Dodge Avenger 2013 User Manual

Download

Page 1

AVENGER

USER GUIDE

2013

Page 2

If you are the ﬁrst registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Uconnect® Manuals or Warranty Booklet by calling 1-800-423-6343 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer.

IMPORTANT

This User Guide is intended to familiarize you with the important features of your vehicle.

The DVD enclosed contains your Owner’s Manual, Navigation/Uconnect Booklets, Tire Warranty and Roadside Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you

The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road. Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous and could lead to a serious collision. Texting while driving is also dangerous and should never be done while the vehicle is moving. If you ﬁnd yourself unable to devote your full attention to vehicle operation, pull off the road to a safe location and stop your vehicle. Some States or Provinces prohibit the use of cellular telephones or texting while driving. It is always the driver’s responsibility to comply with all local laws.

Manuals, Warranty

Page 3

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC . . . 2

CONTROLS AT A GLANCE

DRIVER COCKPIT ................4

INSTRUMENT CLUSTER .............6

GETTING STARTED

KEYFOB .....................8

REMOTE START .................9

THEFT ALARM .................9

SEATBELT ....................9

SUPPLEMENTAL RESTRAINT SYSTEM

(SRS)—AIRBAGS................10

CHILD RESTRAINTS ..............11

FRONT SEATS .................14

REARSEATS ..................15

HEATEDSEATS .................16

TILT/TELESCOPING STEERING COLUMN . . . 17

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS . . . 18

TURN SIGNAL/LIGHTS LEVER .........18

WIPER/WASHER LEVER ............20

SPEED CONTROL ................21

MANUAL CLIMATE CONTROLS ........22

AUTOMATIC TEMPERATURE CONTROLS

(ATC) ......................22

POWER SUNROOF ...............24

WIND BUFFETING ...............25

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM ......26

Uconnect® 130 .................28

Uconnect® 130 WITH SiriusXM SATELLITE

RADIO......................30

Uconnect® 430/430N .............33

Uconnect® 730N ................42

SiriusXM SATELLITE RADIO/TRAVEL LINK . . 52

STEERING WHEEL AUDIO CONTROLS ....55

iPod®/USB/MP3 CONTROL ..........55

Uconnect® Phone ...............56

Uconnect® VOICE COMMAND .........59

Bluetooth® STREAMING AUDIO ........62

ELECTRONIC VEHICLE INFORMATION

CENTER (EVIC) .................62

PROGRAMMABLE FEATURES .........63

UNIVERSAL GARAGE DOOR OPENER

(HomeLink®) ..................64

POWER OUTLET ................66

UTILITY

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) . . . 68 RECREATIONAL TOWING

(BEHIND MOTORHOME, ETC.) .........69

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE ............70

INSTRUMENT CLUSTER WARNING LIGHTS . . 70

IF YOUR ENGINE OVERHEATS .........74

JACKING AND TIRE CHANGING ........75

BATTERY LOCATION ..............80

JUMP-STARTING ................80

SHIFT LEVER OVERRIDE ...........82

TOWING A DISABLED VEHICLE ........83

FREEING A STUCK VEHICLE .........83

EVENT DATA RECORDER (EDR) ........84

MAINTAINING YOUR VEHICLE

OPENING THE HOOD ..............85

ENGINE COMPARTMENT ...........86

FLUIDS AND CAPACITIES ...........88

MAINTENANCE SCHEDULE ..........90

MAINTENANCE RECORD ...........93

FUSES ......................94

TIRE PRESSURES ...............96

WHEEL AND WHEEL TRIM CARE .......96

EXTERIOR BULBS ...............97

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC

CUSTOMER CENTER .............98

CHRYSLER CANADA INC.

CUSTOMER CENTER .............98

ASSISTANCE FOR THE HEARING

IMPAIRED ...................98

PUBLICATIONS ORDERING ..........98

REPORTING SAFETY DEFECTS IN THE

UNITEDSTATES ................99

MOPAR ACCESSORIES

AUTHENTIC ACCESSORIES BY MOPAR® . . 100

INDEX

....................101

FAQ (How To?)

FREQUENTLY ASKED QUESTIONS ......103

Page 4

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place. Always drive carefully.

Your new vehicle has many features for the comfort and convenience of you and your passengers. Some of these should not be used when driving because they take your eyes from the road or yourattention from driving. Never text while driving or takeyour eyes more than momentarily off the road.

This guide illustratesand describes theoperation of featuresand equipment that are either standard or optional on this vehicle. This guide may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this guide that are not available on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

This User Guide has been prepared to help you quickly become acquainted with the important features of your vehicle. It contains most things you will need to operate and maintain the vehicle, including emergency information.

The DVD includes a computer application containing detailed owner's information which can be viewed on a personal computeror MAC computer.The multimedia DVD alsoincludes videos which can be played on any standard DVD player (including the Uconnect® TouchScreen Radios). Additional DVD operational information is located on the back of the DVD sleeve.

For complete owner information, refer to your Owner's Manual on the DVD in the owner’s kit provided at the time of new vehicle purchase. For your convenience, the information

contained on the DVD may also be printed and saved for future reference.

Chrysler Group LLC is committed to protecting our environment and natural resources. By converting from paper to electronic delivery for the majority of the user information for your vehicle, together we greatlyreducethe demand for tree-based productsand lessen the stress on our environment.

Page 5

INTRODUCTION/WELCOME

VEHICLES SOLD IN CANADA

With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution.

WARNING!

• Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.

• Always make sure that objects cannot fall into the driver foot well while the vehicleis moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control.

• Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle.

• Never use the ‘PARK’ position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.

• Refer to your Owner's Manual on the DVD for further details.

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

The use of aftermarket devices including cell phones, MP3 players, GPS systems, or chargers may affect the performance of on-board wireless features including Keyless Enter-N-Go™ and Remote Start range. If you are experiencing difficulties with any of your wireless features, try disconnecting your aftermarket devices to see if the situation improves. If your symptoms persist, please see an authorized dealer.

CHRYSLER, DODGE, JEEP, RAM TRUCK, SRT, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC.

Page 6

CONTROLS AT A GLANCE

DRIVER COCKPIT

Page 7

(EVIC) Controls pg. 62

L. Electronic Vehicle Information Center

CONTROLS AT A GLANCE

M. Trunk Release pg. 8

N. Hood Release pg. 85

O. Power Mirrors

P. Power Door Locks

Q. Power Windows

G. SWITCH PANEL

(behind steering wheel) pg. 18

A. Turn Signal/Lights Lever

• Heated Seat Switches pg. 16

• Electronic Stability Control pg. 70

• Hazard Switch H. Climate Controls pg. 22

I. Transmission Gear Selector

J. Power Outlet/Cigar Lighter pg. 66

K. Speed Control pg. 21

wheel) pg. 20

B. Instrument Cluster pg. 6

C. Speedometer pg. 7

D. Wiper/Washer Lever (behind steering

E. Ignition Switch (behind steering wheel)

shown) pg. 26

F. Audio System (non-touch-screen-radio

Page 8

CONTROLS AT A GLANCE

INSTRUMENT CLUSTER

Warning Lights

- Low Fuel Warning Light

- Charging System Light**

- Oil Pressure Warning Light**

- Anti-Lock Brake (ABS) Light**

- Air Bag Warning Light**

- Electronic Throttle Control (ETC) Light

- Tire Pressure Monitoring System (TPMS) Light

- Engine Temperature Warning Light

- Transmission Temperature Warning Light

- Seat Belt Reminder Light

BRAKE

(See page 70 for more information.)

- Brake Warning Light**

- Malfunction Indicator Light (MIL)**

- Electronic Stability Control (ESC) Activation/Malfunction Indicator Light**

Page 9

CONTROLS AT A GLANCE

Indicators

- Turn Signal Indicators

- High Beam Indicator

- Front Fog Light Indicator

- Park/Headlight ON Indicator

- Vehicle Security Indicator*

CRUISE

Odometer Messages

door - Door Ajar CHANgE OIL* - Change Engine Oil deck - Trunk Ajar gASCAP - Fuel Cap Fault HOTOIL* - Engine Oil is over temperature LoW tirE* - Low Tire Pressure

* If equipped ** Bulb Check with Key On

- Cruise Indicator

- Electronic Stability Control (ESC) Off Indicator

Page 10

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors

• Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door (EVIC can be setup for driver door first, otherwise this will unlock all doors), or press the unlock button twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

• All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide.

Opening The Trunk

• Press the TRUNK button on the transmitter two times within five seconds to open the trunk.

Panic Alarm

• Press the PANIC button once to turn the panic alarm on.

• Wait approximately three seconds and press the button a second time to turn the panic alarm off.

WARNING!

• When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle.

• Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicleunattended is dangerous fora number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.

• Do not leave the key fob in the vehicle, or in a location accessible to children and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.

Page 11

GETTING STARTED

REMOTE START

• Press the REMOTE START button the REMOTE START button a third time shuts the engine off.

• To drive the vehicle,pressthe UNLOCK button, insertthe key in theignition and turn tothe ON/RUN position.

• With remote start, the engine will only run for 15minutes (timeout) unlessthe ignition key is placed in the ON/RUN position.

• The vehicle must be started with the key after two consecutive timeouts.

• Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause you or others to be severely injured or killed when inhaled.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause you and others to be severely injured or killed.

THEFT ALARM

To Arm:

• Press the Key Fob LOCK button or the power door lock switch while the door is open.

To Disarm:

• Press the Key Fob UNLOCK button or turn the ignition to the ON/RUN position.

on the Key Fob twice within five seconds. Pressing

WARNING!

SEAT BELT

• Be sure everyone in your vehicle is in a seat and using a seat belt properly.

• Position the lap belt across your thighs, below your abdomen. Toremove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.

• Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.

• A shoulder belt placed behind you will not protect you from injury during a collision. You are more likelyto hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

Page 12

GETTING STARTED

• A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

• A frayed or torn beltcould rip apartin a collision and leave you with no protection. Inspect the belt system periodically, checking forcuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).

• The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision.

• A deployed pretensioner or a deployed air bag must be replaced immediately.

WARNING!

In a collision, you and your passengers can suffer much greater injuries if you are not buckled up properly.You canstrike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

• This vehicle hasAdvanced Front Air Bags for both the driver and right front passenger as a supplement to the seat belt restraint system. The Advanced Front Air Bags will not deploy in every type of collision.

• AdvancedFrontAir Bags aredesigned to provide additionalprotection by supplementing the seat belts in certain frontal collisions depending on several factors, including the severity and type of collision. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions.

• This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains to protect the driver, front and rear passengers sitting next to a window.

• This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags to provide enhanced protection to help protect an occupant during a side impact.

• If the Air Bag Warning Light driving, have the vehicle serviced by an authorized service center immediately.

• Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS).

is not on during starting, stays on, or turns on while

Page 13

GETTING STARTED

WARNING!

• Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won't deploy at all. Always wear your seat belts even though you have air bags.

• Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

• SupplementalSide Air Bag Inflatable Curtains and SupplementalSeat-Mounted Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

• Being too close to the Supplemental Side Air Bag Inflatable Curtain and/or SeatMounted Side Air Bag during deployment could cause you to be severely injured or killed.

• Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

• After any collision, the vehicle should be taken to an authorized dealer immediately.

CHILD RESTRAINTS

• Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

• Every state in the United States and all Canadian provinces require that small children ride in properrestraint systems. This is the law, and youcan be prosecutedfor ignoring it.

NOTE:

• For additional information, refer to ww w.seatcheck.org or call 1–866–SEAT-CHECK (1–866–732–8243).

• Canadian residents, should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm

Page 14

GETTING STARTED

Installing The LATCH-Compatible Child Restraint System

• Your vehicle's second row passenger seats are equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren.

• Child seats with fixed lower attachments must be installed in the outboard positions only. Child seats with flexible lower attachments can be used in all three seating positions.

• Never install LATCH-compatible child seats such that two seats share a common lower anchorage. If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use either the lower anchors or the vehicle seat belt in the outboard seating position, but the centerseating position mustuse the vehicleseat belt. Always use the top tether anchorage with a forward facing child seat.

• The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback.They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.

• In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. These tether strap anchorages are under a plastic cover.

• Loosen the child seat adjusters on the lower straps and tether straps so that you can attach the hook or connector to the lower and tether anchorages more easily.

• Attach the lower hooks or connectors over the top of the seat cover material.

• Thenrotate the tether anchoragecoverdirectly behind the seatwhereyou are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.

• Tighten all three straps as you push the child restraint rearward and downward into the seat.

Page 15

GETTING STARTED

Installing The Child Restraint Using The Vehicle Seat Belts

• To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle.

• Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

• Rotate the cover over the anchor directly behind the seat where you are placing the child restraint. These tether strap anchorages are under a plastic cover.

• Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.

• Attach the tether strap hook of the child restraint to the anchor and remove slack in the tether strap according to the child restraint manufacturer’s instructions.

WARNING!

• In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size.

• Rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger air bag. An air bag deployment could cause severe injury or death to infants in this position.

• Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be severely injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.

• An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.

Page 16

GETTING STARTED

FRONT SEATS

Power Seat

• The power seat switch, located on the outboard side of the seat near the floor, controls forward/back, up/down, and tilt adjustment.

• The recline switch controls the seatback recliner.

Manual Seat Adjustment

Forward/Rearward

• Lift up on the adjusting bar located at the front of the seatnear the floor andrelease it when the seat is at the desired position. Then, using body pressure, move forward and backward on the seat to be sure that the seat adjusters have latched.

Recliner

• Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position.

Lumbar Support

• Thelumbar adjust lever isonthe outboard side of the seatback. Rotate the lumbar adjust lever downward to increase the lumbar support orupward to decrease the lumbar support as desired.

Page 17

GETTING STARTED

Driver’s Seat Height Adjustment

• The height adjustment control lever is located on the outboard side of the seat. Raise the lever toraise the seat. Lowerthe lever to lower the seat.

CAUTION!

Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls.Seat travel may become limitedif movement is stopped by an obstruction in the seat’s path.

WARNING!

• Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could causeyouto lose control. The seatbeltmight not be properlyadjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.

• Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked.

REAR SEATS

Folding Rear Seatback

• To fold the rear seatback forward, pull on the loops to fold down either or both seatbacks. When returning the rear seatback to the upright position, be sure the seatback is latched.

Page 18

GETTING STARTED

HEATED SEATS

Front Heated Seats

• Thecontrols for the front heated seatsare located in the center console below the climate controls.

• Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

• If the High-level setting is selected, the system will automatically switch to Lowlevel after approximately 60 minutes. The Low-level setting will turn Off automatically after approximately 45 minutes.

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

Page 19

GETTING STARTED

TILT/TELESCOPING STEERING COLUMN

• The tilt/telescoping control lever is located below the steering wheel at the end of the steering column.

• Push down on the lever to unlock the steering column.

• To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.

• Pull upward on the lever to lock the column firmly in place.

WARNING!

Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle. Failure to follow this warning may result inyou and others being severely injured orkilled.

Page 20

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

• A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.

• Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.

While cruising, brief full-throttle acceleration within the limits of local traffic laws con-

• tributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.

• The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintaining Your Vehicle”.

NOTE:

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should beconsidered a normal part of the break-inand not interpreted as an indication to an engine problem or malfunction.

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.

TURN SIGNAL/LIGHTS LEVER

Page 21

OPERATING YOUR VEHICLE

Headlights/Parking Lights/Automatic Headlights

• Rotate the end of the leverto the firstdetent for parkinglights for headlights

• When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.

Instrument Panel Dimmer

• Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened.

• Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the parking lights or headlights are on.

• Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio controls when the parking lights or headlights are on.

• Rotate the center portion of the lever upward to the last detent to turn on the interior lighting.

Flash To Pass

• Pull the lever toward youto activate the high beams. The high beams will remain on until the lever is released.

High Beam Operation

• Push the lever forward to activate the high beams.

NOTE:

For safe driving, turn off the high beams when oncoming traffic is present to prevent headlight glare and as a courtesy to other motorists.

Front Fog Lights

• Turn on the parking lights or low beam headlights and pull out the end of the lever.

Turn Signals/Lane Change Assist

• Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off.

, and the third detent for AUTO.

, the second detent

Page 22

OPERATING YOUR VEHICLE

WIPER/WASHER LEVER

Front Wipers

Intermittent, Low And High Operation

• Rotatethe end ofthe lever to thefirst detent positionfor one of fiveintermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.

Mist

• Pull down on the lever and release when a single wipe is desired.

NOTE:

The mist feature does not activate the washer pump; therefore, no washerfluid will be sprayed on the windshield. The wash function must be activated in order to spray the windshield with washer fluid.

Washer Operation

• Pull the lever toward you and hold for as long as spray is desired.

Page 23

OPERATING YOUR VEHICLE

SPEED CONTROL

• The Speed Control switches are located on the steering wheel.

Cruise ON/OFF

• Push the ON/OFF button to activate the Speed Control.

will

• CRUISE cluster to indicate the Speed Control is on.

• Push the ON/OFFbutton a second time to turn the system off.

SET

•

With the Speed Control on, push and release the SET – button to set a desired speed.

Accel/Decel

• Once a speed isset, pushing the RES+ button once orthe SET – button once will increase or decrease the set speed approximately 1 mph (2 km/h).

• Push and hold the RES + button to accelerate in 5 mph (8 km/h) increments or push and hold the SET – button to decelerate in 5 mph (8 km/h) increments; release the button to save the new set speed.

appear on the instrument

Resume

To resume a previously selected set speed in memory, push the RES + button and release.

•

Cancel

• Push the CANCEL button, or apply the brakes to cancel the set speed and maintain the set speed memory.

• Push the ON/OFF button to turn the system off and erase the set speed memory.

WARNING!

• Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic Speed Control system off when you are not using it.

• Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

Page 24

OPERATING YOUR VEHICLE

MANUAL CLIMATE CONTROLS

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• Recirculation is allowed in floor and defrost/floor (mix modes) for approximately five minutes.

Heated Mirrors

• The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

AUTOMATIC TEMPERATURE CONTROLS (ATC)

Page 25

OPERATING YOUR VEHICLE

Automatic Operation

• Turn the Mode and Blower Controls to the AUTO position.

• Select the desired temperature by rotating the Temperature Control.

• The system will maintain the set temperature automatically.

Air Conditioning (A/C)

• If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C. The mode and blower will be set at the closest mode and blower position that the system was operating in AUTO.

MAX A/C

• MAX A/C sets the control for maximum cooling performance.

• Touch and release to toggle between MAX A/C and the prior settings. The soft-key illuminates when MAX A/C is ON.

• In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the MAX A/C operation to switch to the prior settings and the MAX A/C indicator will turn off.

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• If the recirculation button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically.

Heated Mirrors

• The mirrors are heated to melt frost or ice. This feature is activated whenever you turnon the rear window defroster.

Page 26

OPERATING YOUR VEHICLE

POWER SUNROOF

Manual Open/Close

• Press and hold the switch rearward to open or forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open or closed position until the switch is pressed again.

Pinch Protection Feature

• This feature will detect anobstruction in the opening of the sunroofduring Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.

NOTE:

If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled.

Page 27

OPERATING YOUR VEHICLE

WARNING!

• Never leave children unattended in a vehicle, and do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run mode). Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

• In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be severely injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

• Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

WIND BUFFETING

• Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together.

• If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.

Page 28

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM

Page 29

ELECTRONICS

Page 30

ELECTRONICS

Uconnect® 130

NOTE:

Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL” control knob to set the hours.

• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the “TUNE/ SCROLL” control knob to set the minutes.

• Press the “TUNE/SCROLL” control knob to save the time change.

• To exit, press any button/knob or wait five seconds.

Equalizer, Balance And Fade

• Pressthe “TUNE/SCROLL”controlknob and BASS, MID,TREBLE, BALANCE and FADEwill display. Rotate the “TUNE/SCROLL” control knob to select the desired setting.

Page 31

ELECTRONICS

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM or FM bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6).

• A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6).

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

Audio Jack Operation

• The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicles sound system. This requires the use of a 3.5 mm stereo audio patch cable.

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 32

ELECTRONICS

Uconnect® 130 WITH SiriusXM SATELLITE RADIO

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. Todetermine if your radio has these features, press the Voice Command button on the radio.You willhear a voice promptif you have thefeature,or see amessage on the radio stating “Uconnect Phone not available” if you do not.

• Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio featuresshould not beused when driving because they take your eyes from the road or your attention from driving.

Clock Setting

• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL” control knob to set the hours.

• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the “TUNE/ SCROLL” control knob to set the minutes.

• Press the “TUNE/SCROLL” control knob to save the time change.

• To exit, press any button/knob or wait five seconds.

Page 33

ELECTRONICS

Equalizer, Balance And Fade

• Pressthe “TUNE/SCROLL”controlknob and BASS, MID,TREBLE,BALANCE and FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired setting.

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM, FM, or SAT bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6).

• A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6).

Music Type

• Press the “MUSIC TYPE” button to activate this mode. Press the “MUSIC TYPE” button again or turn the “TUNE/SCROLL” control knob to select the desired music type (Adult Hits, Country, Jazz, Oldies, Rock, etc.).

• Once a music type is chosen and the icon is displayed, press either “SEEK” button and the radio will only search for stations with the selected music type.

NOTE:

The Music Type function only operates when in FM mode.

SETUP Button

• Pressingthe “SETUP”button allows youto select between itemsthat are available in that particular mode.

• Turn the “TUNE/SCROLL” control knob to scroll through the entries. Push the “AUDIO/ SELECT” button to select an entry and make changes.

SiriusXM Satellite Radio

• SiriusXM Satellite Radio gives you over 130 channels, including 100% commercial-free music from nearly every genre, plus allyour favorite sports, news,talk and entertainment channels–all with crystal clear, coast-to-coast coverage, all in one place and all at your fingertips.

• To access SiriusXM Satellite Radio, press the “SAT” hard-key.

Page 34

ELECTRONICS

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

LIST Button

• Press the “LIST” button tobring up a list of all folders on the CD. Scroll up or down the list by turning the “TUNE/SCROLL” control knob.

• To select a folder from the list, press the “TUNE/SCROLL” control knob and the radio will begin playing the files contained in that folder.

Audio Jack Operation

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 35

ELECTRONICS

Uconnect® 430/430N

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. Todetermine if your radio has these features, press the VoiceCommand button on the radio.You willhear a voice promptif you have thefeature,or see a message on the radio stating “Uconnect Phone not available” if you do not.

Clock Setting

• Turn the radio on, then touch the screen where the time is displayed.

• Touch the “USER CLOCK” soft-key (Navigation radio only).

• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD” soft-key.

• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE BACKWARD” soft-key.

• To save the new time setting, touch the screen where the word “Save” is displayed.

Page 36

ELECTRONICS

Equalizer, Balance And Fade

Audio Control Menu

• Press the “AUDIO” hard-key on the right side of the radio.

• Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “CENTER” soft-key resets the settings.

• Touch the “Equalizer” soft-key and use either the arrow soft-keysorthe sliders on the screen to adjust BASS, MID, and/or TREBLE.

Display Settings

• Press the “MENU” hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “EXIT” soft-key to save your settings.

Page 37

ELECTRONICS

Radio Operation

• To access Radio Mode, touch the “RADIO” hard-key on the left side of the faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen to select the band.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” soft-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.

• Find the station to store by either pressing the “Seek Up” or “Seek Down” soft-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.

• Once the station is found, touch and hold one of the “PRESET” soft-keys in the list to the right, until you hear a confirmation beep.

NOTE:

If the Presets are not visible on the right side of the screen, press the “Presets” soft-key.

Page 38

ELECTRONICS

CD/DVD Disc Operation

• Press the “MEDIA” hard key to display the media source tabs at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab.

NOTE:

Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert a CD/DVD Disc

• To insert a disc, press the “LOAD” hard-key.

• With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen.The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows “Reading...” during this process.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” soft-keys to seek through tracks in Disc Mode. Hold either Seek to bypass tracks without stopping.

Page 39

ELECTRONICS

Audio Jack Operation

• Press the “MEDIA” hard-key then the “AUX” soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. Itfunctions similar to a CD player, with the exception that the internal HDD can hold more tracks.

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

• Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs andpictures can be addedto the harddriveby using a CD or USB device (e.g. thumb drive or memory stick).

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 430/430N User's Manual for more information.

Copying Music From CD

• Press the “LOAD” hard-key.

• Insert a disc, then press the “MY FILES” hard-key and then select “MY MUSIC” soft-key.

• Touch the “Add Music Files to HDD” soft-key, then touch the “Disc” soft-key in the next screen to start the process.

NOTE:

• You mightneed to select the folder or title depending on the CD, then press “DONE” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Page 40

ELECTRONICS

Copying Music From USB

• The USB porton the radioface plate allows you to copy filesto your hard drive.To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select “MY MUSIC soft-key.”

• Touch the “Add Music Files to HDD” soft-key, then touch the “Front USB” soft-key in the next screen.

• Select the folders or titles you would like to copy,thentouch the “DONE” soft-keyto start the copy process.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in JPEG format.

• Press the “MY FILES” hard-key.

• Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “Disc” or “USB” soft-key, then select the folders or picturesyou wish to copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.

• Touch the desired pictures or press the “All” soft-key for all pictures. Confirm your selections by touching the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Display A Picture On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

• Press the “MY FILES” hard-key, then touch the “My Pictures” soft-key. Touch the desired picture, then touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly press the “MENU” hard-key and then touch the “Picture View” soft-key to display the chosen pictureon the radio screen.

NOTE:

• A check mark in the “My Pictures” screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Page 41

ELECTRONICS

Playing Music From The HDD

• Press the “MEDIA” hard-key to display the media source tabs at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touch-Screen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen.

• If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Always follow the solvent manufacturer's precautions and directions.

Garmin® Navigation

• Uconnect® 430N integrates Garmin’s consumer-friendly navigation into your vehicle. Garmin® Navigation includes a database with over 6 million points of interest.

• Touch the “NAV” soft-keyin the upper right corner of the screen to access the Navigation system.

Changing the Navigation Voice Prompt Volume

1. Program a destination.

2. While traveling on your route, touch the

upper left area of the map screen where your next turn is displayed.

3. The Navigation system will then repeat

the distance to your next turn.

4. While the Navigation systemis speaking, use the ON/OFF VOLUME rotary knob to adjust

the volume to a comfortable level. Please note the volume setting for Navigation Voice Prompt is different than the audio system.

NOTE:

For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion.

Page 42

ELECTRONICS

Main Navigation Menu

Finding Points Of Interest

• From the main Navigation menu, touch the “ Where To?” soft-key, then touch the “Points of Interest” soft-key.

• Select a Category, then a subcategory, if necessary.

• Select your destination and touch the “Go” soft-key.

Finding A Place By Spelling The Name

• Fromthe Main NavigationMenu touch the “Where To?” soft-key. Next, touch the “Points of Interest” soft-key then touch the “Spell Name” soft-key.

• Enter the name of your destination.

• Touch the “Done” soft-key.

• Select your destination and touch the “Go” soft-key.

Entering A Destination Address

From the main Navigation menu touch the “Where To?” soft-key, then touch the “Address”

• soft-key.

• Follow the on-screen prompts to enter the address then touch the “Go” soft-key.

Searching Near Another Location

• From the main Navigation menu touch the “Where To?” soft-key. Next, touch a destination then touch the “Near” soft-key.

• Select an option from the available choices.

Setting Your Home Location

From the main Navigation menu touch the “Where To?”soft-key, then touch the “Go Home”

• soft-key.

• You may enter your address directly, use your current location as your home address, or choose from recently found locations.

Edit Home Location

• From the main Navigation menu touch the “Where To?” soft-key, then touch the “Favorites” soft-key.

• Next touch the location you would like to edit, touch the “Press for More” soft-key, then the “Edit” soft-key.

Go Home

• A Home location must be saved in the system. From the Main Navigation menu, touch the “Where To?” soft-key, then touch the “Go Home” soft-key.

Page 43

ELECTRONICS

Following Your Route

•

Your route is marked with a magenta line on the map. If you depart from the original route, your route is recalculated. A speed limit icon could appear as you travel on major roadways.

Adding A Via Point

• To add a stop between the current location and the end destination (Via Point) you must be navigating a route.

• Touch the “back arrow” icon multiple times to return to the Main Navigation menu.

• Touch the “Where To?” soft-key, then search for the additional stop. Select the Via Point you wish to add from the given search results.

• Touch the “Go” soft-key, then touch the “Add to Current Route” soft-key.

Taking A Detour

• To take a detour you must be navigating a route.

• Touch the “back arrow” icon soft-key multiple times to return to the Main Navigation menu.

• Touch the “Detour” soft-key.

NOTE:

If the route you are currently taking is the only reasonable option, the device might not calculate a detour.

Page 44

ELECTRONICS

Acquiring Satellites

• The GPS Satellite strength bars indicate the strength of your satellite reception.

• Acquiringsatellite signals cantake a few minutes. When at leastone of thebars is green, your device has acquired satellite signals.

• You may experience delays receiving satellite signals when in areas with an obstructed view to the sky, such as garages, tunnels, or large cities with tall buildings.

Uconnect® 730N

NOTE:

Clock Setting

• Turn the radio on, then touch the screen where the time is displayed.

• Touch the “USER CLOCK” soft-key.

• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD” soft-key.

• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE BACKWARD” soft-key.

• To save the new time setting, touch the screen where the word “Save” is displayed.

Page 45

ELECTRONICS

Equalizer, Balance And Fade

Audio Control Menu

• Press the “MENU” hard-key on the right side of the radio. Then press the “Audio Control” soft-key to get to the audio control menu.

• Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “CENTER” soft-key resets the settings.

• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE.

Display Settings

• Press the “MENU” hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/ nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “EXIT” soft-key to save your settings.

Page 46

ELECTRONICS

Radio Operation

• To access Radio Mode, touch the “RADIO/MEDIA” hard-key on the left side of the faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch the “AM,” “FM” or “SAT” soft-key to select the band.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” hard-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.

• Find the station to store by either pressing the “Seek Up” or “Seek Down” hard-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.

• Once the station is found, touch and hold one of the PRESET soft-keys in the list to the right, until you hear a confirmation beep.

NOTE:

If the Presets are not visible on the right side of the screen, press the “Presets” soft-key.

Page 47

ELECTRONICS

CD/DVD Disc Operation

• Press the “RADIO/MEDIA” hard-key until the media source tabs are displayed at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab.

NOTE:

Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert a CD/DVD Disc

• To insert a disc, press the “OPEN/CLOSE” hard-key.

• With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen. The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows “Reading...” during this process.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” hard-keys to seek through tracks in Disc Mode. Hold either Seek to bypass tracks without stopping.

Page 48

ELECTRONICS

Audio Jack Operation

• Press the “RADIO/MEDIA” hard-key, then the “AUX” soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. The volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

• Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs andpictures can be added to the harddrive by using aCD or USB device (e.g. thumb drive or memory stick).

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 730N Supplement Manual for more information.

Copying Music From CD

• Press the “OPEN/CLOSE” hard-key.

• Insert a disc, then press the “MENU” hard-key.

• Touch the “MY FILES” soft-key, then select “MY MUSIC.”

Page 49

ELECTRONICS

• Touch the “Add Music Files to HDD” soft-key, then touch the “From Disc” soft-key in the next screen to start the process.

NOTE:

• You mightneed to select the folder or title depending on the CD, then press “Done” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Copying Music From USB

• The USB porton the radioface plate allows you to copy filesto your hard drive.To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select “MY FILES.”

• Touch the “MY MUSIC” soft-key, then touch the “Add Music Files” to HDD soft-key.

• Touch the “From USB” soft-key, then select the folders or titles you would like to copy, and then touch the “SAVE” soft-key to start the copy process.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in JPEG format.

• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files” soft-key.

• Touch the “My Pictures” soft-key toget an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “From Disc” or “From USB” soft-key, then select the folders or pictures you wish to copy tothe HDD. Use the “PAGE” soft-keys to page through the list of pictures.

Touch the desired pictures or press the

• “All” soft-key for all pictures. Confirm your selections by touchingthe “SAVE”soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Page 50

ELECTRONICS

Display A Picture On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files” soft-key and then touch the “MyPictures” soft-key. Touch the desired picture, then touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly press the “MENU” hard-key and then touch the “Picture View” soft-key to display the chosen picture on the radio screen.

NOTE:

• A check mark in the My Pictures screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Playing Music From The HDD

• Press the “RADIO/MEDIA” hard-key until the media source tabs are displayed at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touch-Screen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen.

NAVIGATION

• Your navigation system receives GPS signals from up to 16 satellites to display the position of your vehicle. Map and database information is supplied through a hard disk drive.

• Touch the “NAV” hard-key on the radio face plate to access the Navigation system and the NAV – Main Menu.

Page 51

ELECTRONICS

Changing the Navigation Guidance Prompt Volume

1. From the Navigation Map screen, touch the Menu hard-key and then touch the Guidance Prompts soft-key.

2. Select and adjust the navigation guidance prompt volume using the left and right

arrows.

3. Touch the “SAMPLE VOL” soft-key to lis-

ten to the current volume setting.

4. Once satisfied with the volume,touch the

“SAVE” soft-key to save the settings. Touch the “CANCEL” soft-key to exit the menu without saving the settings.

NOTE:

For your own safety and the safety of others, it is not possible to use the certain features while the vehicle is in motion.

Main Navigation Menu

Finding Points Of Interest

• From the NAV main menu, touch the “Points of Interest” soft-key.

• Select a Category and then a subcategory, if necessary.

• Select your destination and touch “GO.”

Page 52

ELECTRONICS

Finding A Place By Entering The Street Address

• From the NAV main menu, touch “New Destination,” then touch “Street Address.”

NOTE:

If the State and/or Country displayed are incorrect, touch the corresponding soft-key to make the correction.

• Once the Country and State are set and the Street Address screen is displayed, begin spelling the street name in the speller. In the upper right corner the number of possible roads decreases.

• Touch the “LIST” soft-key to display a list of possible street names. Select the correct street name.

• Next input the number.

• In the Confirm Route screen the navigation radio displays the complete address, a map of the destination area, and the current routing method for you to verify.

• Touch the “GO” soft-key to activate the route guidance.

Entering Your Home Location

• Press the “NAV” hard-key on the right side of the radio.

• From the Nav – Main Menu, touch “Guide Me Home” to enter your home address. If no home address has been set, touch “YES” to access the Enter Home Address menu.

• Touch “Street Address” to enter your address. Touch the soft-key with your state’s name and enter your street name into the speller.

• Once the street name has been input, touch “CONTINUE” to confirm. Enter the house number into the next screen. If more than one city has thisaddress, you will then need to select your city from a list.

• Once the address is entered completely, the system shows a map of your home address area. Touch “SAVE” to confirm the address. The system will then ask if you want to go there. Touch the “Yes” or “No” soft-key.

Change Home Address

• This procedure will allow you to change your Home Address if one has already been entered.

• Press the “MENU” hard-key, touch “My Files” and then touch “My Address Book.”

• Touch “Home,” then touch “Edit Contacts” and then “Change Address.”

• Touch the soft-key with your state’s name and enter your street name into the speller.

• Once the street name has been input, touch “CONTINUE” to confirm.

• Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list.

• Touch the “SAVE” soft-key to confirm the address.

Go Home

• From the NAV main menu, touch “Guide Me Home” when you want to route to your home destination.

Page 53

ELECTRONICS

Where Am I Now?

• From the NAV main menu, touch “Where Am I Now?” The Where Am I Now? menu displays location information for the current vehicle position.

• Touch the “NEARBY POI” soft-key to search for a local Point of Interest.

• Touch the “SAVE LOCATION” soft-key to save the current location in the Saved Locations memory.

Route Guidance

• After starting route guidance, the system calculates the route and announces: “Follow the arrows on the display.” You will receive navigation recommendations by voice messages and screen displays.

Route Options

After pressing the “OPTIONS” soft-key in the Route Guidance Menu, the following informa-

• tion is displayed:

• In the left half of the screen, the current position and the current routing method are

displayed.

• “ Take Detour” will allow you to calculate a different route.

• “Find Nearby POI” to search for a local POI.

• “Destination Info” displays destination information.

• “View Turn List” lists streets utilized for the current route.

• “Save Destination” to save the destination address.

• “Change Method” will allow you to change the routing method.

Page 54

ELECTRONICS

SiriusXM SATELLITE RADIO/TRAVEL LINK

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States.

• The following describes features that are available when in SiriusXM Satellite Radio mode.

• To access SiriusXM Satellite Radio, press the “RADIO/MEDIA” or “RADIO” andthen touch the “SAT” soft-key tab.

Info

• Touch the “i” soft-key to view detailed information about the current Sirius XM Satellite channel.

SiriusXM Parental Controls

• SiriusXM offers the option to permanently block selected channels. Call 1-888-539-7474 and request the Family Package.

• Uconnect® 430/430N and 730N: Press the “MENU” hard-key while in SiriusXM Satellite Radio Mode, then touch the “Channel Lock” to enable and/or disable desired channels. The SEEK and SCAN function will then only display channels without Channel lock.

Search/Browse

• Touch the “magnifying glass” soft-key to search/browse the SiriusXM channel listing by Favorites and Categories such as Song, Artist and Channel Name. The Search/Browse also allows you manage your Favorites.

SiriusXM Satellite Radio Favorites (SAT Favorites)

• You can save 50 favorite songs and 50 favorite artists.

• Touch the “Add Favorite” soft-key to add either the song or the artist of the currently playing program to the SAT Favorites list. The favoritestar will appear in the upper right corner, below the “SAT” softkey.

Page 55

ELECTRONICS

• You will see a favorite star indicator in the upper right side of the screen below the “SAT” soft-keyand a pop upwill alert you thata favorite song or artistis currently playing onone of the SiriusXM satellite radio channels.

NOTE:

Refer to your Uconnect® 730N or 430/430N Supplement Manual for more information.

Display SAT Favorites List

• Touch the “Search/Browse” soft-key and select “Favorites” from the SAT Browse screen.

• Touch the desired favorites soft-key to switch the SAT tuner to thecorresponding channel.

• You may use the “LIST” soft-key to toggle between:

• Favorite Songs

• Favorite Artists

• Currently playing favorites

Replay

• While you are inSATmode,you can replay 44 minutes of the current SiriusXM channel (when the channel is changed, this audio buffer is erased). Press the REPLAY button to listen to the stored audio.

• You can touch the on-screen controls to pause and rewind audio playback, touch the SCAN button to preview each of the tracks stored in the buffer, or select a track from the list.

• The time displayed below the bar indicates how much time is present between the current buffer play position and the live broadcast.

Replay Option Option Description

Play/Pause Touch to pause content playback. Touch Pause/Play again to resume

playback.

Rewind/RW Rewinds the channel content in steps of five seconds. Touch and hold to

rewind continuously, then release to begin playing content at that point.

Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However, Fast

Forward/FW can only be used when content has been previously rewound.

Page 56

ELECTRONICS

Replay Option Option Description

Replay Time Displays the amount of time intheupper center of the screen by whichyour

Live Resumes playback of live content at any time while replaying rewound

SiriusXM Travel Link (Uconnect® 730N & Uconnect® 430N Only)

NOTE:

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States.

• SiriusXM Travel Link brings a wealth of useful information into your vehicle and right to your fingertips.

• To access Travel Link, press the MENU hard-key, then the Travel Link soft-key.

content lags the live channel.

content.

1 – Favorites

2 – Forecast

3 – Ski Info 4 – Fuel Prices 5 – Movies 6 – Sports

View and store your favorite location, theater and sport teams for quick access.

View detailed weather conditions, forecasts and ski/snowboarding conditions at resorts.

View ski and snowboarding conditions at ski resorts. View detailed price information for fuel stations. View information on movies that are playing at theaters. View sports scores and upcoming events for all major sports.

Page 57

ELECTRONICS

STEERING WHEEL AUDIO CONTROLS

• The steering wheel audio controls are located on the rear surface of the steering wheel.

Right Switch

• Pressthe switch upor down toincrease or decrease the volume.

• Press the button in the center to change modes AM/FM/CD/SAT.

Left Switch

• Press the switch up or down to search for the next listenable station or select the next or previous CD track.

• Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer.

iPod®/USB/MP3 CONTROL

• There are many waysto play music from iPod®/MP3 players or USBdevices through your vehicle's sound system.

• The remote USB port, located within the front storage area, allows you to plug an iPod® into the vehicle's sound system.

NOTE:

If equipped with the Uconnect® 730N, the USB port on the faceplate allows the same functions as the remote USB port.

Page 58

ELECTRONICS

• Non-Touch-Screen Radios: To hearaudio from devicesconnected to the USB port, press the “AUX” button on the radio faceplate.

• Touch-Screen Radios: To hear audio from devices connected to the USB port, press the “MEDIA” hard-key, then touch the “AUX” or “iPod®” soft-key.

• When connected to this feature:

• The iPod® can be controlled using the radio buttons to Play, Browse, and List the iPod® or external devices contents.

• The iPod® battery charges when plugged into the USB port (if supported by the specific audio device).

• Compatible iPod® devices may also be controllable using voice commands. Refer to the Owner's Manual on the DVD for details.

NOTE:

The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For supported audio file formats, refer to the USB Port section in the Owner's Manual on the DVD. Refer to www.UconnectPhone.com website for a list of tested iPod®s. Some iPod® software versions may not fully support the USB port features. Please visit Apple’s website for iPod® software updates.

WARNING!

Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision.

Uconnect® Phone

• To determine if your vehicle is equipped with Uconnect® Phone, press the “Uconnect® Phone” button will hear a voice prompt. If not, you will see a message on the radio “Uconnect phone not available.”

• The Uconnect® Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section).

NOTE:

To access the tutorial, press the “Uconnect® Phone” button “tutorial.” Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the “tutorial.”

located on the radio faceplate. If your vehicle has this feature, you

. After the BEEP, say

Page 59

ELECTRONICS

• The Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands.

• Refer to your vehicle Owner's Manual on the DVD for further details.

NOTE:

The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® Hands-Free Profile, Version 1.0 or higher. For Uconnect® Customer Support: U.S. residents - visit www.UconnectPhone.com or call 1–877–855–8400. Canadian residents - visit www.UconnectPhone.com or call, 1-800-465–2001 (English) or 1-800-387-9983 (French). This site will provide specific instructions based on the type of mobile phone being paired.

Phone Pairing

NOTE:

Pairing is a one - time initial setup before using the phone. Prior to starting the pairing procedure ensure all additional phones within the vehicle have their Bluetooth® disabled.

• Press the “Phone”

• Wait for the “ready” prompt and BEEP.

• After the BEEP, say ”setup” or “Uconnect device setup.”

• After the BEEP, say “device pairing.”

• After the BEEP, say “pair a device.”

• Follow the audible prompts.

• You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can say any four-digit PIN. You will not need to remember this PIN after the initial pairing process.

• You will then be prompted to give the phone pairing a name (each phone paired should have a unique name).

• Next you will be asked to givethis new pairing a priority of1 through 7 (upto seven phones may be paired); 1 is the highest and 7 is the lowest priority. The system will only connect to the highest priority phone that exists within the proximity of the vehicle.

You will then need to start the pairing procedure on your cell phone. Follow the Bluetooth®

• instructions in your cell phone Owner's Manual to complete the phone pairing setup.

button to begin.

Page 60

ELECTRONICS

Phonebook

Phonebook Download – Automatic Phonebook Transfer From Mobile Phone

• If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. Automatic Transfer is indicated by a green arrow at the bottom of the screen. See www.UconnectPhone.com for supported phones.

• Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone. For example, after you start the vehicle.

NOTE:

The mobile phone may require authorization prior to download.

• Amaximum of 1000 entriesper phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone.

• Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previously downloaded phonebook is available for use.

• Only the phonebook of the currently connected mobile phone is accessible.

• Only the mobile phone’s phonebook is downloaded. The SIM card phonebook is not part of the Mobile phonebook.

• This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect® Phone on the next phone connection.

Making A Phone Call

• Press the “Phone” button

• After the BEEP, say “dial” (or “call” a name).

• After the BEEP, say number (or name).

Receiving A Call – Accept (And End)

• When an incomingcall rings/is announced on Uconnect®, press the Phone button

• To end a call, press the Phone button

Mute (Or Unmute) Microphone During Call

• During a call, press the “Voice Command” button

• After the BEEP, say “mute” (or “mute off”).

Page 61

ELECTRONICS

Transfer Ongoing Call Between Handset And Vehicle

• During a call, press the “Voice Command” button

• After the BEEP, say “transfer call.”

Changing The Volume

• Start a dialogue by pressing the “Phone” button normal call.

• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Uconnect® system is speaking. Please note the volume setting for Uconnect® is different than the audio system.

WARNING!

• Any voice commandedsystem should be used only in safe driving conditions following applicable laws regarding phone use. Yourattention should be focused on safely operating the vehicle. Failuretodo so may resultin a collision causingyou and others to be severely injured or killed.

• In an emergency, to use Uconnect® Phone, your mobile phone must be:

• turned on,

• paired to Uconnect® Phone,

• and have network coverage.

Uconnect® VOICE COMMAND

, then adjust the volume during a

Voice Command Operation

• The Uconnect® Voice Command systemallows you to controlyour AM, FMradio, satellite radio, disc player, HDD, Uconnect® Phone, a memo recorder, and supported portable media devices.

• When you press the “Voice Command” button steering wheel, you will heara beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the “Voice Command” button

NOTE:

Visit http://www.driveuconnect.com/features/voiceCommand/ for more info on which voice command features apply to your vehicle.

, listen for the BEEP, and say your command.

located on the radio faceplate or

Page 62

ELECTRONICS

• Start a dialogue by pressing the “VoiceCommand” button , you will hear a beep. The beep is your signal to give a command. Below are a list of voice commands for each of the different modes.

Common Voice Commands (Examples)

While In: Voice Command Example:

“Radio AM” (to switch to the AM radio mode)

“Radio FM” (to switch to the FM radio mode)

“Satellite Radio” (to switch to the Satellite radio mode)

Main Menu

Radio Mode

SiriusXM Satellite

Radio Mode

Disc Mode

“Bluetooth Streaming” (to switch to the Bluetooth Streaming mode)

“Channel Number” (to change the channel by its spoken number)

"Channel Name" (to change the channel by its spoken name)

“Disc” (to switch to the disc mode) “USB” (to switch to the USB mode)

“Memo” (to switch to the memo recorder)

“System Setup” (to switch to system setup)

“Frequency” (to change the frequency)

“Next Station” (to select the next station)

“Previous Station” (to select the previous station)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

“Next Channel” (to select the next channel)

“Previous Channel” (to select the previous channel)

“List Channel” (to hear a list of available channels)

“Select Name” (to say the name of a channel)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

“Track” (#) (to change the track)

“Next Track” (to play the next track)

“Previous Track” (to play the previous track)

“Main Menu” (to switch to the main menu)

Page 63

ELECTRONICS

While In: Voice Command Example:

To switch to the voice recorder mode, say “Memo.” The following

are common voice commands for this mode: “New Memo” (to

record a new memo) — During the recording, you may press the

Voice Command button

Memo Mode

Voice Text Reply

• If equipped with Uconnect® Voice Command, your Uconnect® 430N, 730N & 731N radios may be able to play incoming Short Message Service (SMS) messages (text messages) through the vehicle's sound system.

• It also allows you to respond by selecting from various pre - defined phrases.

• Not all phones are compatible with this feature. Refer to the phone compatibility list at www.UconnectPhone.com. Connected mobile phones must be bluetooth-compatible and paired with your radio.

• Pressthe “Voice Command” button

NOTE:

To access the tutorial, press the “Voice Command” button “tutorial.” Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial.

— “Play Memos” (to play previously recorded memos) — During

the playback you may press the Voice Command button

to stop playing memos. You proceed by saying one of the follow-

by saying one of the following commands:

— “Save” (to save the memo)

— “Continue” (to continue recording)

— “Delete” (to delete the recording)

— “Repeat” (to repeat a memo)

— “Next” (to play the next memo)

— “Previous” (to play the previous memo)

— “Delete” (to delete a memo)

— “Delete All” (to delete all memos)

and after the BEEP,say “SMS” to get started.

to stop recording. You proceed

ing commands:

. After the BEEP, say

WARNING!

Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed.

Page 64

ELECTRONICS

Bluetooth® STREAMING AUDIO

• If equipped with Uconnect® Voice Command, your Bluetooth-equipped iPod® devices, cell phones or other media players, may also be able to stream music to your vehicles speakers. Your connected device must be Bluetooth-compatible, and paired with your radio (see Uconnect® Phone for pairing instructions).

• Non-Touch-Screen Radios: Press the “AUX” button on the radio faceplate until "BT" or “Audio Streaming” is displayed on the radio screen.

• Touch-Screen-Radios: Press the “RADIO/MEDIA” or “MEDIA” hard-key and then touch the “AUX” soft-key tab.

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)

• The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the left side of the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to “Programmable Features” located in this guide.

• Press and release the MENU button to advance the display to Trip Functions or Personal settings or to return to the default System status display.

• Press and release the DOWN Functions or Personal Settings.

• Press and release the COMPASS outside temperature.

• Press and release the SELECT resets various Trip Functions.

Compass Calibration

• This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.

• You may also calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message displayed in the EVIC turns off. The compass will now function normally.

button to advance the display through the various Trip

button to display the compass heading and the

button to accept a selection. The SELECT Button also

Page 65

ELECTRONICS

PROGRAMMABLE FEATURES

Electronic Vehicle Information Center (EVIC)

• The EVIC can be used to program the following Personal Settings. Press and release the MENU button until Personal Settings displays, then press the DOWN button through the settings. Press the SELECT button

• Language • Headlights With Wipers

• Auto Unlock On Exit

• RKE Unlock

• Sound Horn With Lock

• Flash Lamps With Lock

• Headlamp Off Delay

Key Fob Programmable Features

• The following features may also be programmed by using the Key Fob transmitter or the ignition switch and driver's door lock switch.

NOTE:

Pressing the LOCK button while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.

Unlock On First Press

• To unlock either the driver's side, or all doors, on the first press of the UNLOCK button:

Press and hold the LOCK button for at least four seconds, but no longer than 10 seconds.

• Then, press and hold the UNLOCK button while still holding the LOCK button.

• Release both buttons at the same time.

Auto Unlock Doors On Exit

• To have all of the vehicle doors unlock when any door is opened:

• Enter your vehicle and close all the doors, and fasten your seat belt.

• Cycle the ignition switch between the LOCK and ON position four times, ending in the LOCK position (do not start the engine).

• Press the power door UNLOCK switch to unlock the doors. A single chime will indicate that programming is complete.

Sound Horn With Lock

• To turn the horn chirp on or off when the doors are locked:

• Press the LOCK button for at least four seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button.

• Release both buttons at the same time.

Flashing Lights With Lock

• The turn signal lights flashing, when the doors are locked or unlocked, feature can be turned on or off. To turn this feature on or off:

•

Press and hold the UNLOCK button for at least four seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button.

• Release both buttons at the same time.

to change the setting.

(Available with Auto Headlights Only)

• Key Off Power Delay

• Illumin. Approach

• Display Units In

• Calibrate Compass

• Compass Variance

to scroll

Page 66

ELECTRONICS

UNIVERSAL GARAGE DOOR OPENER (HomeLink®)

•

HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery.

• The HomeLink® buttons that are located in the overhead console or sunvisor designate the three different HomeLink® channels.

• The HomeLink® indicator is located above the center button.

Before You Begin Programming HomeLink®

Ensure that your vehicle is parked outside

• of the garage before you begin programming.

• For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.

Erase all channels before you begin pro-

• gramming. To erase the channels, place the ignition switch into the ON/RUN position, then press and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds or until the red indicator flashes.

NOTE:

Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons.

• If you have any problems,or require assistance, please call toll-free 1–800–355–3515or, on the Internet at www.HomeLink.com for information or assistance.

Programming A Rolling Code

• For programming Garage Door Openers that were manufactured after 1995. These Garage Door Openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the Garage Door Opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer.

• Place the ignition switch into the ON/RUN position.

• Place the hand-held transmitter 1 to 3in (3 to8 cm) away fromthe HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

Page 67

ELECTRONICS

• Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

• Continue to hold both buttons and observe the indicator light. The HomeLink® indicator will flash slowly and then rapidly afterHomeLink® has received thefrequencysignal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.

• At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly press and release the “LEARN” or “TRAINING” button.

NOTE:

You have 30 seconds in which to initiate the next step after the LEARN button has been pressed.

• Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.

NOTE:

If the device does not activate, press the button a third time (for two seconds) to complete the training.

• To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.

Programming A Non-Rolling Code

• For programming Garage Door Openers manufactured before 1995.

• Turn the ignition switch to the ON/RUN position.

• Place the hand-held transmitter1 to 3in (3 to 8 cm) away fromthe HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

• Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

• Press and hold the programmed HomeLink® button and observe the indicator light.

NOTE:

• If the indicator light stays on constantly, programming is complete and the garage

door (or device) should activate when the HomeLink® button is pressed.

• To program the two remaining HomeLink® buttons, repeat each step for each remain-

ing button. DO NOT erase the channels.

Page 68

ELECTRONICS

Using HomeLink®

• To operate, press and release the programmed HomeLink® button. Activation will now occur for the programmed device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time.

WARNING!

• Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people or pets are in the path of the door or gate.

• Do not run your vehicle in a closed garage or confined area while programming the transceiver. Exhaust gas from your vehicle contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous when inhaled and can cause you and others to be severely injured or killed.

POWER OUTLET

• There are two 12 Volt electrical outlets on this vehicle.

• The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This power outlet will also operate a conventional cigar lighter unit.

• There is also a power outlet located on the inside of the center console. This power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.

Page 69

ELECTRONICS

NOTE:

• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced.

• Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle warranty.

Page 70

UTILITY

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)

The following chart provides the maximum trailer weight ratings towable for your given drivetrain.

Maximum Trailer Weight Ratings

Engine/

Transmission

2.4L/Auto

3.6L/Auto 22 sq. ft. (2.0 sq. m) 1,000 lbs (450 kg) 100 lbs (45 kg)

The trailer tongue weightmust be considered aspart of the combinedweight of occupants and cargo, and it should never exceed the weight referenced on the Tire and Loading Information placard.

Enclosed trailers or openutility trailers with frontshields/guards are not recommendedfor use with four-cylinder engines with an automatictransmission. Please see your authorized dealer for additional information.

Max. Frontal Area

11 sq ft (1.0 sq.m)

(See Note

Refer to local laws for maximum trailer towing speeds.

)

CAUTION!

Towing a trailer with a larger than recommended frontal area could cause the engine to

overheat or cause severe engine damage under extreme conditions.

Max. GTW

(Gross Trailer Wt.)

1,000 lbs (450 kg) 100 lbs (45 kg)

Max. Trailer

Tongue Wt.

Page 71

UTILITY

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)

Towing This Vehicle Behind Another Vehicle

Towing Condition Wheels OFF the Ground All Models

Flat Tow NONE

Dolly Tow

On Trailer ALL OK

Recreational Towing – All Models

• Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure:

• Properly secure the dolly to the tow vehicle, following the dolly manufacturer's instructions.

• Drive the front wheels onto the tow dolly.

• Firmly apply the parking brake. Place the transmission in PARK.

• Properly secure the front wheels to the dolly, following the dolly manufacturer's instructions.

• Release the parking brake.

Front OK Rear

CAUTION!

NOT ALLOWED

• DO NOT flat tow this vehicle. Damage to the drivetrain will result. Towing this vehicle in violation of the above requirements can cause severe transmis-

• sion damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.

Page 72

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE

•

Dial toll-free 1-800-521-2779 for U.S. Residentsor 1-800-363-4869 forCanadian Residents.

•

Provide your name, vehicle identification number, license plate number, and your location, including the telephone number from which you are calling.

• Briefly describe the nature of the problem and answer a few simple questions.

You willbe given the name of the service provider and an estimated time ofarrival. If you feel

• you are in an “unsafe situation”, please let us know. With your consent, we will contact local police or safety authorities.

INSTRUMENT CLUSTER WARNING LIGHTS

- Electronic Stability Control (ESC) Activation/Malfunction Indicator Light

• If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph(48 km/h), werecommendyou do not operate the vehicle. Have the vehicle serviced immediately.

• The “ESC Activation/Malfunction Indicator Light” starts to flashas soon as the tires lose traction and the ESC system becomes active. If the light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. The light also flashes when TCS is active.To improve the vehicle's tractionwhen starting offin deep snow, sand or gravel, it may be desirable to switch the ESC system to Partial Off mode by momentarily pressing the ESC Off

switch.

- Tire Pressure Monitoring System (TPMS) Light

• Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

• As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stopand check your tiresas soon as possible,and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

• IF THE LIGHT STARTS FLASHING INDICATING A LOW TIRE PRESSURE, ADJUST THE

AIR PRESSURE IN THE LOW TIRE TO THE AIR PRESSURE SHOWN ON THE VEHICLE PLACARD OR TIRE INFLATION PRESSURE LABEL LOCATED ON THE DRIVER'S DOOR.

Page 73

WHAT TO DO IN EMERGENCIES

NOTE:

AFTER INFLATION,THE VEHICLE MAY NEED TO BE DRIVEN FOR 20 MINUTES BEFORE THE FLASHING LIGHT WILL TURN OFF.

• Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Your vehiclehas also been equipped with a TPMSmalfunction indicator toindicate when the

• system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue each time the vehicle is restarted as long as the malfunction exists.

•

When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur fora variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one ormore tires or wheelson your vehicle, toensure that the replacementor alternate tires and wheels allow the TPMS to continue to function properly.

NOTE:

Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature is 68°F (20°C) and the outside temperature is 32°F (0°C), then the coldtire inflation pressure should beincreased by 3 psi(21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is notof the samesize, type, and/or style. Aftermarketwheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

- Engine Temperature Warning Light

• This light warns of an overheated engine condition.

• If the light turns on or flashes continuously while driving, safely pull over and stop the vehicle. If theA/C system is on,turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately.

• Werecommend thatyou do not operate thevehicle or engine damagewill occur.Have the vehicle serviced immediately.

Page 74

WHAT TO DO IN EMERGENCIES

WARNING!

A hot engine cooling system is dangerous. Youor others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats.

BRAKE

• The Brake Warning light illuminates when there is either a system malfunction or the

• Please have your vehicle serviced immediately.

- Brake Warning Light

parking brake is applied. Ifthe light is on and the parking brake is not applied, it indicates a possible brake hydraulic malfunction, brake booster problem or an Anti-Lock Brake System problem.

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.

- Malfunction Indicator Light (MIL)

• Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles. In most situations, the vehicle will drive normally and not require towing.

• If the MIL flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage. We recommend you do not operate the vehicle. Have the vehicle serviced immediately.

- Charging System Light

• This light shows the status of the electrical chargingsystem. If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.

• We recommend you do not continue driving if the charging system light is on. Have the vehicle serviced immediately.

- Oil Pressure Warning Light

• This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on.

• We recommend you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately.

Page 75

WHAT TO DO IN EMERGENCIES

- Anti-Lock Brake (ABS) Light

• This light monitors the Anti-Lock Brake System (ABS).

• Ifthe light is noton during starting, stayson, or turns on whiledriving, we recommend you drive to the nearest authorized dealer immediately and have the vehicle serviced immediately.

- Electronic Throttle Control (ETC) Indicator Light

• This light informs you of a problem with the system.

• If a problem is detected, the light will come on while the engine is running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the PARK position; the light should turn off.

• If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer immediately. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing.

— Transmission Temperature Warning Light

• This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle, with the transmission in NEUTRAL, until the light turns off. Once the light turns off, you may continue to drive normally.

- Air Bag Warning Light

• If the light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized dealer immediately.

Fuel Cap/Loose Gas Cap Message

• If a “gas cap”message (shown asgASCAP) appears, tightenthe gas cap until a “clicking” sound is heard.

• Press the odometer reset button to turn the message off.

• If the message continues to appear for more than three days after tightening the gas cap, see your authorized service center.

Oil Change Indicator

Message

• If an “oil change” message (shown as CHANgE OIL) appears and a single chime sounds, it is time for your next required oil change.

Resetting The Light After Servicing

• Turn the ignition switch to the ON/RUN position (do not start engine).

• Fully depress the accelerator pedal three times within 10 seconds.

• Turn the ignition switch to the OFF/LOCK position.

Page 76

WHAT TO DO IN EMERGENCIES

IF YOUR ENGINE OVERHEATS

• In any of the following situations, you can reduce the potential for overheating by taking the appropriate action.

• On the highways — slow down.

• In city traffic — while stopped, shift transmission into NEUTRAL, but do not increase engine idle speed.

NOTE:

There are steps that you can take to slow down an impending overheat condition:

• If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.

• You can also turn the Temperature Control to maximum heat, the Mode Control to floor and the Fan Control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.

• If the temperature reading does not return to normal, turn the engine off immediately.

• Werecommend thatyou do not operate thevehicle or engine damagewill occur.Have the vehicle serviced immediately.

Engine Oil Overheating — 2.4L Gas

• On hot days the engine oil temperature may become too hot during sustained highspeed driving or if towing a trailerup long grades. If this happens, a HOTOIL message will flash in the odometer and the vehicle speed will be reduced to 48 mph (77 km/h) maximum until the engine oil temperature is reduced.

NOTE:

Although the maximum vehicle speed is reduced to 48 mph (77 km/h), you may reduce vehicle speed further as needed. Once the engine oil temperature is reduced, you may continue to drive normally.

CAUTION!

Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately, and call for service.

WARNING!

You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If yousee or hear steamcoming from under the hood,do not open thehood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.

Page 77

WHAT TO DO IN EMERGENCIES

JACKING AND TIRE CHANGING

Jack Location

• The jack and jack-handle are stowed under the load floor in the trunk.

Spare Tire Stowage

• The compact spare tire is stowed under the rear load floor in the trunk.

Spare Tire Removal

• Lift up the load floor cover and remove the hold down.

Preparations For Jacking

1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.

2. Turn on the Hazard Warning flashers.

3. Set the parking brake.

Place the shift lever into PARK (automatic transmission) or REVERSE (manual transmission).

5. Turn OFF the ignition.

6. Block both the front and rear of the wheel diagonally opposite the jacking position.

For example, if changing the right front tire, block the left rear wheel.

NOTE:

Passengers should not remain in the vehicle while the vehicle is being jacked.

Page 78

WHAT TO DO IN EMERGENCIES

Jacking Instructions

1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.

NOTE:

The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place.

2. Loosen, but do not remove, the wheel

nuts by turning them to the left one turn while the wheel is still on the ground.

3. There is a front and rear jacking location

on each side of the vehicle.

Page 79

WHAT TO DO IN EMERGENCIES

4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engagedwith the lift area closest to the wheel to be changed. Do not raise the vehicle until youare sure the jack is securely engaged.

5. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability.

6. Remove the wheel nuts, and pull the wheel and wheel covers (where applicable) off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts.

7. Lower the vehicle by turning the jack

screw to the left.

8. Finish tightening the nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct wheel nut torque is 100 ft lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your authorized dealer or at a service station.

9. Remove the wheel blocks and lower the jack until it is free. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the means provided.

10. Place the deflated (flat) tire in the cargo area and have the tire repaired or replaced as

soon as possible.

11. Check the tire pressure as soon as possible. Correct the tire pressure as required.

Page 80

WHAT TO DO IN EMERGENCIES

Road Tire Installation

Vehicles Equipped With Wheel Covers

1. Mount the road tire on the axle.

2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valvestem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.

Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover.

4. Install the remaining lug nuts with the

cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.

5. Lower the vehicle to the ground by turn-

ing the jack handle counterclockwise.

6. Finish tightening the lug nuts. Push down

on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tightness of each lug nut is 100 ft/lbs (135 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station.

7. After 25 miles (40 km) check the lug nut torque with a torque wrenchto ensure thatall lug

nuts are properly seated against the wheel.

Vehicles Without Wheel Covers

1. Mount the road tire on the axle.

2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel.

Lightly tighten the lug nuts.

3. Lower the vehicle to the ground by turning the jack handle counterclockwise.

4. Finish tightening thelug nuts. Push downon the wrench while atthe end of thehandle for

increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tightness of each lug nut is 100 ft/lbs (135 N·m). If in doubt about the correcttightness, have themchecked with a torque wrench by your authorized dealer or service station.

5. After 25miles (40 km) checkthe lug nut torque witha torque wrench to ensurethat all lug

nuts are properly seated against the wheel.

1 — Valve Stem 4 — Wheel Cover 2 — Valve Notch 5 — Mounting Stud 3 — Wheel Lug Nut

Page 81

WHAT TO DO IN EMERGENCIES

CAUTION!

Do not attemptto raise thevehicle by jacking on locations other than those indicated

• in the Jacking Instructions for this vehicle.

• Be sure to mount the sparetire with the valve stem facing outward. The vehiclecould be damaged if the spare tire is mounted incorrectly.

WARNING!

• Being under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.

• Never start or run the engine while the vehicle is on a jack.

• The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle forservice purposes. The vehicle should be jackedon a firm level surface only. Avoid ice or slippery areas.

• Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.

•

Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle:

• Always park on a firm, level surface as far from the edge of the roadway as pos-

sible before raising the vehicle.

• Turn on the Hazard Warning flasher.

• Block the wheel diagonally opposite the wheel to be raised.

• Set the parking brake firmly and set an automatic transmission in PARK; a

manual transmission in REVERSE.

• Do not let anyone sit in the vehicle when it is on a jack.

• Do not get under the vehicle when it is on a jack. Only use the jackin the positions indicatedand for lifting this vehicleduring a tire change.

•

• If working on or near a roadway, be extremely careful of motor traffic. To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed

• with the valve stem facing the ground.

•

Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.

• To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges.

•

A loose tire or jack thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately.

• To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. Failure to follow this warning may result in personal injury.

Page 82

WHAT TO DO IN EMERGENCIES

BATTERY LOCATION

• The battery in your vehicle is located between the left front headlight assembly and the left front wheel splash shield. To allow jump-starting there are remote battery posts located on the left side of the engine compartment.

JUMP-STARTING

• If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack follow the manufacturer's operating instructions and precautions.

Preparations For Jump-Start

• The battery in your vehicle is located between the leftfront headlight assembly and the left front wheel splash shield. To allow jump-starting there are remote battery posts located on the left side of the engine compartment.

1. Set the parking brake, shift the automatic transmission into PARK and turn the ignition to LOCK.

2. Turn off the heater, radio, and all unnec-

essary electrical accessories.

3. Remove the protective cover over the re-

mote positive (+) battery post. To remove the cover, press the locking tab and pull upward on the cover.

Page 83

WHAT TO DO IN EMERGENCIES

4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF.

Jump-Starting Procedure

1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the

discharged vehicle.

2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery.

3. Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery.

4. Connect the opposite end ofthe negative (-) jumper cable to the remote negative (-) post of the vehicle with the discharged battery.

5. Star t the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then star t the engine in the vehicle with the discharged battery. Once the engine is started, remove the jumper cables in the reverse sequence:

6. Disconnect the negative (-) jumper cable fromthe remote negative(-) post ofthe vehicle with the discharged battery.

7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the

booster battery.

8. Disconnect the opposite end of the positive (+) jumper cable fromthe positive (+) post of the booster battery.

9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle.

10. Reinstall the protectivecoverover the remote positive (+)battery post ofthe discharged

vehicle.

NOTE:

If frequent jump-starting is required to start your vehicle you should have the battery and charging system inspected at your authorized dealer.

CAUTION!

• Do not use a portable battery booster packor any otherbooster source witha system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.

• Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.

• Accessories that can be plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.

Page 84

WHAT TO DO IN EMERGENCIES

WARNING!

• When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above the freezing point before attempting a jump-start.

• Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.

• Remove any metal jewelry, such as watch bands or bracelets, that might make an inadvertent electrical contact. You could be severely injured.

• Batteries contain sulfuric acidthat can burnyour skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery.

• Donot allow vehicles totouch each other asthis could establish aground connection and personal injury could result.

• Failure to follow this procedure could result in personal injury or property damage due to battery explosion.

• Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury.

SHIFT LEVER OVERRIDE

• If a malfunction occursand the shift levercannot be moved outof the PARK position, you can use the following procedure to temporarily move the shift lever:

• To access the shift lever override, remove the cupholder liner.

• Firmly set the parking brake.

• Turn the ignition switch to the ACC or ON position without starting the engine.

• Press and maintain firm pressure on the brake pedal.

• Using a screwdriver or similar tool, press and hold the override tab through the access port on the center console.

• Move the shift lever into the NEUTRAL position.

• The vehicle may then be started in NEUTRAL.

• Reinstall the override cover.

Page 85

WHAT TO DO IN EMERGENCIES

TOWING A DISABLED VEHICLE

Model Flat Towing

FWD Without aKey

FWDWithaKey

(all four wheels on the ground)

NOT Permitted Recommended

Shift lever must be in NEUTRAL. The distance to be traveled must not exceed 15 mi (25 km), and the towing speed must not exceed 25 mph (40 km/h).

Flatbed Towing (all four wheels suspended OFF the ground)

Method

Recommended Method

Front Wheels Raised, Rear Wheels on the Ground

May Be Used NOT Permitted

Rear Wheels Raised, Front Wheels on the Ground

without a front end dolly

FREEING A STUCK VEHICLE

•

If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.

NOTE:

To improve the vehicle's traction when starting off in deep snow, sand or gravel, it may be desirable to switch the Electronic Stability Control (ESC) to “Partial Off” mode by momentarily pressing the ESC Off Manual on the DVD.

switch. For further information on ESC, refer to the Owner's

CAUTION!

• When “rocking” a stuck vehicle by moving between REVERSE and DRIVE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.

• Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).

WARNING!

Fast spinning tires can bedangerous. Forces generated by excessivewheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle's wheels faster than 30 mph (48 km/h) when you are stuck. Do not let anyone near a spinning wheel, no matter what the speed.

Page 86

WHAT TO DO IN EMERGENCIES

EVENT DATA RECORDER (EDR)

• This vehicle is equipped with an Event Data Recorder (EDR).The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR inthis vehicle is designed to record such data as:

• How various systems in your vehicle were operating.

• Whether or not the driver and passenger safety belts were buckled/fastened.

• How far (if at all) the driver was depressing the accelerator and/or brake pedal.

• How fast the vehicle was traveling.

• These data can help provide a better understanding of the circumstances in which crashes and injuries occur.

NOTE:

EDR data are recorded byyourvehicle only if anon-trivialcrash situation occurs; nodata are recorded by the EDR under normal driving conditions and no personal data (e.g. name, gender, age, and crash location) are recorded. However,other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.

• To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.

Page 87

MAINTAINING YOUR VEHICLE

OPENING THE HOOD

•

Pull the release lever located below the instrument panel and in front of the driver’s door.

• Raise the hood and locate the safety latch, in the middle of the hood opening.

• Move the safety latch while lifting the hood at the same time.

• Insert the support rod into the slot on the hood.

• To close thehood, remove the supportrod and place it in the retaining clip, then lower the hood slowly.

WARNING!

Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.

Page 88

MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT

2.4L Engine

Page 89

MAINTAINING YOUR VEHICLE

3.6L Engine

Page 90

MAINTAINING YOUR VEHICLE

FLUIDS AND CAPACITIES

Component Fluid, Lubricant, or Genuine

Engine Coolant–

2.4L Engine

Engine Coolant–

3.6L Engine

Engine Oil with Filter–

2.4L Engine

Engine Oil with Filter–

3.6L Engine

Fuel Selection – All Engines (Except 2.4L PZEV)

Fuel Selection–

2.4L PZEV Engine Engine Oil Filter We recommend you use

Spark Plugs 2.4L– Except PZEV Engine

Spark Plugs 2.4L– With PZEV Engine

Spark Plugs– 3.6L Engine

Part

We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology).

We recommend you use API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to the engine oil filler cap for correct SAE grade.

We recommend you use API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade.

87 Octane 16.9 Gallons (64 Liters)

87 Octane 18.5 Gallons (70 Liters)

MOPAR® brand Engine Oil Filters.

We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.1 mm]).

We recommend you use MOPAR® Spark Plugs (Gap 0.031 in [0.8 mm]).

We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.1 mm]).

Capacities

7.7 Quarts (7.3 Liters) Includes heater and coolant recovery bottle filled to MAX level.

11.6 Quarts (11 Liters) Includes heater and coolant recovery bottle filled to MAX level.

4.5 Quarts (4.4 Liters)

6 Quarts (5.6 Liters)

(Approximate)

—

Page 91

MAINTAINING YOUR VEHICLE

Component Fluid, Lubricant, or Genuine

Automatic Transmission

Brake Master Cylinder

Power Steering Reservoir

Part

We recommend you ONLY use MOPAR® ATF+4® Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or performance of your transmission.

We recommend you use MOPAR® DOT 3 and SAE J1703. If DOT 3 is not available, then DOT 4 is acceptable.

We recommend you use MOPAR® Power Steering Fluid+4orMOPAR®ATF+4® Automatic Transmission Fluid.

Capacities

—

CAUTION!

•

Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze). If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS-12106), by an authorized dealer as soon as possible.

• Do not use wateralone or alcohol-basedengine coolant (antifreeze)products.Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator.

• This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-basedengine coolant (antifreeze)is not recommended.

E85 FLEXIBLE FUEL — 3.6L ENGINE ONLY

Refer to your Owner's Manual on the DVD for further details.

CAUTION!

Only vehicles with the E-85 fuel filler door label or a yellow gas cap can operate on E-85.

Page 92

MAINTAINING YOUR VEHICLE

MAINTENANCE SCHEDULE

Your vehicleis equipped with anautomatic oil change indicator system. The oil changeindicator system will remind you that it is time to take your vehicle in for scheduled maintenance.

Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle. Operating conditions such as frequent shorttrips, trailer tow, extremely hotor cold ambienttemperatures, and E85 fuelusage will influence when the “Oil Change Required” messageis displayed. SevereOperating Conditions cancause the change oil message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).

Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Information Center(EVIC)/Oil Change Required” in “Understanding Your Instrument Panel” for further information.

NOTE:

Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first.

Once A Month Or Before A Long Trip:

• Check engine oil level

• Check windshield washer fluid level

• Check the tire inflation pressures and look for unusual wear or damage

• Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and transmission as needed

• Check function of all interior and exterior lights

Required Maintenance Intervals.

Refer to the maintenance schedules on the following page for the required maintenance intervals.

At Every Oil Change Interval As Indicated By Oil Change Indicator System:

• Change oil and filter.

• Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil

indicator system turns on.

• Inspect battery and clean and tighten terminals as required.

• Inspect automatic transmission fluid if equipped with dipstick.

• Inspect brake pads, shoes, rotors, drums, hoses and park brake.

• Inspect engine cooling system protection and hoses.

• Inspect exhaust system.

• Inspect engine air cleaner if using in dusty or off-road conditions.

Page 93

MAINTAINING YOUR VEHICLE

150,000

140,000

130,000

120,000

110,000

100,000

90,000

80,000

70,000

60,000

50,000

40,000

240,000

224,000

208,000

192,000

176,000

160,000

144,000

128,000

112,000

96,000

80,000

64,000

30,000

20,000

Mileage or time passed (whichever comes first)

Maintenance Chart

Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15

48,000

32,000

Or Kilometers:

Additional Inspections

XXXX X X X

Inspect the CV joints. X X X X X

Inspect front suspension, tie rod ends, boot

seals and replace if necessary.

Inspect the brake linings, replace as

necessary.

Adjust parking brake as necessary X X X X X X X

Additional Maintenance

Replace engine air filter. X X X X X

Replace cabin/air conditioning filter. X X X X X X X

Replace spark plugs (2.4L Engine). ** X X X X X

Replace spark plugs (2.4L PZEV Engine Only). ** X

Replace spark plugs (3.6L Engine). ** X

Flush and replace the engine coolant at 10 years

or 150,000 miles (240,000 km) whichever

comes first.

Change automatic transmission fluid and filter

if using your vehicle for any of the following:

police, taxi, fleet, or frequent trailer towing.

Page 94

MAINTAINING YOUR VEHICLE

150,000

140,000

130,000

120,000

110,000

100,000

90,000

80,000

70,000

60,000

50,000

40,000

240,000

224,000

208,000

192,000

176,000

160,000

144,000

128,000

112,000

96,000

80,000

64,000

WARNING!

Mileage or time passed (whichever comes first)

30,000

20,000

Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15

48,000

32,000

Or Kilometers:

Change automatic transmission fluid and filter. X

equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.

performance. This could cause an accident.

• You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right

Inspect and replace PCV valve if necessary. X

** The spark plug change interval is mileage based only, yearly intervals do not apply.

• Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and

Page 95

Service Center

Odometer Date Signature, Authorized

90,000 Miles

MAINTAINING YOUR VEHICLE

(144,000 km) or

9 Years

100,000 Miles

(160,000 km) or

10 Years

110,000 Miles

(176,000 km) or

11 Years

120,000 Miles

(192,000 km) or

12 Years

130,000 Miles

(208,000 km) or

13 Years

140,000 Miles

(224,000 km) or

14 Years

150,000 Miles

(240,000 km) or

15 Years

Service Center

Odometer Date Signature, Authorized

MAINTENANCE RECORD

20,000 Miles

(32,000 km) or

2 Years

30,000 Miles

(48,000 km) or

3 Years

40,000 Miles

(64,000 km) or

4 Years

50,000 Miles

(80,000 km) or

5 Years

60,000 Miles

(96,000 km) or

6 Years

70,000 Miles

(112,000 km) or

7 Years

80,000 Miles

(128,000 km) or

8 Years

Page 96

MAINTAINING YOUR VEHICLE

FUSES

Integrated Power Module (fuses)

• The Integrated Power Module (fuses) is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses.

Cavity Cartridge Fuse Mini Fuse Description

1 40 Amp Green

2 20 Amp Yellow Brake Vacuum Pump

3 10 Amp Red

4 10 Amp Red Battery Feed — Ignition Switch 5 20 Amp Yellow Trailer Tow — If Equipped 6 10 Amp Red Power Mirror Switch/Climate Controls 7 30 Amp Green Ignition Off Draw (IOD) Sense 1 8 30 Amp Green Ignition Off Draw (IOD) Sense 2

9 40 Amp Green

10 20 Amp Yellow

11 15 Amp Lt. Blue

13 20 Amp Yellow Ignition/Cigar Lighter 14 10 Amp Red Instrument Panel 15 40 Amp Green Battery Feed — Radiator Fan Relay 16 15 Amp Lt. Blue Sunroof- If Equipped

Power Top Module (If Equipped)

Battery Feed — Center High Mounted Stop Light (CHMSL)/Brake Switch

Battery Feed — Power Seats if equipped

Instrument Panel/Power Locks/ Interior Lights

Selectable Power Outlet (Inside Center Armrest)

Page 97

MAINTAINING YOUR VEHICLE

Cavity Cartridge Fuse Mini Fuse Description

17 10 Amp Red

18 40 Amp Green

19 20 Amp Yellow

20 15 Amp Lt. Blue Ignition Off Draw (IOD) — Radio 21 10 Amp Red Siren — If Equipped

22 10 Amp Red

23 15 Amp Lt. Blue Auto Shutdown (ASD) Relay Feed 3 24 25 Amp Natural Battery Feed — PWR Sunroof Feed

25 10 Amp Red

26 15 Amp Lt. Blue Auto Shutdown (ASD) Relay Feed 2

27 10 Amp Red

28 10 Amp Red

29 — — Hot Car (No Fuse Required)

30 20 Amp Yellow

31 — Spare 32 30 Amp Pink Auto Shutdown (ASD) Relay Feed 1

33 10 Amp Red

34 30 Amp Pink

35 40 Amp Green

36 30 Amp Pink

37 25 Amp Natural Power Top Module (If Equipped)

Ignition Off Draw (IOD) — Wireless Control Module (WCM)/Clock/Steering Control Module (SCM)

Battery Feed — Auto Shutdown (ASD) Relay

Ignition Off Draw (IOD) — Power Amp Feed2-ifequipped

Ignition Run — Climate Controls/Hot Cupholder - if equipped

Ignition Run — Heated Mirrors If Equipped

Ignition Run — Occupant Classification Module (OCM)/Occupant Restraint Controller (ORC)

Ignition Run — Heated Seats If Equipped

Battery Feed — Switch Bank/ Diagnostic Link Connector/Powertrain Control Module (PCM)

Battery Feed — Anti-Lock Brakes (ABS) Module - if equipped/Electronic Control Program (ESC) Module If Equipped

Battery Feed — Anti-Lock Brakes (ABS) Module - If Equipped/Electronic Stability Control (ESC) Module If Equipped

Battery Feed — Passenger Door Module (PDM)/Driver Door Module (DDM)

Page 98

MAINTAINING YOUR VEHICLE

TIRE PRESSURES

• Check the inflation pressure of each tire, including the spare tire, at least monthly and inflate to the recommended pressure for your vehicle.

• The tire pressures recommended for your vehicle are found on the “Tire and Loading Information” label located on the driver’s side door opening.

NOTE:

Refer to the Owner's Manual on the DVD for more information regarding tire warnings and instructions.

WARNING!

• Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.

• Improperly inflated tires are dangerous and can cause collisions. Under-inflation is the leading cause of tire failure and may result in severe cracking, component separation, or “blow out”. Over-inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. Unequal tire pressures can cause steering problems. You could lose control of your vehicle. Over-inflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control.

WHEEL AND WHEEL TRIM CARE

• All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion.

• To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner.

CAUTION!

Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel's protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel's protective finish. Only MOPAR® Wheel Cleaner or equivalent is recommended.

Page 99

MAINTAINING YOUR VEHICLE

EXTERIOR BULBS

LIGHT BULBS – Exterior Bulb Number

Low Beam Headlamp 9006 High Beam Headlamp 9005 Front Park/Turn Signal Lamp 3457A Front Fog Lamp H11 Front Side Marker Lamp WY5W Center High Mounted Stop (CHMSL) Lamp LED (Serviced at Authorized Dealer) Rear Tail/Stop/Turn Signal Lamp LED (Serviced at Authorized Dealer) Backup Lamp 921 License Lamp W5W

Page 100

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC CUSTOMER CENTER

P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–800–423–6343

CHRYSLER CANADA INC. CUSTOMER CENTER

P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French)

ASSISTANCE FOR THE HEARING IMPAIRED

•

To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf ) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY. Canadian residents with hearing difficulties that require assistance can use the specialneeds relay service offered by BellCanada. For TTY teletypewriter users,dial 711 and for Voice callers, dial 1–800–855–0511 to connect with a Bell Relay Service operator.

WARNING!

Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wearcontain,or emit, chemicals knownto the State ofCalifornia to cause cancer and birth defects, or other reproductive harm.

PUBLICATIONS ORDERING

• If you are the first registered retail owner of your vehicle, you may obtain one free printed copy of the Owner's Manual, Warranty Booklet or Radio Manuals on your DVD by calling 1–800–423–6343 (U.S.) or 1–800–387–1143 (Canada) or by contactingyour dealer.

•

Replacement User Guide kits or DVDs or, if you prefer, additional printed copies of the Owner's Manual, Warranty Booklet or Radio Manuals may be purchased by visiting www.techauthority.com or by calling 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada). Visa, Master Card,American Express and Discoverorders are accepted. Ifyou prefer mailing your order, please call the above numbers for an order form.

NOTE:

• A street address is required when ordering manuals (no P.O. Boxes).

• The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep, Ram Truck and Dodge websites.

• Click on the “For Owners” tab, select “Owner/Service Manuals”, then select your desired model year and vehicle from the drop down lists.

Dodge Avenger 2013 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

VEHICLES SOLD IN CANADA

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

CONTROLS AT A GLANCE

DRIVER COCKPIT

INSTRUMENT CLUSTER

Warning Lights

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors

Opening The Trunk

Panic Alarm

REMOTE START

THEFT ALARM

To Arm:

To Disarm:

SEAT BELT

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

CHILD RESTRAINTS

Installing The LATCH-Compatible Child Restraint System

Installing The Child Restraint Using The Vehicle Seat Belts

FRONT SEATS

Power Seat

Manual Seat Adjustment

REAR SEATS

Folding Rear Seatback

HEATED SEATS

Front Heated Seats

TILT/TELESCOPING STEERING COLUMN

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

TURN SIGNAL/LIGHTS LEVER

Headlights/Parking Lights/Automatic Headlights

Instrument Panel Dimmer

Flash To Pass

High Beam Operation

Front Fog Lights

Turn Signals/Lane Change Assist

WIPER/WASHER LEVER

Front Wipers

SPEED CONTROL

Cruise ON/OFF

Accel/Decel

Resume

Cancel

MANUAL CLIMATE CONTROLS

Air Recirculation

Heated Mirrors

AUTOMATIC TEMPERATURE CONTROLS (ATC)

Automatic Operation

Air Conditioning (A/C)

Air Recirculation

Heated Mirrors

POWER SUNROOF

Manual Open/Close

Pinch Protection Feature

WIND BUFFETING

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM

Uconnect® 130

Clock Setting

Equalizer, Balance And Fade

Radio Operation

CD/DISC Operation

Audio Jack Operation

Uconnect® 130 WITH SiriusXM SATELLITE RADIO

Clock Setting

Equalizer, Balance And Fade

Radio Operation

SiriusXM Satellite Radio

CD/DISC Operation

Audio Jack Operation

Uconnect® 430/430N

Clock Setting