Dewalt DWFP72155 User Manual

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

INSTRUCTION MANUAL
GUIDE D’UTILISATION

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.

MANUAL DE INSTRUCCIONES

DWFP72155
15 Gauge Precision Point™ “DA” Style Angle Finish Nailer
Cloueuse De Finition D'angle « DA » Precision Point™ De Calibre 15
Clavadora De Acabado Con Ángulo Estilo "DA" Con Punta De Precisión Calibre 15

BEFORE OPERATING THIS TOOL, CAREFULLY READ AND
UNDERSTAND ALL INSTRUCTIONS IN THE IMPORTANT
SAFETY INSTRUCTIONS SECTION.

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to these
symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY D

E

(1-800-433-9258)

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Important Safety Instructions

WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.

WARNING: This product contains chemicals known to the State

of California to cause cancer, and birth defects or other reproductive
harm. Wash hands after handling.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm such
as asbestos and lead in lead based paint.

• Actuating tool may result in flying
debris, collation material, or dust
which could harm operator’s eyes.

The operator and all those persons in the

general area should wear safety glasses
with permanently attached side shields.

Approved safety glasses are imprinted
with the characters “Z87.1”. It is the

employer’s responsibility to enforce the
use of eye protection equipment by the

tool operator and other people in the work

area. (Fig. A)

• Always wear appropriate personal
hearing and other protection during
use. Under some conditions and duration

of use, noise from this product may
contribute to hearing loss. (Fig. A)

• Use only clean, dry, regulated air.

Conden sation from an air compressor can

rust and damage the internal workings of

the tool. (Fig. B)

• Regulate air pressure. Use air
pressure compatible with ratings on

the nameplate of the tool. (Not to

exceed 120 psi, 8.3 bar) Do not connect

the tool to a compressor rated at over
200 psi. The tool operating pressure must

never exceed 200 psi even in the event of
regulator failure. (Fig. C)

1

FIG. A

FIG. B

FIG. C

FIG. D

English

• Only use air hose that is rated for a maximum working
pressure of at least 150 PSI (10.3 BAR) or 150% of the
maximum system pressure, which ever is greater. (Fig. D)

• Do not use bottled gases to power this
tool. Bottled compressed gases such as

FIG. E

oxygen, carbon dioxide, nitrogen, hydrogen,
propane, acetylene or air are not for use
with pneumatic tools. Never use

English

combustible gases or any other reactive
gas as a power source for this tool. Danger
of explosion and/or serious personal injury
may result. (Fig. E)

• Use couplings that relieve all pressure

FIG. F

from the tool when it is disconnected
from the power supply. Use hose

connectors that shut off air supply from
compressor when the tool is disconnected.
(Fig. F)

• Disconnect tool from air supply when
not in use. Always disconnect tool
from air supply and remove fasteners

FIG. G

from magazine before leaving the
area or passing the tool to another
operator. Do not carry tool to another
work area in which changing location
involves the use of scaffoldings, stairs,
ladders, and the like, with air supply
connected. Do not make adjustments,
remove magazine, perform maintenance or clear jammed
fasteners while connected to the air supply. If the contact trip is

adjusted when the tool is connected to the air supply and nails are
loaded, accidental discharge may occur. (Fig. G)

• Connect tool to air supply before loading fasteners, to
prevent a fastener from being fired during connection. The

tool driving mechanism may cycle when tool is connected to
the air supply. Do not load fasteners with trigger or contact trip

depressed, to prevent unintentional firing of a fastener.

• Do not remove, tamper with, or
otherwise cause the tool, trigger, or

FIG. H

contact trip to become inoperable.

Do not tape or tie trigger or contact trip in
the on position. Do not remove spring
from contact trip. Make daily inspections
for free movement of trigger and contact
trip. Uncontrolled discharge could result.

• Inspect tool before use. Do not
operate a tool if any portion of the tool,

FIG. I

trigger, or contact trip is inoperable,

disconnected, altered, or not working
properly. Leaking air, damaged parts

or missing parts should be repaired or
replaced before use. (Fig.H)

• Do not alter or modify the tool in any

way. (Fig. I)

• Always assume that the tool contains

FIG. J

fasteners.

• Do not point the tool at co-workers
or yourself at any time. No horseplay!

Work safe! Respect the tool as a working

implement. (Fig. J)

2

• Keep bystanders, children, and visitors away while operating
a power tool. Distractions can cause you to lose control. When

tool is not in use, it should be locked in a safe place, out of the
reach of children.

• Remove finger from trigger when
not driving fasteners. Never carry

FIG. K

tool with finger on trigger. Accidental
discharge could result. Using the trigger
lock-off will prevent accidental discharge.

• Do not overreach. Maintain proper
footing and balance at all times. Loss of
balance may cause cause personal injury.
(Fig. K)

• Make sure hose is free of obstructions

FIG. L

or snags. Entangled or snarled hoses
can cause loss of balance or footing.

• Use the tool only for its intended
use. Do not discharge fasteners into
open air, concrete, stone, extremely
hard woods, knots or any material
too hard for the fastener to penetrate.
Do not use the body of the tool or top
cap as a hammer. Discharged fasteners

FIG. M

may follow unexpected path and cause
injury. (Fig. L)

• Always keep fingers clear of contact
trip to prevent injury from inadvertent
release of nails. (Fig. M)

• Refer to the Maintenance and Repairs
sections for detailed information on
the proper maintenance of the tool

• Always operate the tool in a clean,
lighted area. Be sure the work surface

is clear of any debris and be careful not

to lose footing when working in elevated

environments such as rooftops.

• Do not drive fasteners near edge
of material. The workpiece may split

causing the fastener to ricochet, injuring

you or a co-worker. Be aware that the nail

may follow the grain of the wood (shiner),
causing it to protrude unexpectedly from

the side of the work material. Drive the

nail perpendicular to the grain to reduce
risk of injury. (Fig. N)

• Do not drive nails onto the heads
of other fasteners or with the tool
at too steep an angle. Personal injury

from strong recoil, jammed fasteners, or

ricocheted nails may result. (Fig. O)

• Be aware of material thickness when
using the nailer. A protruding nail may

cause injury.

• Be aware that when the tool is being
utilized at pressures on the high end
of its operating range, nails can be
driven completely through thin or

very soft work material. Make sure

the pressure in the compressor is set so
that nails are set into the material and not

pushed completely through. (Fig. P)

FIG. N

FIG. O

FIG. P

English

3

• Keep hands and body parts clear of
immediate work area. Hold workpiece

with clamps when necessary to keep
hands and body out of potential harm. Be
sure the workpiece is properly secured
before pressing the nailer against the
material. The contact trip may cause the
work material to shift unexpectedly.

English

(Fig.Q)

• Do not use tool in the presence of
flammable dust, gases or fumes. The

tool may produce a spark that could
ignite gases causing a fire. Driving a nail
into another nail may also cause a spark.
(Fig.R)

• Keep face and body parts away from
back of the tool cap when working
in restricted areas. Sudden recoil can

result in impact to the body, especially
when nailing into hard or dense material.
(Fig. S)

• Grip tool firmly to maintain control
while allowing tool to recoil away
from work surface as fastener is
driven. In “Contact Actuation Mode” if

contact trip is allowed to recontact work
surface before trigger is released an
unwanted fastener will be fired.

• Choice of triggering method is
important. Check the manual for triggering options.

FIG. Q

FIG. R

FIG. S

BUMP/CONTACT ACTION TRIGGER

FIG. T

• When using the contact action
trigger, be careful of unin tentional
double fires resulting from tool
recoil. Unwanted fasteners may be

driven if the contact trip is allowed to
accidentally re-contact the work surface.
(Fig. T)

TO AVOID DOUBLE FIRES:

• Do not engage the tool against the
work surface with a strong force.

• Allow the tool to recoil fully after each actuation.

• Use sequential action trigger.

• When “contact” actuating the nailer, always keep tool in
control. Inaccurate placement of tool can result in misdirected

discharge of a fastener.

SEQUENTIAL ACTION TRIGGER

• When using the sequential action

FIG. U

trigger, do not actuate the tool
unless the tool is placed firmly
against the workpiece.

• DEPTH ADJUSTMENT: To reduce
risk of serious injury from accidental
actuation when attempting to adjust
depth, ALWAYS;

• Disconnect air supply

• Avoid contact with trigger during
adjustments

• Do not drive nails blindly into walls, floors or other work
areas. Fasteners driven into live electrical wires, plumbing, or other

types of obstructions can result in injury. (Fig.U)

4

• Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool while
tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in

serious personal injury.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to
filter out microscopic particles.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday
eyeglasses are NOT safety glasses. Also use face or dust mask
if operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA/Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Tool Specifi cations

MODEL DWFP72155
DESCRIPTION 15 GA "DA" Style Angled Finish Nailer
ENGINE TYPE Oil-Free
OPERATION PRESSURE
RANGE
MAXIMUM OPERATION
PRESSURE

70–120 psi (4.9 – 8.43kg/cm

120 psi (8.43 kg/cm

2

)

AIR CONSUMPTION AT A
RATE OF 60 FASTENERS

1.8 cfm @ 80 psi (5.6 kg/cm2)

PER MINUTE*
FASTENER TYPE DA Style
FASTENER GAUGE
FASTENER RANGE

15 Gauge
1-1/4"–2-1/2" (31mm – 63mm)

MAGAZINE CAPACITY Up to 100 Nails
LENGTH 12.8" (325mm)
WIDTH 3.8" (97mm)
HEIGHT 12.1" (307mm)
WEIGHT 4.22lbs (1.9kg)

* The DWFP72155 requires 1.8 cubic feet per minute or cfm (51.0

liters per minute or lt/min) of free air at 80 PSI (5.6 kg/cm
at a rate of 60 fasteners per minute.

To determine the appropriately sized air compressor, take the actual

rate at which the tool will be run and compare the required C.F.M.
(LT/MIN) to the compressors free air delivery (cfm/ lt/min) at 80 psi
(5.6 kg/cm

2

).

For example, if your fastener usage averages 30 fasteners per minute,
you need 50% of the tools cfm required to operate the tool at the
rate of 60 fasteners per minute. In this case, be sure that your air
compressor can deliver a minimum of 0.9 c.f.m. (25.5 lt/min) at 80 psi
(5.6 kg/cm

2

) for optimum performance of the DWFP72155.

5

2

)

2

) to operate

English

COMPONENTS (FIG.1)

A. Trigger
B. Trigger mode selector
C. Jam clearing latch
D. Contact trip
E. No-mar pad
F. Magazine

English

FIG. 1

B

C

OPERATION

G. Pusher
H. Swivel air inlet
I. Rear exhaust
J. Adjustable belt hook
K. Depth adjustment wheel
L. Pencil sharpener

J

A

K

F

G

D

L

I

H

Preparing the Tool

WARNING: Read the section titled Important Safety Instructions

at the beginning of this manual. Always wear eye and ear protection
when operating this tool. Keep the nailer pointed away from yourself
and others. For safe operation, complete the following procedures
and checks before each use of the nailer.

CAUTION: NEVER spray or in any other way apply lubricants or

cleaning solvents inside the tool. This can seriously affect the life and
performance of the tool.

NOTE: These nailers are designed to be used without oil.

1. Before you use the nailer, be sure that the compressor tanks
have been properly drained.

2. Wear proper eye, hearing and respiratory protection.

3. Remove all fasteners from the magazine.

4. Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is not
functioning properly. NEVER use a tool that has the contact trip
restrained in the up position.

5. Check air supply. Ensure that air pressure does not exceed
recommended operating limits, refer to Tool Specifications.

6. Connect air hose.

7. Check for audible leaks around valves and gaskets. Never use
a tool that leaks or has damaged parts.

WARNING: To reduce the risk of personal injury, disconnect tool

from air supply before performing maintenance, clearing a jammed
fastener, leaving work area, moving tool to another location or
handing the tool to another person.

E

6

Mode Selection

WARNING: Always wear proper eye [ANSI Z87.1 (CAN/CSA

Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating

this tool.

WARNING: Keep fingers AWAY from trigger when not driving

fasteners to avoid accidental firing. NEVER carry tool with finger on
trigger. In contact mode tool will fire a fastener if safety is bumped
while trigger is depressed.

Sequential Trip

Sequential trip requires the operator to hold the trigger against the
work surface before pulling the trigger. This makes accurate fastener
placement easier. The sequential trip allows exact fastener placement
without the possibility of driving a second fastener on recoil, as
described under Contact Trip. The sequential trip tool has a positive
safety advantage because it will not accidentally drive a second
fastener if the tool is contacted against the work surface or anything
else while the operator is holding the trigger pulled.

Bump/Contact Action

The common operating procedure on contact trip tools is for the

operator to contact the work surface to actuate the trip mechanism
while keeping the trigger pulled, thus driving a fastener each time the
work is contacted. This will allow rapid fastener placement on many
jobs. All pneumatic tools are subject to recoil when driving fasteners.

The tool may bounce, releasing the trip, and if unintentionally allowed

to recontact the work surface with the trigger still actuated (finger still
holding the trigger pulled) an unwanted second fastener will be driven.

TO CHANGE OPERATING MODES (FIG. 1–3)

WARNING: Disconnect air line from tool and remove fasteners

from magazine before making adjustments or personal injury may
result.

SEQUENTIAL TRIP ACTION

Use sequential action for intermittent nailing where very careful and
accurate placement is desired.

To operate the nailer in sequential action

mode:

1. Rotate the trigger mode selector (B)
clockwise to the sequential action position

, as shown in Figure 2.

2. Fully depress nosepiece against the work
surface.

3. Pull trigger.

4. Release trigger.

5. Lift nosepiece off work surface.

6. Repeat steps 2 through 4 for next application.

WARNING: The contact trip needs to be depressed followed by a

trigger pull for each fastener followed by a release of both the contact
trip and trigger after each fastener.

CONTACT TRIP ACTION

Bump/contact action is intended for rapid nailing on flat, stationary
surfaces.

When using bump action, two methods are available: place
actuation and bump actuation.

Rotate the trigger mode selector (B)
counterclockwise to the contact action position

, as shown in Figure 3.

To operate the tool using the PLACE

ACTUATION method:

WARNING: A fastener will fire each time the

trigger is depressed as long as the contact trip
remains depressed.

1. Depress the contact trip against the work surface.

FIG. 2

FIG. 3

English

7

2. Depress the trigger.

To operate the tool using the BUMP ACTUATION method:

1. Depress the trigger.

2. Push the contact trip against the work surface. As long as the
trigger is depressed, the tool will fire a fastener every time the

contact trip is depressed. This allows the user to drive multiple

fasteners in sequence.

WARNING: Do not keep trigger depressed when tool is not in use.

English

Keep the contact trip lock-off engaged in the locked position when
the tool is not in use.

Tool Operation Check (Fig.1)

WARNING: If the tool is dropped or you suspect tool damage

perform tool operation check.

WARNING: Remove all fasteners from tool before performing tool

operation check.

SEQUENTIAL TRIP ACTION

A. Press the contact trip against the work surface, without touching

the trigger.

THE TOOL MUST NOT CYCLE.
B. Hold the tool off the work surface and pull the trigger.
THE TOOL MUST NOT CYCLE.
C. Pull the trigger and press the contact trip against the work

surface.

THE TOOL MUST NOT CYCLE.
D. With finger off the trigger, press the contact trip against the work

surface. Pull the trigger.

THE TOOL MUST CYCLE.

CONTACT TRIP ACTION

A. With finger off the trigger, press the contact trip against the work

surface.

THE TOOL MUST NOT CYCLE.
B. Hold the tool off the work surface, and pull the trigger.
THE TOOL MUST NOT CYCLE.
C. With the tool off the work surface, pull the trigger. Press the

contact trip against the work surface.

THE TOOL MUST CYCLE.
D. Without touching the trigger, press the contact trip against the

work surface, then pull the trigger.

THE TOOL MUST CYCLE.

Loading the Tool (Fig. 4)

WARNING: Keep tool pointed in a safe direction when loading

nails.

WARNING: Never load nails with the contact trip or trigger

activated.

LOAD AND PULL PUSHER (FIG. 4)

1. Load nails through the slot in the rear of the magazine to past
retaining clip.

2. Pull pusher back behind nail stick and release.

3. Ensure magazine pusher is behind the last nail stick.

4. Blow the magazine clean periodically to keep the pusher moving
smoothly and to keep dirt and debris out of the nail channel.

FIG. 4

8

PULL PUSHER TO LOCK BACK AND LOAD (FIG. 5)

CAUTION: Keep fingers clear of pusher to prevent injury.

1. Pull pusher back until it is locked at the end of magazine.

2. Load nails through the slot in the rear of the magazine and past
retaining clip.

3. Press the pusher button to release and allow the pusher to push
behind the nails.

4. Blow the magazine clean periodically to keep the pusher moving
smoothly and to keep dirt and debris out of the nail channel.

FIG. 5

Depth Setting (Fig. 1)

The fastener depth control adjustment feature provides control of

the nail drive depth from flush with or just above the work surface
to shallow or deep countersink.

Rotate depth control adjustment wheel (K) to give the desired depth
of drive.

Belt Hook (Fig. 1)

The integrated belt hook (J) can be rotated to either side of the tool to

accommodate left- or right-handed users.

NOTICE:The belt hook can not be removed.

Using The Integrated Pencil Sharpener
(Fig. 6)

A standard pencil sharpener is integrated into the magazine for the

operator’s convenience. To sharpen a pencil, insert any standard
pencil into the hole and rotate the pencil to the right (clockwise) to
sharpen.

FIG. 6

Integrated Air Blower (Fig. 7)

WARNING: NEVER blow debris toward yourself to others in the

work area.

The integrated air blower helps clean debris while working. Press the

integrated air blower button. Compressed air will be ejected out from
front of the tool. Released the button to stop blowing air.

FIG. 7

English

9

16" (406mm) On Center Gauge (Fig. 8)

16" (406mm) on center gauge helps to indicate stud location.

1. Pull up the on center gauge to rotate to the opposite side.

2. Press on the on center gauge to snap into the magazine.

3. 16" (406mm) is measured from nose to the tip of O.C. gauge to
help find stud.

FIG. 8

English

16" (406mm)

Cold Weather Operation

WARNING: Read the section titled Important Safety Instructions

at the beginning of this manual. Always wear eye and ear protection
when operating this tool. Keep the nailer pointed away from yourself
and others. For safe operation, complete the following procedures
and checks before each use of the nailer.

When operating tools at temperatures below freezing, complete
preparation procedures outlined above and follow the directions
below.

1. Make sure compressor tanks have been properly drained prior

to use. Always drain the compressor tanks at least once daily
while using the nailer. This is especially important in cold weather

because any moisture in the air in the tanks will condense in the
cold temperature.

2. Keep the tool as warm as possible prior to use.

3. Lower air pressure to 80 psi or less.

4. Actuate the tool 5 or 6 times into scrap lumber to lubricate o-rings.

5. Turn pressure up to operating level (not to exceed 120 psi) and
use tool as normal.

Hot Weather Operation

Tool should operate normally. However, keep tool out of direct sunlight

as excessive heat can damage bumpers, o-rings and other rubber
parts.

MAINTENANCE

WARNING: Disconnect air line from tool and remove fasteners

from magazine before making adjustments or personal injury may
result.

Clearing a Jammed Fastener (Fig. 1, 9)

If a fastener becomes jammed in the nosepiece, keep the tool pointed
away from you and follow these instructions to clear:

1. Disconnect the tool from the air supply.

2. Release the pusher (G) so it is no longer applying force to the nail
sticks.

3. Open the jam clearing nose door by pulling down and then up on
the latch. (C)

4. Remove the jammed fastener. In certain circumstances, pliers
may be required to remove the fastener.

5. Close the jam clearing nose door latch.

6. Pull nail pusher back behind nail sticks.

7. Perform tool operation check.

NOTE: Should fasteners continue to jam frequently in nosepiece,
have tool serviced by an authorized D

EWALT service center.

10

FIG. 9

Daily Maintenance Chart

ACTION Drain compressor tanks and hoses daily
WHY Prevents accumulation of moisture in compressor and

nailer

HOW Open petcocks or other drain valves on compressor

tanks. Allow any accumulated water to drain from
hoses

ACTION Clean magazine, pusher, and contact trip mechanism
WHY Permits smooth operation, reduces wear, and

prevents jams

HOW Blow clean with compressed air. The use of oils or

solvents is not recommended as they tend to attract
debris

ACTION Before each use, check to ensure all screws, nuts and

fasteners are tight and undamaged

WHY Prevents jams, leaks and premature failure of tool

parts

HOW Tighten loose screws or other fasteners using the

appropriate hex wrench or screwdriver

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.

Lubrication

CAUTION: NEVER spray or in any other

way apply lubricants or cleaning solvents inside
the tool. This can seriously affect the life and
performance of the tool.

EWALT tools are properly lubricated at the

D
factory and are ready for use. However, it is
recommended that, once a year, you take or
send the tool to a certified service center for a thorough cleaning
and inspection.

Repairs

WARNING: To reduce the risk of serious personal injury, remove

nails from magazine before making any adjustments or servicing this
tool.

Refer to the Troubleshooting Guide at the end of this section.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D
center, a D
personnel. Always use identical replacement parts.

EWALT authorized service center or other qualified service

EWALT factory service

English

11

Accessories

WARNING: Since accessories, other than those offered by

EWALT, have not been tested with this product, use of such

D
accessories with this tool could be hazardous. To reduce the risk of
injury, only D
this product.

Recommended accessories for use with your tool are available

English

at extra cost from your local dealer or authorized service center.
If you need assistance in locating any accessory, please contact
DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD
21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website
www.dewalt.com.

EWALT, recommended accessories should be used with

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will
serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required
under the Consumer Product Safety Act.

Seven Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials
or workmanship for seven years from the date of purchase. This
warranty does not cover part failure due to normal wear or tool
abuse. For further detail of warranty coverage and warranty repair
information, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights
which vary in certain states or provinces.

In addition to the warranty, D

EWALT will maintain the tool and replace worn parts caused by

D
normal use, for free, any time during the first year after purchase.
Nailer wear items, such as o-rings and driver blades, are not covered.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your
DEWALT Power Tool, Laser, or Nailer for any reason, you can return
it within 90 days from the date of purchase with a receipt for a full
refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold
in Latin America. For products sold in Latin America, see country
specific warranty information contained either in the packaging, call
the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-4-D
replacement.

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT for a free

12

TROUBLESHOOTING GUIDE

FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D

SYMPTOM CAUSE FIX

Trigger valve housing leaks air O-ring cut or cracked Replace O-ring
Trigger valve stem leaks air O-ring/seals cut or cracked Replace trigger valve assembly
Frame/nose leaks air O-ring or gasket is cut or cracked Replace O-ring or gasket

Frame/cap leaks air Damaged gasket or seal Replace gasket or seal

Failure to cycle Air supply restriction Check air supply equipment

Failure to complete cycle Debris in nose, door, contact arm area Clean nose, door, contact arm area

MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW.

EWALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.

WARNING: To reduce the risk of serious personal injury, remove

fasteners from magazine before making any adjustments or servicing this tool.

Bumper cracked/worn Replace bumper

Cracked/worn head valve Replace head valve
Loose cap screws Tighten and recheck

Worn head valve Replace head valve
Broken cylinder cap spring Replace cylinder cap spring
Head valve stuck in cap Disassemble / Check

English

13

TROUBLESHOOTING GUIDE

FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D

SYMPTOM CAUSE FIX

Lack of power; slow to cycle Broken cylinder cap spring Replace cap spring

English

Skipping fasteners; intermittent
feed

MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW.

WARNING: To reduce the risk of serious personal injury, remove

fasteners from magazine before making any adjustments or servicing this tool.

Rings/seals cut or cracked Replace rings/seals
Exhaust blocked Check bumper, head valve spring

Trigger assembly worn/leaks Replace trigger assembly

Dirt/tar build up on driver Disassemble nose/driver to clean
Cylinder sleeve not seated correctly on bottom bumper Disassemble to correct
Air pressure too low Check air supply equipment
Clogged air filter Clean or replace air filter
Worn bumper Replace bumper
Debris in nose, door, contact arm area Clean nose, door, contact arm area
Air restriction/inadequate air flow through quick disconnect
socket and plug
Worn piston ring Replace ring, check driver
Damaged pusher spring Replace spring
Low air pressure Check air supply system to tool
Loose magazine nose screws Tighten all screws
Fasteners too short for tool Use only recommended fasteners
Bent fasteners Discontinue using these fasteners
Wrong size fasteners Use only recommended fasteners
Leaking head cap gasket Tighten screws/replace gasket

Trigger valve O-ring cut/worn Replace O-ring

Broken/chipped driver Replace driver (check piston ring)
Dry/dirty magazine Clean

EWALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.

Replace quick disconnect fittings

14