Dodge Automobile Accessories TA0 - TA3 User Manual

Installation and Instruction Manual For

Dodge® TORQUE-ARM II

™

Vertical Breather Kit

TA0 – TA3

and

TA4 – TA12

WARNING: Because of the possible danger to person(s) or property from accidents which may result from the improper use of products, it
is important that correct procedures be followed. Products must be used in accordance with the engineering information specifie d in the
catalog. Proper installation, maintenance and operation procedures must be observed. The instructions in the instruction manuals must be
followed. Inspections should be made as necessary to assure safe operation under prevailing conditions. Proper guards and other suitable
safety devices or procedures, as may be desirable, or as may be specified in safety codes should be provided, and are neither provided by
Baldor Electric Company, nor are the responsibility of Baldor Electric Company. This unit and its associated equipment must be installed,
adjusted and maintained by qualified personnel who are familiar with the construction and operation of all equipment in the system and the
potential hazards involved. When risks to persons or property may be involved, a holding device must be an integral part of the driven
equipment beyond the speed reducer output shaft.

www.baldor.com www.ptplace.com www.dodge-pt.com www.reliance.com

Baldor Electric Company Headquarters

P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.648.5792, Fax [phone], International Fax [phone]

DODGE/Reliance Division

6040 Ponders Court, Greenville, SC 29615-4617 U.S.A., Ph: (1) 864.297.4800, FAX: [phone]

IM499387 04/07-1M-K Copyright © 2007 Baldor Electric Company All Rights Reserved. Printed in USA.

This material is not intended to provide operational instructions. Appropriate instruction
manuals and precautions should be studied prior to installation, operation or maintenance of
equipment.

INSTALLATION

y

WARNING: To ensure that drive is not unexpectedly started,
turn off and lock out or tag power source before proceeding.
Remove all external loads from drive before removing or
servicing drive or accessories. Failure to observe these
precautions could result in bodil

injury.

Where space contraints prevent installing the breather in vent
locations 5 for Position E or location 6 for Position F (see Figure

1), install vertical breather kit in location 2 for Position E or location
4 for Position F.

Figure 1–Reducer Mounting Positions

Table 1 - Parts for Vertical Breather Kit

Table 1–Parts for Vertical Breather Kit

Ref. No* Part Description Part No.

1 Air Vent Assembly TAO - TA3 241237 1 ---

Air Vent Assembly TA4 TA12 245237 --- 1

2 3/8 Pipe Coupling A31484 1 ---

1/2 Pipe Coupling A45622 --- 1

3 3/8 x 90°Street Ell A38815 1 ---

1/2 x 90° Street Ell A38817 --- 1

4** 3/8 x 1 1/2 Pipe Nipple A38847 1 ---

1/2 x 1 1/2 Pipe Nipple A38845 --- 1

5** 3/8 x 3 Pipe Nipple A31570 1 ---

1/2 x 3 Pipe Nipple 304596 --- 1

6*** 3/4 x 1/2 Hex Bushing 430079 --- 1

Figure 2 – Vertical Breather Kit Assembly

Refer to Table 1 for Dodge replacement part numbers and
pardescriptions.

Refer to Table 1 for Dodge replacement part numbers
and part descriptions.

Qty.

TA0–TA3 (900112) TA4–TA12 (904112)

* Refer to Figure 2.
** Two lengths of pipe nipple are provided. Only one is required. Use length best suited to application and discard the other.
*** Not shown. This part is used only on TA4 – TA12 reducers to adapt 3/4 NPT hole to 1/2 pipe nipple.