Digital Watchdog DWC-MV950TIR User Manual

PREPARATION

INSTALLATION

MV950TIR

IP 5MP Vandal Dome Camera

Quick Setup Guide

The following items are included with the MV950TIR Camera

MV950TIR

Quick Start

IP 5MP Vandal Dome Camera

Guide

L-Wrench

2nd Video

Output Adapter

2x Drying

Agent- Silica

Gel Packet

(Manual &

Software)

Waterproof Acessories

& Power

Outlet Adaptor

DC Cable

Adapter

Mounting Template

3x Mounting

Screws and Wall

Anchors

Vandal Dome Camera

Mounting the Camera

Using the camera base or the mounting

template, mark and drill 3 pilot holes and insert anchors. Use screws to affix the camera base to the ceiling or wall.

Adjust the camera lens using tilt & swivel controls as needed. Use the Zoom and Focus hadles to adjust the camera’s lens.

Pull all necessary wires through and use

the diagram on page 2 of this QSG to make all proper cable connections.

After adjusting lens, remove a drying agent pack from one of the silver packages stored inside the accessories package*. Remove the sticker from the drying agent pack and insert in the front under the lens as shown in the image*.

BNC 2nd Video Output

The camera can provide video out via BNC cable. The BNC cable provided has a 2 pin plug. When connecting the BNC cable for SDTV video out, connect the BNC cable to pin 3 & 4 as shown in the image above.

IR Sync. Function

If using an external IR trigger, then connect the external IR device to the camera’s 2-pin IR Sync port.

Additional Cabling Connections

1x RJ45 Netowkr Port

1x RJ45 Connector 2x Sensor Input

Audio In/ Out

DC Power

Resetting the Camera

Pressing the reset button on the camera’s control board, while the camera is on, for six (6) seconds will initialize

all environmental variables to factory default. Previous setup for IP default, time, etc. will be reversed to its

factory default values. The following are the default network settings:

IP Mode DHCP

IP Address 192.168.1.2

Subnet Mask 255.255.255.0

Gateway 192.168.1.1

RTP Video Port 6002

HTTP Port 80

RTSP Port 554

Frequent use may cause a System Error

TEL: (866) 446-3595 www.Digital-Watchdog.com / technicalsupport@dwcc.tv Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST

08 21 20 13

Reset Switch

Thank you for purchasing Digital Watchdog’s MEApix IP Vandal Dome Camera. Before installing the camera, please verify your model and read this guide carefully.

Network Connection

There are two options.*

Using a PoE-Enabled Switch

The MEGAPIX Camera is PoE-compliant, allowing transmission of power and data via a single ethernet cable. Follow the illustrations below to connect the camera to a PoE-enabled switch using an ethernet cable.

Using a Non-PoE Switch

If a PoE-enabled switch is not used, use a power adaptor to connect the MEGAPIX Camera to a Non-PoE switch.

The drying agent pack should be replaced each time the camera is opened (front or back). Be sure to complete all work before inserting drying agent pack & replacing the cover.

3 5 7

Drying agent packs will become ineffective if exposed to open air for more than 10 minutes.

Mounting the Camera

Water Resistant Accessories

Prepare conduit, and slide necessary cables through tubing. After subsequent cabling is done, insert tubing into A and screw C on to A.

Wall Mount Bracket

Run all necessary cables through the bracket before securing the bracket to the wall.

Mount the Wall Mount to the wall using the mounting template or the bracket itself.

Secure the camera housing to bracket and secure by tightening the screws; be sure to pass cabling into hole in the camera housing.

Camera Specifications

IMAGE

Image Sensor 1/2.5” 5MP CMOS Sensor

Total Pixels 2592 (H) X 1920 (V)

Minimum Scene Illumination 0.0 Lux

LENS

Focal Length 3.4~10mm

Lens Type Varifocal/ DC- Iris IR Distance 50ft Range IR Angle of View Horizontal: 40 (wide) - 25 (tele)

AUDIO

Compression and Sampling Rate G.711/ G.726/ AAC Input / Output Built-in Microphone, 1x Line In and 1x Line Out

NETWORK

LAN 802.3af Compliance Video Compression Type H.264 H.264, MPEG4, MJPEG Resolution 10fps @ 2560x1920 (5MP) 10fps@2592x1920(5MP) / 20fps@2048x1536(3MP) / 30fps@1920 x1080(2MP)

Frame Rate Up to 10fps Up to 30fps based on Resolution

Streaming Capability Dual-Stream at Different Rates and Resolutions

IP IPv4, IPv6

Protocol TCP/IP, HTTP, DHCP, PPPoE, HTTPS, ICMP, ARP, RTSP,

NTP, UDP, NTP, SMTP, RTP, RTCP, 3GPP, SAMBA (NAS) Maximum User Access 10 Users ONVIF Conformance Yes , Profile S

Web Viewer OS: Windows XP / Vista / 7, MAC OS

Browser: I.E. 8 or Higher, Chrome, Firefox, Safari

Video Management Software DW Spectrum

Memory Slot Micro SDHC Card (4GB-32GB) Card Not Included*

ENVIRONMENTAL

Operating Temperature/ Humidity -25

Operating Humidity Less than 80% (Non-Condensing) Storage Temperature -29oC ~ 55oC (-20oF ~ 131oF) IP Rating IP66 (Protects against dust and high pressure water) Other Certifications CE, FCC, RoHS

ELECTRICAL

Power Requirement DC 8~25V, AC 24V, PoE (IEEE802.3af Class 3)

Power Consumption Max 8.9W, 600mA

MECHANICAL

Material Aluminum Housing Dimensions 152 X 98 mm (5.98 X 3.85 in)

6 8

Weight 2.42 lbs

DW Optimized Firmware Full Firmware Option

C ~ 55oC (-13oF ~ 131oF)

MEGAPIX CAMERA SETUP

Installing DWScan

DWScan searches for all the available supported network devices on

your local area network.

Install DWScan to find the MB950TIR Cameras on the local network. The DWScan software can be found on the included CD. Run DWScan and install onto your

PC.

When setup is complete, launch the DWScan software.

To find your MB950TIR cameras, click the Scan button.

You can use the DWScan software to adjust the camera’s IP Address and Network Settings

To change the camera’s Network Settings, press the Change Settings button.

Accessing the Camera

Web Viewer Interface

Video Display Size

Video Controllers

Alarm Indicators

Video Resolution & FPS Information

Audio Controllers

Lens Controllers

PTZ Virtual Controller Stream Selection

Live/ Setup/ Client Setup Access

11 13

Relay Input and Alarm Output Control

Remote Video Monitoring

Use the camera’s control bar and status indicators to manage the camera’s relay and alarm inputs and outputs.

- Digital IN Alert will blink to notify you when a relay connected to the camera is triggered.

- Use the Digital Out button to start/ stop any alarm output connected to the camera. Refer to the full manual for more information on how to setup relay input and output control in the camera.

Instant Recording

Instantly record live video to your local drive.

User1

To Setup Instant Recording

Make sure the directory path is setup. To do so go to Client Settings at the top right-hand corner of the screen and press ‘Select Path’

To Start and Stop Instant Recording

To Start, press the icon on the control menu bar. A window will appear to notify you instant recording has begun. The button will blink red indicating you are currently recording video. To Stop, press the button again. The video file will appear in the designated directory path.

Accessing the Camera Using its Web Browser

For advanced setup and camera view, access the camera using its

built-in web server.

When accessing an IP camera using the web interface for the first time (or when the IP address changes), some configuration for ActiveX controls are required.

1. Open an IE browser

2. Type in the IP address in the URL: http://<IP ADDRESS> (e.g. http://10.1.21.53).

3. Default Username and Password: root/ pass.

4. Pop-up windows and messages for download/run Active X controls (examples below) will likely be displayed. Select Install or Run to all such messages. Click on the add-on message and choose Run Add-on.

5. Repeat the above until all ActiveX controls have been initiated. Once the process is complete, the Live View will be displayed in IE.

6. When all Active X files have been properly installed, the web viewer will display the camera’s live video and control center.

The web viewer can also be accessed via Firefox and Google Chrome if QuickTime player is installed.

Webviewer Specifications

Minimum Requirements for PC

CPU RAM HDD OS Resolution

TEL: (866) 446-3595 www.Digital-Watchdog.com / technicalsupport@dwcc.tv Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST

Intel P4 2.0GHz Dual Core

More than 1GB

200GB Required for Saving Clip Image

Microsoft Windows XP or Higher

Higher than 1024X768

Export Image

Not available in the DW Optimized Firmware

User1

1. Make sure the directory path has been setup. To do so: a. Go to Client Settings at the top right-hand corner of the screen. b. Press ‘Select Path’ to select the directory where all exported images will be saved to. Settings will be saved automatically.

c. Click on the ‘Live View’ link at the top right-hand corner of the screen to return to the camera’s live display.

2. To export an image of the camera’s current live view, press the button at the top control bar. An image with time stamp will automatically be saved as a JPEG file.

Stream Setup and Selection

The MB950TIR supports multiple simultaneous streams (up to 4 different profiles). The Streams can be switched from the camera’s web viewer by selecting the corresponding stream from the drop down menu in the Stream Control option. The stream’s current resolution and framerate information will be displayed in the information section. To setup the different streams: a. Go to ‘Setup’ at the top right-hand corner of the screen. The setup menu will appear. b. Go to Video/Audio > Video Settings c. Select the number of profiles you would like to assign the camera. d. All selected profiles will appear under the Quality Setting Section. Here you can modify each streams’ resolution, codec, bitrate, and max framerate. e. Press ‘Save’ to save all settings.

SD Card Installation & Setup

The MB950TIR supports local storage recording as well as remote

FTP and NAS recording. All recording settings can be done by pressing

‘Setup’ in the upper right-hand corner of the screen.