DSC PC1404 Description

PC1404 v1.1

Programming Descriptions

PC1404 Programming Descriptions

The following is a description of the programming features and options available in the PC1404 control panel. Note: This manual shall be used in conjunction with the PC1404 Installation Guide (part number 29008503).

[000] Keypad Function Programming

Function Key Description

[00] Null The key is not used and will perform no function when pressed.

[01]-[02] Not Used

[03] Stay Arm Arms the partition to which the keypad is assigned. All stay/away and night type zones will be

[04] Away Arm Arms the partition to which the keypad is assigned. All stay/away and night type zones will be

[05] [*][9] No Entry Arming After this function key is pressed, the user must enter a valid access code. The partition will

[06] [*][4] Door Chime On/Off Pressing the key will toggle the door chime feature on or off. One solid beep means the feature

[07] Not Used

[08] Zone Bypassing When this function key is pressed, the system enters the [*][1] Zone Bypassing menu. If

[09] Trouble Display When this function key is pressed, the system enters the [*][2] Trouble Display menu.

[10] Not Used

[11] User Code Programming When this function key is pressed, the keypad prompts for an access code entry. If the master

[12] User Functions When this function key is pressed, the keypad prompts for an access code entry. If the master

[13] [*][7][1] Command Output This function key provides the user with a simple method of activating a PGM output pro-

[14] [*][7][2] Smoke Detector Reset Pressing this key will cause the panel to deactivate any output programmed as Sensor Reset.

[15] Not Used

[16] [*][0] Quick Exit Pressing this key will cause the panel to activate the Quick Exit feature.

[17] [*][1] Reactivate Stay/Away Zones

[18] Not Used

[19] [*][7][3] Command Output 3 This function key provides the user with a simple method of activating PGMs programmed as

[20] Night Arming The system arms with all Night Zones bypassed, even if the delay zones are violated during

[21] [*][7][4] Command Output 4 This function key provides the user with a simple method of activating a PGM output pro-

[22]-[24] Not Used

automatically bypassed. Delay type zones will provide entry and exit delay. The quick arm feature controls whether an access code must be entered after pressing this function key. The exit delay will be silent if the panel is armed using this function key.

active at the end of the exit delay. Delay type zones will provide entry and exit delay. The quick arm feature controls whether an access code must be entered after pressing this function key. The exit delay will be audible if the panel is armed using this function key.

arm and remove entry delay from the partition when the exit delay expires. The key can be pressed again to enable the entry delay. This function key always requires an access code entry after it has been pressed.

has been disabled, three short beeps means it has been enabled.

desired, the panel can be configured to require an additional access code entry before the system enters zone bypassing

code or an access code with similar permissions is entered, the system enters the [*][5] User Code Programming menu.

code or an access code with similar permissions is entered, the system enters the [*][6] User Functions menu.

grammed as Command Output 1. By default, an access code must be entered after the key is pressed before the output will activate, but this can be changed by disabling PGM attribute 5.

This function key provides the user with a simple method of adding stay/away zones into the system, and it changes the stay armed mode to away armed mode.

Command Output #3. An access code may be required after pressing this key if PGM attribute 5 is enabled.

exit delay. This key only works while the system is disarmed, or armed in the stay mode. The panel logs Armed in Night Mode for this closing type. If no night zone types are programmed on the system, the panel will arm in away mode with an audible exit delay. Normally, no acknowledgement beeps are sounded and the exit delay is silent if this function key is used to arm.The quick arming toggle option controls whether an access code must be entered after the function key is pressed.

grammed as Command Output 4.

PC1404

[25] Instant Stay Arming This feature operates similarly to the stay arming function key except for the following:

When this function key is pressed, no acknowledgement beeps are sounded, there is no exit delay; and the system arms immediately. The panel logs "Armed in Stay Mode" for this closing type. If no stay/away zone types are programmed, the system arms in Away mode with no exit delay.

Note: This function key must not be used in CP-01 listed systems.

[26]-[33] Not Used Not Used.

Zone Programming

Zones 1-8 are enabled by default. Disable unused zones or enable additional zones in Section [001] Zone 1–8 Definitions. The zone definitions describe how each of the zones you use will operate. Program a two-digit code describing the zone definition. Select a definition from the list below. In addition, each zone has 16 different attributes which may be programmed in Sections [101]-[108] Zone Attributes. (See also programming descriptions Section [101]-[108] Zone Attributes)

[001] Zone Definitions

[00] Null Zone

This zone type should be programmed if an input is not going to be used. Programming this zone type should clear any trouble conditions present on the zone input. An EOL resistor is not required for this zone definition.

[01] Delay 1

This zone type, normally used for entry/exit doors, can be violated and restored during the exit delay time without causing an alarm. After the exit delay has expired and the system is armed, violating this zone shall start the entry delay 1 timer. During the entry delay time, the keypad buzzer will sound steadily to advise the user that the system should be disarmed. If the panel is disarmed before the entry time expires, no alarm will be generated.

[02] Delay 2 Zone

This zone type operates the similar to the delay 1 zone; however, it follows a different entry delay timer, defined as Entry Delay 2 in Section [005] System Times. Typically this zone type is used for garage doors or for entry/exit points that require a different delay time than what is being used for the main entry/exit point. The Delay 2 entry delay time can be set independently of Delay 1 in programming Section [005] (System Times).

[03] Instant Zone

This zone type causes an instant alarm if it is violated when the panel is armed; it does not provide an entry delay when violated while armed. This zone type does not generate an alarm when disarmed. Typically, this zone is used for windows, patio doors or other perimeter zones, and glass break detectors.

[04] Interior Zone

Interior zones have an exit delay and an entry delay if a delay zone has been violated first. The zone goes into alarm when the entry delay of the delay type zone has expired if the system has not been disarmed. If the zone is violated without an entry or exit delay being active on the system, an immediate alarm is generated. This zone will not cause an alarm if violated during the entry delay. If the zone is violated before the entry delay has begun, it will cause an instant alarm. Typically, this zone is used for interior protection devices, such as motion detectors.

[05] Interior Stay/Away Zone

If the system is stay armed, this zone is bypassed. If the system is armed in away or night mode, the zone acts like an Interior Zone type [04].

[06] Delay Stay/Away Zone

If the system is stay armed, this zone is bypassed. If the system is armed in away or night mode, this zone acts like a Delay 1 type [01].

[07] Delayed 24-hr Fire Zone

Note: Do not wire Fire zones on keypad zone terminals if the DEOL supervision option is enabled for the panel (Section [013], Option [2]).

This zone type requires a SEOL resistor, and it cannot be reconfigured using the NC, EOL or DEOL options in the panel. The alarm state is short, the restored state is 5k6, and an open condition will generate a zone tamper and fire trouble. When this zone i the alarm output will be immediately activated (pre-alert) but the communicator will be delayed for 30 seconds. If the alarm is acknowledged by pressing any key during this delay or by tripping a keyswitch zone, the alarm output and the communicator will be delayed an additional 90 seconds, giving the user time to correct the problem. If the zone is still violated after the 90 second delay, the sequence will repeat. If the user does not press a key during the 30 second pre-alert, the alarm output will latch and the panel will communicate the alarm to the central station. The alarm will sound until the Bell Cutoff time expires ([005] System Times) or until a code is entered.

Note: If a second Fire type zone is violated or if the Fire keys are pressed during the delay period, the panel will latch the alarm output and will immediately communicate the alarm.

A violated Fire zone will be displayed on all keypads and can be delayed at any keypad. Typically this zone is used for latching smoke detectors.

s violated,

PC1404 Programming Descriptions

[08] Standard 24-hr Fire Zone (hardwired)

Note: Do not wire Fire zones on keypad zone terminals if the DEOL supervision option is enabled for the panel (Section [013], Option [2]).

This zone type requires a SEOL resistor, and it cannot be reconfigured using the NC, EOL or DEOL options in the panel. The alarm state is short, the restored state is 5k6, and an open condition will generate a zone tamper and fire trouble. When violated, the bell output will sound a pulsing alarm tone to indicate that the fire loop has been activated. If enabled, the communicator will immediately send an alarm to the central station.The alarm will sound until the Bell Cutoff time expires (Section [005] “System Times”), or until a code is entered. A violated Fire zone will be displayed on all keypads. Typically this zone is used for pull stations.

[09] 24-hr Supervisory Zone

This zone type requires a SEOL resistor, and it cannot be reconfigured using the NC, EOL or DEOL options in the panel. The restored state of this zone is 5.6k, the alarm state is short and the tamper state is open. This zone does not cause the bell to activate, but will be displayed in alarm memory regardless of the armed state of the panel. If this zone is violated when the system is either armed or disarmed, the panel will report to the central station, and will log the zone alarm to the event buffer. This zone gives a silent alarm by default.

Note: Do not wire 24-hr Supervisory zones on keypad zone terminals.

[10] 24-hr Supervisory Buzzer Zone

If this zone is violated when the system is either armed or disarmed, the panel will immediately latch the keypad buzzer until a valid access code is entered and will immediately communicate to the central station.

[11] 24-hr Burglary Zone

If this zone is violated when the system is either armed or disarmed, the panel will immediately latch the alarm output and communicate to the central station. The alarm will sound until the Bell Cutoff time expires (Section [005] “System Times”), or until a code is entered.

[12] Not Used

[13] 24 Hr. Gas

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, pulsing alarm. This zone type is typically used with CO detectors or for monitoring gas lines.

[14] 24 Hr. Heat

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used with heat detectors.

[15] 24 Hr. Medical

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used for medical emergency pull stations.

[16] 24 Hr. Panic

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used with panic pendants.

[17] 24 Hr. Emergency

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used for non-medical emergency situations.

[18] Not Used [19] 24 Hr. Water

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used for monitoring flood conditions.

[20] 24 Hr. Freeze

This zone type is active at all times, regardless of the armed state, and when tripped will generate an audible, steady alarm. This zone type is typically used in applications that monitor low temperatures.

[21] 24-hr Latching Tamper

This zone type, when violated, will cause arming of the system to be inhibited until the installer accesses Installer Programming or the condition has been reset using DLS. This zone type is normally used for monitoring the panel's cabinet. If the cabinet has been opened, someone may have tampered with the system's wiring, so this zone type is used to generate an installer service call. This zone type generates an audible, steady alarm in both armed and disarmed states.

[22] Momentary Keyswitch Arm Zone

A keyswitch device (mechanical switch controlled by a key) may be connected to the zone input programmed as momentary keyswitch. Momentary activation (open and close) of the zone alternately arms/disarms the system and silences alarms. Tampers and faults will only initiate their respective trouble sequence. The keypad will not display an indication when this type of zone is activated. When an audible alarm is active, using the keyswitch when disarmed is the same as entering an access code at the keypad. The system will log special closing or special opening if the keyswitch is used for arming/disarming. If a keyswitch device is bypassed, the bypass must be manually removed.

[23] Maintained Keyswitch Arm Zone (Hardwired)

A keyswitch device (mechanical switch controlled by a key) may be connected to the zone input programmed as maintained keyswitch. In the restored state, the system is disarmed. In the violated state, the panel will arm. Tampers and faults will only initiate their respective trouble sequence. The keypad will not display an indication when this type of zone is activated. If the system is armed using this zone (violated), but the system is disarmed using a different method, the keyswitch must be restored and violated again to start a new arming sequence. The same is true for disarming.

A bypass of this zone type must be manually removed.

PC1404

With an audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad. Activating this zone type during the first 30 seconds of a delayed fire alarm is the same as entering an access code at the keypad (the 90 second delay will start). If left in the violated state, the system will not arm until the zone is restored and violated again.

[24] Not Used

[25] Interior Delay Zone

This zone type is normally used with interior motion detectors and has a standard exit delay time. If the panel is armed in away or night mode, the interior delay zone will be active at the end of exit delay. The zone then acts like an Interior zone [04]. If the system is armed in stay mode, the zone behaves like a delay 1 zone. Violating this zone during exit delay will not cause the system to arm in away mode like regular delay 1 zones do.

[26] 24 Hour Non-Alarm (or local alarm) Zone

Zones programmed as this type are active at all times but do not cause an alarm, and are not saved in alarm memory. Zone attributes such as Zone Bypassing and Door Chime affect the functionality of this zone. Typically, this zone type is used in conjunction with a zone follower PGM to trigger an output when violated but not cause alarm conditions.

Note: This zone type sounds the bell but does not communicate during a walk test. Tampers and faults on zones programmed as 24Hour non-alarm type do not cause alarms.

[27]-[28] Not Used [29] Auto-Verified Fire

This zone type is used with hardwired smoke detectors. This zone definition will ensure that an alarm condition persists by removing power to a smoke detector in the alarm state. When the power is restored after 20 seconds, the system will check the state of the zone again. If the zone is still violated, the system will sound a pulsing alarm using the system siren and will communicate the alarm to the monitoring station.

Auto-verify Alarm Sequence: Step 1 - Perform a 20 second sensor reset (remove power to smoke detector). Step 2 - Allow 10 seconds for devices to settle. Step 3 - Check for verified alarm for 60 seconds. This zone is used for CP-01 and UL/ULC Fire Monitoring applications. If a secondary fire alarm is detected at any time during the above delay sequence, the auto-verify sequence is immediately terminated and alarms are generated for all pending fire alarms.

[30] Not Used [31] Day Zone

Violating this zone when disarmed sounds the keypad buzzer but does not log or report the events. Violating this zone when armed sounds the bell and communicates the event.

[32] Instant, Stay-Away Zone

This zone is bypassed when the system is Stay armed or disarmed, but it functions similarly to an Instant Zone [03] when Away or Night armed. This zone type is useful for motion detectors that must NOT follow the entry delay after a delay zone is violated, but must still retain the Stay/Away functionality.

[33]-[34] Not Used

[35] 24-Hr. Bell/Buzzer

This zone type will behave like a 24 hour burglary zone when armed and a 24 hour buzzer zone while disarmed. When the panel is armed, the siren will activate for the duration of bell time out when this zone is violated. When the panel is disarmed, the keypad buzzers will latch until a valid disarming procedure is used.

[36] 24-Hr. Non-Latching Tamper

This zone type is always active and will report a tamper condition if the panel is armed or disarmed. The communications generated for this zone type do not follow transmission delay. In DEOL configuration, a tamper or open condition will generate a tamper event. A short condition will generate a fault event.

[37] Night Zone

This zone type is bypassed if the panel is disarmed, armed in stay mode or armed in night mode. It is active in the armed state and behaves like an Interior zone. If entry delay is active, the zone type will not create an alarm until the entry delay expires. If violated while away armed, but entry delay isn't active, the zone will generate an instant alarm.

[41] 24-Hr. CO Zone (hardwired)

This zone definition is only to be used with hardwired carbon monoxide detectors. The zone is active in all armed states. This zone definition has its own bell cadence. The siren shall sound 4 cycles of 100mS On/Off pulses, followed by a 5 second pause and then the sequence repeats. After four minutes, the 5 second pause will be extended to a 60 second pause. The bell will be silenced upon bell time out or when a code has been entered at the keypad. No bell delay or transmission delay will affect this operation. Tampers and faults from a CO zone type will not impede arming. If a CO zone is in Device Fault, the control panel will sound CO cadence. This is different when compared to a low sensitivity fault in a smoke detector, which will not generate an alarm. A tamper restore must be created on the device to remove any device faults, which will prevent run-away transmission from a device going in and out of fault.

[81]-[88] Not Used

PC1404 Programming Descriptions

[005] System Times

Enter Section [005] then Subsection [01] to program the Entry Delay 1, Entry Delay 2 and Exit Delay for the system. Entries are in seconds. A value of 000 in the entry or exit delay sections causes a 255 second delay; however, the time is displayed as 000. Enter Section [005] then Subsection [09] to program the Bell Cut-Off Time. Valid entries are in minutes. A value of 000 in the BTO section produces a 1 minute bell cut-off time. However, this time is displayed as 000.

[006] Installer Code

The default Installer Code is [5555] or [555555] if 6-digit access codes is enabled.

[007] Master Code

The default Master Code is [1234] or [123456] if 6-digit access codes is enabled.

[008] Maintenance Code

The Maintenance Code is a system user code that can only arm and disarm. Any other system function that requires an access code is not accessible by this code. The default Maintenance code is [AAAA] or [AAAAAA] if 6-digit access codes are programmed. See [701] First International Options Opt. 5.

[009]–[011] PGM Programming (Zones/PGMs)

Program the programmable outputs PGM 1 and PGM 2 on the main board and on PC5208 and PC5204 by selecting one of the output options listed below (exceptions noted)].

PGM Output Options

01 Burglary and Fire Bell Output. This output will activate when the siren output is active and will turn off when the alarm

output deactivates. If the siren is sounding a pulsing alarm, the PGM output will pulse as well. This PGM will follow:

• Fire alarm pre-alert

• Temporal three fire signal (if enabled)

• All burglary and fire alarms

• Bell cut-off time This output does will NOT activate for siren squawk events of any type.

Fire alarms take precedence over burglary. Therefore, if the PGM is indicating a steady burglary alarm, and a fire alarm occurs, the PGM will follow a pulsing cadence. If the PGM is already on when a silent alarm occurs, the output will remain on.

02 Not Used

03 Sensor Reset. This output is normally active (switched to ground). This option is used to remove and restore power for latch-

ing smoke detectors. The output will deactivate for 5 seconds when the [*][7][2] command is entered (refer to [*][7] command outputs). When this PGM is programmed, the PGM output is normally low, which is the opposite of how most PGMs operate at default. This is because the PGM is used as the negative return for power to 4-wire smoke detectors (positive comes from the Aux + terminal). To activate this output and reset smoke detectors, [*][7][2] must be entered at the keypad or an equivalent function key must be used. The PGM terminal will go high (open circuit) and thus remove power from the devices connected.

04 2-Wire Smoke. When this PGM is programmed, the onboard PGM 2 functions as an input instead of an output. It behaves

much like the sensor reset PGM in that it is normally low supplying the negative return. Two-wire smoke devices can be connected to this input. The PGM is also supervised, and a trouble condition is generated if a 2.2K resistor is not present between the PGM terminal and AUX+. The two-wire smoke detector input creates an instant and latching alarm.

05 System Armed Status. This output will activate (switch to ground) when the system is armed and will deactivate when dis-

armed. Depending on the market, the panel may turn off this PGM when keypad blanking is active.

06 Ready to Arm. The PGM switches to ground when the system is ready to arm (all non-force armable zones on the system are

restored). When an access code is entered to arm the system and the exit delay begins, the PGM output is de-activated. This PGM operates as described during walk test mode (if all zones are restored).

07 Keypad Buzzer Follow. The PGM output switches to ground when the keypad buzzer is activated by the events described

below:

• 24-hour supervisory buzzer zone alarm • Auto-Arm or No activity arm pre-alert

• Entry delay • Audible exit delay

• Door chime The PGM output remains switched to ground while the keypad buzzer is active. This PGM type does not activate for local key presses or trouble beeps.

08 Courtesy Pulse. This PGM output switches to ground for 2 minutes past the end of entry or exit times to allow enough time

for complete entry to or exit from the premises. This option can also be used to turn on a light along the entry/exit route during the entry or exit delay times. If the system is armed through the No Activity Arming method this output will NOT activate.

PC1404

1 Burglary

2 Fire

3 Panic

4 Medical

5 Supervisory

6 Priority

7 Not Used

8 Latched

Delay, Instant, Interior, Stay/Away and 24-Hour Burg. zones

Key, Fire zone

Key and Panic zone

Auxiliary Key, Medical and Emergency zones

Supervisory, Freezer and Water zones

Gas, Heat, Sprinkler and 24-Hour Latching zones

Output Follows Pulse timer/Output Latching

PGM Output Options

09 System Trouble. This PGM output switches to ground when any of the selected Troubles are detected. The output de-acti-

vates when all of the selected Troubles are restored. The PGM attributes for this output are unique for this PGM type and the standard attributes do not apply. The PGM attributes for this output are as follows:

1 Service Required

5 Fire Trouble/Zone Fault

2 A.C. Failure 6 Zone Tamper

3 Telephone Line Fault 7 Future Use

4 Communications (Failure to Communicate) 8 Loss of Clock

Note: * = Battery, Bell circuit, General System Trouble, General System Tamper, General System Supervisory Troubles,

PC5204 Low Battery and PC5204 AC Fail

10 System Event Output. This PGM output switches to ground when any of the selected system events (alarms) occur on the sys-

tem. In the armed state, the output will deactivate only once the system is disarmed. If an alarm causes this output to activate in the disarmed state, the output will deactivate if a user enters a valid access code while the bell is still active. If BTO has occurred, the PGM will deactivate if someone arms the system after the bell cut-off has expired. This output can be used to indicate that an alarm has occurred before entering the premises. The PGM attributes for this output are unique and the standard attributes do not apply. Program the events that will activate the output by selecting some or all of the following PGM attributes:

Note: This PGM output activates for alarm conditions only. Pre-alerts or delays do NOT activate the output. When this output

follows the output timer, events that have been disabled from activating the output do not restart the timer.

11 System Tamper. This PGM output switches to ground when any Tamper condition occurs on the system and deactivates when all

Tamper conditions on the system are cleared. These tampers include zone tampers (DEOL), 24 Hr Latching or Non-latching Tamper Zones, module tampers and keypad tampers. This output will also activate for the following events): Bell Circuit Trouble, TLM Trouble, Keybus Fault, Zone Expander Supervisory, General System Supervisory, and General System Tamper.

12 TLM and Alarm. The output activates when a Telephone Line Trouble (TLM) condition is present followed by an alarm

condition. The output will remain active until an access code is entered to disarm the partition. The output will activate for all audible and silent alarms except for duress if a TLM trouble is present at the time of the alarm. If an alarm activates this output in the disarmed state, it will deactivate when the system is armed or the telephone line trouble is restored.

13 Kiss-off. This output will activate (switch to ground) for two seconds after the panel receives the kiss-off signal from the cen-

tral station receiver.

14 Ground Start. This PGM output is used for old telephone systems where Tip and Ring need to be shorted together briefly to

get dial tone. The output will activate for two seconds before the panel attempts dialing to obtain a dial tone on Ground Start telephone equipment. Two 2-second pauses (hex E) must be inserted at the beginning of the telephone number when using this option.

15 Remote Operation. This output can be activated or deactivated remotely by using DSC's Downloading Software.

16 Not Used

17 Away Armed Status. This output will activate at the beginning of exit delay when the system is armed using away mode.

18 Stay Armed Status. This output will activate when the system is armed with the stay/away zones bypassed.

PGM output types [17] and [18] are designed to follow the status of the stay/away zones. If the system is armed with stay/ away zones bypassed, the stay output should be active. If the system is armed with the stay/away zones active, the AWAY armed status PGM will turn on. The following indicates how these arming techniques work: STAY key Stay [*][9] + Code Stay AWAY key Away Keyswitch Arm Depends on delay type zone during exit delay [*][0] Quick Arm Depends on delay type zone during exit delay Access Code Arm Depends on delay type zone during exit delay DLS Arm Away Auto Arm Away Stay Armed, then [*][1] Away

PC1404 Programming Descriptions

PGM Output Options

19 Command Output #1. This output is activated by entering the [*][7][1] command. The configuration of the corresponding

attributes determines how this PGM will activate. Command outputs 1-4 are user initiated by entering [*][7][1-4] at any keypad. When any output is activated, three ack beeps will be sounded by the keypad. This feature is User controlled. This function can be performed when a Programmable Output is programmed as Type [19]. This output can be used for operating devices such as garage door opener, special lighting or door strikes.

Note: If there are multiple outputs programmed with the same PGM type, the PGM attributes must be the same for each of them.

20 Command Output #2. This output is activated by entering the [*][7][2] command. The configuration of the corresponding

attributes determines how this PGM will activate. Only one sensor reset or command output #2 PGM can be programmed on the system. This feature is User controlled. This function can be performed when a Programmable Output is programmed as Type [03] or Type [20], but not both. This output can be used to reset all smoke detectors on the system (2-Wire and 4-Wire).

21 Command Output #3. This output is activated by entering the [*][7][3] command. The configuration of the corresponding

attributes determines how this PGM will activate. This feature is User controlled. This function can be performed when a Programmable Output is programmed as Type [21]. This output can be used for operating devices such as garage door opener, special lighting or door strikes.

22 Command Output #4. This output is activated by entering the [*][7][4] command. The configuration of the corresponding

attributes determines how this PGM will activate. This feature is User controlled. This function can be performed when a Programmable Output is programmed as Type [22]. This output can be used for operating devices such as garage door opener, special lighting or door strikes.

23-24 Not Used

25 Delayed Fire and Burg Output. This programmable output type operates the same as the fire and burglary output (PGM type

01), except that it follows the transmission delay timer programmed in Section [377]. If a zone is violated that has the transmission delay attribute enabled (bit 7), the Bell and Regular Fire and Burg PGMs will activate. At the end of the transmission delay, the delayed fire and burg output will activate. This PGM is usually used to control outdoor sirens: if a "false" alarm occurs on the panel, the user has the duration of transmission delay to disarm the system before the external sirens activate.

Note: If a zone is violated that causes an alarm, but does not follow transmission delay, this PGM will activate immediately, even if transmission delay is active for a different zone alarm.

Note: This output activates for audible exit fault.

26 Not Used

27 Police Code Output. When the police code event occurs, this output will activate until the panel is either armed or disarmed.

If police code is not configured to communicate, the PGM will still activate for the event.

29 Zone Follower 1-8. This output type is normally active and allows an output to deactivate for the duration that a zone is violated.

The PGM attributes are programmed through an 8 bit toggle mask that selects which zones the output will follow. The toggle mask is programmable in Sections [551-564]. Example: If PGM is programmed as Type 29 with extended attributes 1, 6 and 8 ON, the output will turn off when any of the three zones are violated, and will restore when all three zones are restored.

30 Status Alarm Memory Output. This feature is intended to be used on a keyswitch plate, with a light controlled by this PGM

to indicate system status. The status alarm memory output will activate (steady) at the beginning of exit delay, when the partition is armed. If an alarm occurs on the armed partition, the output will flash (1 sec ON/1 sec OFF) for the remainder of the armed period. If an alarm occurs on a disarmed partition (24 Hr Zone), the output will flash (1 sec ON/1 sec OFF) until the alarm is acknowledged (bells are silenced during BTO, or the partition is armed after BTO). This output will not activate in walk test.

[012] Keypad Lockout Options

This section determines how the keypad function operates. The panel can be configured to "lockout" keypads if a series of incorrect access code entries are made.

Number of Invalid Codes Before Lockout

Program a number from 001 to 255 to determine the number of invalid master, user or installer access code entries to reach keypad lockout. When keypad lockout occurs, the system is rendered inoperative via the keypad for the programmed duration only (keyswitch zones still function). When any keys are pressed, an error tone sounds. Entering 000 disables keypad lockout.

Lockout Duration

Program a time from 001 to 255 minutes to determine the length of time before lockout resets and the keypad can once again be used.

• If lockout is not reached within the hour roll-over (01:59 to 02:00 for example), the number of invalid attempts is reset to 0.

• After a valid access code is entered, the number of invalid attempts is reset to 0.

• Fire, Auxiliary and Panic keys are still active during keypad lockout.

• Key presses do not reset the timer.

• If the lockout timer was active before powering down, the system lockout is active for the programmed duration on power up.

PC1404

[013] First System Options

Option Description

[1]

Zone Loop Typ e

[2]

End-ofLine Option

[3]

Trouble Display

[4]

Tamper/ Fault Display

[5]

AutoArm Schedule

[6]

Audible Exit Fault

[7]

Zone Doubling

[8]

Fire Signaling

ON: Normally Closed Loops. All zones are wired as normally closed circuits with returns connected to a COM terminal.

The end-of-line resistor is not required. An alarm will be generated when the circuit is opened. OFF: End-of-Line Resistors. All zones must be wired with an end-of-line resistor configuration, determined by Option 2 in Section [013].

ON: Double End-of-Line Resistors. All zones will use Double End-of-Line resistors, except Standard Fire, Delayed Fire and 24 Hr Supervisory. These zones must be connected using the EOL resistor. Double EOL resistors enable the detection of zone faults and tampers. The tamper resistor (5k6) is placed across the alarm activating device, and the single EOL resistor (5k6) is placed between the alarm and tamper contacts. This configuration will allow the panel to detect zone faults (zone shorted), zone tampers (open zone), zone alarms (11.2k) and restored zones (5k6). If the zone/system is disarmed and placed in the tamper or fault state, trouble beeps will be generated on all system keypads until a key is pressed. If the zone is armed and a tamper is activated, the tamper alarm and zone alarm will be logged and transmitted. The zone will begin the normal alarm sequence (bells, alarms in memory, etc.). OFF: Single End-of-Line Resistors. All zones must have a 5k6 resistor across the terminals. If the zone is shorted or opened, it will be treated as a violated state. If the zone is open and programmed as a fire zone, it will be in the trouble state.

ON: Panel Shows All Troubles While Armed. The panel will activate the trouble LED in both the armed and disarmed state when any trouble is present on the system. OFF: Panel Shows Fire Troubles While Armed. The panel will activate the trouble LED for all troubles while disarmed, but the LED will only activate for Fire Troubles while the system is armed.

ON: Tampers and Faults Do Not Show As Open. The panel will not activate the respective Zone LED if the zone is in the tamper or fault states, only the Trouble LED will be on. OFF: Tampers and Faults Show as Open. The panel will illuminate the respective Zone LED (LED Keypads) if the zone is in the tamper or fault state.

ON: Auto-Arm Schedule in [*][6]. The auto-arm schedules (Section [181]) are accessible via [*][6] as well as Installer Programming. OFF: Auto-Arm Schedule in Installer Programming Only. The auto-arm schedules (Section [181]) are only accessible via Installer Programming.

ON: Audible Exit Fault is Enabled. If a delay type zone is violated or is still violated within 4 seconds after the exit delay has expired, the panel will sound the entry delay warning through the keypad and siren alerting the customer that an improper exit was made. If the panel is disarmed within the entry delay, no signal is sent. If not, the panel will continue to sound the alarm and send a signal to central station. Audible Exit Fault Pre-Alert will be logged when the entry delay begins, and audible exit fault will be logged and communicated when the exit delay expires. OFF: Audible Exit Fault is Disabled. The siren will not activate during the entry delay created by leaving a delay zone violated when exit delay expires.

ON: Zone Doubling Enabled. When the Zone Doubler option is enabled on a PC1404, Zone 1 will become Zones 1 and 5, Zone 2 will become Zones 2 and 6, and so on, up to 8 hardwired zones. The 4 zones on the main board now act as 8 zone inputs. When enabled, Options 1 and 2 in Section 013 are ignored. Keypad Zones should not be used on zones designated for Zone Doubling (PC1404: Zones 1-8). Fast Loop Response Feature (Section 030) will not work when Zone Doubling is enabled. Note: Only normally closed devices may be used with zone doubling. Note: A fault condition from either zone will create a zone fault trouble for both zones.

OFF: Zone Doubling is Disabled.

The 4 zones on the main board act as 4 zone inputs.

ON: Temporal 3 Fire Signal. To comply with NFPA 72, all Fire Bells will sound the temporal 3 fire cadence as described in the NFPA standard if this option is enabled. The cadence is 500ms ON, 500ms OFF, 500ms ON, 500ms OFF, 1.5 sec OFF. OFF: Standard Pulsing Fire Signal. All fire bells will sound with the standard 1 second ON/1 second OFF fire bell cadence.

[014] Second System Options

Option Description

[1]

Bell Squawk

[2]

Bell Squawk for AutoArming

[3]-[6] Future Use

ON: Arm/Disarm Bell Squawk Enabled. The system squawks the bell output once when armed (including auto-arming) and twice when disarmed. If there are alarms in memory, 3 distinct squawk pairs will sound (6 squawks in total).

OFF: Arm/Disarm Bell Squawk Disabled. Bell output does not activate when the system is armed or disarmed in any manner.

ON: Bell Squawk For Auto-Arming Enabled. The bell output will sound a single squawk every 10 seconds during the

auto-arm pre-alert time. This also applies to no activity arming pre-alerts. OFF: Bell Squawk For Auto-Arming Disabled. The bell output will not be activated during auto arming or no activity arming pre-alerts.

+ 18 hidden pages

DSC PC1404 Description

Specifications and Main Features

Frequently Asked Questions

User Manual