours)

9 R

Communications Disabled

Restorals Follow Zones

DTMF Dialing

DTMF Dial For All Attempts

3rd Telephone Number Disabled

Call 1st Number, Back up to 3rd

Delinquency Follows Arming (Days)

[381] Second Communicator Options

Opt Def ON OFF

9 R

Open After Alarm Keypad Ringback Enabled

Open After Alarm Bell Ringback Enabled

SIA Sends Programmed Reporting Codes

Closing Confirmation Enabled

Talk/Listen on Phone Lines 1/3

Talk/Listen on Phone Line 2

Contact ID Uses Programmed Reporting Codes

For Future Use

9 R

Open After Alarm Keypad Ringback Disabled

Open After Alarm Bell Ringback Disabled

SIA Sends Automatic Reporting Codes

Closing Confirmation Disabled

No Talk/Listen on Phone Lines 1/3

No Talk/Listen on Phone Line 2

Contact ID Uses Automatic Reporting Codes

Page 48

PowerSeries - PC1616/PC1832/PC1864

[382] Third Communicator Options

Opt Def ON OFF

*This option must remain OFF for SIA-FAR installations. ** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.

Contact ID Partial Closing Identifier is “5”

Alarm Communications Enabled During Walk Test*

Communication Cancelled Message Enabled (ON for SIA CP-01)

Call Waiting Cancel Enabled**

T-Link Interface Enabled

AC Failure Transmission Delay is in Hours

For Future Use

Contact ID Partial Closing Identifier is “4”

Alarm Communications Disabled During Walk Test

Communication Cancelled Message Disabled

Call Waiting Cancel Disabled

T-Link Interface Disabled

AC Failure Transmission Delay is in Minutes

R R R

DLS Downloading

[401] Downloading Option Codes

Opt Def ON OFF

Answering Machine/Double Call enabled

User Can Enable DLS Window

Call Back Enabled

User Initiated Call Up Enabled

Auto Event Buffer Upload Enabled

For Future Use

Answering Machine/Double Call enabled

User Cannot Enable DLS Window

Call Back Disabled

User Initiated Call Up Disabled

Auto Event Buffer Upload Disabled

R R R R

[402] DLS Downloading Telephone Number (32 Digits)

|____D___|_______|_______|_______|_______|_______|_______|___ ____|_______|_______|_______|_______|_______|_______|_______|_ ______|_______|_______|_______|_______|_______|_______|__ _____|_______|_______|_______|_______|_______|_______|___ ____|_______|_______|

[403]-[404] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits)

Panel Default [403] Downloading Access Code [404] Panel ID Code

PC1616 161600

PC1832 183200

PC1864 186400

[405] Answering Machine Double Call Timer

Default 060 (001-255 seconds)

[406] Number of Rings to Answer On

Default 000 (001-255 rings)

[499] Initiate PC-Link Downloading

Enter [499][Installer Code][499]

|_______|_______|_______|_______|_______|_______| |_______|_______|_______|_______|_______|_______|

Page 49

5.2 Programming Worksheets

[501]- [554]Programmabl e Output Attributes

Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009], [010] & [011].

PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF):

Attribute: 12 3 4 5 678

Not used Not used True Output Follows Timer Code Req. Not used Not used Not used

OFF

PGM Option

[01] Residential Burglary / Fire Bell Output

[02] For Future Use

[03] Sensor Reset [4][7][2]

[04] 2-Wire Smoke Support (PGM2 only)

[05] System Armed Status

[06] Ready To Arm

[07] Kypad Buzzer Follower Mode

[08] Courtesy Pulse

[11] System Tamper (all sources, zones, keypad, modules)

[12] TLM and Alarm

[13] Kiss-off Output

[14] Ground Start Pulse

[15] Remote Operation (DLS Support)

[16] For Future Use

[17] Away Armed Status

[18] Stay Armed Status

[19] Command Output #1, [4][7][1]

[20] Command Output #2, [4][7][2]

[21] Command Output #3, [4][7][3]

[22] Command Output #4, [4][7][4]

[23] 24 Hr Silent Input (PGM2 only)

[24] 24 Hr Audible Input (PGM2 only)

[25] Delayed Burglary & Fire Output

[30] Partition Status Alarm Memory Output

— — Inverted On / Off No Code Req. — — —

YN Y Y Y Y Y Y Y YY YY YY Y Y Y YY Y YY N YY N YY N Y Y Y Y

Attribute:

PGM Option

[09] System Trouble

[10] System Event

[29] Zone Follower

123456 7 8

ON Serv. req. AC Fail TLM Fault FTC Zone Fault Zone Tmp. Zn. Low Bat. Loss of Clock

OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled

YYYYYY Y Y

ON Bu r g . Evn t . Fire

OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Latched

Evnt.

YYYYYYY N

*If attribute [8] is turned ON, attributes [1-7] must also be turned ON.

Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8

NNNNNNN N

Panic Evnt. Med. Evnt. Supv. Evnt. Priority Evnt. Holdup Evnt. Follows Timer*

Page 50

PowerSeries - PC1616/PC1832/PC1864

Section PGM Output 1 2 3 4 5 6 7 8

#Type*

Main Board

[501] 1 ( )

I________I I________| I________| I________| I________| I________| I________| I________I

[502] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

Main Board / PC5208

[503] ** 3 ( )

I________I I________| I________| I________| I________| I________| I________| I________I

[504] ** 4 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in [009], [010] and [011]. ** These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the

PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4 will work the same as the second PC5208 output.

Section PGM Output 1 2 3 4 5 6 7 8

#Type*

PC5208

[505] 5 ( )

I________I I________| I________| I________| I________| I________| I________| I________I

[506] 6 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[507] 7 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[508] 8 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[509] 9 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[510] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

PC5204

[511] 11 ( )

I________I I________| I________| I________| I________| I________| I________| I________I

[512] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[513] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[514] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in [009], [010] and [011].

PGM Output Partition Assignment

Section PGM Partition: 1 2 3 4 5 6 7 8

Main Board

[551] 1 I________I I________| I________| I________| I________| I________| I________| I________I

[552] 2 I________I I________| I________| I________| I________| I________| I________| I________I

Main Board / PC5208

[553] 3

[554] 4 I________I I________| I________| I________| I________| I________| I________| I________I

PC5208

[555] 5

[556] 6 I________I I________| I________| I________| I________| I________| I________| I________I

[557] 7 I________I I________| I________| I________| I________| I________| I________| I________I

[558] 8 I________I I________| I________| I________| I________| I________| I________| I________I

[559] 9 I________I I________| I________| I________| I________| I________| I________| I________I

[560] 10 I________I I________| I________| I________| I________| I________| I________| I________I

PC5204

[561] 11

[562] 12 I________I I________| I________| I________| I________| I________| I________| I________I

[563] 13 I________I I________| I________| I________| I________| I________| I________| I________I

[564] 14 I________I I________| I________| I________| I________| I________| I________| I________I

I________I I________| I________| I________| I________| I________| I________| I________I

Page 51

INTERNATIONAL PROGRAMMING

[700] Automatic Clock Adjust

Default = 60 |________|_________| Valid Entries 00-99 Seconds

[701] First International Options

Opt Def ON OFF

[702] Second International Options

Opt Def ON OFF

50 Hz AC

Time Base - Internal Crystal

AC/DC Arming Inhibit Enabled

All System Tampers Require Installer Reset

6-digit User Access Codes

Busy Tone Detection Enabled

High Current Battery Charge

DLS/Audio has no priority

Pulse Dialing Make/Break Ratio is 33/67

Force Dialing Enabled

Land Line Test Transmission in Minutes

1600 Hz Handshake

ID Tone Enabled

2100 Hz ID Tone

One Time 1-Hr User Enabled DLS Window

Bell on FTC when Armed

9 9 9 9 9 9 9 9

9 9 9 9 9 9

60 Hz AC

Time Base - AC Line

AC/DC Arming Inhibit Disabled

All System Tampers Follow Restore

4-digit User Access Codes

Busy Tone Detection Disabled

Standard Current Battery Discharge

DLS/Audio has priority

Pulse Dialing Make/Break Ratio is 40/60

Force Dialing Disabled

Land Line Test Transmission in Days

Standard Handshake

ID Tone Disabled

1300 Hz ID Tone

Full 6-Hr User Enabled DLS Window

FTC Trouble only when Armed

5.2 Programming Worksheets

[703] Delay Between Diali ng Attempts

Default = 003 |________|_________|_________| Valid Entries 000-255 Seconds

Module Programming

[801] PC5400 Printer Module Programming

Refer to the PC5400 Installation Manual for installation and programming instructions.

[802] PC59xx VOX Module Programming

Refer to the PC59xx Installation Manual for installation and programming instructions.

[803] Alternate Communicator Programming

Refer to the Skyroute or PC5400 Sur-Gard DVACS Installation Manual for installation and programming instructions.

[804] PC5132 Wireless Expansion Programming

Refer to the PC5132 Installation Manual for programming locations and instructions.

[805] PC5100 Programming

Refer to the PC5100 Installation Manual for programming locations and instructions.

[851] T-Link Programming

Refer to the T-Link Installation Manual for programming locations and instructions.

Page 52

PowerSeries - PC1616/PC1832/PC1864

Special Installer Functions

[900] Panel Version Displa yed [901] InstallerWalk Test Mode Enable/Disable [902] Module Supervision Reset [903] Module Supervision Field [904] Wireless Module Placement Test [905] - [909] For Future Use [990] Installer Lockout Enable [991] Installer Lockout Disable [992] For Future Use [993] Restore Alternate Communicator to Default Programming [994] For Future Use [995] Restore Escort5580 to Default Programming [996] Restore PC5132 to Default Programming [997] Restore PC5400 to Default Programming [998] Restore PC59xx to Default Programming [999] Restore Control Panel to Default Programming

Page 53

Appendix A: Reporting Codes

The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes about individual reporting codes, (see Section 5.6 Communicator Programming PWS Sect 6).

Contact ID

The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would receive the following:

*BURG - ENTRY/EXIT - 1 where the “1” ind icates w hich z one w ent into alarm.

SIA Format - Level 2 (Hardcoded)

The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October

1997. This format will send the Account Code along with its data transmission. The transmission will look similar to the following at the receiver:

N Ri01 BA 01

N = New Event

Ri01 = Partition /Area Identifier

BA = Burglary Alarm

01 = Zone 1

NOTE: A system event will use the Area Identifier Ri00.

Section # Reporting Code Code Sent When...

[320]-[323] Zone Alarms Zone goes into alarm A/R See Table 3 See Ta ble 3 [324]-[327] Zone Restorals Alarm condition has been restored A/R [328] Duress Alarm Duress code entered at keypad A/R (1) 21 HA-00 [328] Opening After Alar m System disarmed with alarm in memory A/R (4) 58 OR-UU [328] Recent Closing Alarm occurs within two minutes of system arming A/R (4) 59 CR-00 [328] Zone Expander Supervisory

[328] Cross Zone (Police Code)

[328] Burglary Not Verified A/R (3) 78 BG-00 [328] Alarm Cancelled A/R (4) A6 BC-00 [329] [F] Key Alarm/Rest. Keypad fire alarm (alarm and restore rep. codes sent together) A/R (1) 1A FA-00/FH-00 [329] [A] Key Alarm/Rest. Keypad auxiliary alarm (alarm and restore rep. codes sent

[329] [P] Key Alarm/Rest. Keypad panic alarm (alarm and restore rep. codes sent together) A/R (1) 2A PA-00/PH-00 [329] Aux Input Alarm/Rest Option#23/24: a panic button wired to PGM 2 is pressed/access

[330]-[337] Zone Tamper/Restoral Zone is tampered / tamper condition restored T/R (3) 83 TA-ZZ/TR-ZZ [338] General System Tamper/

[338] Keypad Lockout Maximum number of incorrect access codes has been entered at

[339-341] Closings System armed (user 01-34, 40-42 indicated) O/C (4) A1 CL-UU [341] Partial Closing One or more zones bypassed when system armed O/C (4) 56 CG-ZZ [341] Special Closing Closing (arming) using one of the following methods: quick arm,

[341] Late to Close Whenever the Auto-arm prealert sounds (if the Late to Close

[341] Exit Fault O/C (3) 74 EE-00 [342-344] Openings System disarmed (user 01-34, 40-42 indicated) O/C (4) A1 OP-UU [344] Auto-arm Cancellation Auto-arm cancelled O/C (4) 55 CI-00 [344] Special Opening Opening (disarming) using one of the following methods: key-

[345]-[346] Battery Trouble/Rest. PC1616/PC1832/PC1864 battery is low/battery restored MA/R (3) A2 YT-00/YR-00 [345]-[346] AC Line Trouble/Rest. AC power to control panel is disconnected or interrupted/AC

[345]-[346] Bell Circuit Trouble/Rest. Open or short circuit detected across bell terminals/bell circuit

[345]-[346] Fire Trouble/Rest. Trouble occurs/restores on a f ire zone MA/R (3) 73 FT-99/FJ-99

Alarm/Rest.

Alarm

Rest.

Panel loses/restores supervi s ory transmission over the Keybus from zone expansion modules, or keypads with zone inputs

Two zones on the same part ition go into alarm during any given armed-to-arm ed period (incl. 24Hr zones)

together)

code is entered Option #04: a 2-wire smoke detector wired to PGM 2 goes into

alarm/alarm is cleared.

Enrolled module with tamper inputs has a tamper ala rm/all module tampers restored

a keypad

auto arm, keyswitch, function key, maintenance code, DLS software, wireless key

option is enabled)

switch, maintenance code, DLS software, wireless key

power restored (Both codes follow AC Failure Comm. Delay.)

restored

Dialer

Direction*

A/R (1) 43 UA-00/UH-00

A/R (1) 39 BM-00/BV-00

A/R (1) AA MA-00/MH-00

A/R A/R

T/R (1) 45 ES-00/EJ-00

T/R (4) 61 JA-00

O/C (4) AA CL-00

O/C (4) 54 CI-00

O/C (4) AA OP-00

MA/R (3) A1 AT-00/AR-00

MA/R (3) 21 YA-99/YH-99

Automatic

Contact ID

Codes

(1) 4A (1) 11

SIA Auto

Rep Codes**

UA-99/UH-99 FA-99/FH-99

Page 54

PowerSeries - PC1616/PC1832/PC1864

Section # Reporting Code Code Sent When...

[345]-[346] Auxiliary Power Trouble/

Rest.

Aux voltage supply trouble/restoral MA/R (3) 12 YP-00/YQ-00

Dialer

Direction*

Automatic Contact ID

Codes

SIA Auto

Rep Codes**

[345] TLM Failure Telephone line monitoring trouble MA/R (3) 51 LT-01 [346] TLM Restore Telephone line restored MA/R (3) 51 LR-01 [345]-[346] Gen System Troub le/Res t. “Service Required” trouble occurs (view troub l es usin g [*][2]) /trou-

[345]-[346] Gen System Supervisory

Trouble/Rest.

[347] Phone# 1 or 2 FTC Restoral Control panel has restored communications to central station on

ble restored Control panel loses/restores communications with module(s)

connected to the Keybus

Phone# 1 or 2 (after FTC)

MA/R (3) AA YX-00/YZ-00

MA/R (3) 3A ET-00/ER-00

MA/R (3) 54 YK-00

[347] Event Buffer is 75% Full Event buffer is almost full since last upload MA/R (6) 22 JL-00 [347] DLS Lead In Downloading session start MA/R (4) 11 RB-00 [347] DLS Lead Out Downloading session complete MA/R (4) 12 RS-00 [347] Zone Fault/Rest. One or more zones have faults/restored MA/R (3) 80 UT-ZZ/UJ-ZZ [347] Delinquency Programmed amount of time (days or hours) for delinquency has

MA/R (6) 54*** CD-00

expired without zone activity, or without system being armed

[347] Wireless Device Low Battery

Trouble/Rest.

Wireless zones, panic pendants, handheld keypads, wireless keys have low battery/all low batteries restored

MA/R (3) 84 XT-00/XR-00

XT-ZZ/XR-ZZ**** [347] Installer Lead In Installer’s mode has been entered MA/R (6)27 LB-00 [347] Installer Lead Out Installer’s mode has been exited MA/R (6)28 LS-00 [348] Walk Test End End of test T (6) A7 TE-00 [348] Walk Test Begin Beginning of test T (6) A7 TS-00 [348] Periodic Test with Trouble Periodic system test transmission wit h trouble T (6) A8 RY-00 [348] Periodic Test Periodic system test transmission T (6) A2 RP-00 [348] System Test [*][6] bell/communications test T ( 6) A1 RX-00 [349] PC5700 Ground Fault Trou-

[349] PC5700 TLM Line 1 Trouble/

ble/Restore

Restore

[349] PC5700 TLM Line 2 Trouble/

Ground/Fault/Trouble occurs on the PC5700 MA/R (3) 1A US-00/UR-00

TLM Trouble /Restore occurs on the PC5700 MA/R (3) 51 LT-01/LR-01

TLM Trouble /Restore occurs on the PC5700 MA/R (3) 52 LT-02/LR-02

Restore

* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions ** UU = user number (user01-42); ZZ = zone number (01-64) *** Use the “Fail to close” event code [(4)54] to report closing or activity delinquency. Ensure the central station is aware t hat this code is used. **** Zones are identified, panic pendants, wireless keys, and handheld keypads are not.

Contact ID Zone Alarm/Restoral Event Codes

(as per SIA DCS: ‘Contact ID’ 01-1999): Program any of these codes for zone alarms/restorals when

using the standard (non-automatic) Contact ID reporting format.

Medical Alarms (1)34 Entry / Exit

(1)AA Medical (1)35 Day / Night (1)A1 Pendant Transmitter (1)36 Outdoor (1)A2 Fail to Report In (1)37 Tamper

Fire Alarms (1)38 Near Alarm

(1)1A Fire Alarm General Alarms (1)11 Smoke (1)4A General Alarm (1)12 Combustion (1)43 Exp. module failure (1)13 Water Flow (1)44 Sensor tamper (1)14 Heat (1)45 Module Tamper (1)15 Pull Station (1)4A Cross Zone Police Code (1)16 Duct 24 Hour Non-Burglary (1)17 Flame (1)5A 24 Hour non-Burg (1)18 Near Alarm (1)51 Gas detected

Panic Alarms (1)52 Refrigeration

(1)2A Panic (1)53 Loss of Heat (1)21 Duress (1)54 Water Leakage (1)22 Silent (1)55 Foil Break (1)23 Audible (1)56 Day Trouble

Burglar Alarms (1)57 Low bottled Gas level

(1)3A Burglary (1)58 High Temp (1)31 Perimeter (1)59 Low Temp (1)32 Interior (1)61 Loss of Air Flow (1)33 24 Hour

SIA Format Automatic Zone Alarm/Restoral Codes

Zone Definition SIA Auto Rep

Delay 1 BA-ZZ/BH-ZZ (1) 3A Delay 2 BA-ZZ/BH-ZZ (1) 3A Instant BA-ZZ/BH-ZZ (1) 3A Interior BA-ZZ/BH-ZZ (1) 3A Interior Stay/Away BA-ZZ/BH-ZZ (1) 3A Delay Stay/Aw ay BA-ZZ/BH-ZZ (1) 3A Delayed 24-Hr Fire FA-ZZ/FH-ZZ (1) 1A Standard 24-Hr Fire FA-ZZ/FH-ZZ (1) 1A 24-Hr Supervisory US-ZZ/UR-ZZ (1) 5A 24-Hr Supervisory Buzzer UA-ZZ/UH-ZZ (1) 5A 24-Hr Burg BA-ZZ/BH-ZZ (1) 3A 24-Hr Holdup HA-ZZ/HH-ZZ (1) 22 24-Hr Gas GA-ZZ/GH-ZZ (1) 51 24-Hr Heat KA-ZZ/KH-ZZ (1) 58 24-Hr Medical MA-ZZ/MH-ZZ (1) AA 24-Hr Panic PA-ZZ/PH-ZZ (1) 2A 24-Hr Emergency (non-medical) QA-ZZ/QH-ZZ (1) A1 24-Hr Sprinkler SA-ZZ/SH-ZZ (1) 13 24-Hr Water WA-ZZ/WH-ZZ (1) 54 24-Hr Freeze ZA-ZZ/ZH-ZZ ( 1) 59 24-Hr Latching UA-ZZ/UH-ZZ (1) 4A Interior Delay BA-ZZ/BH-ZZ (1) 3A Auto Verified Fire FA-ZZ/FH-ZZ (1) 1A 24-Hr Fire Supervisory FS-ZZ/FV-ZZ (2) AA Day Zone BA-ZZ/BH-ZZ (1) 3A Instant Stay/Away BA-ZZ/BH-ZZ (1) 3A 24-Hr Bell/Buzzer UA-ZZ/UH-ZZ (1) 5A Night Zone BA-ZZ/BH-ZZ (1) 3A Delayed 24-Hr Fire (Wireless) FA-ZZ/FH-ZZ (1) 1A Standard 24-Hr Fire (Wireless) FA-ZZ/FH-ZZ (1) 1A

Codes*

Contact ID Auto Rep Codes*

* ZZ = zones 01-64

Page 55

Appendix B: UL Listed Commercial and Residential Installations

The installation requirements listed below must be met for the following grades of service.

Central Station and Police Connect (Standard or Encrypted Line Security Service)

The installation must use T-Link module which communicates over LAN/WAN to the Sur-Gard MLR-IP receiver or the TL200/250 which communicates over LAN/ WAN/Internet to the SG System III receiver. Polling time must be 90 seconds. Compromise detection time must be 6 minutes.

Local

•The installation must have a bell which is UL Listed for mercantile local alarms (AMSECO MBL10B with model AB-12 bell housing).

•The digital communicator must be enabled.

•The control panel must be in the attack-resistant enclosure (DSC Model CMC1 or PC4050CAR).

Central Station and Police Connect (No line security)

•The installation must have a bell which is UL Listed for mercantile local alarms (AMSECO MBL10B with model AB-12 bell housing).

•The digital communicator must be enabled.

•The control panel must be in the attack resistant enclosure (DSC Model CMC1 or PC4050CAR).

All Commercial Installations

•The Entry Delay must not exceed 120 seconds

•The Exit Delay must not exceed 120 seconds.

•The minimum Bell Time-out is 15 minutes.

Residential Fire & Burglary Installations

•The Entry Delay must not exceed 45 seconds

•The Exit Delay must not exceed 60 seconds.

•The minimum Bell Time-out is 4 minutes.

Home Health Care Signaling Equipment

•There must be at least two keypads, one of either the LCD5500Z/LCD5520Z or LCD5501Z and one of the following models, PC5508Z, PC5516Z or PC5532Z.

•Each system shall be programmed to activate an audible Trouble signal within 90 seconds upon loss of microprocessor memory.

•The minimum Bell Time-out is 5 minutes.

Programming

The notes in the programming sections describing the system configurations for UL Listed installations must be implemented.

Control of the Protected Premises

In order to have a UL Certificated system the protected area is to be under the responsibility of one ownership and management (i.e., one business under one name). This may be a group of buildings attached or unattached with different addresses but under the responsibility of someone having mutual interest. The person of mutual interest is not the alarm-installing company.

Bell Location

The alarm sounding device (bell) must be located where it can be heard by the person or persons responsible for maintaining the security system during the daily arming cycle.

Protection of the Control Unit

The local control and the local power supply must be protected in one of the following ways:

•The control unit and audible alarm device must be in a protected area which is armed 24 hours a day.

•Each partition must arm the area protecting the control unit and the audible alarm device power supply. This may require duplicate protection armed by each partition. Access to this protected area, without causing an alarm, will require that all partitions be disarmed.

•In all cases described above, the protected area for the control unit must be programmed as not-bypassable.

Casual Users

The installer should caution the user(s) not to give system information to casual users (e.g. codes, bypass methods, etc. to baby-sitters or service people). Only the One-Time Use codes should be given to casual users.

User Information

The installer should advise the users and note in the User’s Manual:

•Service organization name and telephone number

•The programmed exit time

•The programmed entry time

•Test system weekly

Two-Wire Smoke Detector Compatibility (if available)

Maximum loop resistance: 24 Ohms

•Operating Voltage Range: 9.8 - 13.8 VDC

•Maximum Alarm Current: 89 mA

•Compatibility Identifier: PC18-1

See

Section 1.6 PGM Wiring

for compatible 2-wire smoke detectors.

SIA FAR Installations

Minimum requirement system for SIA-FAR Installations:

• 1 PC1616/PC1832/PC1864 Control panel

• 2 Local annunciation devices

The local annunciation devices may be any combination of the following keypads, as long as there is at least one LCD keypad in the installation (Model LCD5500Z, LCD5501Z, PKP-LCD, PKP-ICN or PK5500).

• LCD5500Z • LCD5501Z • PK5500 • PK5508

• PKP-LCD • PKP-ICN • PK5501 • PK5516

The following optional subassembly modules also bear the SIA FAR classification and may be used if desired:

PC5108 Zone Expander Module

Compatible initiating devices: Bravo200 series, 300 series, 400 series, 500 series, 600 series, AC-100, Encore300 series, Force200 series, 210 series, MN240.

PC5208 Low Current PGM Output Module

The following optional accessory modules also bear the SIA FAR classification and may be used if desired.

PC5204 Auxiliary Power Supply with PGM output ports Escort5580/Escort5580TC, PC5400 Printer Module

Caution

• For SIA FAR installations, only use modules / devices that are listed on this page.

• Fire Alarm Verification feature (Auto Verified Fire zone) is not supported on 2-wire smoke detectors zones. This feature may be enabled for 4-wire smoke detectors only.

• Call Waiting Cancel (Section 382 Option 4) feature on a non-Call Waiting line will prevent successful communication to the central station.

• All smoke detectors on the system must be tested annually by conducting the Installer Walk Test prior to exiting the walk test mode, a sensor reset must be conducted on the system, [4][7][2] to reset all latching 4-wire smoke detectors. Please refer to the smoke detector installation instructions on how to correctly test the detectors.

Notes

• Programming at installation may be subordinate to other UL requirements for the intended application.

• Cross zones have the ability to individually protect the intended area (e.g., motion detectors, which overlap).

• Cross zoning is not recommended for line security Installations nor is it to be implemented on exit / entry zones.

• There is a communication delay of 30 seconds in this control panel. It can be removed, or it can be increased up to 45 seconds at the option of the end user by consulting with the Installer.

• Do not duplicate any reporting codes. This applies for all communication formats other than SIA sending automatic programmed reporting codes.

• The control unit must be installed with a local sounding device and an offpremise transmission for SIA communication format.

• For ULC Listed Fire Monitoring Installations & module requirements, Refer to the ULC Installation Information sheet, part# 29002157.

• Use a CSA/cUL transformer, hardwired.

• All tamper circuits may be connected to the same zone.

• Use ULC-LA for AC Power indication.

Page 56

PowerSeries - PC1616/PC1832/PC1864

Appendix C: SIA False Alarm Reduction

SIA Feature

Programming Section

Exit Time

[005], 3rd entry

Progress Annunciation/ Disable - for Silent Exit

[014], Option 6 ON

Exit Time Restart

[018], Option 7 ON

Auto Stay Arm on Unvacated Premises

[001]-[004] Zone type 05, 06

Exit Time and Progress Annunciation/Disable or Remote Arming

[005] and [014] bit 6

Entry delay(s)

[005], 1st and 2nd entry

Abort Window for Non-Fire zones

[101]-[164] bit 7 ON

Abort Window - for Non-Fire zones

[377], 4th entry

Abort Annunciation

[382], Option 3 ON

Cancel Annunciation

[328], 8th entry

Duress Feature

[*][5] Master Code 33rd and 34th entries

Cross Zoning

[018] Option 6 [101]-[164] bit 9 OFF

Cross Zone Timer

[176]

Swinger Shutdown for Alarms

[377] 1st entry

Swinger Shutdown Disable

[101] - [164] bit 6 ON

Fire Alarm Verification

Zone type [29]

Call Waiting Cancel Dial String

[304], [382], Option 4 OFF

System Test:

[*][6] Master Code, Option 4

Installer Walk Test Mode:

[901]

Alarm Communications During Walk Test

[382] Option 2:

Walk Te st End and Begin Reporting Codes

and 2nd Entries

[348], 1

Comments Range/Default Require-

Access to Entry and Exit delays for each partition and Bell Time Out for the system For Full or auto arming:

Enables audible exit beeps from the keypad for the duration of exit delay Individual keypads

Enables the exit delay restart feature

Function Key: Stay Arming. All Stay/Away type zones (05, 06) will be automatically bypassed

System Times and Audible Exit beeps can be d isab led when using the Key fob to arm away the system

Access to Entry and Exit delays for each partition and Bell Time Out for the system

Note:

Combined Entry delay and Communications Delay (Abort Window) shall not

exceed 60s Access to zone attributes, i.e, swinger shutdown, transmission delay and cross zone.

Individual zones attribute bit 7 (Transmission delay) is by default ON

Access to the programmable delay bef ore communicating alarms

Note:

Combined Entry delay and Communications Delay (Abort Window) shall not

exceed 60s Enables the “Communication Cancelled" message display on all keypads Annunciate that no

Access to the reporting code for Alarm Cancelled Annunciate that a

Do not derive code from an existing Master/User code (e.g., Master code is 1234, the duress code should not be 1233 or 1235)

This option enables Cross Zoning for entire system. Individual zones can be enabled for Cross zoning via Zone attribute bit 9 in sections [101] - [164]

Access to the programmable Cross Zone timer May program

Access to the swinger shutdown limit for zone alarms For all non-fire zones

Access to zone attributes, i.e., swinger shutd own, transmission de la y and cross z one . Individual zones attribute bit 6 (Swinger shutdown enabled) is by default ON

Auto V e rified Fire, use only with 4 wire type detectors that can be reset by the panel 4wire smoke detector powered from AUX + and PGM1 - PGM4 (type 03, Sensor reset)

Access to the dialing sequence used to disable call waiting Dependant on user phone

Testing

The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on. Refer to the User Manual (part no. 29007165).

This mode is used to test each zone on the system fo r proper functionality.

Enables Communication of zone alarms while installer Walk Test is active.

Access to the reporting codes for Walk Test Begin and Walk Test End.

Range:

45- 255 seconds

Default:

60 sec.

may be disabled

Default:

All Enabled

Default:

Enabled Required

If no exit after full arm

Default:

Enabled

Default:

Enabled Allowed

Range:

30 sec. to 4 min.

Default:

30 sees

May be disabled by zone or zone type

Default:

Enabled

Range:

15 - 45 sec.

Default:

30 sees

alarm was transmitted

Default:

Enabled

Cancel was transmitted

Default:

Enabled

No 1+ derivative of another user code. No duplicates with other user codes

Default:

disabled

Programming required

Default:

Disabled

Range: 001-255 sec./min.

Default:

60 secs

shut down at 1 or 2 trips

Default:

1 Trip

For non-police response zones

Default:

Enabled

70 seconds reset and confirmation time

Default:

disabled

line

Default:

disabled

ment

Required (programmable)

Allowed

Required

Required (programmable)

Required

Required (programmable)

Required

Allowed

Required

Allowed

Required (programmable)

Allowed

Required

Page 57

Appendix D: Troubleshooting Guide

Testing:

• Power up system

• Program options as required (See Programming Section) NOTE: For advanced programming refer to the PC1616/1832/1864 Reference Manual

• Violate, then restore zones

• Verify correct Reporting Codes are sent to the Central Station

Troubleshooting:

LCD Programmable-Message Keypad

•Press [✱][2] to view a trouble condition.

• The trouble light will flash and the LCD will display the first trouble condition present.

• Use the arrow keys to scroll through all trouble conditions present.

NOTE: When additional information is available for a specific trouble condition a [✱] will appear on the display.

Press the [✱] key to view the additional information

Appendix D: Troubleshooting Guide

LED Keypads, LCD Fixed Message Keypads

•Press [✱][2] to view a trouble condition.

• The trouble light will flash.

• Refer to the Trouble Summary chart below to determine the trou ble condition(s) present.

Trouble Summary:

Light [1]✱ Service Required - Press [1] for more information

[1] Low Battery [2] Bell Circuit [3] General System Trouble [4] General system Tamper [5] Module Supervision [6] RF Jam Detected [7] PC5204 Low Battery [8] PC5204 AC Failure

Light [2] AC Trouble

Light [3] Telephone Line Trouble

Light [4] Failure to Communicate

Light [5]✱ Zone Fault -Press [5] for more information

Light [6]✱ Zone Tamper - Press [6] for more information

Light [7]✱ Wireless Device Low Battery - Press [7] for more information

Light [8] Loss of Time or Date

Page 58

PowerSeries - PC1616/PC1832/PC1864

Trouble Cause Troubleshooting

Trouble [1] Service Required Press [1] to determine specific trouble

[1] Low Battery Main panel battery less than 11.1VDC

NOTE: This trouble condition will not clear until the battery voltage is 12.5VDC min., under load.

[2] Bell Circuit Bell+, Bell-...Open Circuit • Disconnect Bell-/Bell+ wire leads, measure resistance of wire

[3] General System T r ouble PC5204 Output#1 Open Circuit • If Output#1 is unused: Ensure that terminals O1, AUX are

PC5204 AUX • Verify voltage measured across AC input terminals is 16-18VAC.

Printer connected to PC5400 offline Verify printer operation (out of paper, paper jam etc.) T-Link Networ k Fault present

T-Link Receiver Trouble present T-Link Interface Trouble present

NOTE: If battery is new allow 1 Hr. for battery to charge.

• Verify voltage measured across AC terminals is 16-18 VAC. Replace transformer if required.

• Disconnect battery wire leads

• Verify battery charging voltage measured across battery leads

= 13.70 - 13.80 VDC.

• Connect battery, remove AC power

• Verify measured voltage across battery terminals is 12.5VDC

min.

leads.

• Open circuit indicates break in wiring or defective siren/bell

• Jumper Bell+, Bell- with 1K resistor (Brown, Black, Red)

• Verify trouble clears

jumpered with 1K resistor (Brown, Black, Red)

• If Output #1 is used: Disconnect wire leads from O1, AUX terminals, measure the resistance of the wire leads

• Open circuit indicates a break in the wiring

• Disconnect all connections to PC5204 AUX terminal.

• Verify AUX voltage is 13.70 - 13.80 VDC.

Refer to the T-Link TL150/250/350 Installation Manual for details.

[4] General System Tamper

[5] Module Supervision Panel does not communicate with mod-

[6] RF Jam Detected Wireless Receiver - excessive noise

[7] PC5204 Low Battery PC5204 battery less than 11.5VDC

[8] PC5204 AC Failure No AC at PC5204 AC inputs Verify voltage measured across AC terminals is 16-18VAC.

Tamper input on module(s) open circuit Short tamper terminal to COM terminal on unused modules connected

ule(s) on KEYBUS

Keypad assigned to incorrect slot.

detected.

NOTE: This trouble condition will not clear until the battery voltage is 12.5VDC min., under load.

to KEYBUS (PC5100, PC5108, PC5200, PC5204, PC5208, PC5320, PC5400, PC5700).

Modules are immediately enrolled and supervised when detected on the KEYBUS. If a module has been remov ed, or if the slot assignment of a keypad has been changed, module supervision must be reset.

• View the event buffer (via DLS or LCD5500 keypad) to identify the specific module(s) in trouble

• To reset module supervision:

• Enter Program Section [902].

•Press [#] (wait 1 minute for panel to scan KEYBUS).

• Enter Program Section [903] to identify modules connected to the KEYBUS.

Check for external 433MHZ signal sources To disable RF Jam: enable Option [7] in program section [804] subsection [90].

See [1] Low Battery above

Replace transformer if required.

Page 59

Appendix D: Troubleshooting Guide

Trouble Cause Troubleshooting

Trouble [2] AC Failure

No AC at panel AC input terminals

Trouble [3] Telephone Line Trouble

Phone Line Voltage at TIP, RING on main panel less than 3VDC

Trouble [4] Failure to Communicate

Panel fails to communicate one or more events to central station

Verify voltage measured across AC terminals is 16-18VAC. Replace transformer if required.

• Measure the voltage across TIP and RING on the panel:

• No phone off-hook – 50VDC (approx)

• Any phone off-hook – 5VDC (approx)

• Wire incoming line directly to TIP and RING.

• If trouble clears, check wiring or the RJ-31 phone jack.

Connect a headset to TIP and RING of the control panel. Monitor for the following conditions:

• Continuous dial tone

• Reverse TIP and RING

• Recorded operator message comes on

• Verify correct phone number is programmed

• Dial the number programmed using a regular telephone to determine if a [9] must be dialed or if 800 service is blocked.

• Panel does not respond to handshakes.

• Verify the format programmed is supported by the central station.

• Panel transmits data multiple times without receiving a handshake

• Verify that the account number and reporting codes are cor-

rectly programmed.

NOTE: Contact ID and Pulse formats

• Program a HEX [A] to transmit a digit [0]

SIA format

• Program a digit [0] to transmit a digit [0]

Trouble [5] Zone Fault Press [5] to determine specific zones with a fault trouble

Open circuit is present on one or more fire zones on the main panel or zone expander

An open circuit is present on PGM2 being used as a 2-wire smoke detector input

• Ensure fire zones have a 5.6K resistor (Green, Blue, Red) connected.

• Remove the wire leads from Z and COM terminals and measure the resistance of the wire leads.

• An open circuit indicates a break in the wiring or resistor not

connected.

• Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals. Verify the trouble condition clears.

• Ensure the correct 2.2K end-of-line resistor is connected (Red, Red, Red).

• Remove the wire leads from PGM2 and AUX+ terminals and measure the resistance of the wire leads.

• An open circuit indicates a break in the wiring or no resistor

connected.

• Connect a 2.2K resistor (Red, Red, Red) across the PGM2 and AUX+ terminals. Verify the trouble condition clears.

Page 60

PowerSeries - PC1616/PC1832/PC1864

Trouble Cause Troubleshooting

Trouble [5] Zone Fault (Cont.)

One or more wireless devices have not checked in within the programmed time

A short circuit is present on one or more zones with double end-of-line resistors enabled

• If the trouble occurs immediately, a conflict with a hard wired zone exists:

• The zone being used is already assigned to a PC5108 zone

expander

• The zone being used is assigned as a keypad zone

• Perform a Module Placement Test – Program Section [904] and verify the wireless device is in a good location.

• If bad test results occur, test the wireless device in another

location

• If the wireless device now tests good, the original mounting

location is bad

• If the wireless device continues to give bad test results

replace the wireless device

• Remove the wire leads from Z and COM terminals and measure the resistance of the wire leads.

• A short circuit indicates a short in the wiring.

• Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals.

• Verify the trouble condition clears.

Trouble [6] Zone Tamper Press [6] to determine specific zones with a tamper trouble

A tamper condition is present on one or more wireless devices

An open circuit is present on one or more zones with double end-of-line resistors enabled

• Perform a Module Placement Test –Section [904]

• Violate, then restore the tamper:

• If no test result then replace wireless device

• Remove the wire leads from Z and COM terminals.

• Measure the resistance of the wire leads.

• Open circuit indicates a break in the wiring.

• Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals.

• Verify the trouble condition clears.

Trouble [7] Wireless Device Low Battery Press [7] to toggle through specific devices with low battery trouble

1st press

– Wireless Zones

2nd press

– Handheld Keypads 3rd press – Wireless Keys

One or more wireless devices has a low battery

NOTE: The event will not be logged to the event buffer until the wireless device low battery delay time expires

• Program Section [377] Opt 9

Replace battery

NOTE: Replacing batteries will cause a tamper. Replacing cover will restore the tamper causing the associated reporting codes to be sent to the Central Station.

Trouble [8] Loss of Clock/Date

The main panel internal clock is not set To program the time and date:

• Enter [✱][6][Master Code] then Press [1]

• Enter the time and date (in military) using the following format:

HH:MM MM/DD/YY

Example.

For 6:00 pm, June 29, 2005 Enter: [18] [00] [06] [29] [05]

IMPORTANT!

Ensure you have the following information available before contacting Customer Support

- Control Panel Type and Version, (e.g., PC1864 v4.1)

NOTE: Version n umber can be accessed by e ntering [

✱][Installer Code][900] on any LCD keypad. This informa-

tion is also located on a sticker on the Printed Circuit Board.

- List of modules connected to Control Panel, (e.g., PC5400, PC5204 etc.)

Page 61

NOTES

Page 62

NOTES

Page 63

Note to Installers

This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be:

• Inadequate Installation

A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient strength and construction to provide the le v el of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available.

• Criminal Knowledge

This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected.

• Access by Intruders

Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system.

• Power Failure

Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC po wer, any interruption, however brief, will render that device inoperati ve while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.

• Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will keep the system in good operating condition.

• Compromise of Radio Frequency (Wireless) Devices

Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent radio signal interference.

• System Users

A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm.

• Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there i s insufficient warning to allow all occupants to escape in time to avoid injury or death.

• Motion Detectors

Motion detectors can only detect motion within the designated areas as shown in th eir respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have multip le beams of det ection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation. Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on.

• Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person.

• Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect.

• Insufficient Time

There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings.

• Component Failure

Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component.

• Inadequate Testing

Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of the system.

• Security and Insurance

Regardless of its capabilities, an alarm system is not a substitut e for property or life insuranc e. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an emergency s itua tion.

Limited Warranty

Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty period. There is absolutely no warranty on software and all software products are sold as a user license under the terms of the software license agreement included with the product. The Customer assumes all responsibility for the proper selection, installation, operation and maintenance of any products purchased from DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.

International Warranty

The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:

• damage incurred in shipping or handling;

• damage caused by disaster such as fire, flood, wind, earthquake or lightning;

• damage due to causes beyond the control of Digital Security Controls such as excessive voltage,

mechanical shock or water damage;

• damage caused by unauthorized attachment, alterations, modifications or foreign objects;

• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls

Ltd.);

• defects caused by failure to provide a suitable installation environment for the products;

• damage caused by use of the products for purposes other than those for which it was designed;

• damage from improper maintenance;

• damage arising out of any other abuse, mishandling or improper application of the products.

Items Not Covered by Warranty

In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii) products which are not identified with DSC's product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid purchase order is received from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.

Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser’s time, the claims of third parties, including customers, and injury to property. The laws of some jurisdictions limit or do not allow the disclaimer of conse quential damages. If the la ws of such a jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that the above may not apply to you.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are gov erned by the laws of the province of Ontario, Canada.

WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

Out of Warranty Repairs

Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.

Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital Security Controls has predetermined and which may be revised from time to time, will be charged for each unit repaired.

Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of the replacement product will be charged for each replacement unit.

Page 64

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this number must be provided to the Telephone Company. PC1864 Product Identifier US: F53AL01BPC1864 PC1832 Product Identifier US: F53AL01BPC1832 PC1616 Product Identifier US: F53AL01BPC1614 REN: 0.1B USOC Jack: RJ-31X

Telephone Connection Requirements

Ringer Equivalence Number (REN)

Incidence of Harm

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone

Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

Equipment Maintenance Facility

Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.

Network Service

Provider's

Facilities

Telephone

Network

Demarcation

Customer Premises Equipment and Wiring

RJ-31X

Jack

Alarm Dialing

Equipment

Line

Point

Telephone

Answering

System

Unused

RJ-11 Jack

Fax Machine

Telephone

Computer

Unused

RJ-11 Jack

Telephone

INDUSTRY CANADA STATEMENT

NOTICE: This Equipment meets the applicable Industry Canada Terminal Equipment Tech-

nical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that that Industry Canada approved the equipment

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed five.

PC1616 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1614

PC1832 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1832

PC1864 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . . IC: 160A-PC1864

29007317R002

DSC PC1832, PC1616, PC1864 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual