D-Link DSL524T User Manual

DSL-524T
ADSL Router
(March 2005)
DSL524TEUA1
User’s Guide
DSL-524T ADSL Router Manual
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo case, puede requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati.
ii
DSL-524T ADSL Router Manual
Warranty and Registration for all Countries and Regions Except USA
Wichtige Sicherheitshinweise
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den spätern Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind.
5. Das Gerät is vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben.
10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch nichts auf der Leitung abgestellt werden.
11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
12. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
13. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. Elektrischen Schlag auslösen.
14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sint beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung ensprechend funktioniert oder Sie mit Hilfe dieser Anleitung
keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. den Orginalteilen entsprechende Teile verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere Beschädigung hervorrufen.
17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.
18. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen Nennstrom bis 6A und einem Gerätegewicht grőßer 3kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen.
WARRANTIES EXCLUSIVE
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D­LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF D-LINK'S PRODUCTS. D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD.
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Limited Warranty
Hardware:
iii
DSL-524T ADSL Router Manual
D-Link warrants each of its hardware products to be free from defects in workmanship and materials under normal use and service for a period commencing on the date of purchase from D-Link or its Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D-Link Branch Office nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card.
If the product proves defective within the applicable warranty period, D-Link will provide repair or replacement of the product. D-Link shall have the sole discretion whether to repair or replace, and replacement product may be new or reconditioned. Replacement product shall be of equivalent or better specifications, relative to the defective product, but need not be identical. Any product or part repaired by D-Link pursuant to this warranty shall have a warranty period of not less than 90 days, from date of such repair, irrespective of any earlier expiration of original warranty period. When D-Link provides replacement, then the defective product becomes the property of D-Link.
Warranty service may be obtained by contacting a D-Link office within the applicable warranty period, and requesting a Return Material Authorization (RMA) number. If a Registration Card for the product in question has not been returned to D-Link, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided. If Purchaser's circumstances require special handling of warranty correction, then at the time of requesting RMA number, Purchaser may also propose special procedure as may be suitable to the case.
After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. The package must be mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never be responsible for any software, firmware, information, or memory data of Purchaser contained in, stored on, or integrated with any product returned to D-Link pursuant to this warranty.
Any package returned to D-Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs.
Software:
Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service. The term "purchase" in this software warranty refers to the purchase transaction and resulting license to use such software.
D-Link warrants that its software products will perform in substantial conformance with the applicable product documentation provided by D-Link with such software product, for a period of ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link warrants the magnetic media, on which D-Link provides its software product, against failure during the same warranty period. This warranty applies to purchased software, and to replacement software provided by D-Link pursuant to this warranty, but shall not apply to any update or replacement which may be provided for download via the Internet, or to any update which may otherwise be provided free of charge.
D-Link's sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to D-Link's applicable product documentation. Purchaser assumes res ponsibility for the selection of appropriate application and syst em/platform software and associated reference materials. D-Link makes no warranty that its software products will work in combination with any hard ware, or any application or system/platform software product provided by any third party, excepting only such products as are expressly represented, in D-Link's applicable product documentation as being compatible. D-Link's obligation under this warran ty shall be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide compatibility when there is fault in the third-party hardware or software. D-Link makes no warranty that operation of its software products will be uninterrupted or absolutely error-free, and no warranty that all defects in the software product, within or without the scope of D-Link's applicable product documentation, will be corrected.
Warranty and Registration Information for USA Only
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the product from:
D-Link or its authorized reseller or distributor and Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will be free from material defects in workmanship and materials from the date of original retail purchase of the product, for the period set forth below applicable to the product type (“Warranty Period”), except as otherwise stated herein. 5-Year Limited Warranty for the Product(s) is defined as follows:
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is
or Protectorates, and U.S. Military Installations, addresses with an APO or FPO.
Hardware (excluding power supplies and fans) Five (5) Years Power Supplies and Fans Three (3) Year Spare parts and spare kits Ninety (90) days
iv
DSL-524T ADSL Router Manual
incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund. Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. D-Link’s sole obligation shall be to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software or to refund at D-Link’s sole discretion. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Software will be warranted for the remainder of the original Warranty Period from the date or original retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates. Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of D-Link's products, will not be applied to and does not cover any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold "As-Is" without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary. Submitting A Claim: Any claim under this limited warranty must be submitted in writing before the end of the Warranty Period to an Authorized D-Link Service Office.
The customer must submit as part of the claim a written description of the Hardware defect or Software nonconformance
in sufficient detail to allow D-Link to confirm the same.
The original product owner must obtain a Return Material Authorization (“RMA”) number from the Authorized D-Link
Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the warranty service is provided.
After an RMA number is issued, the defective product must be packaged securely in the original or other suitable
shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the Product and will not ship back any accessories.
The customer is responsible for all shipping charges to D-Link. No Charge on Delivery (“COD”) is allowed. Products sent
COD will either be rejected by D-Link or become the property of D-Link. Products should be fully insured by the customer and shipped to D-Link Systems, Inc., 53 Discovery Drive, Irvine, CA 92618. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped via UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited shipping is available if shipping
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming. What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT. Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D­LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state.
Notice of IEEE802.11a 5Ghz radio usage in the European Community
charges are prepaid by the customer.
At the time of writing this addendum, some countries such as Italy, Greece, Portugal and Spain hasn’t allowed operation of radio devices in the 5Ghz bands, although operation of 2.4Ghz radio devices are allowed. Please check with your local authority to confirm.
v
DSL-524T ADSL Router Manual
This device is restricted to indoor use when operated in the European Community using channels in the 5.15-5.35 GHz band to reduce the potential for interference.
Usage Notes:
To remain in conformance with European National spectrum usage regulations, frequency and channel limitations will be applied on the products according to the country where the equipment will be deployed.
This device is restricted from functioning in Ad-hoc mode while operating in 5Ghz. Ad-hoc mode is direct peer-to-peer communication between two client devices without an Access Point.
Access points will support DFS (Dynamic Frequency Selection) and TPC (Transmit Power Control) functionality as required when operating in 5Ghz within the EU.
Allowable 802.11a Frequencies and Channels
5.15-5.25 GHz (Channels 36, 40, 44, 48)
5.15-5.25 Ghz & 5.725-5.87 5 Ghz (Channels 36, 40, 44, 48, 14 9, 153, 157, 161, 165, 169)
5.15-5.35 GHz (Channels 36, 40, 44, 48, 52, 56, 60, 64)
5.15-5.35 & 5.47-5.725 GHz (Channels 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140)
5.15-5.35 Ghz & 5.725-5.87 5 Ghz (Channels 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165, 169)
IEEE 802.11b 2.4Ghz operation
2.4-2.4835 Ghz Rest of EU Community
2.4465-2.4835 Ghz (Channels 10,11,12,13)
European Community Declaration of Conformity:
English Hereby, D-Link Corporation declares that this Wireless LAN device is in compliance w ith the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Countries
Liechtenstein, Hungary, Switzerland
Austria
France, Slovak
Denmark, Germany, Iceland, Finland, Netherlands, Norway, Poland, Sweden, Slovenia, Luxembourg, U.K., Ireland
Czech Republic
Countries
France
Finnish Valmistaja D-Link Corporation vakuuttaa täten että Wireless LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten
Dutch
French
Swedish Härmed intygar D-Link Corporation att denna Wireless LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga
Danish Undertegnede D-Link Corporation erklærer herved, at følgende udstyr Wireless LAN device overholder de væsentlige krav og øvrige
German
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Hierbij verklaart D-Link Corporation dat het toestel Wireless LAN device in ove reenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG
Bij deze verklaart D-Link Corporation dat deze Wireless LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
Par la présente D-Link Corporation déclare que l'appareil Wireless LAN device est conforme aux exigences essentie lles et aux autres dispositions pertinentes de la directive 1999/5/CE
Par la présente, D-Link Corporation déclare que ce Wireless LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
relevante krav i direktiv 1999/5/EF
Hiermit erklärt D-Link Corporation dass sich dieser/diese/dieses Wireless LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)
Hiermit erklärt D-Link Corporation die Übereinstimmung des Gerätes Wireless LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)
Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑD-Link Corporation ∆ΗΛΩΝΕΙ ΟΤΙ Wireless LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ
vi
DSL-524T ADSL Router Manual
9
Italian Con la presente D-Link Corporation dichiara che questo Wireless LAN device è conforme ai requisiti essenziali ed alle altre disposizioni
Spanish Por medio de la presente D-Link Corporation declara que el Wireless LAN device cumple con los requisitos esenciales y cualesquiera
Portuguese D-Link Corporation declara que este Wireless LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 199
pertinenti stabilite dalla direttiva 1999/5/CE.
otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE
AVERTISSEMENT AUX UTILISATEURS
L’utilisation des bandes de fréquences des 2.4GHz et 5GHz pour les RLAN est réglementée par l’ART (Autorité de Régulation des Télécoms). BANDE DE FREQUENCES DES 2.4GHZ La décision N° 02-1008 en date du 31 octobre 2002 autorise l’utilisation d’une partie de la bande de fréquences 2400-2483,5 MHz pour les réseaux locaux radioéléctriques (RLAN) comme suit :
L’utilisation de la bande 2400-2446,5 MHz est autorisée à l’intérieur des bâtiments avec une puissance isotrope rayonnée équivalente (PIRE) limitée à 10 mW et que l’utilisation de la bande 2446,5-2483,5 MHz est autorisée à l’intérieur des bâtiments avec une PIRE limitée à 100 mW. L’utilisation en extérieur est soumise à demande d’autorisation sur la bande de fréquences de 2446,5-2483,5 MHz avec une puissance limitée à 100mW. Dans certains départements, dont la liste est publiée par l'Autorité de régulation des télécommunications, l'utilisation de la totalité de la bande 2400- 2483,5 MHz est autorisée à l'intérieur des bâtiments avec une puissance isotrope rayonnée équivalente maximale de 100 mW. Dans ces mêmes départements, l'utilisation de la bande 2400-2454 MHz est autorisée à l'extérieur des bâtiments avec une puissance isotrope rayonnée équivalente maximale de 100 mW et l'utilisation de la bande 2454-2483,5 MHz est autorisée à l'extérieur des bâtiments avec une puissance isotrope rayonnée équivalente maximale de 10 mW. L’Autorité poursuit les négociations avec le ministère de la Défense en vue de l’ouverture de la totalité de la bande 2400-2483,5 MHz en intérieur et en extérieur avec une PIRE de 100 mW. Cette ouverture est acquise d'ores et déjà dans certains départements d'Outre-mer. En installant et utilisant les produits réseaux sans fils de la gamme proposée par D-Link, vous vous engagez donc à respecter cette réglementation.
Pour tour information complémentaire et les dernières informations concernant l’évolution de la réglementation française, nous vous conseillons de consulter le site de l’ART : www.art-telecom.fr.
BANDE DE FREQUENCES DES 5GHZ
L’Autorité de Régulation des Télécommunications (ART) autorise l’utilisation d’une partie de la bande de fréquences des 5GHz pour les réseaux locaux radioélectriques (RLAN) intégrant des solutions 802.11a supportant les fonctions DFS (Dynamic Frequency Selection) et TPC (Transmit Power Control).
Seule la bande 5150-5350MHz est autorisée en France pour une utilisation intérieure avec une puissance limitée à 200 mW en mode infrastructure.
En installant et en utilisant les produits réseaux sans fil 802.11a de la gamme D-Link commercialisée en France, vous vous engagez à respecter cette réglementation.
Pour tour information complémentaire et les dernières informations concernant l’évolution de la réglementation française, nous vous conseillons de consulter le site de l’ART : www.art-telecom.fr.
AVVERTIMENTI PER GLI UTILIZZATORI
L’utilizzo della banda di frequenza dei 2.4 GHz per applicazioni di tipo Radio LAN sul mercato Italiano, è regolamentato dal Ministero delle Comunicazioni secondo il Nuovo Piano Nazionale Gestioni Frequenze relativo al D.M. dell’8 Luglio 2002 e dalle relative modifiche come dal Decreto del Ministero delle Comunicazioni del 20 Febbraio 2003 (nota 158).
Viene definito come Radio Local Area Network (di seguito denominate “Radio LAN” o “R-LAN”) un sistema di comunicazioni in rete locale mediante radiofrequenze che utilizza apparati a corto raggio secondo le caratteristiche di armonizzazione e tecniche previste dal vigente Piano nazionale di ripartizione delle frequenze, nelle seguenti bande di frequenza: 2.400,0 – 2.483,5 MHz (brevemente banda a 2.4 GHz).
I sistemi Radio LAN sono regolati da apposite normative. Principalmente valgono le normative F.C.C. per gli U.S.A., il Canada, e gli altri paesi aderenti alle F.C.C., come gli ex paesi U.R.S.S.; mentre le norme E.T.S. 300T-328-2 e correlate, emanate dall'organo Europeo E.T.S.I., valgono per i paesi dell'Unione Europea, Giappone e per i paesi aderenti a queste normative.
La normativa tecnica ETS 300T-328-2 impone di non irradiare con una potenza E.I.R.P. superiore ai 100 mW (equivalente a 20 dBm).
In linea di principio inoltre impone agli apparati Radio LAN, di non trasmettere con una potenza elettrica effettiva superiore ai 50 mW (equivalente a 17 dBm); questo perché l'antenna a dipolo più semplice, che di solito li accompagna, ha generalmente un guadagno in trasmissione pari a circa 2.5 dBi, che fa si che la potenza E.I.R.P. trasmessa salga a circa 80 mW (per la precisione 19.2 dBm).
vii
DSL-524T ADSL Router Manual
Per questo motivo su tutto il territorio dell'Unione Europea, ed anche in Italia, è assolutamente vietato utilizzare antenne che abbiano un guadagno in trasmissione elevato (in linea di massima diciamo superiore ai 5 dBi), tale da portare la potenza trasmessa E.I.R.P. oltre i 100 mW (equivalente a 20 dBm).
Nel caso in cui invece sia possibile regolare il livello di potenza trasmessa dagli Access Point, viene data la possibilità di utilizzare antenne ad alto guadagno attenendosi strettamente ad una serie di istruzioni di seguito riportate che consentono questo utilizzo rimanendo comunque all’interno della potenza massima trasmessa E.I.R.P. pari e non superiore a 100mW (20dBm).
CALCOLO DELLA POTENZA E.I.R.P. IN EMISSIONE
La formula di calcolo per ottenere l’E.I.R.P. effettivo è la seguente:
Ptx = Potenza trasmessa al connettore dell’antenna di trasmissione Gtx = Guadagno dell’antenna di trasmissione
Il valore ottenuto dalla somma, NON deve superare quanto espresso dalla normativa ovvero 20dBm. Nel caso in cui si voglia convertire il risultato ottenuto in mW, utilizzare la semplice tabella di conversione di seguito riportata.
E.I.R.P. (dBm) = Ptx (dBm) + Gtx (dBi) dove
INSTALLAZIONE ED UTILIZZO DI SITEMI RADIO LAN AD USO PRIVATO
Come riportato nel D.P.R. n° 447/01 Art. 6 – Punto B (Libero uso) del 5 Ottobre 2001: “Sono di libero uso le apparecchiature che impiegano frequenze di tipo collettivo, senza alcuna protezione, per
collegamenti a brevissima distanza con apparati a corto raggio, compresi quelli rispondenti alla raccomandazione CEPT-ERC/REC 70-03, tra le quali rientrano in particolare:
b) Reti locali di tipo radiolan e hiperlan nell’ambito del fondo, ai sensi dell’articolo 183, comma secondo, del
decreto del Presidente della Repubblica n. 156 del 1973; sono disciplinate ai sensi dell’articolo 5 le reti
… Per “fondo” pubblico o privato, si intende un ambiente sia interno che esterno ben circoscritto e delimitato. Per “fondo privato” possiamo, per esempio, fare riferimento a uffici, capannoni industriali, abitazioni, aree all’aperto private che non attraversano il suolo pubblico o il passaggio di pubblico dominio/demanio. Per “fondo pubblico” possiamo, per esempio, fare riferimento a tutti quei luoghi appartenenti allo Stato o alle amministrazioni centrali e locali quali strade, autostrade, strade ferrate, spiagge, porti, fiumi etc.
E’ comunque necessario fare 2 specifiche distinzioni:
Utilizzo di sistemi Radio LAN ad uso privato con installazioni indoor o outdoor su fondo/suolo privato: E’ possibile utilizzare liberamente sistemi Radio LAN purché vengano rispettate le normative vigenti soprattutto per quanto riguarda l’emissione massima in potenza come sopra riportato.
Utilizzo di sistemi Radio LAN ad uso privato con installazioni outdoor con attraversamento di fondo/suolo pubblico:
Come specificato nel D.P.R. n° 447/01 Art. 5 – Punto 2.2 del 5 Ottobre 2001, è necessario richiedere un’autorizzazione generale al “Ministero delle Comunicazioni Direzione generale per le concessioni e le autorizzazioni” per l’installazione di sistemi Radio LAN ad uso privato con installazioni outdoor con attraversamento di suolo pubblico. Per richiedere l’autorizzazione generale, fare riferimento all’allegato C presente all’interno del D.P.R. n° 447/01 in qualità di canovaccio per la stesura della richiesta. Per ulteriori informazioni e delucidazioni, fare riferimento al D.P.R. n° 447/01 del 5 Ottobre 2001.
hiperlan operanti obbligatoriamente in ambienti chiusi o con vincoli specifici
INSTALLAZIONE ED UTILIZZO DI SITEMI RADIO LAN AD USO PUBBLICO
viii
DSL-524T ADSL Router Manual
A fronte dell’ultimo decreto relativo all’accesso ad Internet senza fili in regime di autorizzazione generale e uso pubblico
rilasciato dal Ministero delle Comunicazioni in data 28 Maggio 2003, sono stati rivisti i parametri relativi all’installazione ed all’utilizzo dei sistemi Radio LAN ad uso pubblico. Per completezza di informazioni, suggeriamo di fare riferimento al decreto in questione disponibile sul sito del Ministero delle Comunicazioni al link http://www.comunicazioni.it/it/index.php?IdNews=39
ACCESSO ALLE FONTI DI INFORMAZIONE
Per tutte le informazioni complementari, a supporto di questa informativa e concernenti all’evoluzione della normativa wireless sul territorio italiano, vi preghiamo di fare riferimento al sito Internet del Ministero delle Comunicazioni http://www.comunicazioni.it
ix
TABLE OF CONTENTS
About This User’s Guide....................................................................................................................................12
Before You Start ................................................................................................................................................12
Installation Requirements...................................................................................................................................12
INTRODUCTION.......................................................................................................15
Router Description and Operation......................................................................................................................15
Front Panel.........................................................................................................................................................17
Rear Panel..........................................................................................................................................................18
HARDWARE INSTALLATION..................................................................................19
Location .............................................................................................................................................................19
Network Connection ..........................................................................................................................................19
Power On Router................................................................................................................................................20
Factory Reset Button..........................................................................................................................................20
CONFIGURING THE ROUTER FOR THE FIRST TIME ...........................................21
Configuring IP Settings on Your Computer.......................................................................................................21
Configure IP Settings.........................................................................................................................................22
ACCESSING THE CONFIGURATION MANAGER...................................................24
Configure the Router with the Configuration Wizard........................................................................................25
HOME........................................................................................................................36
WAN Configuration...........................................................................................................................................36
LAN Configuration............................................................................................................................................45
DHCP.................................................................................................................................................................46
DNS....................................................................................................................................................................49
Dynamic DNS....................................................................................................................................................50
ADVANCED CONFIGURATION...............................................................................51
UPnP..................................................................................................................................................................51
Virtual Server.....................................................................................................................................................52
LAN Clients.......................................................................................................................................................54
SNMP.................................................................................................................................................................56
Filters .................................................................................................................................................................58
Bridge Filters......................................................................................................................................................60
Routing Table.....................................................................................................................................................62
DMZ...................................................................................................................................................................64
Firewall ..............................................................................................................................................................66
RIP .....................................................................................................................................................................68
PPP.....................................................................................................................................................................69
ADSL.................................................................................................................................................................71
ATM VCC..........................................................................................................................................................73
QoS ....................................................................................................................................................................74
TOOLS......................................................................................................................76
Admin ................................................................................................................................................................76
Time...................................................................................................................................................................77
Remote Log........................................................................................................................................................78
System................................................................................................................................................................80
Firmware............................................................................................................................................................81
Miscellaneous.....................................................................................................................................................82
Test.....................................................................................................................................................................82
STATUS ....................................................................................................................85
Device Info.........................................................................................................................................................85
DHCP.................................................................................................................................................................87
Log.....................................................................................................................................................................88
Statistics.............................................................................................................................................................89
ADSL.................................................................................................................................................................90
Help ....................................................................................................................................................................91
TECHNICAL SPECIFICATIONS...............................................................................94
IP ADDRESS SETUP................................................................................................96
IP CONCEPTS ..........................................................................................................99
MICROFILTERS AND SPLITTERS ........................................................................103
DSL-524T ADSL Router Manual
About This User’s Guide
This manual provides instructions on how to install the DSL-524T ADSL Router and use it to connect a computer or Ethernet LAN to the Internet.
Before You Start
Please read and make sure you understand all the prerequisites for proper installation of your new Router. Have all the necessary information and equipment on hand before beginning the installation.
Installation Overview
The procedure to install the Router can be described in general terms in the following steps:
1. Gather information and equipment needed to install the device. Before you begin the actual installation make sure you have all the necessary information and equipment.
2. Install the hardware, that is, connect the cables (Ethernet and telephone) to the device and connect the power adapter.
3. Check the IP settings on your computer and change them if necessary so the computer can access the web-based software built into the Router.
4. Use the web-based management software to configure the device to suit the requirements of your ADSL account.
Installation Requirements
Information you will need from your ADSL service provider:
This is the Username that is used to log on
Username
Password
Connection Protocol
VPI
VCI
to your ADSL service provider’s network. It is commonly in the form user@isp.com.
This is the Password that is used, in conjunction with the Username above, to log on to your ADSL service provider’s network.
This is the method that your ADSL service provider uses to send and receive data between the Internet and your computer.
This is the Virtual Path Identifier (VPI). It is used in conjunction with the Virtual Channel Identifier (VCI) below, to identify the data path between your ADSL service provider’s network and your computer.
This is the Virtual Channel Identifier (VCI). It is used in conjunction with the VPI above to identify the data path between your ADSL service provider’s network and your computer.
Record your info here.
12
DSL-524T ADSL Router Manual
Information you will need about your DSL-524T ADSL Router:
This is the Username you will be prompted
Username
to enter when you access the DSL-524T’s configuration screens using a Web browser. The default Username is admin.
Record your info here.
This is the Password you will be prompted to
Password
enter when you access the DSL-524T’s configuration screens using a Web browser. The default Password is admin.
This is the IP address you will enter into the
LAN IP address for the DSL-524T
Address field of your Web browser to
access the DSL-524T’s configuration screens using a Web Browser. The default IP address is 192.168.1.1.
LAN Subnet Mask for the DSL-524T
This is the subnet mask used by the DSL­524T, and will be used throughout your LAN. The default subnet mask is 255.255.255.0.
Information you will need about your LAN or computer:
If your computer has an Ethernet NIC, you can connect the DSL-524T to this Ethernet
Ethernet NIC
port using an Ethernet cable. You can also use the Ethernet port on the DSL-524T to connect to other Ethernet devices, such as a Wireless Access Point.
Record your info here.
Your DSL-524T ADSL Router is configured, by default, to be a DHCP server. This means that it can assign an IP address, subnet mask, and a default gateway address to
DHCP Client status
computers on your LAN. The range of IP addresses the DSL-524T will assign are from
192.168.1.2 to 192.168.1.254. Your computer (or computers) needs to be configured to Obtain an IP address automatically (that is, they need to be configured as DHCP clients.)
It is recommended that your collect and record this information here, or in some other secure place, in case you have to re-configure your ADSL connection in the future. Once you have the above information, you are ready to setup and configure your DSL-524T ADSL Router.
13
DSL-524T ADSL Router Manual
14
DSL-524T ADSL Router Manual
1
Introduction
This section provides a brief description of the Router, its associated technologies and a list of Router features.
What is ADSL?
Asymmetric Digital Subscriber Line (ADSL) is an access technology that utilizes ordinary copper telephone lines to enable broadband high-speed digital data transmission and interactive multimedia applications for business and residential customers. For ADSL services, it is not necessary to install expensive new cabling or condition the line in any way. ADSL greatly increases the signal carrying capacity of copper telephone lines without interfering with regular telephone services. For the ADSL user, this means faster downloads and more reliable connectivity. ADSL devices make it possible to enjoy benefits such as high-speed Internet access without experiencing any loss of quality or disruption of voice/fax telephone capabilities. ADSL provides a dedicated service over a single telephone line operating at speeds of up to 8 Mbps downstream and up to 640 Kbps upstream, depending on local telephone line conditions. A secure point-to-point connection is established between the user and the central office of the service provider. D-Link ADSL devices incorporate the recommendations of the ADSL Forum regarding framing, data format, and upper layer protocols.
Router Description and Operation
The DSL-524T ADSL Router is designed to provide a simple, cost-effective and secure ADSL Internet connection for your small- to medium-sized private network. The DSL-524T combines the benefits of high-speed ADSL connection technology and TCP/IP routing with a conventional Ethernet interface in one compact and convenient package. ADSL connection technology enables many interactive multi-media applications such as video conferencing and collaborative computing. The Router is easy to install and use. The DSL-524T connects to an Ethernet LAN via a standard Ethernet 10BASE-T interface using RJ-45 connectors. The ADSL connection is made using ordinary twisted-pair telephone line with standard RJ-11 connectors. This arrangement means that several PCs can be networked and connected to the Internet using a single WAN interface and IP address.
Low Pass Filters
Since ADSL and telephone services share the same copper wiring to carry their respective signals, a filtering mechanism may be necessary to avoid mutual interference. A low pass filter device can be installed for each telephone that shares the line with the ADSL line. These filters are easy to install passive devices that connect to the ADSL device and/or telephone using standard telephone cable. Ask your service provider for more information about the use of low pass filters with your installation. Appendix B provides illustrated examples of how to install two common styles of low pass filters.
Operating Systems
The DSL-524T uses an HTML-based web interface for setup and management. The web configuration manager may be accessed using any operating system capable of running web browser software, including Windows 98 SE, Windows ME, Windows 2000, and Windows XP.
15
DSL-524T ADSL Router Manual
Web Browser
Any common web browser can be used to configure the Router using the web configuration management software. The program is designed to work best with more recently released browsers such as Mozilla, Firefox, Opera, Microsoft Internet Explorer® version 5.0, Netscape Navigator® version 4.7, or later versions. The web browser must have JavaScript enabled. JavaScript is enabled by default on many browsers. Make sure JavaScript has not been disabled by other software (such as virus protection or web user security packages) that may be running on your computer.
Ethernet Port (NIC Adapter)
Any computer that uses the Router must be able to connect to it through the Ethernet port on the Router. This connection is an Ethernet connection and therefore requires that your computer be equipped with an Ethernet port as well. Most notebook computers are now sold with an Ethernet port already installed. Likewise, most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment. If your computer does not have an Ethernet port, you must install an Ethernet NIC adapter before you can use the Router. If you must install an adapter, follow the installation instructions that come with the Ethernet NIC adapter.
Additional Software
It may be necessary to install software on your computer that enables the computer to access the Internet. Additional software must be installed if you are using what is called a “bridged” connection. For a bridged connection, the information needed to make and maintain the Internet connection is stored on your computer, not in the Router. This type of connection is similar to the arrangement used for analog dial-up modems, but the connection speed is much faster. Various terms are to describe a bridged ADSL connection including the term “RFC 1483 Bridge” which is used in this guide.
About Bridged Ethernet Connections (RFC 1483)
Using this method, the DSL-524T acts as a transparent bridge, and is invisible to other devices on both the WAN and LAN side of the bridge. It is therefore necessary to provide some means of acquiring global IP settings for your account. All connections to the Internet require a unique global IP address. For bridged connections, the global IP settings must reside in a TCP/IP enabled device on the LAN side of the bridge, such as a PC, server or firewall hardware. The IP address can be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required.
Account Information (User Name and Password)
Most users will need to supply a user name and password used to access the service provider’s network (and ultimately, the Internet). This information is stored either in the Router’s memory or on your computer depending on the type of ADSL connection you have.
ACCOUNT INFORMATION (PPP Connections Only) User Name: Password:
Router Features
The D-Link DSL-524T ADSL Router provides the following features:
Data rates up to 24 Mbps for downstream and 1Mbps for upstream
16
DSL-524T ADSL Router Manual
Friendly web-based graphical user interface for configuration and management
Supports up to eight simultaneous virtual connections for a single ADSL account
Supports T1.413 issue 2, G.dmt and G.lite for the ADSL standard
Supports G.dmt.bis and G.lite.bis for the ADSL2 standard
Supports g.992.5 for the ADSL standard
Auto-handshake and rate adaptation for different ADSL flavors
Widest range of DSLAM interoperability
Built-in MIBs for SNMP management
Upgradeable firmware through HTTP
Packing List
Open the shipping carton and carefully remove all items. In addition to this User's Guide, ascertain that you have:
One DSL-524T ADSL Router
One twisted-pair telephone cable used for ADSL connection
One CAT-5 Ethernet cable
One AC power adapter suitable for your electric service
This Manual on CD ROM
Front Panel
Place the Router in a location that permits an easy view of the LED indicators on the front panel.
The LED indicators on the front panel include the Power, Status, ADSL Link/Act(ivity) and Ethernet Link/Act(ivity) indicators.
Power
Status
ADSL: Link/Act
Ethernet: Link/Act
Steady green light indicates the unit is powered on. Lights steady green during Power on Self-Test (POST). Once the connection
status has been settled, the light will blink green. A system failure will be represented by a solid green light or the light going dark.
Steady green light indicates a valid ADSL connection. This will light after the ADSL negotiation process has been settled. Blinking green light indicates activity on the WAN interface. A solid green light will indicate a valid link on startup. This light will blink when there is activity currently passing through the Ethernet port.
17
DSL-524T ADSL Router Manual
Rear Panel
Connect the AC power adapter cord and network cables on the rear panel. The power switch and reset button are also located on the back of the device. Connect the antennas to the antenna posts.
All cable connections to the Router are made at the rear panel. The power switch and factory reset button is located here as well.
connect ADSL
ADSL port,
cable here
Factory reset
button
Ethernet port,
connect
Ethernet cable
Power cord
connects
here
18
DSL-524T ADSL Router Manual
2
Hardware Installation
The DSL-524T functions on two separate networks, as an Ethernet LAN and as an ADSL WAN. When deciding where to put the Router, the user must take into account the fact that it is connected to these three networks with three types of media. Ethernet cables connect the Router to computers and network devices, and the ADSL line connects it to a wall socket. In addition, the device must be near an AC outlet for power. How to accommodate these wired connections is often not a complicated matter, however, the added dimension of wireless communication does complicate the decision of Router placement.
Location
The Router can be placed on a shelf or desktop and ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.
Network Connection
Complete the connection to the network through the ADSL port and the Ethernet port on the back of the Router.
Connect ADSL Line
Use the ADSL cable included with the Router to connect it to a telephone wall socket. Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Router and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions included with the device or given to you by your service provider. The ADSL connection represents the WAN interface. It is the physical link to the ISP’s network backbone and ultimately to the Internet.
Connect Router to Ethernet
The Router may be connected to any 10/100BASE-TX Ethernet LAN. Any connection to an Ethernet concentrating device such as a switch or hub must operate at a speed of 10/100 Mbps only. When connecting the Router to any Ethernet device that is capable of operating at speeds higher than 10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting port. Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 port on the Router is a crossed port (MDI-X). Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. When connecting the Router directly to a PC or server use a normal straight-through cable. You should use a crossed cable when connecting the Router to a normal (MDI-X) port on a switch or hub. Use a normal straight-through cable when connecting it to an uplink (MDI-II) port on a hub or switch.
The rules governing Ethernet cable lengths apply to the LAN to Router connection. Be sure that the cable connecting the LAN to the Router does not exceed 100 meters.
Hub or Switch to Router Connection
Connect the Router to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable as shown in the diagram below:
19
p
If you wish to reserve the uplink
ort on the switch or hub for another device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable.
Computer to Router Connection
You can connect the Router directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided as shown in this diagram.
DSL-524T ADSL Router Manual
Power On Router
To power on the Router:
1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source.
2. You should see the Power LED indicator light up and remain lit. The Status LED should light solid green and begin to blink after a few seconds.
3. If you have the Router connected to your network you can look at the Ethernet Link/Act LED indicators to make sure they have valid connections. The Router will attempt to establish the ADSL connection, if the ADSL line is connected and the connection is properly configured this should light up after several seconds.
Factory Reset Button
The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on. Use a ballpoint or paperclip to push down the reset button. Remember that this will wipe out any settings stored in flash memory including IP settings. The factory default IP address of the Router is 192.168.1.1 and the subnet mask is 255.255.255.0.
20
DSL-524T ADSL Router Manual
3
Configuring the Router for the First Time
The first time you setup the Router it is recommended that you configure the WAN connection using a single computer making sure that both the computer and the Router are not connected to the LAN. Once the WAN connection is functioning properly you may continue to make changes to the Router configuration including the IP settings. This chapter is concerned with using your computer to configure the WAN connection. The following chapter describes the various menus used to configure and monitor the Router including how to change IP settings. This chapter discusses the steps to first establish the WAN connection. The remaining features, not directly concerned with establishing the initial connection, are explained in Chapter 4, Web-based Management. It is recommended that you install and configure the Router using one non-networked computer. This allows you to verify that the ADSL service is functioning and that you are able to communicate with the device. Once the initial ADSL connection is established, you can proceed to build an Ethernet LAN around the device or incorporate it into an existing LAN.
WAN Configuration Summary
1. Connect to the Router To configure the WAN connection used by the Router it is first
necessary to communicate with the Router through its management interface, which is HTML­based and can be accessed using a web browser. To access the management software your computer must be able to “see” the Router. Your computer can see the Router if it is in the same “neighborhood” or subnet as the Router. This is accomplished by making sure your computer has IP settings that place it in the same subnet as the Router. The easiest way to make sure your computer has the correct IP settings is to configure it to use the DHCP server of the computer. The next section describes how to change the IP configuration for a computer running a Windows operating system to be a DHCP client.
2. Configure the WAN Connection Once your are able to access the configuration software you
can proceed to change the settings required to establish the ADSL connection and connect to the service provider’s network. There are different methods used to establish the connection to the service provider’s network and ultimately to the Internet. You should know what Encapsulation and connection type you are required to use for your ADSL service. It is also possible that you must change the PVC settings used for the ADSL connection. Your service provider should provide all the information you need to configure the WAN connection.
Configuring IP Settings on Your Computer
In order to configure your system to receive IP settings from the Router it must first have the TCP/IP protocol installed. If you have an Ethernet port on your computer, it probably already has TCP/IP protocol installed. If you are using Windows XP the TCP/IP is enabled by default for standard installations. Below is an illustrated example of how to configure a Windows XP system to automatically obtain IP settings from the Router. Following this example is a step-by-step description of the procedures used on the other Windows operating systems to first check if the TCP/IP protocol has been installed; if it is not, instructions are provided for installing it. Once the protocol has been installed you can configure the system to receive IP settings from the Router. For computers running non-Windows operating systems, follow the instructions for your OS that configure the system to receive an IP address from the Router, that is, configure the system to be a DHCP client.
21
DSL-524T ADSL Router Manual
Configure IP Settings
You must now enable your computer to access the Router’s configuration software. To do this you will need to configure the IP settings on your computer. Follow these instructions to configure the IP settings for the operating system installed on your computer.
Windows XP
1. In the Windows task bar, click the Start button, and then click Control Panel.
2. Double-click the Network Connections icon.
3. In the LAN or High-Speed Internet window, right-click on icon corresponding to your network
interface card (NIC) and select Properties. (This icon may be labeled Local Area Connection).
4. The Local Area Connection dialog box displays with a list of currently installed network items.
5. Make sure that the check box to the left of the item labeled Internet Protocol TCP/IP is
checked, and click .
6. In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Use the
following IP address:
7. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
8. Click twice to confirm your changes, and close the Control Panel.
Windows 2000
First, check for the IP protocol and, if necessary, install it:
1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dial-up Connections icon.
3. In the Network and Dial-up Connections window, right-click the Local Area Connection icon,
and then select Properties.
4. The Local Area Connection Properties dialog box displays with a list of currently installed
network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step 3.
5. If Internet Protocol (TCP/IP) does not display as an installed component, click .
6. In the Select Network Component Type dialog box, select Protocol, and then click
7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click
8. You may be prompted to install files from your Windows 2000 installation CD or other media.
Follow the instructions to install the files.
9. If prompted, click
Next, configure IP information:
to restart your computer with the new settings.
1. In the Control Panel, double-click the Network and Dial-up Connections icon.
2. In Network and Dial-up Connections window, right-click the Local Area Connection icon, and
then select Properties.
3. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP), and
.
.
then click .
4. In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Use the
following IP address:
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
6. Click twice to confirm and save your changes, and then close the Control Panel.
22
DSL-524T ADSL Router Manual
Windows Me
1. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dial-up Connections icon.
3. In the Network and Dial-up Connections window, right-click on the Network icon, then select
Properties.
4. The Network Properties dialog box displays with a list of currently installed network
components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step 3.
5. If Internet Protocol (TCP/IP) does not display as an installed component, click .
6. In the Select Network Component Type dialog box, select Protocol, and then click .
7. Select Microsoft in the Manufacturers box.
8. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click .
9. You may be prompted to install files from your Windows Me installation CD or other media.
Follow the instructions to install the files.
10. If prompted, click to restart your computer with the new settings.
Next, configure the IP information:
1. In the Control Panel, double-click the Network and Dial-up Connections icon.
2. In Network and Dial-up Connections window, right-click the Network icon, and then select
Properties.
3. In the Network Properties dialog box, select TCP/IP, and then click .
4. In the TCP/IP Settings dialog box, click the Specify IP address option.
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
6. Click twice to confirm and save your changes, and then close the Control Panel.
Windows 95, Windows 98 and Windows 98SE
1. First, check for the IP protocol and, if necessary, install it:
2. In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.
3. Double-click the Network icon.
4. The Network dialog box displays with a list of currently installed network components. If the
list includes TCP/IP, and then the protocol has already been enabled. Skip to step 2.
5. If TCP/IP does not display as an installed component, click .
6. The Select Network Component Type dialog box displays.
7. Select Protocol, and then click .
8. The Select Network Protocol dialog box displays.
9. Click on Microsoft in the Manufacturers list box, and then click TCP/IP in the Network
Protocols list box.
10. Click to return to the Network dialog box, and then click again.
11. You may be prompted to install files from your Windows 95/98 installation CD. Follow the
instructions to install the files.
12. Click to restart the PC and complete the TCP/IP installation.
Next, configure the IP information:
1. Open the Control Panel window, and then click the Network icon.
2. Select the network component labeled TCP/IP, and then click .
23
DSL-524T ADSL Router Manual
3.
If you have multiple TCP/IP listings, select the listing associated with your network card or adapter.
4. In the TCP/IP Properties dialog box, click the IP Address tab.
5. Click the Specify an IP address option.
6. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0.
7. Click twice to confirm and save your changes.
8. You will be prompted to restart Windows.
9. Click .
Windows NT 4.0
1. First, check for the IP protocol and, if necessary, install it:
2. In the Windows NT task bar, click the Start button, point to Settings, and then click Control
Panel.
3. In the Control Panel window, double click the Network icon.
4. In the Network dialog box, click the Protocols tab.
5. The Protocols tab displays a list of currently installed network protocols. If the list includes
TCP/IP, then the protocol has already been enabled. Skip to step 3.
6. If TCP/IP does not display as an installed component, click .
7. In the Select Network Protocol dialog box, select TCP/IP, and then click .
8. You may be prompted to install files from your Windows NT installation CD or other media.
Follow the instructions to install the files.
9. After all files are installed, a window displays to inform you that a TCP/IP service called DHCP
can be set up to dynamically assign IP information.
10. Click to continue, and then click if prompted to restart your computer.
Next, configure the IP information:
1. Open the Control Panel window, and then double-click the Network icon.
2. In the Network dialog box, click the Protocols tab.
3. In the Protocols tab, select TCP/IP, and then click
.
4. In the Microsoft TCP/IP Properties dialog box, click the Specify an IP address option.
5. Type in IP settings as follows, IP address: 192.168.1.2 and Subnet mask: 255.255.255.0. Click
twice to confirm and save your changes, and then close the Control Panel.
Accessing the Configuration Manager
Now that your computer’s IP settings allow it to communicate with the Router, you can access the configuration software.
Note: Be sure that the web browser on your computer is not configured to use a proxy server in the Internet settings. In Windows Internet Explorer, you can check if a proxy server is enabled using the following procedure:
1. In Windows, click on the Start button, go to Settings and choose Control Panel.
2. In the Control Panel window, double-click on the Internet Options icon.
3. Click the Connections tab and click on the LAN Settings button.
4. Verify that the “Use proxy server” option is NOT checked. If it is checked, click in the checked box to deselect the option and click OK.
Alternatively you can access this Internet Options menu using the Tools pull-down menu in Internet Explorer.
24
DSL-524T ADSL Router Manual
To use the web-based management software, launch a suitable web browser and direct it to the IP address of the Router. Type in http:// followed by the default IP address, 192.168.1.1 in the address bar of the browser. The URL in the address bar should read: http://192.168.1.1. Once entered, the user will be prompted to enter the username and password to access the Configuration Manager, as show below. A new window will appear and you will be prompted for a user name and password to access the web-based manager. Use the default user name “admin” and password “admin” for first time setup. You should change the web-based manager access user name and password once you have verified that a connection can be established. The user name and password allows any PC within the same subnet as the Router to access the web-based manger.
NOTE: Do not confuse the user name and password used to access the web-based manager with the ADSL account user name and password needed for PPP connections to access the service provider’s network.
Figure 3-1. Enter Network Password dialog box.
Configure the Router with the Configuration Wizard
The first page that appears after you successfully login displays information about the Router’s Setup Wizard. Tabs across the top of the screen show other available menus: Home, Advanced, Tools, Status, and Help.
25
DSL-524T ADSL Router Manual
Figure 3-2. Home – Setup
When the Router is used to provide Internet access it actually must first access your service provider’s network, that is, it must communicate with computers and other modems owned by your service provider. These computers and modems then provide access to the Internet. The Router must be configured to communicate with the systems that give it access to the larger network. The quickest way for you to connect to the Internet is by using the Setup Wizard. Click the Run Wizard button the following window will appear:
26
DSL-524T ADSL Router Manual
p
The Setup window has four options listed, which will run through in the order given. Each step will be explained in detail. Click Next to access Step 1. You may click Back during the Setup procedure to return to the previous screen in the Setup Wizard, or Exit to exit the Setup Wizard at any time during the
rocedure.
Figure 3-3. Opening Setup window
Step 1: Choose Your Time Zone
In Step1, you must choose the time zone that best corresponds to the area you are living in by using the pull down menu. Choose the appropriate setting and click Next to go on to Step 2.
Figure 3-4. Choose Time Zone window
27
DSL-524T ADSL Router Manual
Step 2: Setting the ADSL Connection
Step 2 involves choosing the correct connection type mode for your modem. There are different methods or protocols used to make this communication possible, and both ends of the communication (you and your ISP) must agree on what method to use and how to set up the connection. This is what you want to configure the Router to do, to agree with the service provider’s equipment and negotiate the terms of the connection using a language or protocol that both sides understand. This window offers six connection types for the user to choose from. The choice will depend on information provided to you by your ISP. Options available on the DSL­524T are Dynamic IP Address, Static IP
Address, PPPoE/PPPoA and Bridge Mode. Simply click the corresponding radio
button and click Next to go on to the configuration window for that choice.
Figure 3-5. Set Internet Connection Type window
Step 2.1: Bridge Mode
Bridge Mode is for users who have software
on their computer or other network device to accept the connection from your ISP. You may change the PVC (Permanent Virtual Channel) settings, which are defined by two numbers, the VPI (Virtual Path Indicator) and the VCI (Virtual Channel Indicator). These two values should be provided to you by your ISP. In most cases, the default settings are correct and need not be altered. The second setting is the Connection Type, selected by using the pull-down menu. The two choices available to the user here are 1483 Bridged IP LLC and 1483 Bridged IP Vc-Mux, and this correct choice should also be provided to you by your ISP. After setting the values listed, click the Next button to go to Step 3 of the Configuration Wizard.
Figure 3-6. Set 1483 Bridged IP LLC
28
DSL-524T ADSL Router Manual
Step 3: Restart
In the following window, the user must restart the system to save the settings implemented, or go back to choose another option to configure.
29
DSL-524T ADSL Router Manual
Step 2.2: Static IP Address
The following window is used to set the Static IP mode for the Router. A Static IP address is used whenever a known static IP is assigned. The accompanying information such as the Subnet mask, ISP Gateway Address and DNS servers should also be specified in order to be able to connect. These are the servers would enable you to have access to other web servers. Valid IP addresses range from
1.0.0.1 to 255.255.255.255. To configure the connection for Static, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. After setting the values listed, click the Next button to go to Step 3 of the Configuration Wizard.
Figure 3-7. Set RFC2684 Bridged Static IP window
VPI/VCI
If you are told to change the VPI or VCI values, type in the values given to you by your service provider. Many users will be able to use the default settings.
IP Address Subnet Mask ISP Gateway
Address Primary DNS
Address
Secondary DNS Address
Connection Type
Enter the IP address based on the information provided to you by your ISP. Enter the Subnet Mask based on the information provided to you by your ISP. Enter the Default Gateway based on the information provided to you by your ISP.
This entry is for the IP address of your primary domain name server, which should also be provided to you by your ISP. The router will first try the Primary DNS Address to resolve a website’s URL IP address. If this IP address fails, the router will then try the Secondary DNS Address.
The IP address of the secondary domain name server will be used to resolve a website’s URL IP address if the Primary DNS Address fails. The information in this field should also be provided by your ISP.
There are four Connection Types set in the router to be chosen by using the pull down menu and they are 1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP LLC, 1483 Routed IP VC-Mux and IPoA. The correct choice should be told to you by your ISP.
30
Loading...
+ 77 hidden pages