Dsc PC1808 User Manual

PowerSeries

PC1616/PC1808/PC1832/PC1864 version 4.2 S.Africa

Installation Guide

WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability the manufacturer. The entire manual should be carefully read.

Table of Contents

Section Description Page

1

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

2

2.1

2.2

2.3

2.4

2.5

3

3.1

3.2

3.2.1

3.2.2

3.3

3.3.1

3.3.2

3.3.3

3.3.4

Installation & Wiring............................................................................................1

Keybus Wiring ..................................................................................................2

Zone Wiring......................................................................................................2

Zone Expanders...............................................................................................2

Bell Wiring ........................................................................................................ 2

AUX Power Wiring............................................................................................4

PGM Wiring......................................................................................................4

Telephone Line Wiring...................................................................................... 4

Ground .............................................................................................................4

Battery..............................................................................................................4

AC Wiring .........................................................................................................4

User Commands .................................................................................................. 5

Away Arming ....................................................................................................5

Stay Arming...................................................................................................... 5

Disarming ......................................................................................................... 5

[] Commands.................................................................................................5

Function keys ................................................................................................... 7

Programming ....................................................................................................... 8

Template Programming ....................................................................................8

DLS Programming............................................................................................ 8

Local Programming .......................................................................................... 8

Remote Programming (via telephone line)....................................................... 8

Advanced Keypad Programming...................................................................... 8

Programming Toggle Options........................................................................... 9

Programming Decimal & Hexadecimal Data....................................................9

How to Exit Programming.................................................................................9

Viewing Programming ...................................................................................... 9

4 Programming Descriptions...............................................................................10

5 Programming Worksheets ................................................................................27

6 For the Record ................................................................................................... 52

7 Zone Programming Summary ..........................................................................53

App A Reporting Code Formats (Contact ID, SIA) .............................................. APP A

App B Troubleshooting Guide ..............................................................................APP B

App C Template Programming.............................................................................. APP C

Section 1: Installation & Wiring

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1808, PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.

All necessary information required to meet UL Listing requirements is included in this document.

Technical Summary

OUT Of THE BOX

Qty 1  Qty 1  Qty 1  Qty 1  Qty 2  Qty 1  Qty 4 

Qty 16 

Qty 1  Qty 1  Qty 1 

Cabinet PC Module Installation guide User manual Cabinet Label Cabinet Door Plug Standoffs

5.6KΩ Resistors

2.2KΩ Resistor

1.0KΩ Resistor Grounding Kit

SPECIFICATIONS

Temp Range ....................-0°C-49°C

Humidity (Max).................-93%R.H.

P.Supply.......16.5VAC/40VA @60Hz

Current Draw (Panel) 110mA (nom.) Aux+ Output .11.1-12.6VDC/500mA Bell Output ...11.1-12.6VDC/700mA

FEATURES

On-board Zones

Hardwired Zones 16 (1xPC5108) 8 32(3xPC5108) 64 (7xPC5108)

Wireless Zones

Keypad Zone Support

On-board PGMs PGM 1 - 50mA

PGM Expansion 8x50mA (PC5208)

Keypads

Partitions

User Codes 47 + Master Code 47 + Master Code 71 + Master Code 94 + Master Codes

Event Buffer 500 Events 500 Events 500 Events 500 Events

Transformer Required 16.5VAC/40VA 16.5VAC/40VA 16.5VAC/40VA 16.5VAC/40VA

Battery Required 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr

Bell Output 12V/700 mA (cont) 12V/700 mA (cont) 12V/700 mA (cont) 12V/700 mA (cont)

PC1616 PC1808 PC1832 PC1864

6

32

888

32 32 32



PGM 2 - 300mA

4x500mA (PC5204)

8

2

PGM 1, 3, 4 - 50mA PGM 2 - 300mA

8x50mA (PC5208) 4x500mA (PC5204)

888

848

PGM 1 - 50mA PGM 2 - 300mA

8x50mA (PC5208) 4x500mA (PC5204)

PGM 1, 3, 4 - 50mA PGM 2 - 300mA

8x50mA (PC5208) 4x500mA (PC5204)

COMPATIBLE DEVICES

Keypads (

PK5500 Keypad......................................................................125mA (max.)

PK5501 Keypad......................................................................125mA (max.)

PK5508 LED Keypad.............................................................. 125mA (max.)

PK5516 LED Keypad.............................................................. 125mA (max.)

LCD5511 Fixed Message LCD Keypad................................... 85mA (max.)

LED5511Z 8-zone LED Keypad ............................................100mA (max.)

RFK5500 Keypad ................................................................... 135mA (max.)

RFK5501 Keypad ................................................................... 135mA (max.)

RFK5508 Keypad ................................................................... 135mA (max.)

RFK5516 Keypad ................................................................... 135mA (max.)

PC5003C(removable door).................................................. 248x298x78mm

Model Power UC1 ............................................................315x 319x100mm

Refer to the Reference Manual for alternate control cabinets

Backward compatible with all PowerSeries keypads) Modules

T-Link TL150*/TL-250/TL300 ......................................... 275/350mA

PC5100 2-wire Interface .......... 40mA plus devices to 170mA max.

PC5132-433 Wireless Receiver ........................................... 125mA

RF5108-433 Wireless Receiver ........................................... 125mA

PC5108 Zone Expander ......................................................... 30mA

PC5200 Power Supply ............................................................ 20mA

PC5204 Power Supply with 4 Programmable Outputs .......... 30mA

PC5208 Low Current Programmable Output Module ............ 50mA

PC5400 Printer/DVAC Module ............................................... 65mA

Cabinets

PC5401 Bi-Directional RS232 Module (Not UL Listed) .......... 65mA

Escort5580 Telephone Interface Module ............................. 130mA

*The TL150 is not UL/ULC Listed

Refer to the Reference Manual for additional devices.

Installation

Begin the installation by mounting additional modules in the cabinet using the standoffs provided, then mount the cabinet in a dry protected area with access to unswitched AC power. Install Hardware in the sequence indicated in the following pages. Do NOT apply power until installation is complete.

All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4” (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections.

1

PowerSeries - PC1616/PC1808/PC1832/PC1864

CONTROL

PANEL

150’ (46m)

500’ (152m)

Burglary Zone Wiring Chart

Wire

Gauge

Maximum wire Length to

End-of-line Resistor

(feet/meters)

22 3000 / 914

20 4900 / 1493

19 6200 / 1889

18 7800 / 2377

Figures are based on maximum wiring

resistance of 100 Q

1.1 Keybus Wiring

The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEYBUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel.

The following rules must be followed when wiring the Keybus:

• Minimum 22 AWG wire, maximum 18 AWG (2-wire twisted preferred

•Do NOT use shielded wire

• Modules can be home run, connected in series or can be T-tapped provided that the maximum wire distance from the control panel to any module does not exceed 1,000 feet (305m)

• No more than 3,000 feet (915m) of wire can be used in total

1.2 Zone Wiring

Zones can be wired for Normally Open, Normally Closed Contacts with Single-end-of-line (SEOL) resistors or Double End-of-Line (DEOL) resistors. Observe the following guidelines

•For UL Listed Installations use SEOL or DEOL only.

• Minimum 22 AWG wire, maximum 18 AWG

•Do NOT use shielded wire

• Wire run resistance shall not exceed 100Ω. Refer to the chart below.

Normally Closed Loops - Do NOT use for UL Installations

Single End-of-Line Resistor Wiring

• Section [001]-[004] Selects Zone Definition

• Section [013] Opt [1] Selects Normally Closed or EOL resistors

• Section [013] Opt [2] Selects Single EOL or Double EOL resistors.

• Section [101]-[108] Opt [14], [15], [16] Selects Normally Closed Single EOL or Double EOL for on-board zones (Zone 1-8)

Zone Status - Loop Resistance/Loop Status

• Fault - 0Ω (shorted wire/loop)

• Secure - 5600Ω (contact closed)

1.3 Zone Expanders

Zone expanders add zones in groups of eight to the Alarm system. Module jumpers J1,J2,J3 are required to assign zones to these modules. Jumper settings for PC5108v2 are shown here.

• PC5108v1.0 supports first 32 zones only.

• PC5700 enrolls as two modules

• Do NOT use PC5108v1 &v2 on the same

panel.0

1.4 Bell Wiring

These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6 VDC for residential installations (e.g.DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern requirements: Program Section [013] Opt [8] ON.

NOTE: Steady, Pulsed alarms are also suppor ted.

The Bell output is supervised and power limited by 2A PTC. If unused, connect a 1000Ω resistor across Bell+ and Bell- to prevent the panel from displaying a trouble. See [][2].

2

Module Zones Jumpers J1 J2 J3

ON ON ON Zones Disabled OFF ON ON Zones 09-16 ON OFF ON Zones 17-24 OFF OFF ON Zones 25-32 ON ON OFF Zones 33-40 OFF ON OFF Zones 41-48 ON OFF OFF Zones 49-56 OFF OFF OFF Zones 57-64

Assigned

Double End-of-Line Resistor Wiring

• Tamper - infinite (broken wire, open)

• Violated - 11,200Ω (contact open)

Refer to to the associated installation sheet for Jumper locations for the PC5108v1, or PC5700

PC1616/1808/1832/1864 Wiring Diagram

220

1. Inser t Stand off into cabinet mounting hole in the desired location. Snap-inplace .

2. P osition circuit board mounting holes ov er standoffs . Press fir mly on board to snap-in-place .

PC Boar d

Cabinet

Stand Of f

Pr imar y:120V A C/60Hz. Secondar y: 16.5VDC 40V A DSCPTD 1640U Class II Tr ansf or mer

NO TE: Do not connect transf or mer to receptacle controlled by a s witch

PO WER LIMITED

Cab le Tie (not supplied) recommended

UA 50 3

220

PC1616/1808/1832/1864

W ARNING:

High V oltage .D isconnect AC Po wer

and telephone lines bef ore servicing

DSC

AC

230 V /50 Hz International

CON1

BA T+BA T-

AC AC

To EGND

AC

16.5V /40V A

FUSE

Te r m inal

IMPOR T ANT :

a)This equipment, Alar m Controller PC1808/1616/1832/1864 shall

be installed and used within an en vironment that pr ov ides th e

pollution degree max 2 and ov er vo ltages categor y II NON-HAZARDOUS LOCA TIONS , indoor onl y. The equipment is FIXED and PERMANENTL Y connected and is designed to be installed by ser vice persons only; [ser vice person is defined person ha ving the appropr iate technical training and e xper ience necessar y to be aw are of hazards to which that person ma y be e xposed in per fo rm ing a task and of measures to minimi ze the ri sks to that person or other persons .]

b)The connection to the mains supply must be made as per the local

s ru les and regulations.

author itie An appropr iate disconnect de vice must be pr ov ided as par t of th e bu ilding installation. Where it is not possi bl e to rely on identification of

the neutral in the AC Mains supply the disconnecting device must disconnect both poles simultaneously (line and neutral). The device shall disconnect the supply du

c)The equipment enclosure must be secured to the bu ilding str uctur e

bef ore operation.

e)Inter nal wi ri ng must be routed in a manner that pr ev ents:

- Excessi ve strain on wire and on te rm inal connections;

- Loosening of te rm inal; connections;

- Damage of conductor insulatio n

f) Disposal of the used batte

reco ve ry and recycling regulations applicab le to the intended mar k et.

ri es shall be made according to the w ast e

ring servicing.

g) Before servicing, DISCONNECT the telephone connection.

W ARNING:

High V oltage . Disconnect AC Po wer

and telephone lines bef ore servicing

as a

PC1808 PC1864

CON1

BA T+BA T-

AU X+ BELL +

AC AC RED BL KY EL GRN Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8

AU X- BELL-

PGM1 PGM3

PGM2 PGM4

On ly

PC1808 PC1832

864

PC1

Only

RING R- 1

EGND

TI PT -1

See Section 9 f or ground wir ing details

TB-2

12V / 7 AHr 12V / 7 AHr

BLA CK

RE D

NON-PO WER LIMITED

W ARNING:

Incorrect connections may result in PTC failure or improper operation.

DSC Model BD7-12

or equiv alent

Batter y

Standb yTime:

24H rs min.

Inspect wiring and ensure connections are correct be fo re appl ying po we r.

Incorrect connection of batteries ma y result in batter y rupture or Fire Hazar d. Do NO T allo w metal objects to connect the Positive and Negative Terminals. Ensure that batteries are connected with correct polarity [Red to (+), Blac k to (-)]. F ailure to compl y with this ma y result in batte ry rupture and/or Fire Hazar d.

Do NO T r oute an y wiring o ver cir cuit boar ds .M aintain at least 1"(25.4mm) separation. A minim um of 1/4" (6.4mm) separation mu st be maintained at all points between po wer limited wiring and all other non-po wer limited wiring.

220

REV XX

U A503

PC1616/1808/1832/1864

DSC

PC-LIN K

AUX+ and Keybus (Red) are Internally Connected To ta l current draw from Keyp ads, PG MO utput s and Aux circuit sm ust not exceed 550mA.

Internally Connected

10

PC1808 PC1864

CON1

BA T+BA T-

A UX+ BELL+

AC AC RED BLK YEL GRN Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8

A UX- BELL-

9 8 4 3 1

PGM1 PGM3

PGM2 PGM4

5

On ly

2

See corresponding Section NumberT ex t fo r wi ri ng details .

PC1808

PC1832 PC1864

Onl y

EGND

7

RING R- 1

TI PT -1

6

TB-2

3

PowerSeries - PC1616/PC1808/PC1832/PC1864

RM-1/RM-2 POWER LOOP

SUPERVISORY RELAY

T-1

R-1

TIP

RING

RJ-31X

Tighten nut to break paint and make

good connection to the cabinet

1.5 AUX Power Wiring

The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc. If the total current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below.

Min/max operating voltages for devices, sensors and modules is 9.5V

DC - 14VDC

Refer to the list of Compatible Devices on page 1 and/or the Reference Manual for the current draw of individual devices

1.6 PGM Wiring

PGMs switch to ground when activated by control panel. Connect the positive side of the device to be activated to the AUX+ Terminal. Connect the negative terminal to the PGM. current output is as follows

• PGM 1, 3, 4.... ............................................. .............................. 50mA

• PGM 2...... ............................................ ................................... 300mA

2-wire Smoke Detectors Initiating Circuit

• Style B (Class B), Supervised, Power Limited

• UL Compatibility Identifier.................................................... PC18-1

• DC Output Voltage..... ...................................................9.8-13.8 VDC

• Detector Load ........... ............................................ ........ 2mA (MAX)

• Single-end-of-line (SEOL) Resistor ........................................2200Ω

• Loop Resistance .............................................................. 24Ω (MAX)

• Standby Impedance.....................................................1020Ω (ΝΟΜ)

• Alarm Impedance................................................... .......570Ω (MAX)

• Alarm Current....................... ....................................... 89mA (MAX)

For currents levels greater than 300mA a relay is required. PGM2 can also be used for 2-wire smoke detectors.

NOTE: Use SEOL resistors on Fire Zones ONLY.

PGM 1, LED output with current limiting resistor and Optional Relay driver output

UL Compatibility ID For FSA-210B Series is: FS200

NOTE: For ULC Listed installations use FSA-210A and FSA-410A series

1.7 Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ31x Connector as indicated. Use 26 AWG wire minimum for wiring.

For connection of multiple devices to the telephone line, wire in the sequence indicated. Telephone format is programmed in section [350]. Telephone Call Directions are programmed in section [351]-[376].

1.8 Ground 1.9 Battery 1 . 1 0 A C W i r i n g

Ground Installation A sealed, rechargeable, lead acid

NOTE: Do not connect transformer to a receptacle controlled by a switch. (UL Listed Installations Only)

battery or gel type battery is required to meet UL requirements for power standby times. NOTE: UL Residential/Commercial Burglary installations require 4Hrs Power Standby time. NOTE: UL/ULC Residential Fire & Health Care installations require 24 Hr. power standby. ULC Commercial Burglary and Fire monitoring installations require 24 Hr. power standby.

4-wire Smoke Detectors

Standby Battery Guide

Battery Charging Current: 400 mA

Batt Standby Size 4Hr 24Hr

-------------------------------------------------

4Ahr 700mA --- 7Ahr 700mA 180mA 14Ahr 700mA 470mA

NOTE: Battery capacity will deteriorate with age and number of charge/discharge cycles. Replace every 3-5 years.

AC Wiring

UL Listed Installations

Primary: 120VAC/

60Hz./0.33A

Secondary:

16.5VAC/40VA DSC PTD 1640U Class 2 Transformer.

4

Section 2: User Commands

Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section describes basic keypad commands. Refer to the PC1616/1832/1864 Reference Manual for detailed description of all keypad commands.

Press the

Section 2.1 – Away Arming

The Ready light must be ON to arm the system. If the Ready light is OFF, ensure all protected doors and windows are secure or bypassed. To arm the system in the Away mode, either press and hold the Away function button for 2 seconds or enter a valid user code and leave the premises through a door programmed as Delay. Upon arming, the Armed light will turn ON. If a user code was used to arm the system and Stay/Away zones are programmed, the Bypass light will turn ON and will turn OFF when a door programmed as Delay is violated. If the Audible Exit Delay option is enabled, the keypad will beep once every second during the exit delay (and three times a second during the last 10 seconds) to alert the user to leave.

Section 2.2 – Stay Arming

The Ready light must be ON to arm the system. If the Ready light is OFF ensure all protected doors and windows are secure or bypassed. To arm the system in the S tay mode, either press and hold the S tay function button for 2 seconds or enter a valid user code and stay within the premises (do NOT violate a door programmed as Delay). Upon arming, the Armed light and Bypass light will turn ON. If the Stay function button is used, the keypad will not beep during the exit delay. If a user code was used, the keypad will beep if the Audi ble Exit De lay option is enabled.

Section 2.3 – Disarming

The user must enter through a door programmed as Delay. Upon entering, the keypad will emit a steady tone (and emit a pulsing tone during the last 10 seconds of entry delay) to alert the user to disarm the system. Enter a valid user code to disarm the system. If an alarm occurred while the panel was armed, the Memory light and the zones that went into alarm will be flashing (LED keypad) or the keypad will display ‘Alarm in Memory’ (LCD keypad). Press the [#] key to return the keypad to the Ready state.

[#] key to reset the keypad if an error has been made entering user codes or keypad commands.

Section 2.4 – [] Commands

The following is a list of the [] commands available and a description of each:

[][1] Bypass (disarmed state)/Reactivate Stay/Away Zones (armed state) [][2] Display Trouble Conditions [][3] Display Alarm Memory [][4] Door Chime Enable/Disable [][5] User Code Programming [][6] User Commands [][7][x] Command Functions 1 – 4 [][8] Installer Programming [][9][code] No-Entry Arming [][0] Quick Arm (disarmed state)/Quick Exit (armed state)

[][1] Bypass/Re-activate Stay/Away Zones

LED Keypad:

Press [][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The Bypass light will flash. The keypad will turn ON the corresponding zone light to indicate a zone is bypassed. To bypass or un bypass a zone, enter th e 2-d igit zone number. Once the correct zones are bypassed, press [#] to exit. The Bypass light will be ON if any zones are manually bypassed.

LCD Keypad:

Press [][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The keypad will display ‘Scroll to View Zo nes’. The keypad wi ll display the programmed zon e labels for the zones and include the letter ‘O’ in the bottom, righ t corner if the zone is violated or the letter ‘B’ if the zone is bypassed. Scroll to the appropriate zone and press the [] key to change the bypass status (or enter the 2-digit zone number). Once the correct zones are bypassed, press [#] to exit.

Additional Bypass Commands:

Bypass Recall: Press [99]. The keypad will recall the last group of zones that were bypassed Clear Bypass: Press [00]. The keypad will clear the bypass on all zones. Save Bypass: Press [95]. The keypad will save which zones are manually bypassed. Recall Save: Press [91]. The keypad will recall the bypassed zones that were saved.

Hold Up Zones cannot be assigned to bypass groups.

Re-activate Stay/Away Zones:

Press [][1] when the system is armed in the Stay mode to change the armed status to Away mode. The system will add the Stay/Away zones back into the system after the exit delay time expires.

5

PowerSeries - PC1616/PC1808/PC1832/PC1864

[][2] Trouble Display

Refer to Appendix D – Trouble Conditions, for troubleshooting assistance and a detailed description of all trouble conditions.

Press [8] on any keypad or [] on the trouble on any PK series keypad to enter the time and date programming menu. This option will be available if a Loss of Clock trouble is present on the system. A General System Supervisory caused by a hardwired or wireless zone expander cannot be overidden by this method. If Section [701] option 3 is ON arming will be inhibited if a system low battery or AC trouble is detected and cannot be overridden by this method.

[][3] Alarm Memory Display

The Memory light will be ON if an alarm occurred during the last armed period. Press [][3]. The Memory light will flash and the keypad will display the zones that went into alarm.

: To clear the Memory light, arm then disarm the system.

[][4] – Door Chime Enable/Disable

Press [][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled. The same function can be performed by pressing and holding the Chime function button for 2 seconds.

[][5] – Program User Codes

The following table identifies available user codes:

Code

[01]-[39], [41]-[95] [40]

Type Function

General User Codes arm, disarm

Master Code all functions

Programming User Codes:

LED Keypad:

Press [][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone lights to indicate if any user codes are programmed. To add or change a user code, enter the 2-digit user code to be programmed. The zone light will flash. Enter a new 4 or 6-digit user code or press [] to delete the user code. After the user code is programmed or deleted, the zone light corresponding to the user code will stop flashing. T o add or change another user code, enter the 2-digit user cod e to be programmed or press [#] to exit.

LCD Keypad:

Press [][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right corner if the user code is programmed. Scroll to the appropriate user and press the [] key to program the user (or enter the 2-digit user number). Enter a new 4 or 6-digit user code or press [] to delete the user code. After the user code is programmed or deleted, scroll to another user or press [#] to exit.

Programming Partition Assignment:

Press [][5] followed by the Master Code or Supervisor Code. Press [98] followed by the 2-digit user to change to the partition assignment. The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is ON, the user is assigned to partition 1. T o change the partition assignment, press the number co rresponding to th e partition. Once the correc t partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [98] followed by the 2-digit user number. When finished, press [#] to exit.

Programming User Attributes:

Press [][5] followed by the Master Code or Supervisor Code. Press [99] followed by the 2-digit user to change to the user attributes. The keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.

Light [1] User can enter User Code Programming section with this code Light [2] Duress Reporting Code is sent whenever this code is entered Light [3] User can manually bypass zones Light [4] User can access the Escort5580 module remotely Light [5] For Future Use Light [6] For Future Use Light [7] The panel will squawk the bell output when the user arms/disarms Light [8] One-time use code – Can disarm the system once per day and is reset at midnight.

To ch ange the user attributes, press the number corresponding to the attribute. Once the correc t attributes are as signed to the user, press [#] to exit. To change the user attributes for another user, press [99] followed by the 2-digit user number. When finished, press [#] to exit.

6

Section 2: User Commands

[][6] – User Functions

Press [][6] followed by the Master Code, then press the number corresponding to the following functions.

[1] Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time using

military standard (e.g., 8:00 pm = 20:00 hours).

[2] Auto-arm/Auto-disarm Enable/Disable: The keypad will emit 3 rapid beeps if the Auto-arm/Auto-disarm feature is now enabled

and a steady 2-second tone if it is now disabled.

[3] Auto-arm Time/Day: Press the number corresponding to the day of the week (1=Sunday, 2=Monday etc.) followed by the auto-

arm time (HH:MM). Program the time using military standard (e.g., 8:00 pm = 20:00 hours).

[4] System Test: The panel will perform the following; activate the bell output, keypad buzzer and all keypad status lights for 2

seconds, test the backup battery and transmit a reporting code to the central station (if programmed).

[5] Enable DLS: The panel will temporarily enable DLS for 1 or 6 hours depending on programming (see Sect [701] opt.[7]). [6] User Initiated DLS: The panel will attempt to call the DLS computer. [7] For Future Use [8] For Future Use

For LCD Keypads: Scroll to the desired option then press []

Additional Alphanumeric Keypad Functions:

When scrolling through the list of available functions, the following additional functions are available:

Event Buffer: Used to view the 500-event panel buffer Brightness Control: Used to adjust the display backlighting level for optimal viewing Contrast Control: Used to adjust the display contrast level for optimal viewing Buzzer Control: Used to adjust the keypad buzzer tone for optimal sound

[][7][x] – Command Output (1-4)

Press [][7][x]. If the Command Output Code Required option is enabled, enter a valid user code. The panel will activ ate any PGM output assigned to the command output.

[][8] – Installer Programming

Press [][8] followed by the Installer Code to enter Installer Programming. Refer to the ‘How to Program’ section for more information.

[][9][User Code] – No-Entry Arming

Press [][9] followed by a valid user code. The system will arm in the S tay mode and after the e xit delay expires, it will remove entry delay. All zones programmed as Delay will function like Instant zones. The system will flash the Armed light to indicate that the system is armed with no entry delay.

[][0] – Quick Arm/Quick Exit

Quick Arm: When disarmed, press [][0] to arm the system. The system will arm as if a valid user code was entered. Quick Exit: When armed, press [

during the following 2 minute time period without changing the status of the system.

][0] to activate Quick Exit. The system will allow a single zone programmed as Delay to be violated once

Section 2.5 – Function Keys

Keypads have 5 programmable one-touch function buttons located in a column down the right-side of the keypad. These buttons can also be activated by pressing and holding number [1] through [5] respectively for 2 seconds. The default for these function buttons on the PK series keypads are as follows:

[1] Stay Arm [4] Fire Reset – Command Output 2 [2] Away Arm [5] Quick Exit [3] Chime Enable/Disa b le

7

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section 3: Programming

This section provides the information necessary to program all required features for a basic system as well as common applications. Refer to the PC1616/1832/1864 Reference Manual for a complete description of all programmable features.

3.1 Template Programming

Selecting [][8] [Installer Code] [899] displays the current 5 digit template programming code. Refer to Appendix C - Template Program- ming for a detailed description of available templates and corresponding 5 digit codes. After entering a valid 5 digit template programming

code, you will be prompted to enter the following in the sequence indicated below:

This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.

1. Central Station Telephone Number, enter 32 Character Telephone number

Program the required Central Station phone number. Press [#] to complete your entry if less than 32 digits. This phone number will be entered into programming section [301].

2. Central Station Account Code, enter 6-digit code

Program the required Central Station Account Code. Press [#] to complete your entry if less than 6 digits. This account code will be entered into programming section [310].

3. Partition Account Code, enter 4-digit code

This programming section will only be prompted if Contact ID has been selected as a communications format. Program the required Partition Account Code. This Partition account code will be entered into programming section [311].

4. DLS Access Code, enter 6-digit code

Program the required DLS Access Code. Press [#] to complete your entry if less than 6 digits. This Access Code will be entered into programming section [403].

5. Partition 1 Entry Delay 1, Partition 1 Exit Delay, enter each 3-digit delay time

Program the desired 3 digit Partition 1 Entry Delay (in seconds) followed by the desired 3 digit Partition 1 Exit Delay (in seconds). These values will be entered in programming section [005] sub-section [01] entry 1 and 3 respectively.

6. Installers Code Enter the required 4 or 6 digit access code installers access code (dependent on Section [701] option 5). This Installer Access Code will be

entered into programming section [006]. After the Installers Code has been programmed the keypad will return to base installers programming menu.

All template programming information must be re-entered after performing a hardware or software panel default.

3.2 DLS Programming

3.2.1 Local Programming:

Follow the steps below in the sequence indicated to set up local programming using DLS:

1. Initiate downloading using the DLS software

2. Connect an RS-232 to PC-Link Cable between the Computer with DLS Software installed and the alarm panel to be programmed.

Connecting the DLS PC to the panel will automatically initiate the connection.

3.2.2 Remote Programming (via telephone line):

Refer to Section [400] block on page 21 for details.

The panel battery voltage can be monitored with DLS software. After the panel information has uploaded, battery voltage can be viewed in the DLS session window.

3.3 Advanced Keypad Programming

DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This will reduce the time required to program and will help eliminate errors.

To enter Installer Programming press [][8][Installer Code]. The Program light will FLASH (programmable LCD keypad displays will change to ‘Enter Section’). An error tone indicates the installer code entered is incorrect, Press [#] to clear any key presses and try again.

The default Installer Code is [5555].

8

The Armed and Ready lights indicate programming status:

Armed Light ON Panel waiting for 3-digit section number

If in module programming, waiting for section # to be entered.

Ready Light ON Panel waiting for data to be entered Ready Light FLASHING Panel waiting for HEX data to be entered

You cannot enter installer programming while the system or any partition is armed or in alarm.

3.3.1 Programming Toggle Options:

Enter the 3-digit programming section number.:

Section 3: Programming

• The Armed light will turn OFF and

• The Ready light will turn ON.

• The keypad will display which toggle options are ON or OFF according to the chart.

• To toggle an option ON or OFF, press the corresponding number on the keypad. The display will change accordingly.

Keypad Type

LED

Fixed-Message LCD Indicator # ON Indicator # OFF

Programmable-Message LCD # Displayed Dash [-] Displayed

Option ON Option OFF

Zone Light ON Zone Light OFF

• When all the toggle options are configured correctly, press the [#] key to exit the program section.

• The Ready light will turn OFF and the Armed light will turn ON.

3.3.2 Programming Decimal and Hexadecimal (HEX) Data:

• Enter the 3-digit programming section number.

• The Armed light will turn OFF and The Ready light will turn ON.

• Enter the data written in the boxes. For sections that require multiple 2 or 3 digit numbers, the keypad will double-beep after each 2 or 3 digit entry and move to the next item in

the list. After the last digit in the section is entered, the keypad will beep rapidl y 5 times and exit the program section. The Ready light will turn OFF and the Armed light will turn ON.

For sections that do not require data for every box (such as phone numbers) press the [#] key to exit the program section afte r entering all the required data. The Ready light will turn OFF and the Armed light will turn ON.

At any time the [#] can be pressed to exit any program section. All changes made up to that point will be saved.

Value Enter Telephone Dialer

HEX (or hexadecimal) digits are sometimes required. To enter a HEX digit, press

] key to begin HEX programming. The Ready light will FLASH. Refer to the

the [ chart below and press the number corresponding to the HEX digit required. The Ready light will continue to FLASH. Press [

] again to return to normal decimal

programming. The Ready light will turn ON.

HEX [A] HEX [B] HEX [C] HEX [D] HEX [E] HEX [F]

Press [][1][] Press [][2][] Press [][3][] Press [][4][] Press [][5][] Press [][6][]

Not Supported Simulated [] key Simulated [#] key Dial tone search Two second pause End of Number

In addition to the standard digits 0-9, HEX digits and special dialer functions can also be programmed if required.

3.3.3 How to Exit Installer Programming:

To exit installer programming, press the [#] key when the panel is waiting for a 3-digit section number (the Armed light is ON).

3.3.4 Viewing Programming

LED and LCD5501Z Keypads

Any programming section can be viewed from an LED or LCD5501Z

keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section.

The keypad displays the information using a binary format, according to

the following chart:

Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to

the next digit.

When all the digits in a section have been viewed, the panel will exit the section: the Ready light will turn OFF, and the Armed light

will turn ON, waiting for the next 3-digit programming section number to be entered.

Press the [#] key to exit the section

LCD Keypad

The keypad will immediately display all the information programmed wh en a programming section is entered. Use the arrow keys ( < >) to scroll through the data being displayed. Scroll past the end of the data displayed, or press the [#] key to exit the section.

9

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section 4 – Programming Descriptions

The following is a brief description of the features and options available in the Power PC1616/1832/1864 control panel. Refer to the PC1616/ 1832/1864 Reference Manual for a complete description of all programming features, li mitations and requirements.

Section [001] to [004] Zone Definitions

Option Description [00] Null Zone: Zone not used [01] Delay 1: When armed, provides entry delay when violated (follows Entry Delay 1) [02] Delay 2: When armed, provides entry delay when violated (follows Entry Delay 2) [03] Instant: When armed, instant alarm when violated [04] Interior: When armed, instant alarm if the zone is violated first, will follow entry delay if entry delay is active [05] Interior Stay/Away: Similar to ‘Interior’ except panel will auto-bypass the zone if Armed in the Stay mode [06] Delay Stay/Away: Similar to ‘Delay 1’ except panel will auto-bypass the zone if Armed in the Stay mode [07] Delayed 24-Hour Fire (Hardwire): Instant audible alarm when violated, communication delayed 30 seconds - if alarm

acknowledged during this time (by pressing a key), the alarm will be silenced 90 seconds and repeat cycle - if not, alarm will latch and communicate after 30 second delay

[08] Standard 24-Hour Fire (Hardwire): Instant alarm and communication when violated [09] 24-Hour Supervision (Hardwire): Instant alarm and communication when violated. Will not sound the bell or keypad buzzer. [10] 24-Hour Supervisory Buzzer: Instant alarm, panel will activate keypad buzzer instead of bell output [11] 24-Hour Burglary: Instant alarm when violated, audible alarm at default. Reporting code BA, BH [12] 24-Hour Hold-Up: Instant alarm when violated, silent alarm at default. Reporting code HA, HH [13] 24-Hour Gas: Instant alarm when violated, audible alarm at default. Reporting code GA, GH [14] 24-Hour Heat: Instant alarm when violated, audible alarm at default (also known as high-temp). Reporting code KA, KH [15] 24-Hour Medical: Instant alarm when violated, si lent alarm at default. Reporting code MA, MH [16] 24-Hour Panic: Instant alarm when violated, audible alarm at default. Reporting code PA, PH [17] 24-Hour Emergency: Instant alarm when violated, audible alarm at default. Reporting code QA, QH [18] 24-Hour Sprinkler: Instant alarm when violated, audib le alarm at default. Reporting code SA, SH [19] 24-Hour Water: Instant alarm when violated, audible alarm at default (also known as high water level). Reporting code WA, WH [20] 24-Hour Freeze: Instant alarm when violated, audible alarm at default (also known as low-temp). Reporting code ZA, ZH [21] 24-Hour Latching Tamper: Instant alarm when violated, panel cannot be armed until Installer Programming is entered [22] Momentary Keyswitch Arm: Arm or disarm the system when violated [23] Maintained Keyswitch Arm: Arm system when violated, disarm system when restored [24] For Future Use [25] Interior/Delay: Zone will function like an Interior zone when armed in Away mode, like a Delay zone when armed in the Stay

mode

[26] 24-Hour Non-Alarm: Zone will NOT create an alarm. Can be used with zone follower function for automation applications [29] Auto-Verified Fire: When violated, system will reset all smoke detectors for 20 seconds, then wait 10 seconds for detectors to

settle. If another fire alarm detected within 60 seconds zone will go into alarm immediately

[30] Supervisory: Instant alarm, system will activate keypad buzzer. A valid user code is required to silence Keypad buzzer. [31] Day Zone: Instant alarm when system is armed, keypad buzzer (no alarm) when system is disarmed [32] Instant Stay/Away: Similar to ‘Instant’ except panel will auto-bypass the zone if Armed in the Stay mode [35] 24-Hour Bell/Buzzer: Instant alarm when violated, system will activate bell output if armed, keypad buzzer if disarmed

10

Section 4 – Programming Descriptions

[36] 24-hr. Non-Latching Tamper Zone: Instant tamper condition when violated. Active in both the armed and disarmed state. [37]

[87] Delayed 24-Hour Fire (Wireless/Addressable): Same as Delayed 24-Hour Fire (Hardwire) but must be used for wireless or

[88] Standard 24-Hour Fire (Wireless/Addressable): Same as Standard 24-Hour Fire (Hardwire) but must be used for wireless or

Night Zone: Functions like Interior Stay/Away but will remain bypassed if the user presses [

when armed in the Stay mode

addressable smoke detectors

][1] to re-activate Stay/Away zones

Section [005] System Times

After entering Section [005], enter the 2-digit subsection number for the desired partition and program the Entry Delay 1, Entry Delay 2 and Exit Delay for each active partition on the system. Valid entries are from [001] to [255] (in seconds). Enter subsection [09] to program the Bell Cut-Off Time. Valid entries are from [001] to [255] (in minutes).

Section [006] Installer Code

The default Installer Code is [5555] or [555555] if 6-Digit Access Codes is enabled.

Section [007] Master Code

The default Master Code is [1234] or [123456] if 6-digit Access Codes is enabled.

Section [008] Maintenance Code

The default Maintenance Code is [AAAA] (not programmed). This code can arm any partition but cannot disarm unless the partition is in alarm.

Section [009] to [011] PGM Outputs

The PC1616 and PC1832 have two on-board PGM outputs (PGM1 and PGM2). The PC1864 has four on-board PGM outputs (PGM1 to PGM4). The panel has the capacity for up to 14 PGM outputs (8 additional low-current PGM outputs with PC5208 module, 4 additional high-current PGM outputs with a PC5204 module).

PGM Output Options:

Option Description

[00] For Future Use [01] Fire and Burglary: Output will activate (steady for burglary, pulsing for fire) if an alarm occurs on the selected partition [02] For Future Use [03] Sensor Reset: Output will normally be active and deactivate for 5 seconds when a [][7][2] fire reset command is entered or when an Auto-

Verify Fire alarm is detected

[04] 2-Wire Smoke: Configures PGM2 as 2-wire smoke detector input (PGM2 only) [05] Armed Status: Output will activate when all of the selected partitions are armed [06] Ready Status: Output will activate when all the selected partitions are in the Ready state (Ready light ON) [07] Keypad Buzzer Follow: Output will activate and follow the key pad buzzer for the selected partition when the following ev ents occur; entry

delay, door chime, audible exit delay, automatic arming pre-alert, 24-Hour Supervisory Buzzer zone alarm

[08] Courtesy Pulse: Output will activate during entry/e xit delay if the selected partition is armed – will remain active for an additional 2

minutes after the entry or exit delay expires

[09] System Trouble: Output will activate when any selected trouble condition is present [10] Latched System Event (Strobe): Output will activate when a selected condition occurs on any selected partition. Note output can be

programmed to follow timer

[11] System Tamper: Output will activate when any tamper condition is present [12] TLM and Alarm: Output will activate if a telephone line trouble is present and then an alarm occurs [13] Kissoff: Output will activate for 2 seconds when a valid kissoff is received from the central station [14] Ground Start: Output will activate for 2 seconds when the pan el attempts to seize the phone line (additional dial tone search must be

programmed in the central station phone number – HEX [D]) [15] Remote Operation: Output can be activated/deactivated via the DLS software [16] For Future Use [17] Away Armed Status: Activates when all of the selected partitions are armed in Away mode

11

PowerSeries - PC1616/PC1808/PC1832/PC1864

[18] Stay Armed Status: Activates when all of the selected partitions are armed in Stay mode [19] Command Output 1:Activates when a [][7][1] command is entered on the selected partition – Command can be programmed to require a

valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[20] Command Output 2: Activates when a [][7][2] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[21] Command Output 3: Activates when a [][7][3] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[22] Command Output 4: Activates when a [][7][4] command is entered on the selected partition – Command can be programmed to require

a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.

[23] Silent 24-Hour Input: Changes PGM to a 24-Hour Silent zone (PGM2 only) [24] Audible 24-Hour Input: Changes PGM to a 24-Hour Audible zone (PGM2 only)

[25] Delayed Fire and Burglary: Functions as a Fire and Burglary output but does not activate until the TX Delay time expires [26] Battery Test Output: Output activates for 10 seconds at midnight each day. [28] Holdup Output: Activates when a Holdup Alarm occurs on any assigned partition. Remains active until all assigned partitions have been

armed or disarmed. Will not activate if a Holdup Zone is goes into a fault or tamper condition.

[29] Zone Follower (Zones 1-8): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[30] Partition Status Alarm Memory: Activates if the selected partition is armed.

Output will pulse “one second ON / one second OFF if an alarm occurs

[31] Alternate Communicator: Activates when selected system event occurs. If active in the armed state, it remains active until the system is

disarmed. If activated in the disarmed state, it remains active until a valid access code is entered within bell cut-off time, or when the system is armed after bell cut-off time has expired.

[32] Open After Alarm: Actives for 5 seconds when system has been disarmed after an alarm.

[33] Bell Status and Programming Access Output: Activates when Bell, Installer programming mode or DLS is active. Remains active until

Bell is no longer active, Installer programming mode is exited and DLS programming is disconnected.

[34] Away Armed with no Zone Bypassed Status: Activates when armed with stay/away zones active and no zones bypassed.

[35] Zone Follower (Zones 9-16):

[36] Zone Follower (Zones 17-24): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[37] Zone Follower (Zones 25-32): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[38] Zone Follower (Zones 33-40): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[39] Zone Follower (Zones 41-48): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[40] Zone Follower (Zones 49-56): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

[41] Zone Follower (Zones 57-64): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

* See Section [501]-[514] Programmable Output Attributes, PGM Output Option [29] and [35]-[41] option 8 on page 23

Active when any of the selected zones are active and deactivates when all of the selected zones are restored.

Section [012] Keypad Lockout

The system can be programmed to ‘lockout’ keypads if a series of incorrect user or installer codes are entered. When lockout is active, all keypads emit a steady 2-second error tone when a key is pressed. Program the Number of Invalid Codes Before Lockout with the desired number. Valid entries are from [000] to [255]. Program data [000] to disable the feature. Keypads will remain lock ed out for the numbe r of minutes programmed for the Lockout Duration. Valid entries are from [000] to [255].

Section [013] First System Option Code

Option Description

[1] ON: zones require normally-closed loops. OFF: zones require 5.6K End-Of-Line resistors. [2] ON: zones require double End-Of-Line resistors. OFF: zones require single End-Of-Line resistors. [3] ON: keypads will display all trouble conditions while armed. OFF: keypads will only display fire trouble when armed.

This option must be OFF if LCD5500 v2.x (or older) keypads are used on the system.

[4] ON: only a trouble will be displayed. OFF: keypads will display a trouble and a zone violation if a tamper or fault is detected.

12

Section 4 – Programming Descriptions

[5] ON: auto-arming schedules (Program Sections [181]-[188]) will be available to the user in the [][6] menu.

OFF: auto-arming schedules will NOT be available to the user in the [][6] menu.

[6] ON: the Audible Exit Fault feature will be enabled. If a delay zone is not secured correctly and not force-armed, at the end of the exit delay,

the system will go into entry delay and turn ON the bell output. The bell will also sound if the delay zone is opened within 10 seconds of the exit delay timeout. OFF: the keypad will sound the entry delay through the keypad as normal.

[7] ON: the system will NOT log additional alarms for a zone that has reached the swinger shutdown threshold.

OFF: all zone alarms will be logged.

[8] ON: Temporal Three Fire Signal is used to annunciate fire alarms

(½ second ON, ½ second OFF, ½ second ON, ½ second OFF ½ second ON, 1 ½ seconds OFF).

OFF: the system will pulse the bell output

(½ second ON, ½ second OFF).

Section [014] Second System Option Code

Option Description

[1] ON: the system squawks the bell output once when a partition is armed, twice when disarmed. OFF: the bell output does not

activate. Refer to section [017] option 8.

[2] ON: the system squawks the bell output every 10 seconds during the auto-arm pre-alert. OFF: the bell output does not activate. [3] ON: the system will squawk the bell output once every second during Exit Delay, 3 squawks per second for the last 10 seconds.

OFF: the bell output will not activate.

[4] ON: the system will squawk the bell output once every second during Entry Delay, 3 squawks per second for the last 10 seconds.

OFF: the bell output will not activate.

[5] ON: the system squawks the bell output once every 10 seconds when a trouble condition is present.

OFF: the bell output does not activate.

[6] ON: the system will beep the keypads once every second, and 3 times a second during the last 10 seconds, during exit delay when

the system is armed with a user code or armed in the Away mode. OFF: the keypads will not beep.

[7] ON: the exit delay will be term inated (re duced to 5 seconds) when a Delay 1 zone is violated and restored after the system is armed.

OFF: the exit delay will count down as normal.

[8] ON: the bell output will not timeout if a fire alarm occurs. The user must turn OFF the bell by entering a valid user code.

OFF: the bell output will timeout normally.

Section [015] Third System Option Code

Option Description

[1] ON: the keypad [F] fire emergency key will be enabled. OFF: the keypad [F] fire emergency key will be disabled. [2] ON: the keypad [P] panic emergency will be audible (bell output). OFF: the keypad [P] emergency key will be silent. [3] ON: the Quick Exit feature will be enabled. OFF: the Quick Exit feature will be disabled. [4]

ON: the Quick Arming [

If this feature is disabled, a valid user code must be entered after the Stay or Away function buttons are pressed.

][0] feature will be enabled. OFF: Quick Arming [][0] feature will be disabled.

[5] [6] ON: the Master Code (user code 40) can only be changed in Installer Programming. OFF: the Master Code can be changed using

[7] ON: the system supervises the telephone line and displays a trouble if disconnected. OFF: the telephone line is not supervised.

ON: a valid user code must be entered after pressing [

the User Programming [

][5] command.

][1] to access the Bypass feature. OFF: a user code is not required.

13

PowerSeries - PC1616/PC1808/PC1832/PC1864

[8] ON: the system activates the bell output if a telephone line trouble is detected while the system is armed. OFF: the system activates

the keypad buzzer trouble tone.

Section [016] Fourth System Option Code

Option Description

[1] ON: the system supervises the AC input and displays a trouble if a failure is detected. OFF: AC Input is not supervised. [2] ON: the trouble light will flash when an AC trouble is detected. OFF: the trouble light turns on, does not flash. [3] ON: the keypad blanks (no indicator lights) if a key is not pressed for 30 seconds. OFF: the keypad does not blank. [4] ON: a valid user code must be entered to restore normal keypad operation after the blanking. OFF: pressing any key will return the

keypad to normal operation.

[5] ON: keypad backlighting enabled. OFF: keypad backlighting disabled. [6] ON: the system temporarily enables the Keypad Blanking feature if an AC failure is detected (to preserve the back up battery).

OFF: the system will operate as normal.

[7] ON: the keypad turns ON the Bypass light if zones are bypassed while the system is armed. OFF: the Bypass light turn s OFF when

the system is armed.

[8] ON: the system supervises keypad tampers. OFF: the system does not supervise keypad tampers.

Section [017] Fifth System Option Code

Option Description

[1] ON: the system does NOT associate wireless keys to user codes. OFF: the system will assign user code 17 to wireless key #01, user

code 18 to wireless key #02 etc. If the wireless key is used to arm or disarm, the system will report the Opening or Closing for the associated User Code.

[2] ON: the system logs an RF Jam trouble condition if the condition is present for 5 minutes. OFF: the system logs the trouble

condition after 30 seconds.

[3] ON: the keypads beep if an RF Jam trouble is detected. OFF: the trouble is not annunciated via the keypad buzzer. [4] ON: the Double Hit feature will be enabled. Two violations from the same zone within the Cross Zone Timer will be considered a

valid Police Code or Cross Zone event. The system will report the event and log it to the event buffer.

OFF: two alarms from the same zone is not a valid Police Code or Cross Zone event.

[5] ON: the system logs and communicates a Late-To-Close event when it auto-arms at the programmed time (not if auto arming was

caused by the No-Activity Arming feature). OFF: the system does not transmit or log a

[6] ON: enables the Daylight Savings aut omatic cl ock adju stment fe ature. OFF: the system does not automa tically a djust the clock for

Daylight Savings.

[7] For Future Use [8] ON: the system only squawks the bell output when the system is armed in the Away mode. OFF: the system squawks the siren

when the system is armed in any mode. (See Section [14]).

Late-To-Close event.

Section [018] Sixth System Option Code

Option Description

[1] ON: the system only tra nsmit s a Te st Tr ans mi ssio n reporting code if no other event was t ransm itted to the ce ntral station during the

programmed time. OFF the system always transmits a Test Transmission reporting code as programmed.

[2]-[4] For Future Use

14

Section 4 – Programming Descriptions

[5] ON: the keypad buzzer follows the bell output for all alarms. OFF: the system only activates the bell output for all alarms. [6] ON: When an alarm is detected on a zone (with the Cros s Zone attribute enable d), a timer is started. The alarm is not tran smitted and

the bell output is not activated unless a second cross zone enabled zone is violated before the Cross Zone timer times out. OFF: the system reports all alarms normally and logs and transmits a Police Code reporting code if a second zone alarm is detected during the armed period.

[7] ON: the system restarts the Exit Delay (one time) if a Delay zone is violated and restored during the exit delay time. OFF: exit

delay does not restart.

[8] ON: the system activates the trouble beeps when an AC trouble is d etected. OFF: the system does not annunciate AC troubles using

the keypad buzzer.

Section [019] Seventh System Option Code

Option Description

[1] For Future Use [2] ON: Trouble light latches on OFF: Trouble light turns off after restore. [3]

[4]-[5] For Future Use

[6]

[7] ON: All user access codes can enter the User Function s menu. OFF: Only the Master Code can enter the User Functions menu. [8] For Future Use

ON: When disarming, the keypad will display only the first alarm to occur during the last arming period OFF: When disarming,

the keypad will display all zones that were in alarm during the last arming period

ON: the green LED indicator on the keypads indicate the status of AC on the system OFF: the green LED indicator on the keypads indicate the partition ready status

Section [020] Keypad Zone Assignment

Enter the two-digit zone number to be assigned to each keypad assigned to a specific slot. Only one keypad can be assigned to a specific slot. See Keypad Assignment. Valid entries are from [00] to [64].

Section [021] Eighth System Option Code

Option Description

[1] ON: Access codes will not be accepted by the system during entry delay. OFF: An access code can be used to disarm the system

during entry delay

[2]-[5] For Future Use

[6]

[7]-[8] For Future Use

ON: Key-switches and wireless can only disarm the system during an entry delay. OFF: Key-switches and wireless keys can

disarm the system regardless if entry delay is active or not.

Section [022] Ninth System Option Code

Option Description

[1]

[2]-[3] For Future Use

ON: An access code is required for access to the [ [

][3] menu access.

][1], [][2], [][3] menus. OFF: No access code is req uired for [][1], [][2],

[4] ON: Only the Master code can be used to bypass a hold up zone. OFF: Any valid access code can bypass a hold up zone. [5] For Future Use

[6] Refer to the PC1616/PC1832/PC1864 Reference Manual for RF Delinquency details.

15

PowerSeries - PC1616/PC1808/PC1832/PC1864

[7] Future Use [8] ON: When the system is armed in Stay mode, during the Exit delay, the system will sound 1 beep every 3 second.

OFF: When the system is armed in Stay mode, the system will be silent during the Exit delay.

Section [023] Tenth System Option Code

Option Description

[1] ON: the keypad [F] emergency key will only beep three times to acknowledge the button has been pressed. The system will not

activate the bell output. OFF: the system will activate the bell output and beep the keypad. [2] Refer to the PC1616/PC1832/PC1864 Reference Manual for 200 Baud Open/Close Identifier details. [3] ON: the system will only transmit the Test Transmission reporting code if the system is armed at the time the system is programmed

to report the event. OFF: the system will always report the Test Transmission reporting code at the programmed time. [4] ON: the system changes the Test Transmission Reporting Cycle Time from Days to Hours. OFF: the Test Transmission Reporting

Cycle Time is in Days. [5] ON: the user cannot switch from Away Arm mode to Stay Arm mode using the function keys. OFF: the user can switch arming

modes.

[6] ON: the system disconne cts a listen in/two-way session if a new event occurs.

OFF: the system does NOT disconnect. New events are transmitted only after the session is terminated. [7] ON: the system does NOT activate the keypad buzzer for any trouble condition (excluding Fire Troubles). OFF: the system

annunciates troubles via the keypad buzzer (two beeps every 10 seconds) normally. [8] ON: Keyswitches will always arm in away mode. OFF: Keyswitches will arm in away mode if an entry/exit zone is violated during

exit delay.

Section [030] Fast Loop Response

This section is used to determine the Loop Response Time for the main panel zones.

ON: the loop response time will be 36 mS. OFF: the loop response time will be 400 mS.

Section [101] to [164] Zone Attributes

These sections are used to customize the operation of the zones. There are 9 toggle options in each Section:

Option Description

[1] ON: alarms are audible (bell output). OFF: alarms are silent. [2] ON: the bell output is steady (burglary). OFF: the alarm output pulses (fire). [3] ON: a zone violation or restoral will activate Chime. OFF: Chime is not activated. [4]

[5] ON: the partition can be armed even if the zone is violated (the zone will not affect the Ready status). OFF: the zone must be

ON: the user can manually bypass the zone using the [

secure before arming.

][1] command. OFF: the zone cannot be manually bypassed.

[6] ON: the system shuts down alarm reporting after the programmed number of alarms have occurred. OFF: the panel will always

report the event if an alarm occurs.

[7] ON: the system delays reporting the event for the time programmed for the Transmission Delay time. OFF: the panel

immediately transmits the reporting event when an alarm is detected.

[8] ON: the zone is a wireless or addressable device. OFF: the zone is a hardwire zone (main panel, zone expander or keypad zone). [9] ON: the zone has the Cross Zone feature enabled. OFF: the zone functions normally.

16

Section 4 – Programming Descriptions

[10]-[13] For Future Use

[14] ON: the zone requires a normally-closed loop. OFF: the zone will follow the EOL configuration in Section [013] [15] ON: the zon e requires a single End-of-Line resistor. OFF: the zone will follow the EOL configuration in Section [013] [16] ON: the zone requires a double End-of-Line resistors. OFF: the zone will follow the EOL configuration in Section [013]

Options 14, 15, 16 apply to first 8 zones only. If more than one of these options are enabled then lowest numbered option is enabled. E.g., If Option 14 and option 15 are enabled then the zones are configured as normally closed loops.

Keypad zones and zone expanders will always follow Section [013].

When Zone Types (Section [001] to [004]) are programmed, the system will change the Zone Attributes to those found in the chart included in the Programming Worksheets. The Zone Attributes will default if a new Zone Type is programmed for a specific zone. After programming the Zone Types, enter Section [101] to [164] and ensure that all options are programmed correctly.

Ready light ON: Program attributes [1-8] (press [1]-[8] to turn option ON or OFF) Ready light and Armed light ON: Program attributes [9-16] (press [1]-[8] to turn option ON or OFF)

Press [9] to switch between attributes [1-8] and attribute [9-16].

Section [165] Maximum Dialing Attempts

Program the Maximum Dialing Attempts before the panel will generate a Failure to Communicate (FTC) trouble condition. Valid entries are [001] to [005]. For UL Listed installations, 5 attempts is required.

Section [166] Post Dial Wait for Handshake

Program the maximum time the panel will wait, after dialing, for a valid handshake from the central station. Valid entries are [001] to [255] seconds.

Section [167] T-Link Communications Wait for Acknowledgement

Program the maximum time the panel will wait, after sending a data packet, for an acknowledgement from the central station. Valid entries are [001] to [255] seconds.

Section [168] Daylight Savings Time (Move Clock Ahead)

These sections are used to program the Date, Time and Increment that the clock will move ahead for Daylight Savings Time each year. Programming can be accomplished by programming the Month, Day, Hour and Increment or Month, Week, Day of Week, Hour and Increment:

Month Data [001] to [012] represents January to December. Week Data [000] indicates that the day of the month will be programmed in the Day section below . Data [001] to [005] represents

weeks 1 to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the month is 4 or 5.

Day Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was

programmed in the Week Section above, then Data [000] to [006] represents Sunday to Saturday

Hour Data [000] to [022] represents the hour that Daylight Saving Time will take effect. Increment Data [001] to [002] represents the number of hours to advance the clock for Daylight Savings Time.

Do not program the Hour outside of the valid range or the time will not change. Do not program the value of the Increment to be

greater then the number of hours remaining in the current day.

Section [169] Standard Time (Set Clock Back)

These sections are used to program the Date, Time and Increment that the clock will move back for Standard Time each year. Programming can be accomplished by programming the Month, Day, Hour and Increment or Month, Week, Day of Week, Hour and Increment:

Month Data [001] to [012] represents January to December. Week Data [000] indicates that the day of the month will be programmed in the Day section below . Data [001] to [005]

weeks 1 to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the month is 4 or 5.

Day Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was

programmed in the Week Section above, then Data [000] to [006] represents Sunday to Saturday

Hour Data [000] or [023] represents the hour that Standard Time will take effect. Increment Data [001] or [002] represents the number of hours to roll back the clock for Daylight Savings Time.

represents

17

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [170] PGM Output Timer

Program the time, in seconds, PGM outputs programmed to follow the PGM Output Timer will activate for. Valid entries are [001] to [255].

Section [171] Tamper PGM Output Timer

Program the time, in minutes, that a tamper condition will latch the Tamper PGM output. Valid entries are [000] to [255].

Section [175] Auto-arm Postpone Timer

Program the time, in minutes, that the system will postpone automatic arming. After the programmed time, the system will attempt to auto arm again. If data [000] is programmed, the system will instead abort the auto arm sequence. Valid entries are [001] to [255].

Section [176] Cross Zone/Police Code Timer

Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel will use to determine if a Cross Zone or Police Code event has occurred. If data [000] is programmed when using the Police Code feature, the panel will generate a Police Code event if any two zones go into alarm during any armed-to-armed period. V a lid entries are [001] to [255].

Section [181] to [188] Auto-arm Schedules

Program the time to auto arm (Section [181] for Partition 1, Section [182] for Partition 2 etc.) for each day of the week. Each Section has seven, 4-digit entries, two digits for the hour, two digits for the minute, for S unday through Saturday. Program using the military format (for example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto arming.

Section [190] No Activity Arming Pre-alert Duration

Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will provide a steady tone warning the user that the system will arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].

Section [191] to [198] No Activity Arm Timer

Program the time, in minutes, for the No Activity Arm Timer (Section [191] for Partit ion 1, Section [192] for Partition 2 etc.). If Delay Zones are restored and no zone activity is detected for the time programmed, the syst em will start the auto arm sequence. Valid entries are [000] to

[255].

Section [199] Auto-Arming Pre-alert Timer

Program the time, in minutes, for the Auto-Arming Pre-Alert Time. This timer is used for all programmed auto-arming features (is not used for No Activity Arming). The keypads will provide a steady tone warning the user that the system will arm. The user can enter a valid access code to abort the arming sequence. Valid entries are [000] to [255].

Section [201] Partition Selection Mask

Turn the corresponding option ON to enable partitions [1] to [8]. ON (bit 1 cannot be turned OFF).

Section [202] to [265] Partition Zone Assignments

These Sections are used to assign zones to specific partitions (Section [202] to [209] for Partition 1, Sections [210] to [217] for Partition 2 etc.). Turn ON the option corresponding to the partition and zone to enable the zone on the specified partition. Turn the option OFF to disable the zone on the specified partition. Zones assigned to more than one partition are called ‘common zones’ and will only be armed if all the partitions the zone is assigned to are armed. Default = Zones 1-8 enabled on Partition 1.

Section [301] to [303] Telephone Numbers

Program the phone numbers as required. Phone Number 3 is dedicated as a back-up to Phone Number 1. HEX digits can be included for special applications:

HEX [A] Not used HEX [B] Simulates a [ HEX [C] Simulates a [#] key press HEX [D] Additional dial tone search HEX [E] 2-second pause HEX [F] End of phone number marker

] key press

Section [304] Call Waiting Cancel String

Program the digits required to disable call waiting. If enabled, the system will dial the programmed string on the first dialing attempt. Program unused digits with data [F].

Section [310] System Account Number

Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required, program the last two digits as data [FF]. If using the SIA format, this account number will be used for all reporting events. If using a

18

Section 4 – Programming Descriptions

different format, this account number will be used for all events that are not partition specific (for example, low battery, AC trouble etc.). For partition specific events the system will use the programmed Partition Account Number. For all formats other than SIA, program a HEX

[A] for any digit [0] in the account number being used.

Section [311] to [318] Partition Account Numbers

Program the Partition Account Number for each active partition (Section [311] for partition 1, Section [312] for partition 2 etc.). When using the Automatic SIA format, these account numbers are not used. The system will use the System Account Number for all reporting events. For all formats other than SIA, program a HEX [A] for any digit [0] in the account number being used.

Section [320] to [349] Reporting Codes

Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting event when transmitting to the central station. For all format s excluding Automatic SIA and Automatic Contact ID, the panel will not attempt to report an event if data [00] or data [FF] is programmed for the reporting code.

Section [350] Communicator Format

Program the 2-digit number for the desired Communicator Format for the First Phone Number and Second Phone Number. When dialing the Third Phone Number, the system will use the Communicator Format programmed for Phone Number 1. Valid entries are [01] to [13]. Refer to the Programming Worksheet for a list of the available Communicator Formats. Refer to the PC1616/PC1832/PC1864 Reference Manual for Communicator Format details.

Section [351] to [376] Communicator Call Direction Options

Reporting events are categorized into 5 groups; Alarm/Restore, Opening/Closing, Tamper Alarm/Restore, System Maintenance and Test Transmissions. Program which Phone Number the control panel will use to transmit reporting events by turning the option ON in th e corre ct Section. Phone Number 1 and/or Phone Number 2 can be used.

Section [377] Communicator Variables

Program a 3-digit number for each program entry:

Swinger Shutdown (Alarms): Maximum number of alarm/restoral transmissions per zone. Valid entries: [001] to [014]. Program data [000] to disable shutdown.

Swinger Shutdown (Tamper): Maximum number of tamper alarm/restoral transmissions per zone. Valid entries: [000] to [014]. Program data [000] to disable shutdown.

Swinger Shutdown (Trouble): Maximum number of trouble alarm/restoral transmissions per trouble condition. Valid entries: [000] to [014]. Program data [000] to disable shutdown.

Communicator (Transmission) Delay: Time, in seconds, panel will delay reporting an alarm event. Valid entries: [000] to [255]. AC Failure Communication Delay: Time, in minutes, panel will delay reporting an AC trouble event. Valid entries: [000] to [255]. TLM Trouble Delay: Time, in 3 second checks, before the system will consider the phone line disconnected. Valid entries: [002] to [255]

(e.g., 3 x10 seconds = 30 seconds).

TLM Restoral follows the same delay.

Test Transmission Cycle (Land Line): Number of days between test transmission reporting events. Valid entries: [001] to [255]. For Future Use Wireless Zone Low Battery Delay: Number of days the system will delay reporting a wireless low battery to the central station.

Valid entries: [000] to [255]. Program data [000] for no delay. Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel will delay before transmitting

the event to the central station. Valid entries: [001] to [255]. Communication Cancel Window: Time, in seconds, after an alarm has occurred that the system will report a Communication Cancel reporting event

if the system is disarmed. They keypad will beep rapidly to indicate the Communication Cancel reporting event has been communicated successfully. Valid entries: [001] to [255].

Section [378] Test Transmission Time

Program the time the system will report a Test Transmission reporting event. Program 4 digits – [HH][MM] using military standard. For a test transmission at 11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59].

19

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [379] Periodic DLS Time of Day

Programs the time the system will auto-call DLS. Program 4 digits – [HH][MM] using military standard. For a DLS auto-call at 11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59]. Programming [99][99] will select a random time, [FF][FF] will disable it. Please refer to the PC 1616/1832/1864 Reference Manual for a complete description of Periodic DLS.

Section [380] First Communicator Option Code

Option Description

[1] ON: the system communicator is enabled. OFF: the communicator is disabled. [2] ON: the system transmits alarm restorals if the zone is restored and the bell has timed out. OFF: the system transmits alarm restorals

immediately when the zone is restored.

[3] ON: the panel uses rotary (pulse) dialing. OFF: the panel uses touchtone (DTMF) dialing [4] ON: the panel will switch from touchtone dialing to rotary dialing after the 4th failed attempt to communicate.

OFF: the panel will use DTMF dialing for all dialing attempts.

[5] ON: the system uses the Third Phone Number to back up the First Phone Number. OFF: the Third Phone Number is disabled. [6] ON: the system alternates between the First Phone Number and Third Phone Number when attempting to report an event.

OFF: the panel will dial the First Phone Number for the programmed number of attempts, then switch to the Third Phone Number.

[7] For future Use [8] ON: the Delinquency feature follows zone activity. OFF: the Delinquency feature follows arming.

Section [381] Second Communicator Option Code

Option Description

[1] ON: the keypad beeps 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the keypad does not beep. [2] ON: the bell output squawks 8 times after successfully transmitting the Opening After Alarm reporting event. OFF: the bell output does

not activate.

[3] ON: the system uses programmed reporting codes when transmitting using the SIA format.

OFF: the system automatically generates all reporting codes transmitted.

[4] ON: the system beeps the keypad 8 times after successfully transmitting a Closing reporting event. OFF: the keypad does not beep. [5] ON: the system requests a Listen in/Two-way session the next time it calls the 1st/3rd Phone Number when the PC59xx transmits a

request. OFF: the system ignores the request from the PC59xx.

This Option is used with PC59xx series modules.

[6] ON: the system requests a Listen in/Two-way session the next time it calls the 2nd Phone Number when the PC59xx transmits a request.

OFF: the system will ignore the request from the PC59xx.

This Option is used with PC59xx series modules.

[7] ON: the system uses Contact ID format programmed reporting codes when transmitting reporting codes.

OFF: the system automatically generates all reporting codes transmitted.

[8] ON: the system will follow ULC Communication Priority. OFF: the system will follow standard com munications priority.

Section [382] Third Communicator Option Code

Option Description

[1] ON: the system will use the digit [5] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.

OFF: the system will use the digit [4] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.

[2] ON: the system will transmit all alarms during Walk Test. OFF: the system will not report alarm events during Walk Test.

20

Section 4 – Programming Descriptions

[3] ON: the keypad will display the message ‘Communications Cancelled’ (programmable LCD) or ‘CC’ (fixed-message LCD) upon

successful transmission of the Communication Cancelled reporting event. OFF: the keypad will not display these messages.

[4] ON: the system dials the Call Waiting Cancel String on the first attempt to dial the central station. OFF: the system does not dial the Call

Waiting Cancel String.

[5] ON: enables support for the T-Link module. OFF: disables T-Link. [6] ON: the AC Failure Transmission Delay Timer will use hours. OFF: the delay will be in minutes. [7] ON: Sets the number of Dialing attempts to 1 when using Residential Dial Format. OFF: Residential Dial follows Dialing Attempt

Counter.

[8] For Future Use

Section [383] Fourth Communicator Option Code

Option Description

[1] ON: Events programmed to communicate to phone #1 will use the Partition Account Number in section [311]. Events Programmed to

communicate to phone #2 will use the Partition Account Number in section [312]. OFF: Each events will use its respective partition account code.

[2-8] For Future Use

Section [389] T-Link Fault Check Timer

Program the period of time (in seconds) in between checks to see if the T-Link module is present. Valid entries are [001]-[255].

Section [401] First Downloading Option Code

Option Description

[1] ON: the system answers incoming calls for downloading (either Programmed Number of Rings or Double Call). OFF: the system does not

answer incoming calls using the double call routine for downloading.

These settings do not affect the 6 hour DLS downloading window on power up.

[2] ON: the user can enable downloading for the DLS Window using the [][6] command. OFF: the user cannot enable downloading. [3] ON: the system will hang up after a successful DLS connection and call the computer back using the DLS Phone Number (Section [402]).

OFF: the system stays connected to the computer. [4] ON: the user can initiate a downloading session using the [][6] command. OFF: the user cannot initiate a downloading session. [5] ON: the system attempts to call the downloading computer after transmitting a Event Buffer 75% Full event to the central station. OFF: the

system does NOT call the downloading computer after transmitting this event.

[6] ON: Panel communicates with DLS at 300 Baud. OFF: Panel communicates with DLS at 110 Baud.

[7]-[8] For Future Use

Section [402] Downloading Computer Phone Number

The Downloading Computer Telephone Number is used for Call Back, User Initiated DLS and the Auto Event Buffer Upload functions. Program the phone number as required. HEX digits can be included for special applications:

HEX [A] Not used HEX [B] Simulates a [ HEX [C] Simulates a [#] key press HEX [D] Additional dial tone search HEX [E] 2-second pause HEX [F] End of phone number marker

] key press

Section [403] Downloading Access Code

Program the 6-digit Downloading Access Code. Upon connection, the system will only connect to the downloading computer if the Downloading Access Code programmed matches the Downloading Access Code programmed in the computer file.

21

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [404] Panel Identification Code

Program the 6-digit Panel Identification Code. This code is used by the downloading computer to verify the correct account is calling back (Call Back feature) or to identify which customer account file should be used (User Initiated DLS and Auto Event Buffer Upload features).

Section [405] Double-Call Timer

Program the maximum time, in seconds, between calls when connecting to panel using the double call feature. Valid entries are [000] to [255].

Section [406] Number of Rings to Answer On

Program the number of consecutive rings that panel must detect to answer for downloading. Valid entries are [000] to [010].

Section [499] PC-Link Communications

Enter the following command to initiate downloading via PC-Link – Section [499] [Installer Code] [499] . Plugging in the PC-Link connector will automatically initiate the connection if DLS is initiated before connecting the PC-Link Header. The session will NOT be automatically initiated if the system is in installer mode.

Section [501] to [514] Programmable Output Attributes

These Sections are used to customize the operation of the PGM outputs (Section [501] for PGM 1, Section [502] for PGM 2 etc.). The avail- able options depend on which PGM output type is programmed.

When the PGM Output Options (Section [009] to [011]) are programmed, the system will change the PGM Attributes to the default settings. The PGM Attributes will default if a new PGM output option is programmed.

PGM Output Option [01], [03] to [08], [11] to [22], [25],[26], [28], [30], [33], [34]

Option Description

[3] ON: the PGM output will operate normally (switch to ground when activated). OFF: the PGM output will be normally ground and switch

to open collector (open circuit) when activated.

PGM Output Option [19] to [22]

Option Description

[4] ON: the PGM output will activate for the duration of the PGM Output Timer when the [][7][x] command is pe rformed.

OFF: the PGM output will latch until the [][7][x] command is performed again.

[5] ON: a valid user code must be entered after the [][7][x] command. OFF: user code is not required.

PGM Output Option [09]

Option Description

[1] ON: PGM output activates if a Service Required trouble condition is present. [2] ON: PGM output activates if an AC trouble condition is present. [3] ON: PGM output activates if a Telephone Line trouble condition is present. [4] ON: PGM output activates if a Failure to Communicate trouble condition is present. [5] ON: PGM output activates if a Zone Fault condition is present. [6] ON: PGM output activates if a Zone Tamper condition is present. [7] ON: PGM output will activates if a Wireless Low Battery trouble condition is present. [8] ON: PGM output will activates if a Loss of Clock trouble condition is present.

PGM Output Option [10]

Option Description

[1] ON: PGM output activates if a Burglary Alarm occurs. [2] ON: PGM output activates if a Fire Alarm occurs.

22

Section 4 – Programming Descriptions

[3] ON: PGM output activates if a Panic Alarm occurs. [4] ON: PGM output activates if a Medical Alarm occurs. [5] ON: PGM output activates if a Supervisory Alarm occurs. [6] ON: PGM output activates if a Priority Alarm occurs. [7] ON: PGM output will activates if a 24-Hour Hold-Up Alarm occurs. [8] ON: the PGM output activates for the time programmed for the PGM Output Timer. OFF: the PGM output will latch until a valid user co de

is entered.

PGM Output Option [31]

Option Description

[1] ON: PGM output activates if a Fire Alarm occurs. [2] ON: PGM output activates if a Panic Alarm occurs. [3] ON: PGM output activates if a Burglary Alarm occurs. [4] ON: PGM output activates if an Opening/Closing occurs. [5] ON: PGM output activates if a a zone is automatically bypassed. [6] ON: PGM output activates if a Medical Alarm occurs. [7] ON: PGM output will activates if a confirmed alarms occurs and Police Code occurs. [8] ON: the PGM output is active when the selected condition is true. OFF: the PGM output will latch until a valid user code is entered

PGM Output Option [32]

Option Description

[1]-[7] For Future Use

[8] ON: the PGM will activate for the duration programmed in PGM Output Timer. OFF: the PGM will activate when an Opening After Alarm

occurs and will deactivate when a valid access code is entered.

PGM Output Option [29] and [35]-[41]

Option Description

[1]-[2] For Future Use

[3] ON: the PGM will switch to ground when the event occurs. OFF: the PGM will switch to open when the event occurs.

[4]-[7] For Future Use

[8] ON: AND logic is selected, all zones that are enabled must be violated before the PGM will activate. OFF: OR Logic is selected, only one

violated zone is required to activate the PGM. All zones must be restored to turn it OFF.

Zones are assigned to this PGM in the PGM Partition Assignment Section [551]-[564]

Section [551] to [564] PGM Partition Assignment

These sections are used to customiz e the operation of the PGM outputs (Section [551] for PGM 1, Section [552] fo r PGM 2 etc.). T urn on the correct option in the correct section to assi gn the PGM output to a specified partition. PGM outputs can be assigned to more than one partition. For PGM outputs that are considered ‘system’ outputs (e.g.,Trouble output), programming in these sections will not affect the operation of the PGM output.For Zone Follower PGM types 29, 35-41 these sections are used to assign specific zones to the PGM.

Any one Command Output PGM type cannot be assigned to more then one partition.

23

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [601] to [608] Additional Reporting Codes

Program the reporting code for all events to be transmitted. For description of when each reporting event will be transmitted, refer to Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting event when transmitting to the central station. For all formats excluding Autom atic SIA and Automatic Contact ID, the panel wil l not attempt to report an event if data [00] or data [FF] is programmed for the reporting code.

Section [681] to [688] Auto-Disarm Schedules

Program the time to auto-disarm (Section [681] for Partition 1, Section [682] for Partition 2 etc.) for each day of the week. Each Section has seven, 4-digit entries, two digits for the hour, two digits for the minute, for S unday through Saturday. Program using the military format (for example, to auto arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto disarming

Section [691] to [698] Auto-Disarm Holiday Schedule

Program the dates to be used for Auto-Disarm holiday schedule (Section [691] for Partition 1, Section [692] for Partition 2 etc.) Each Section has fourteen, 6-digit entries, two digits for the month, two digits for the day and two digits for the year.Th e panel will not disarm on the programmed dates. The format of entering the date is MMDDYY. Program [99][99][99] to disable Auto-Disarm holiday schedule.

Section [700] Automatic Clock Adjust

Program the number of seconds for the last minute of the day. This can be used to make minor corrections to the clock if the AC frequency is not reliable. Valid entries are [01] to [99].

Section [701] First International Option Code

Option Description

[1] ON: configures the system for 50Hz AC. OFF: configures the system for 60Hz AC. [2] ON: the system uses the internal crystal for the internal panel clock. OFF: the system uses the AC frequency for the internal panel clock. [3] ON: the system will inhibit arming if a Low Battery or AC trouble condition is present. OFF: arming will not be inhibited. [4] ON: all Tamper troubles will latch and arming will be inhibited. Enter Installer Programming to clear the trouble condition and return to

normal operation. OFF: tamper troubles will not latch and will not inhibit arming. [5] ON: all access codes are 6 digits long. OFF: all access codes are 4 digits long. [6] ON: the system will hang up if a busy tone is detected. This attempt is not counted towards the Maximum Dialing Attempts programmed.

OFF: the panel will not detect busy tones. [7] ON: the system will charge the battery at approximately 700mA. OFF: the system will charge the battery at 400mA. [8] ON: the system will abort a DLS session, Escort access, Listen In/Two-way session if a new central station communication event occurs.

OFF: non-critical events (Test transmission, Periodic Test and System Test) will not abort the session. Events will be communicated after

the session is complete.

Section [702] Second International Option Code

Option Description

[1] ON: the communicator uses 33/67 make/break ratio when pulse dialing. OFF: the system uses 40/60 make/break ratio. [2] ON: the system dials regardless of the presence of dial tone after the first attempt. OFF: the system dials only if dial tone is detected. [3] ON: changes the Test Transmission Cycle Time to minutes. OFF: sends a Test Transmission after the programmed number of days. [4] ON: the system accepts 1600Hz handshake pulse formats. OFF: the system accepts 1400Hz or 2300Hz handshakes. [5] ON: the system generates a tone for 500mS every 2 seconds indicating digital equipment is making the call vs. a voice call.

OFF: the system does not generate a tone. [6] ON: the tone generated (2100Hz.) indicates that digital equipment is making the call. OFF: the tone is 1300Hz. [7] ON: the DLS down loading window is 1 hour. OFF: the DLS downloading window is 6 hours. [8] ON: the system activates the bell output if a Failure to Communicate trouble occurs while the system is armed.

OFF: the system does NOT activate the bell output if a Failure to Communicate trouble occurs while the system is armed.

24

Section 4 – Programming Descriptions

Section [703] Delay Between Dialing Attempts

Program the time the panel will wait between dialing attempts to transmit a reporting event to the ce ntra l station. Valid entries are [001] to [255].

Section [800]-[851] Module Programming

The following program sections are used to program different modules that can be connected to the control panel. Refer to the respective Installation Manual for installation and programming information

Section [801]: PC5400 Printer Module Programming Section [802]: PC59xx VOX Module Programming Section [803]: Al ternate Communicator Programming Section [804]: Wireless Programming Section [805]: PC5100 Addressable Programming Section [851]: T-Link Programming

Special Installer Instructions

Section [899] Template Programming

Selecting [][8] [Installer Code] [899] displays the current 5-digit template programming code. Refer to Section 3.1 Template Programming on page 8 for programming details. Refer to Appendix C - T emplate Programming for a detailed description of available templa tes and

corresponding 5 digit codes.

This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.

Section [900]: Panel Version Displayed

Only available with LCD5500 or PK5500 keypads. The system will display the version of the control panel (for example, [0410] indicates panel version 4.10).

Section [901]: Installer Walk Test

The system will turn Installer Walk Test ON. The Ready, Armed and Trouble LED’s will flash rapidly while the test is active. Every time a zone is violated the system will activate the bell output for two seconds and log the event to the event buffer . To turn Installer Wa lk Test OFF enter Section [901] again. The system automatically terminates the test of there is no zone activity for 15 minutes.

Section [902]: Module Supervision Reset

All modules are automatically detected within one minute after being connected to the Keybus. Enter Section [902] to clear detected modules if a module is removed, if PC5108 jumpers are changed, or if a keypads slot assignments are programmed. The system will rescan the Keybus to determine which modules are connected.

Section [903]: View Module Supervision

The keypad will display the modules detected by the system by turning on the associated zone light (LED keypads), flashing the numbers (fixed-message LCD keypads) or displaying the modules detected in plain language (programmable LC D keypads). Refer to the chart below:

Indicator Light

(Zone)

[01] to [08] [09] to [14]

[15] [16] [17] [18] [19] [20] [21] [22] [24]

[26] to [29]

Keypad in Slot #1 to #8 PC5108 Zone Expander #1 to #6 PC5100 Module PC5108 Zone Expander #7 PC5132 Module or RFK keypad with integrated wireless receiver PC5208 PC5204 Module PC5400 Module PC59xx Module Alternate Communicator Escort5580 or Escort5580TC PC5200 #1 to #4

Module

25

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section [904]: Wireless Placement Test

Enter Section [904] followed by the 2-digit number of the wireless zone to test. When a wireless signal is received from th e s elected trans- mitter, the system will indica te th e loc ation as Good or Bad as follows:

Good: One bell squawk, 1 keypad beep, keypad zone light [1] ON Bad: Three bell squawks, 3 keypad beeps, keypad zone light [3] ON

Press [#] to exit when testing is complete. Enter the 2-digit zone number for the next wireless device to test or press [#] to return to standard programming.

Section [990]: Installer Lockout Enable

Enter Section [990][Installer Code][990] to enable the Installer Lockout feature. A hardware default cannot be performed when the Installer Lockout feature is ON. In addition, the system will chatter the line seizur e relay 10 times if the panel is powered up to indicate the feature is ON.

Section [991]: Installer Lockout Disable

Enter Section [991][Installer Code][991] to turn the Installer Lockout feature OFF.

Section [993] to [999]: Factory Default Module/Panel

The following Sections can be used to factory default a module or the main control panel. Enter the appropriate Section, followed by the Installer Code, followed by the Section number (E.g., [993][Installer Code][993])

Section [993]: Factory Default Alternate Communicator Section [995]: Factory Default Escort5580 Module Section [996]: Factory Default Wireless Receiver Section [997]: Factory Default PC5400 Module Section [998]: Factory Default PC59xx Module Section [999]: Factory Default Main Control Panel

Hardware Reset (Default) Main Control Panel

Perform the following to default the main control panel:

1. Power down the system completely.

2. Conn ect a short between Zon e 1 and PGM1 on the control panel (remove all other wires form these terminals).

3. Power up the control panel (AC power only) for 10 full seconds.

4. Power down the control panel, remove short between Zone 1 and PGM1.

5. Power up the control panel.

26

Section 5: Programming Work Sheets

Programming Option Page

[000] Keypad Enrollment .....................................................................28

[001]-[004] Zone Definitions................................................................28

[005] System Times.............................................................................29

[006] Installer’s Code...........................................................................30

[007] Master Code...............................................................................30

[008] Maintenance Code .....................................................................30

[009] PGM 1&2 Output Programming (Main Panel) ............................30

[010] PGM 3-10 Output Programming (Main Panel/PC5208) .............30

[011] PGM 11-14 Output Programming (PC5204) .............................30

[012] Keypad Lockout Options ............................................................30

[013] 1st System Options ....................................................................31

[014] 2nd System Options ...................................................................31

[015] 3rd System Options....................................................................31

[016] 4th System Options ....................................................................31

[017] 5th System Options ....................................................................32

[018] 6th System Options ....................................................................32

[019] 7th System Options ....................................................................32

[020] Keypad Zone Assignments ........................................................32

[021] 8th System Options ....................................................................33

[022] 9th System Options ....................................................................33

[023] 10th System Options ..................................................................33

[030] Zone Loop Response (Zones 1-8) .............................................33

[101] - [164] Zone Attributes ...............................................................34

[165] Maximum Dialing Attempts to Each Telephone Number ............36

[166] Post Dial Wait for Handshake (All Formats) ..............................36

[167] T-LINK Interface Communications Wait for Acknowledge ..........37

[168] Set Clock Forward (Daylight Saving Time).................................37

[169] Set Clock Back (Standard Time) ................................................37

[170] PGM Output Timer .....................................................................37

[175] Auto-arm Postpone Timer ..........................................................37

[176] Cross Zone/Police Code Timer .................................................37

[181]-[188] Automatic Arming Schedule .............................................37

[190] No Activity Arming Pre-Alert Time..............................................37

[191]-[198] No Activity Arming Timers ................................................38

[199] Auto-arming Pre-Alert Timer .....................................................38

[201] Partition Selection Mask.............................................................38

[301] 1st Telephone Number (32 Digits) ..............................................39

[302] 2nd Telephone Number (32 Digits).............................................39

[303] 3rd Telephone Number (32 Digits) .............................................39

[304] Call Waiting Cancel String (6 Digits) ..........................................39

[310] System Account Code................................................................39

[311]-[318] Partition 1-8 Account Numbers.........................................39

[320]-[323] Alarm Reporting Codes, Zones 01-64 ..............................39

[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64................40

[328] Miscellaneous Alarm Reporting Codes ......................................40

[329] Priority Alarm and Restoral .......................................................40

[330]-[333] Tamper Reporting Codes, Zones 01-64............................40

[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64 .............41

[338] Miscellaneous Tamper Reporting Codes ...................................41

[339]-[340] Closing (Arming) Reporting Codes,

Access Codes 1-32.....................................................................41

[341] Miscellaneous Closing (Arming) Reporting Codes.....................41

[342]-[343] Opening (Disarming) Reporting Codes,

Access Codes 1-32.....................................................................41

[344] Miscellaneous Opening (Disarming) Reporting Codes ..............42

[345] Maintenance Alarm Reporting Codes ........................................42

[346] Maintenance Restoral Reporting Codes ..................................42

Programming Option Page

[347] Miscellaneous Maintenance Reporting Codes .......................... 42

[348] Test Transmission Reporting Codes ......................................... 42

[350] Communicator Format Options ................................................. 43

[351]-[358] Alarm/Restore Communicator Call Directions..................43

[359]-[366] Tamper/Restore Communicator Call Directions ............... 43

[367]-[374] Opening/Closing Communicator Call Directions ..............43

[375] System Maintenance Communicator Call Directions ................ 44

[376] System Test Transmissions Communicator Call Directions ....... 44

[377] Communication Variables .......................................................... 44

[378] Test Transmission Time of Day ................................................. 44

[379] Periodic DLS Time of Day.......................................................... 44

[380] 1st Communicator Options ........................................................ 44

[381] 2nd Communicator Options .......................................................45

[382] 3rd Communicator Options ........................................................ 45

[383] 4th Communicator Options ........................................................45

[401] DLS Downloading Option Codes ...............................................45

[402] DLS Downloading Telephone Number (32 Digits) ..................... 46

[403]-[404] DLS Downloading Access Code / Panel ID Code ........... 46

[405] Answering Machine Double Call Timer......................................46

[406] Number of Rings to Answer On .................................................46

[499] Initiate PC-Link Downloading.....................................................46

[501]-[502] PGM 1&2 Output Attributes (Main Panel)......................... 47

[503]-[504] PGM 3&4 Output Attributes (Main Panel / PC5208)......... 47

[505]-[510] PGM 5-10 Output Attributes (5208).................................. 47

[511]-[515] PGM 11-14 Output Attributes (5204)................................ 47

[551]-[552] PGM 1&2 Output Partition Assignment (Main Panel)....... 48

[553]-[554] PGM 3&4 Output Partition Assignment

(Main Panel/PC5208) .......................................................................... 48

[555]-[560] PGM 5-10 Output Partition Assignment (5208)................ 48

[561]-[564] PGM 11-14 Output Partition Assignment (5204)..............48

[601]-[604] Closing (Arming) Reporting Codes .................................. 48

[605]-[608] Opening (Disarming) Reporting Codes............................ 49

[681]-[688] Automatic Disarming Schedule ........................................49

[691]-[698] Auto-Disarm Holiday Schedule ........................................ 49

[700] Automatic Clock Adjust ............................................................. 50

[701] 1st International Options ............................................................ 50

[702] 2nd International Options...........................................................50

[703] Delay between Dialing Attempts ................................................ 50

[801] PC5400 Printer Module Programming ....................................... 51

[802] PC59xx VOX Programming........................................................ 51

[804] PC5132 Wireless Expansion Programming...............................51

[805] PC5100 Programming ............................................................... 51

[851] T-LINK Programming.................................................................. 51

[899] Template Programming .............................................................. 51

[900] Panel Version Displayed ............................................................ 51

[901] Installer Walk Test Mode Enable/Disable .................................. 51

[902] Module Supervision Reset ....................................................... 51

[903] Module Supervision Field ........................................................ 51

[904] Wireless Module Placement Test ............................................. 51

[990] Installer Lockout Enable............................................................. 51

[991]

Installer Lockout Disable............................................................51

[993] Restore Alternate Communicator to Default Programming........ 51

[995] Restore Escort5580 to Default Programming ............................51

[996] Restore PC5132 to Default Programming.................................. 51

[997] Restore PC5400 to Default Programming.................................. 51

[998] Restore PC59xx to Default Programming..................................51

[999] Restore Control Panel to Default Programming......................... 51

5.1 Index to Programming Work Sheets

Section 5: Programming Work Sheets

27

PowerSeries - PC1616/PC1808/PC1832/PC1864

5.2 Programming Worksheets

Shaded programming sections indicate minimum programming requirements

\Keypad Partition /Slot and Function Key Programming

[000] Keypad Enrollment

This must be done at each keypad requiring programming.

[0] Slot address [Valid entries are 0-8 for the partition, 1-8 for the slot. (e.g., to enroll a keypad in partition 3 and slot 1, enter (31)] [1] Function Key 1 Assignment (Valid entries are 00-32) [2] Function Key 2 Assignment (Valid entries are 00-32) [3] Function Key 3 Assignment (Valid entries are 00-32) [4] Function Key 4 Assignment (Valid entries are 00-32) [5] Function Key 5 Assignment (Valid entries are 00-32)

Function Key Options:

00 Not used 11 [*][5] Access Code Programming 22 Global Disarming 01 Select Partition 1 12 [*][6] User Functions 23 Bypass Recall 02 Select Partition 2 13 Command Output #1 [*][7][1] 24 Recall Bypass Group 03 Stay Arm 14 Command Output #2 [*][7][2]/Sensor Reset 25 For Future Use 04 Away Arm 15 Global Stay Arming 26 Time and Date 05 [*][9] No-Entry Arm 16 [*][0] Quick Exit 27 Select Partition 3 06 [*][4] Chime On / Off 17 [*][1] Reactivate Stay/Away Zones 28 Select Partition 4 07 [*][6][——][4] System Test 18 Global Away Arming 29 Select Partition 5 08 [*][1] Bypass Mode 19 Command Output 3 [*][7][3] 30 Select Partition 6 09 [*][2] Trouble Display 20 For Future Use 31 Select Partition 7 10 [*][3] Alarm Memory 21 Command Output 4 [*][7][4] 32 Select Partition 8

33 Activate Local PGM

[20] Zone Assigned

00

Key 1 Key 2 Key 3 Key 4 Key 5

ICON / LED Defaults

Full Message Defaults

KEYPAD 1

KEYPAD 2

KEYPAD 3

KEYPAD 4

KEYPAD 5

KEYPAD 6

KEYPAD 7

KEYPAD 8

Partition/

Slot

11 00 03 04 06 14 16

18 00 03 04 06 14 16

[001]-[004] Zone Definitions

00 Null Zone (Not Used) 12 24 Hour Holdup* 25 Interior Delay* 01 Delay 1* 13 24 Hour Gas* 26 24 Hour Non-alarm* 02 Delay 2* 14 24 Hour Heating* 29 Auto Verified Fire 03 Instant* 15 24 Hour Auxiliary* 30 Fire Supervisory 04 Interior* 16 24 Hour Panic* 31 Day Zone* 05 Interior, Stay/Away* 17 24 Hour Emergency* 32 Instant Stay/Away* 06 Delay, Stay/Away* 18 24 Hour Sprinkler* 35 24-hour Bell/Buzzer 07 Delayed 24 Hour Fire (Hardwired)** 19 24 Hour Water* 36 24 Hour Non-Latching Tamper Zone 08 Standard 24 Hour Fire (Hardwired) 20 24 Hour Freeze* 37 Night Zone 09 24 Hour Supervisory 21 24 Hour Latching Tamper* 87 10 24 Hour Supervisory Buzzer* 22 Momentary Keyswitch Arm* 88 Standard 24 Hour Fire (Wireless/Addressable)** 11 24 Hour Burglary* 23 Maintained Keyswitch Arm*

*For burglary applications only ** For residential fire applications only

Delay 24 Hour Fire (Wireless/Addressable)**

28

5.2 Programming Worksheets

Section Zone Def. Section Zone Def. Section Zone Def. Section Zone Def.

[001]

01 01

02 03

03 03

04 03

05 04

06 04

07 04

08 04

09 00

10 00

11 00

12 00

13 00

14 00

15 00

16 00

I_____I_____I

[002]

17 00

18 00

19 00

20 00

21 00

22 00

23 00

24 00

25 00

26 00

27 00

28 00

29 00

30 00

31 00

32 00

I_____I_____I

[003]

33 00

34 00

35 00

36 00

37 00

38 00

39 00

40 00

41 00

42 00

43 00

44 00

45 00

46 00

47 00

48 00

I_____I_____I

[004]

49 00

50 00

51 00

52 00

53 00

54 00

55 00

56 00

57 00

58 00

59 00

60 00

61 00

62 00

63 00

64 00

[005] System Times

Valid entries for Entry Delay is between 030-255.

[01] Partition 1 Entry/Exit times [05] Partition 5 Entry/Exit times

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

I_____I_____I

[02] Partition 2 Entry/Exit times [06] Partition 6 Entry/Exit times

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

[03] Partition 3 Entry/Exit times [07] Partition 7 Entry/Exit times

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

[04] Partition 4 Entry/Exit times [08] Partition 8 Entry/Exit times

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

030 045 045

I___I___I___I Entry Delay 1 I___I___I___I Entry Delay 2 I___I___I___I Exit Delay

[09] Bell Cut-Off Timer (All Partitions)

003

I___I___I___I Enter 3 digits from 001-255

Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.

29

PowerSeries - PC1616/PC1808/PC1832/PC1864

[006] Installer’s Code [007] Master Code [008] Maintenance Code

Default Default Default

5555 I_______I_______I_______I_______I 1234 I_______I_______I_______I_______I AAAA I_______I_______I_______I_______I

Programmable Output Options

01 Residential Burglary and Fire Bell Output 18 Stay Armed Status 36 Zone Follower Output (Zones 17-24 02 For Future Use 19 Command Output #1 ([*][7][1]) 37 Zone Follower Output (Zones 25-32) 03 Sensor Reset [*][7][2] 20 Command Output #2 ([*][7][2]) 38 Zone Follower Output (Zo n e s 3 3 - 4 0 ) 04 2 Wire Smoke Support (PGM 2 only) 21 Command Output #3 ([*][7][3]) 39 Z o n e F o l l o w e r O u t p u t ( Z o n e s 4 1 - 4 8 ) 05 System Armed Status 22 Command Output #4 ([*][7][4]) 40 Zone Follower Output (Zones 49-56) 06 Ready To Arm 23 24 Hour Silent Input 41 Z o n e F o l l o w e r O u t p u t ( Z o n e s 5 7 - 6 4 ) 07 Keypad Buzzer Follow Mode 24 24 Hour Audible Input 08 Courtesy Pulse 25 Delayed Fire and Burglary Output 09 System Trouble Output (with Trouble options) 26 Battery Test Output 10 System Event [Strobe (with Event options)] 28 Holdup Output 11 System Tamper (all sources: zones, keypad, modules)29 Zone Follower Output (Zones 1-8) 12 TLM and Alarm 30 Partition Status Alarm Memory 13 Kissoff Output 31 Alternate Communicator 14 Ground Start Pulse 32 Open After Alarm 15 Remote Operation (DLS-3 Support) 33 Bell Status and Programming Access Output 16 For Future Use 34 Away Armed with no Zone Bypassed Status

17 Away Armed Status 35 Zone Follower Output (Zones 9-16)

Output types [03] and [20] cannot be used together on the same system.

[009] PGM1 and PGM2 Output Programming (Main Panel)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

PC1616 and PC1832 have 2 onboard PGMs (PGM 1 and 2). PC1864 has 4 onboard PGMs (PGM 1-4)

Default Default

10

I_______I_______I PGM 1 10 I_______I_______I PGM 2

[010] PGM3 to PGM10 Output Programming (Main Panel/PC5208)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

Default Default

05

I_______I_______I PGM 3 (main panel/PC5208)* 01 I_______I_______I PGM 7 (PC5208)

30 I_______I_______I PGM 4 (main panel/PC5208)* 01 I_______I_______I PGM 8 (PC5208) 01 I_______I_______I PGM 5 (PC5208) 01 I_______I_______I PGM 9 (PC5208) 01 I_______I_______I PGM 6 (PC5208) 01 I_______I_______I PGM 10 (PC5208)

These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4 will work the same as the second PC5208 output.

[011] PGM 11 to PGM 14 Output Programming (PC5204)

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]

Default Default

01

I_______I_______I PGM 11 01 I_______I_______I PGM 13

I_______I_______I PGM 12 01 I_______I_______I PGM 14

Other System Options

[012] Keypad Lockout Options

If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.

Default

000

I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes)

I_______I_______I_______I Lockout Duration (001-255 minutes)

30

[013] First System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

[014] Second System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

Normally Closed Loops

R

Double End-of-line Resistors

R

Panel shows all Troubles when armed

9

R

Tampers/Faults do not show as open

R

Auto Arm Schedule in [*][6] and installers

R

Audible Exit Fault Enabled

R

Event Buffer Follows Swinger Shutdown

9

R

Temporal Three Fire Signal Enabled

R

Arm /Disarm Bell Squawk Enabled

R

Bell Squawk During Auto-arm

R

Bell Squawk On Exit Delay

R

Bell Squawk On Entry Delay

R

Bell Squawk On Trouble

R

Audible Exit with Urgency

9

R

Exit Delay Termination Enabled

R

Residential Fire Bell is Continuous

R

End-of-line Resistors

9

R

Single End-of-line Resistors

9

R

Panel shows only Fire Troubles when armed

R

Tampers/Faults show as open

9

R

Auto-arm Schedule in Installer Programming Only

9

R

Audible Exit Fault Disabled

9

R

Event Buffer Logs Events past Shutdown

R

Standard Pulsed Fire Signal

9

R

Arm /Disarm Bell Squawk Disabled

9

R

No Bell Squawk During Auto-arm

9

R

No Bell Squawk On Exit Delay

9

R

No Bell Squawk On Entry Delay

9

R

No Bell Squawk On Trouble

9

R

Silent Exit Delay

R

Exit Delay Termination Disabled

9

R

Residential Fire Bell is Cut-off

9

R

5.2 Programming Worksheets

[015] Third System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

[016] Fourth System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

Fire Key Enabled

9

R

Panic Key Audible (Bell / Beeps)

9

R

Quick Exit Enabled

R

Quick Arming Enabled (No Code Required)

9

R

Code Required for Bypassing

R

Master Code NOT Changeable

R

TLM Enabled

R

TLM Audible (Bell) when Armed

9

R

AC Trouble Displayed

9

R

Trouble Light Flashes if AC Fails

9

R

Blank Keypad when Not Used

R

Code required to remove Keypad Blanking

R

Keypad Backlighting is Enabled

9

R

Power Save Mode Enabled

R

Bypass Status Displayed While Armed

R

Keypad Tampers Enabled

R

9

9 9 9

9 9

9 9 9

Fire Key Disabled

R

Panic Key Silent

R

Quick Exit Disabled

R

Quick Arming Disabled (Code Required)

R

NO Code Required for Bypassing

R

Master Code Changeable

R

TLM Disabled

R

TLM Trouble Beeps when Armed

R

AC Trouble NOT Displayed

R

Trouble Light does NOT follow AC Status

R

Keypad Blanking Disabled

R

No Code Required

R

Keypad Backlighting is Disabled

R

Power Save Mode Disabled

R

Bypass Status NOT Displayed While Armed

R

Keypad Tampers Disabled

R

31

PowerSeries - PC1616/PC1808/PC1832/PC1864

[017] Fifth System Options

Opt Def ON OFF

1

9

2

9

3

4

5

6

7

8

[018] Sixth System Options

Opt Def ON OFF

1

2

3

4

5

9

6

7

8

[019] Seventh System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

WLS Key Does NOT use Access Codes

R

RF Jam Log after 5 Minutes

R

Audible RF Jam Trouble Beeps

R

Double Hit Enabled

R

Late to Close Enabled

R

Daylight Savings Time Enabled

R

For Future Use

R

Squawk on Away Key Arming/Disarming Only

R

Test Transmission Exception Enabled

R

For Future Use

R

For Future Use

R

For Future Use

R

Keypad Buzzer Follows Bell Enabled

R

Cross Zoning Enabled

R

Exit Delay Restart Enabled

R

AC Trouble Beeps Enabled

R

For Future Use

R

Troubles are Latching

R

First Zone in Alarm Enabled

R

For Future Use

R

For Future Use

R

Green Keypad LED Power Indication

R

[4][6] Accessable by All Users

R

For Future Use

R

9 9 9 9 9 9

9 9 9 9

9 9 9

9 9 9 9 9 9 9 9

WLS Key Uses Access Codes

R

RF Jam Log after 30 Seconds

R

Silent RF Jam Trouble Beeps

R

Double Hit Disabled

R

Late to Close Disabled

R

Daylight Savings Time Disabled

R R

Squawk on all Arming/Disarming

R

Test Transmission Exception Disabled

R R R R

Keypad Buzzer Follows Bell Disabled

R

Police Code Enabled

R

Exit Delay Restart Disabled

R

AC Trouble Beeps Disabled

R

Troubles follow restore

R

First Zone in Alarm Disabled

R R R

Ready Indication

R

Master Code Only

R R

Keypad Zone Assignments

[020] Keypad Zone Assignments

Only one keypad may be assigned to a zone.

Default

00 00 00 00

32

I________I_______I Keypad (slot 1) Zone I________I_______I Keypad (slot 2) Zone I________I_______I Keypad (slot 3) Zone I________I_______I Keypad (slot 4) Zone I________I_______I Keypad (slot 5) Zone I________I_______I Keypad (slot 6) Zone I________I_______I Keypad (slot 7) Zone I________I_______I Keypad (slot 8) Zone

Only one keypad may be assigned to a slot. Only one zone can be assigned to a keypad. Valid entries are from 01 to 64.

[021] Eighth System Options

Opt Def ON OFF

1

Access Code Entry Blocked During Entry Delay

R

9

Access Code Entry Not Blocked During Entry Delay

R

5.2 Programming Worksheets

2

3

4

5

6

7

8

[022] Ninth System Options

Opt Def ON OFF

1

2

3

4

5

6

7

8

[023] Tenth System Options

For Future Use

R

For Future Use

R

For Future Use

R

For Future Use

R

Keyswitch Disarming During Entry Delay Only

R

For Future Use

R

For Future Use

R

Access Code Req’d for [4][1], [4][2], [4][3]

R

For Future Use

R

For Future Use

9 R

Master Code Bypasses Holdup Zones Only

R

For Future Use

R

RF Delinquency enabled

R

For Future Use

R

Audible Exit Delay for Stay Arming

R

9 9 9 9 9 9 9

9 9

9 9 9 9 9

R R R R

Keyswitch Disarming at Any Time

R R R

No Access Code Req’d for [4][1], [4][2], [4][3]

R R R

Any Code Bypasses Holdup Zones

R R

RF Delinquency disabled

R R

Stay Arming Silent

R

Opt Def ON OFF

1

2

3

4

5

6

7

8

[030] Zone Loop Response (Zones 1-8)

Opt Def ON OFF

1

2

3

4

5

6

7

8

Fire Key Beeps Only

R

200 Baud Open/Close Identifier Toggle ON

R

Test Transmission While Armed Only

R

Test Transmission in Hours

R

Switching from AWAY to STAY disabled

R

2-way Audio will NOT Disconnect for a New Event

R

Trouble Beeps are Silent*

R

Keyswitch Arm in Away Mode

R

Zone 1 is Fast Loop Response

R

Zone 2 is Fast Loop Response

R

Zone 3 is Fast Loop Response

R

Zone 4 is Fast Loop Response

R

Zone 5 is Fast Loop Response

R

Zone 6 is Fast Loop Response

R

Zone 7 is Fast Loop Response

R

Zone 8 is Fast Loop Response

R

9 9 9 9 9 9 9 9

Fire Key Beeps and Sounds Bell

R

200 Baud Open/Close Identifier Toggle OFF

R

Test Transmission While Armed/Disarmed

R

Test Transmission in Days

R

AWAY to STAY toggle Option Permitted

R

2-way Audio Will Disconnect for a New Event

R

Trouble Beeps Sound Every 10 Seconds

R

Keyswitch arms in STAY or AWAY

R

Zone 1 is Normal Loop Response

R

Zone 2 is Normal Loop Response

R

Zone 3 is Normal Loop Response

R

Zone 4 is Normal Loop Response

R

Zone 5 is Normal Loop Response

R

Zone 6 is Normal Loop Response

R

Zone 7 is Normal Loop Response

R

Zone 8 is Normal Loop Response

R

33

PowerSeries - PC1616/PC1808/PC1832/PC1864

[101]-[164] Zone Attributes

Zone Attribute Defaults (Y = Option ON; N = Option OFF):

Attribute: 123456 789

ON Audible Steady Chime Bypass Force* Swing Tx. Delay Wireless Zn Cross Zn

OFF Silent Pulsed No No No No No No No

Zone Type: 00 Null Zone NNNNNNNNN 01 Delay 1 YYYYNYNNN 02 Delay 2 YYYYNYNNN 03 Instant YYYYNYNNN 04 Interior Y Y N Y N Y N N N 05 Int. Stay/Away Y Y N Y Y Y N N N 06 Dly. Stay/Away Y Y N Y Y Y N N N 07 Dly. 24hr Fire (Hardw.)YNNNNNNN N 08 Stand. 24hr Fire (Hardw.) Y N NNNNNN N 09 24hr Superv. N Y N N Y N N N N 10 24hr Superv. Buzzer N Y N Y N N N N N 11 24hr Burglary Y Y N Y N N N N N 12 24hr Holdup N Y NNNNNN N 13 24hr Gas Y N NNNNNN N 14 24hr Heating Y N NNNNNN N 15 24hr Medical Y Y NNNNNNN 16 24hr Panic Y Y NNNNNNN 17 24hr Emergency Y Y NNNNNN N 18 24hr Sprinkler Y Y NNNNNNN 19 24hr Water Y Y NNNNNNN 20 24hr Freeze Y Y NNNNNN N 21 24hr Latching Tamper Y Y NNNNNNN 22 Momentary Keyswitch N N N N Y N N N N 23 Maintained Keyswitch N N N N Y N N N N 25 Interior Delay YYNYNYNNN 26 24hr Non-alarm N N N N Y N N N N 29 Auto Verified Fire YNNNNNNNN 30 Fire Supervisory NNNNNNNNN 31 Day Zone YYNYYYYNN 32 Instant Stay/Away Y Y N Y N N N N N 35 24 hr Bell/Buzzer Y Y N Y N Y N N N 36 24hr Non Latching Tamper N Y N N N Y N N N 37 Night Zone Y Y N Y Y Y N N N 87 Dly. 24hr Fire (Wireless)YNNNNNNYN 88 Stand. 24hr Fire (Wireless) Y N NNNNNYN

34

Attribute: 10 11 12 13 14 15 16

ON Zone Attributes 10-13 For Future Use NC Loops SEOL DEOL

OFF Config. Config. Config.

Zone Type: 00 Null Zone NNNNNNN 01 Delay 1 NNNNNNN 02 Delay 2 NNNNNNN 03 Instant NNNNNNN 04 Interior NNNNNNN 05 Int. Stay/Away NNNNNNN 06 Dly. Stay/Away NNNNNNN 07 Dly. 24hr Fire (Hardw.) N NNNNNN 08 Stand. 24hr Fire (Hardw.) N NNNNNN 09 24hr Superv. N NNNNNN 10 24hr Superv. Buzzer N NNNNN N 11 24hr Burglary N NNNNNN 12 24hr Holdup N NNNNNN 13 24hr Gas N NNNNNN 14 24hr Heating N NNNNNN 15 24hr Medical N NNNNNN 16 24hr Panic N NNNNNN

5.2 Programming Worksheets

Attribute: 10 11 12 13 14 15 16

ON Zone Attributes 10-13 For Future Use NC Loops SEOL DEOL

OFF Config. Config. Config.

17 24hr Emergency NNNNNNN 18 24hr Sprinkler NNNNNNN 19 24hr Water NNNNNNN 20 24hr Freeze NNNNNNN 21 24hr Latching Tamper NNNNNNN 22 Momentary KeyswitchNNNNNNN 23 Maintained KeyswitchNNNNNNN 25 Interior Delay NNNNNNN 26 24hr Non-alarm NNNNNNN 29 Auto Verified Fire NNNNNNN 30 Fire Supervisory NNNNNNN 31 Day Zone NNNNNNN 32 Instant Stay/Away NNNNNYN 35 24 hr Bell/Buzzer NNNNNNN 36 24hr Non Latching Tamper NNNNNNN 37 Night Zone NNNNNNN 87 Dly. 24hr Fire (Wireless) NNNNNNN 88 Stand. 24hr Fire (Wireless) NNNNNNN

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn

Type** Silent Pulsed No No No No No No No

12345 6789

[101] 01 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [102] 02 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [103] 03 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [104] 04 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [105] 05 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [106] 06 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [107] 07 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [108] 08 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [109] 09 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [110] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [111] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [112] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [113] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [114] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [115] 15 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [116] 16 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[120] 20 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[121] 21 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[122] 22 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[123] 23 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[124] 24 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[125] 25 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[126] 26 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[127] 27 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[128] 28 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[129] 29 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[130] 30 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[131] 31 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[132] 32 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[133] 33 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

35

PowerSeries - PC1616/PC1808/PC1832/PC1864

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn

Type** Silent Pulsed No No No No No No No

12345 6789

[134] 34 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[135] 35 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[136] 36 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[137] 37 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[138] 38 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[139] 39 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[140] 40 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[141] 41 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[142] 42 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[143] 43 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[144] 44 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[145] 45 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[146] 46 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[147] 47 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[148] 48 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[149] 49 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [150] 50 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [151] 51 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [152] 52 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [153] 53 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [154] 54 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [155] 55 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [156] 56 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [157] 57 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [158] 58 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [159] 59 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [160] 60 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [161] 61 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [162] 62 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [163] 63 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I [164] 64 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

Section Zone # Zone For Future For Future For Future For Future NC Loops SEOL DEOL

Type** Use Use Use Use Config. Config. Config.

10 11 12 13 14 15 16

[101] 01 ( ) I________I I________| I________| I________| I________| I________| I________|

[102] 02 ( ) I________I I________| I________| I________| I________| I________| I________|

[103] 03 ( ) I________I I________| I________| I________| I________| I________| I________|

[104] 04 ( ) I________I I________| I________| I________| I________| I________| I________|

[105] 05 ( ) I________I I________| I________| I________| I________| I________| I________|

[106] 06 ( ) I________I I________| I________| I________| I________| I________| I________|

[107] 07 ( ) I________I I________| I________| I________| I________| I________| I________|

[108] 08 ( ) I________I I________| I________| I________| I________| I________| I________|

Zone attributes 10-16 only apply to zones 1-8.

System Timers

[165] Maximum Dialing Attempts to Each Telephone Number

Default 005 I_______I_______I_______I Valid entries are 001-005 attempts

[166] Post Dial Wait for Handshake (All Formats)

Default 040 I_______I_______I_______I Valid entries are 001-255 seconds

36

5.2 Programming Worksheets

[167] T-LINK Interface Communications Wait for Acknowledge

Default 020 I_______I_______I_______I Valid entries are 001-255 seconds

[168] Set Clock Forward (Daylight Saving Time)

Def 004 Month |_______|_______|_______| Valid Entries 001-012

Def 001 Week |_______|_______|_______| Valid Entries 000-005

Def 000 Day |_______|_______|_______| Valid Entries 001-031

Def 002 Hour |_______|_______|_______| Valid Entries 000-023

Def 001 Increment |_______|_______|_______| Valid Entries 001-002

[169] Set Clock Back (Standard Time)

Def 010 Month |_______|_______|_______| Valid Entries 001-012

Def 005 Week |_______|_______|_______| Valid Entries 000-005

Def 000 Day |_______|_______|_______| Valid Entries 001-031

Def 002 Hour |_______|_______|_______| Valid Entries 000-023

Def 001 Decrement |_______|_______|_______| Valid Entries 001-002

[170] PGM Output Timer

Default 005 I_______I_______I_______I Valid entries are 001-255 seconds

[171] Tamper PGM Output Timer

Default 000 I_______I_______I_______I Valid entries are 000-255 minutes

[175] Auto-arm Postpone Timer

Default 000 I_______I_______I_______I Valid entries are 001-255 minutes, 000 disables automatic arming

[176] Cross Zone/Police Code Timer

Default 060 I_______I_______I_______I Valid entries are 001-255 seconds/minutes

Automatic Arming Schedule

Enter a four-digit number (HH:MM) for each day that the system will Auto-arm on each partition (Section [181] for Partition 1 through section [188] for Partition 8). All entries are disabled (9999) by default. Valid entries are 0000-2359.

Sunday Monday Tuesday Wednesday Thursday Friday Saturday

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[181]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[182]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[183]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[184]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[185]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[186]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[187]

I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I I_______I_______I : I_______I_______I

[188]

[190] No Activity Arming Pre-Alert Time

Default Partition

001 All

I_______I_______I_______I Valid entries are 001-255 minutes, 000 for no pre-alert

37

PowerSeries - PC1616/PC1808/PC1832/PC1864

No Activity Arming Timers - Default is [000] for all partitions

Section Partition

[191] 1 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [192] 2I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [193] 3 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [194] 4 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [195] 5 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [196] 6I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [197] 7I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable [198] 8 I_______I_______I_______I Valid entries are 001-255 minutes, 000 to disable

[199] Auto-arming Pre-Alert Timer

Default: 004 I_______I_______I_______I Valid entries are 001-255 minutes

Partition Programming

[201] Partition Selection Mask

Opt Def ON OFF

1

9

2

3

4

5

6

7

8

Partition 1 is enabled

R

Partition 2 is enabled

R

Partition 3 is enabled

R

Partition 4 is enabled

R

Partition 5 is enabled

R

Partition 6 is enabled

R

Partition 7 is enabled

R

Partition 8 is enabled

R

9 9 9 9 9 9 9

Cannot be disabled

R

Disabled

R

Disabled

R

Disabled

R

Disabled

R

Disabled

R

Disabled

R

Disabled

R

For the PC1864 and PC1832 Default is partition 1, zones 1-16 ON. For the PC1808 Default is partition 1, zones 1-8 ON

For the PC1616 Default is partition 1, zones 1-6 ON

Partition 1 Zone Assignment Partition 2 Zone Assignment Partition 3 Zone Assignment Partition 4 Zone Assignment

[202] 1-8

[203] 9-16

[204] 17-24

[205] 25-32

[206] 33-40

[207] 41-48

[208] 49-56

[209] 57-64

Partition 5 Zone Assignment Partition 6 Zone Assignment Partition 7 Zone Assignment Partition 8 Zone Assignment

[234] 1-8

[235] 9-16

[236] 17-24

[237] 25-32

[238] 33-40

[239] 41-48

[240] 49-56

[241] 57-64

RRRRRRRR

[210] 1-8

[211] 9-16

[212] 17-24

[213] 25-32

[214] 33-40

[215] 41-48

[216] 49-56

[217] 57-64

[242] 1-8

[243] 9-16

[244] 17-24

[245] 25-32

[246] 33-40

[247] 41-48

[248] 49-56

[249] 57-64

RRRRRRRR

[218] 1-8

[219] 9-16

[220] 17-24

[221] 25-32

[222] 33-40

[223] 41-48

[224] 49-56

[225] 57-64

[250] 1-8

[251] 9-16

[252] 17-24

[253] 25-32

[254] 33-40

[255] 41-48

[256] 49-56

[257] 57-64

RRRRRRRR

[226] 1-8

[227] 9-16

[228] 17-24

[229] 25-32

[230] 33-40

[231] 41-48

[232] 49-56

[233] 57-64

[258] 1-8

[259] 9-16

[260] 17-24

[261] 25-32

[262] 33-40

[263] 41-48

[264] 49-56

[265] 57-64

RRRRRRRR

38

5.2 Programming Worksheets

When using T-Li nk, program DCAA as the phone number.

Communications

[301] First Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[302] Second Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[303] Third Telephone Number (32 Digits)

I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[304] Call Waiting Cancel String (6 Digits)

I_______I_______I_______I_______I_______I_______I Default = DB70EF Program unused digits with Hex F

- This feature is activated in Section 382 Opt 4

All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’.

Account Codes

Enter a 6-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports 6-digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits.

Section [310] System Account Code DEF [FFFFFF]

I_______I_______I_______I_______I_______I_______I

Enter a four-digit account number for each active partition.

[311] Partition 1 Account Number

[312] Partition 2 Account Number

[313] Partition 3 Account Number

[314] Partition 4 Account Number

[315] Partition 5 Account Number

[316] Partition 6 Account Number

[317] Partition 7 Account Number

[318] Partition 8 Account Number

|_______I_______I_______I_______I

All Account Numbers codes are defaulted to FFFF.

Reporting Codes

[320]-[323] Alarm Reporting Codes, Zones 01-64

All Reporting Codes defaulted to FF unless otherwise indicated.

Section

[320] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

[321] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

[322] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

[323] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

39

PowerSeries - PC1616/PC1808/PC1832/PC1864

[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64

Section

[324] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[325] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[326] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[327] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[328] Miscellaneous Alarm Reporting Codes

I_______I_______I Duress Alarm I_______I_______I Opening After Alarm I___0___I___0___I Recent Closing I_______I_______I Zone Expander Supervisory Alarm I_______I_______I Zone Expander Supervisory Restore I_______I_______I Cross Zone Police Code Alarm I___0___I___0___I Burglary Not Verified I_______I_______I Alarm Cancelled

[329] Priority Alarm and Restoral

I_______I_______I Keypad Fire Alarm

I_______I_______I Keypad Auxiliary Alarm

I_______I_______I Keypad Panic Alarm

I_______I_______I Auxiliary Input Alarm

I_______I_______I Keypad Fire Restoral

I_______I_______I Keypad Auxiliary Restoral

I_______I_______I Keypad Panic Restoral

I_______I_______I Auxiliary Input Restore

[330]-[333] Tamper Reporting Codes, Zones 01-64

Section

[330] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[331] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[332] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[333] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

40

5.2 Programming Worksheets

[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64

Section

[334] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08

[335] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

[336] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

[337] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

[338] Miscellaneous Tamper Reporting Codes

[339]-[340] Closing (Arming) Reporting Codes, Access Codes 1-32

Section

[339] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8

[340] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

[341] Miscellaneous Closing (Arming) Reporting Codes

[342]-[343] Opening (Disarming) Reporting Codes, Access Codes 1-32

Section

[342] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8

[343] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24