D Link DWL8200APA1 Users Manual
DWL-8200AP User’s Manual |
Networking Basics |
Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, using Microsoft
Windows XP.
Note: Please refer to websites such as http://www.homenethelp.com
and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000.
Go to Start>Control Panel>Network Connections
Select Set up a home or small office network
When this screen appears, click Next.
D-Link Systems, Inc. |
100 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Please follow all the instructions in this window:
Click Next.
In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown.
Click Next.
D-Link Systems, Inc. |
101 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Enter a Computer description and a Computer name (optional).
Click Next.
Enter a Workgroup name. All computers on your network should have the same
Workgroup name.
Click Next.
D-Link Systems, Inc. |
102 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Please wait while the Network Setup Wizard applies the changes.
When the changes are complete, click Next.
Please wait while the Network Setup Wizard configures the computer.This may take a few minutes.
D-Link Systems, Inc. |
103 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next.
Insert a disk into the Floppy Disk Drive, in this case drive A.
Click Next.
D-Link Systems, Inc. |
104 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Please read the information under Here’s how in the screen below.After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click
Next.
D-Link Systems, Inc. |
105 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Please read the information on this screen, then click Finish to complete the Network Setup Wizard.
The new settings will take effect when you restart the computer. Click Yes to restart the computer.
You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
D-Link Systems, Inc. |
106 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
Naming Your Computer
To name your computer n Windows XP, please follow these directions.
Click Start (in the lower left corner of the screen).
Right-click on My Computer.
Select Properties and click.
Select the Computer Name Tab in the System Properties window.
You may enter a Computer Description if you wish; this field is optional.
To rename the computer and join a domain, Click Change.
D-Link Systems, Inc. |
107 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
In this window, enter the Computer name.
Select Workgroup and enter the name of the Workgroup.
All computers on your network must have the same Workgroup name.
Click OK.
Checking the IP Address in Windows XP
The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.) To check on the IP Address of the adapter, please do the following:
Right-click on the Local Area Connection icon in the task bar.
Click on Status.
D-Link Systems, Inc. |
108 |
DWL-8200AP User’s Manual |
Networking Basics |
|
|
|
|
This window will appear:
Click the Support tab.
Click Close.
D-Link Systems, Inc. |
109 |
Loading...