DigiTech XP300 User Manual
XP-300
Owner’s
Guide
A Harman International Company
Visit Digitech on the World Wide Web at http://www.digitech.com
SAFETY HINTS:
WATER AND MOISTURE: Appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is
not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace with only same type fuse. Refer to replacement text on the unit
for correct fuse type.
W
ARRANTY:
1. The warranty card must be mailed within ten days after purchase date to validate this warranty.
2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under
normal use and service.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a
period of one year. A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be
liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design or make additions to or improvements upon this product without incurring any obligation to install the same on products previously manufactured.
6. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person
to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be
liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond
their control.
C
C
ongratulations, and thank you for your purchase of the Digitech XP-300 Space Station. The XP-300
offers not one, not two, but numerous effects in one compact heavy duty pedal chassis design. With the XP300, you get out of this world effects including: Resonators, Ring Modulators, Arpeggiator, AutoWhammy
Reverse Effects and more. In addition, the XP-300 also provides you with a Volume controller and a
Chromatic tuner. This owner’s guide is provided to get you up and going with the XP-300 and use it to its
full potential.
Front and Rear Panel Controls and Functions
1
. Signal LED - Indicates that signal is entering the XP-300.
2. Clip LED - Indicates that signal is clipping in the XP-300.
3. Status Display - The Status Display window shows the current information including: bypass, current
effect program number, and Chromatic Tuner information. When the XP-300 is in Program mode
(Factory or User), the display will either read:
1-40
(Factory) or
U1-U6
(User).
*Note- A complete listing of all Factory programs is located on the bottom panel of the XP-300.
4. Program UP/(Hold)DOWN Switch - Lets you select programs. Pressing once will move up through the
program menu. Press and hold and the XP-300 will move down through the program menu.
5. BYPASS/(Hold)TUNER Switch - Puts the unit into Bypass by pressing the footswitch once. To select the
Tuner, press and hold the footswitch until the display reads: tu, indicating that you are in Tuner mode.
6. Expression Pedal - Controls the selected effect or volume.
7. Input Level Control - Sets the amount of signal being sent into the unit. The ideal setting for the input
control of the XP-300 is to set the input level at a point where the Clip LED indicator occassionally
lights.
8. Input Jack - Connect instrument here using 1/4” guitar cord.
9. Left (Mono) Output - This is the Left (Mono) output of the XP-300. It can be used alone or together with
the Right output to produce stereo imaging effects.
10. Right Output - This is the Right output of the XP-300.
1
4
5
2
3
6
7 8
9 10
1211
Loading...