Digital Watchdog DWC-MTT4Wi36, DWC-MTT4Wi6 Quick Start Guide
DW C-M TT4Wi2 8
DWC-MTT4Wi36
DWC-MTT4Wi6
Quick Start Guide Quick Start Guide
Template
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must bear three times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover
to be damaged. This may cause a breakdown or fire.
3. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Sheet
1
3
a
4
Ethernet
Cable
Default Login Information
Username: admin Passwo rd: admin
WHAT’S IN THE BOX
QSG Manu al 1 Set
Mounting
Template
Waterproof
Cap
Rubber Plug 1 Set
NOTE: Download All Your Support M aterials a nd Tools in One Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search yo ur product by entering the part number in the ‘Search by Product’ search
bar. Results for applicable par t numbers will popu late automatically based on the
part number you enter.
3. Click ‘Search’. All supported mater ials, incl uding man uals, Quick Start G uides
(QSG), soft ware and fir mware will appear in the results.
Attention: This document is intended to serve as a quick refe rence for initial
set-up. It is recommended that the user r ead the entire instruction manual for
complete and proper installation and usage.
Tapping
Screws PA
4x35 – 4pcs
Plastic Plugs
1 Set
– 4pcs
1 Set Tor x Wre nch 1 Set
1 Set
1 Set
4. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission
and use a power adapter to power the camera.
Power Requirements Power Consumption
DC 12V
POE IEEE 802.3af
LED On: 5W, 418mA
LED Off: 2.5W, 208mA
STEP 3 – INSTALLING THE CAMERA
5. To use the camera’s water proof wiring:
(1). Install the LAN cable into .
b
(2). will be assembled to with a 1/4 turn.
(3). Thread tightly to .
c
NOTE: To ensure moisture seal, make sure the o-ring is in place between
a
b
and . In extreme environments use of an outdoor rated
sealer is recommended.
NOTE: When using the waterproof cap, crimp the RJ45 connector after
passing the cable through the waterproof cap.
6. Adjust the camera to obtain an optimum angle by loosening the lock screws.
Tighten the lock screws after you finish adjusting the view angle of the
camera.
7. Remove the protection film softly to complete the installation.
a
a
b
b
4
2
4
Rubber
Plug
5
b
a
6
Lock Screw
Power
Ethernet
Cable
c
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Quick Start Guide
STEP 4 – DW IP FINDER
™
Use the DW IP Finder™ software to scan the network and detect all MEGApix®
cameras, set the camera’s network settings or access the camera’s web client.
NOTE: DW IP Finder™ v4.3.7 or later is required.
Camera Name,
Model, IP Address,
and MAC Address
Firmware Upgrade
Search for Cameras
Filter Search Results
Cam era’s
Network Settings
Vie w Cam era’s
Thumbnail View
Camera Uptime
Cam era’s Firmware
Open Camera’s IP
Conguration Screen
Network Setup
1. Go to: http://www.digital-watchdog.com
2. Search for ‘IP Finder’ on the quick search bar at the top of the page.
3. The latest IP Finder software will appear in the search results. Click on the
link to download the file to your computer.
4. The software will scan your network for all suppor ted cameras and display
the results in the table. Allow up to 5 seconds for the IP Finder to find the
camera on the network.
5. Select a camera from the list by double-clicking on the camera’s image
or clicking on the ‘Click’ button under the IP Conf. column. The camera’s
network information will appear. If necessary, you can adjust the camera’s
network type.
6. The camera’s default network information is:
Default TCP/IP information
• IP: DHCP
7. To view the camera’s web viewer, click on ‘View Camera Website’.
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
8. To save the changes made to the camera’s settings, input the ID and PW of
the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed, press
the ‘Reboot’ button. The camera will cycle power and will appear back in the
search results once the reboot is complete.
Default ID / PW : admin / admin
STEP 5 – WEB VIEWER
NOTE: This camera’s web client must be accessed via Internet Explorer
web browser only.
*
The GUI d isplay may differ by ca mera models.
Once the camera’s network settings have been setup properly, you can access
the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
™
1. Find the camera using the DW IP Finder
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will open up
in your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the first time, install the ActiveX player
for web files in order to view video from the camera.
.
Select DHCP if the internet ser vice is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
*
NOTE: Some Menu options may not be available based on the camera
model. See the full manual for more information.
Rev Date: 04/17
Specifications and pricing are subject to change without notice.
Copyright © Digit al Watchdog. A ll rights reserve d.
Loading...