Digital Watchdog DWC-PB2M4TIR Quick User Guide

Safety Information

Important Safety Instructions

MEGApix® PANO 2.1MP 180° Camera

DWC-PB2M4TIR

Quick Start Guide

Ver. 1.0 / 2014.11

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the userwill be required to correct the interferenece at his own
expense.

To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that the plug is easily
accessible.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

:

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.

This exclamation point symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To prevent damage which may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may
cause abnormal heat generation or fire.

4. Securely plug the power cord into the power receptacle. Insecure connection may
cause fire.

5. When installing the camera, fasten it securely and firmly. A falling camera may cause
personal injury.

6. Do not place conductive objects (e.g. screw drivers, coins, metal things, etc.) or
containers filled with water on top of the camera. Doing so may cause personal injury
due to fire, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued
use in such a condition may cause fire or electric shock.

9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way.

10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock.

CAUTION

1. Do not drop objects on the product or apply strong shock to it. Keep away from a
location subject to excessive vibrationor magnetic interference.

2. Do not install in a location subject to high temperature low temperature or high
humidity. Doing so may cause fire or electric shock.

3. If you want to relocate the already installed product, be sure to turn o the power and
then move or reinstall it.

4. Remove the power plug from the outlet when then there is a lightning. Neglecting to
do so may cause fire or damage to the product.

5. Keep out of direct sunlight and heat radiation sources. It may cause fire.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the image sensor.

8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.

9. The Mains plug is used as a disconnect device and shall stay readily operable at any
time.

WARNING

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, or other

apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not t into
your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specied

by the manufacturer, or sold with the apparatus.

13. Unplug this apparatus when a cart is used. Use caution

when moving the cart/apparatus combination to avoid
injury from tip-over.

14. Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

Product & Accessories Part Name Installation

Please check if all the camera and accessories are included in the package.

Camera

Manual CDQuick Start Guide Template Sheet T-Wrench

Sunshield Sunshield ScrewsScrew & Plastic Anchor-4pcs 2nd BNC Output Cable

Cables

Sunshield

Cables

Ball Neck Bracket

Pan/Tilt stoper screw

Con Cap

Lens

Before installing your camera, read the following carefully.

1. The mounting surface must withold at least ve time the weight of the camera.

2. Do not let any cables get caught or the electric cver be damaged during installation.

SD Card Slot

Test Video OutputReset Button

1

Using the Mounting Template or the
camera itself, mark and drill the
mounting holes.

Pass cables through and connect the

2

cables respectively. See the section
‘Cabling’ for more information.

3

Secure the camera to the wall/ceiling
using the provided screws.

Before securing the camera to the mounting
surface, slightly loosen the Pan/Tilt stoper screw.

4

Using the secondary BNC output,
check the camera’s view and adjust as
needed during installation.

5

Attach the Sunsheild to the bottom case
by using Sunshield Screws.

Reset to the Factory Default

Press the reset button for 5 seconds to
return the camera’s settings to their
factory default.

Warning:

Pressing the ‘Reset’ button will result
in loss of all setting data. If needed,
make a note for further installation.

TEL: [phone]
www.Digital-Watchdog.com / [e-mail]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST

20150316

Cabling

IP Installer

Two Options

Use a PoE-enabled switch to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for
power transmission.

1. Using a PoE-Enabled Switch

The Camera is PoE-compliant, allowing
transmission of power and data via a
single Ethernet cable.
PoE eliminates the need for the dierent
cables used to power, record, or control
the camera.

to connect the camera

Follow the illustration below

to a PoE-enabled

2. Using a Non-PoE Switch

If a PoE-enabled switch is not used, use
a power adaptor for power transmission

and non-PoE switch for data transmission.

Follow the illustrations below to connect

the camera without a PoE-enabled Switch.

switch using an Ethernet cable.

switch using an Ethernet cable.

Ethernet Cable

Ethernet Cable

Power

1

Power

1

Power Connection

Please, check the voltage and current
capacity of rated power carefully.

Rate

Power

DC 12V 6W (IR Off)

2

Network Connection

Current

Consumption

19W (IR On)

IEEE 802.3at

PoE+ /

High Power PoE

Connect the crossover cable into the
RJ-45 port.

PoE

4

3

Audio Output

2

Network
Connection

3

Audio Output

Connect the ‘Audio Out’ cable of the
camera to a device such as a speaker.

4

Audio Input

Connect the ‘Audio In’ cable of the
camera to a device such as a
microphone.

Audio Input

White : DIN+
Yellow : DIN­Black : DOUT­Red : DOUT+

5

Alarm Output

Connects to alarm lights, siren or
lamps and is activated according to
the Setup Menu settings.

Connect the relay output device’s
cables to the red and black lines of the
Alarm Cables.

6

Alarm Input

5

Alarm Output

6

Alarm Input/Sensor
Connect the sensor/alarm input
device’s cables to the white and yellow
lines of the Alarm Cables.

2

3

4

1. Run IP Installer

1

Run the CD inclued with the camera
and install the IP installer in S/W folder.

2

Click on Network Adaptor selection Menu
(NIC).

3

Select the network the camera is
connected to and click ‘Search’. Allow
up to 5 seconds for the IP Installer to
nd the camera on the network.

4

Select a camera from the list by
checking the box next to the camera’s
name.

5

The camera’s information will appear
under Device Info.

5

7

8

9

11

12

6

If necessary you can change the
camera’s network type.

Select DHCP if the internet service is
dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.

Select STATIC if the camera’s IP address is
received from a network
camera is set to STATIC, manually enter the
camera’s IP address, subnet mask, Gateway
and DNS information.

If the camera is set to STATIC, please contact
your Network Administrator or internet
service provider for more information.

administrator. If the

6

10

10

7

The camera’s IP information will be
displayed in the IP section. If the
camera is set to STATIC, you can
manually enter that information in the
corresponding elds.

Default TCP/IP information

- IP: 192.168.1.80

- Subnet Mask: 255.255.255.0

- Gateway: 192.168.1.1

- DNS : 168.126.63.1

8

Change the camera’s communication
ports as necessary.

A ‘Port Forwarding’ has to be set in your
network’s router for external access to the
camera.

Refer to the router’s manual for ‘Port
Forwarding’ setup.

An additional change of HTTPS, RTSP port
can be done at the camera’s Setup Menu
under Web Viewer >Admin page.

9

Input ID and PW of the camera for
authentication.

It is recommended to change the camera’s
ID and PW for security reason.
To change the camera’s username and
password, Go to “Web viewer>Admin
page>System>Users”.
The ID and PW will be set to default value

Default ID / PW : admin / admin

TEL: [phone]
www.Digital-Watchdog.com / [e-mail]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST

Make sure to click ‘Save’ to save
any changed values.

An “Apply” message will pop-up when
settings are successfully changed, or an
error message will pop-up when changes
were not saved.

11

To reboot or reset (except network setting)
the camera.

Select a camera (multiple camera can be

selected) > Input ID and PW > Click ‘Reboot

or Factory Reset’.

12

Delete an Active-X le for a camera’s
Web Viewer.

Please re-install the Active-X after deleting
previous Active-X.
options
depending on the IE version.
Note that all other IE windows will be closed
when uninstalling Active-X.

To access the camera’s Web Viewer, double­click on any of the cameras in the IP Installer.
The camera’s Web Viewer will open in an IE
window.

Input the camera’s ID and PW.

Install all ActiveX files requests.

Changing the security

of your IE may be necessary

20141103

Web Viewer Screen

Web viewer is optimized with Windows
XP or above and Internet Explorer browser.

1

Live video display. This area displays
live video stream from the camera.

2

Resolution. The resolution information
of the video currently in display.

3

SD Card Search. Searching or Playing
images stored in the SD Card.

4

Setup popup button. Click it to open
the camera’s setup page. This allows
you to setup the camera’s Video,
Network, Events, System etc.

5

Control tab button. Click the button to
extend the panel for full control of the
web-viewer’s function.

2 31

5

7

9

PTZ control button. Click the button to

6

extend the panel to control the camera’s
Pan, Zoom, Preset, Tours etc.

7

Full screen button. Click the button to
extend the display to full screen. Press
‘Esc’ or ‘Enter’ to return to normal mode.

8

Camera Setup button. Click the button
to open the Setup page to setup the
camera’s image settings such as lens,
white balance, auto exposure, BLC etc.

9

Event alert icon. If Alarm in and Motion
detection are detected, below icons will
appear.

<Alarm Input> <Motion Detection>

Disposal of Old Appliance

1. When this crossed-out wheel bin symbol is attached to a product it means the

4

6

8

product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately form the
municipal waste stream in accordance to laws designated by the government or the
local authorities.

3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact
your city oce, waste disposal service or the shop where you purchased the product.