Digital Watchdog DWC-MPTZ830XW Quick Start Guide

Quick Start GuideQuick Start Guide

DWC-MP TZ336XW DWC-MP TZ830XW

Default Login Information

Username: admin Password: admin

WHAT’S IN THE BOX

QSG 1 Adapter ring 1

PoE inj ector 1

Safety wire 1

Power cord 1

ACCESSORIES REQUIRED TO INSTALL THE CAMERA (SOLD SEPARATELY)

Wall mount bracket:

DWC-P33 6WMW

DWC-P30 CNMW (must be purchased with DWC- P336WMW)

NOTE: Mounting a ccessories are required and sold separately.

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the
‘Search by Product’ sea rch bar. Result s for applicable
part numbers will populate automatically based o n the
part number you enter.

3. Click ‘Search’. All supporte d materials, including manuals
and quick start guide (QSGs) will appear in the results.

Ceiling mount bracket:

DWC-P33 6CMW

For corn er and p ole mo unt bra cket:

Waterproof
cap

2P, 5P
screw-type
connectors

Parapet mount bracket:

DWC-P336PARAMW

1 set

1 set

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the camera weight.

2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.

3. For the installation process, remove the protection film and the tape
from attached the dome camera.

4. A silicone rubber sealant must be applied to seal the housing to
secure waterproofing.

Seal using silicone

Twi s t

Start Point
(Long Indicator)

Set Point
(Long Indicator)

rubber around the circle

5. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.

STEP 2 – POWERING THE CAMERA

Pass the wires through the mount bracket and make all necessary
connections.

1. NETWORK CONNECTIONS – If you are using the PoE injector
included, connect the camera using an Ethernet cable for both data
and power.

2. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.

Power requirements Power consumption

UPoE injector, 12VDC
(PoE injector included, adapter not
included)

1

PoE: 28W, 500mA
12VDC: 28W, 2.3A

2

STEP 3 – INSTALLING THE CAMERA

1. Using the mounting template or the mounting accessory itself, mark and drill
the necessary holes in the mounting surface.

2. Pull all cables through the mounting accessory. See STEP 4.

3. Attach the wall mounting bracket to the mounting surface using plastic anchors
and M8x35 screws.
For a ceiling mounting bracket installation, use the plastic anchors to secure it to
the mounting surface.

4. Wind both of the pipe ends thread with Teflon tape about 20 times for sealing.
Use a silicone rubber sealant to seal the area where the mounting bracket and
the pipe meet.

5. Place a bead of silicone sealant around the mounting bracket’s mounting flange,
press it to the surface and line up the flange hole with drilled holes.

6. Open the access plate on the mounting accessory and pull out the cables
through the rectangular access hole.

7. Attach the 1.5” adapter to the mounting bracket and fix it using the set screw.

8. Attach the camera’s safety wire to the mounting bracket and organize the
cables.

9. Connect all the cables to the camera. See STEP 4. Close the access plate o the
mounting bracket.

10. Connect the camera to the mounting bracket by turning it clockwise into the
adapter, and fix it using the set screw of the adapter.

Installing the camera using a wall mount

Plasti c anchors (4x)

Tapping screws 8x35 (4x)

Mounting bra cket (1 x sold
separ ately) PF 1 .5 inch

Set screw (1x)

Adapter PT 1. 5 inch ( 1x)

Set screw (1x)

Safety wire

Access plate

Machine screws M3x5 (2x)

Installing the camera using a ceiling mount

Safet y wire (1x)

Plasti c anchors (3x)

Mounting bra cket (1 x
sold separately)

Set screws (2x)

Locking nut (1x)

Tapping screws 6x35 (3x)

Socket (1 x)

Machine screw M5x6 (1x)

Pipe (1x)

Pipe so cket PF 1 .5 incg (1x)

Set screws (3x)

Adapter PT 1. 5 inch ( 1x)

Set screw (1x)

Attention: This document is intended to serve as a quick reference for the initial
set up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.

Tel: [phone]

Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday

digital-watchdog.com

Ethernet
Cable

Power

Ethernet
Cable

Quick Start Guide

STEP 3 – MANAGING THE SD CARD STEP 6 – NETWORK ACCESS (WEB)

Users can insert and remove a micro-SD card as shown in the
following picture.

STEP 5 – DW® IP FINDER

Use the DW® IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Thumbnail view

Select network to scan

Filter device type to scan

Scan devices

Reset button

Show/hide thumbnail view

Refresh thumbnail view

™

1. Enter the camera’s IP address in a web browser (IE is
recommended). The

2. In the welcome screen, select whether to view a live image from the

Firmware version

Camera’s uptime

camera, search recorded data on the SD card or enter the camera’s
settings.

3. If you are entering the camera’s settings, enter the user name and
password (default admin/admin).

Open Device
configuration
settings

Bulk IP assignment

Micro -SD card slot

1. Open the micro-SD card cover under the camera’s lens.

2. Insert or remove the micro-SD card as needed.

3. Tightly close the micro-SD card cover to ensure it is waterproof.

Resetting the camera: To reset the camera, use the tip of a paper
clip or a pencil and press the reset button located under the
camera’s lens module. See the diagram above for it’s location.
Pressing the button for five (5) seconds will initiate a camera-wide
reset of all the settings, including network settings.

STEP 4 – CABLING

Use the diagram below to connect external devices such as audio
and alarm inputs and outputs to the camera.

No Connector Wire Color Description

1 Power jack Black Camera power (12VDC)
2 RJ-45 Black Ethernet
3 RCA jack Black Audio input
4 RCA jack Gray Audio output

5 5-pi n cable

6 2-pin c able

Yel lo w Alarm input 1
White Alarm input 2
Violet Alarm input 3
Brown Alarm input 4

Gray GND

Red Alarm output

Black GND

1

2

3

4

5

6

Firmware upgrade

Network setup

1. To install the DW® IP Finder™, go to

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page
and press Enter.

3. Click on the DW® IP Finder™ from the search result and go to the
Software tab. Click on the download icon to download the DW®

IP Finder™ installation file.

4. Run the installation file and follow the wizard to install the DW®
IP Finder™. Open the DW® IP Finder™ and click ‘Scan Devices’. It

will scan the selected network for all supported devices and list
the results in the table. During the scan, the DW® logo will

turn gray.

Selec t DHCP if the internet service is dynamic IP. This will allow the
camera to receive its IP address from the DH CP server.

Selec t “Static” to manually enter the camera’s IP address, (Sub)
Netmask, Gateway and DNS information.

The camera’s IP must be set to Static if connecting to DW Spectrum®

IPVMS. Contact your network administrator for more information.

Default TCP/IP information: DHCP

Device’s
information

5. Select a camera from the list by double-clicking on the
camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.

6. To access the camera’s web page, click on ‘View
Camera Website’.

7. To save the changes made to the
camera’s setting, input the username
and password of the camera and click
Apply. Click “Scan Devices” from the
main screen again to display the
updated information.

‘Port forwarding’ has to be set in your
network’s router for external access
to the camera.

Default ID / PW: admin / admin

*NOTE: For security purposes, it is highly

recommended to change your
password after initial setup.

STEP 7 – LIVE VIEW

1

5 6 7 8 9 10 11 12 13

1. Select Stream 1 (H.264), Stream 2 (MJPEG), Stream 3 (H. 264)

2. Select resolution up to 1920x1080

3. Select network protocol between HTTP, TCP, and UDP

4. Call preset up to 256

5. Stop and start for live stream

6. Stream pause

7. S napshot

8. Zoom

9. Fullscreen

10. Manual trigger

11. Pop-up PTZ control panel

12. Speaker volume

13. Microphone control

NOTE: Please see the full product manual for web viewer setup,

functions and camera settings options.

Rev Date: 05/20

2 3 4

Speci fications an d pricing are subject to chang e witho ut notice.

Copyright © Digital Watch dog. A ll rights rese rved .

1110