DeWalt DW713 TYPE1 Owner’s Manual
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE,
CALL 1-800-4-DEWALT
IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S QUALITY
IMPROVEMENT PROGRAM.
Questions? See us on the World Wide Web at www.dewalt.com
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW713
INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA
DE GARANTiA. ADVERTENCIA: LI2ASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
10" (254 mm) Compound Miter Saw
Scie _longlets mixtes de 254 mm (10 po)
Sierra ingletadora compuesta de 254 mm (10")
Table of Contents
DEFINITIONS: SAFETY GUIDELINES ............................................................................. 1
IMPORTANT SAFETY INSTRUCTIONS .......................................................................... 1
DOUBLE INSULATION/POLARIZED PLUG INSTRUCTIONS ........................................ 1
SAFETY INSTRUCTIONS FOR ALL TOOLS ........................................................ 1
ADDITIONAL SAFETY RULES .......................................................................... 2
ELECTRICAL CONNECTION ............................................................................ 3
UNPACKING YOUR SAW ................................................................................ 3
FAMILIARIZATION ......................................................................................... 3
SPECIFICATIONS .......................................................................................... 4
OPTIONAL ACCESSORIES ............................................................................. 4
ACCESSORIES ................................................................................................................. 4
BENCH MOUNTING ........................................................................................ 5
CHANGING OR INSTALLING A NEW SAW BLADE ............................................. 5
TRANSPORTING THE SAW ............................................................................. 6
ADJUSTMENTS ............................................................................................ 6
MITER SCALE ADJUSTMENT ................................................................... 6
MITER POINTER ADJUSTMENT ............................................................... 6
BEVEL SQUARE TO TABLE ..................................................................................... 6
BEVEL POINTER ....................................................................................................... 6
BEVEL STOP ............................................................................................................. 6
FENCE ADJUSTMENT ............................................................................ 7
GUARD ACTUATION AND VISIBILITY ....................................................... 7
AUTOMATIC ELECTRIC BRAKE .............................................................................. 7
MITER LOCK ADJUSTMENT .................................................................................... 8
BRUSHES ..................................................................................................... 8
OPERATION .................................................................................................. 8
SWITCH ...................................................................................................................... 8
CUTTING WITH YOUR SAW .................................................................................... 8
CROSSCUTS ................................................................................................................ 8
BEVEL CUTS ................................................................................................................ 9
QUALITY OF CUT ........................................................................................................ 9
BODY AND HAND POSITION ..................................................................................... 9
CLAMPING THE WORKPIECE ................................................................................. 9
TO INSTALL CLAMP ................................................................................................. 10
SUPPORT FOR LONG PIECES ............................................................................. 10
CUTTING PICTURE FRAMES, SHADOW BOXES
AND OTHER FOUR SIDED PROJECTS ................................................................ 10
CUTTING TRIM MOLDING AND OTHER FRAMES .............................................. 10
CUTTING COMPOUND MITERS ............................................................................ 11
MITER SCALE .......................................................................................................... 11
VERNIER SCALE ....................................................................................................... 11
WHEN MITERING TO THE RIGHT ......................................................................... 11
WHEN MITERING TO THE LEFT ........................................................................... 11
CUTTING BASE MOLDING ..................................................................................... 11
CUTTING CROWN MOLDING ................................................................................ 12
SPECIAL CUTS ............................................................................................................... 13
MAINTENANCE ............................................................................................................... 14
REPAIRS ......................................................................................................................... 14
WARRANTY .................................................................................................................... 14
TROUBLESHOOTING GUIDE ........................................................................................ 15
COMPOUND MITER CUT REFERENCE CHART ......................................................... 16
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
_&DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
i_ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided,
k may result in property damage, j
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT
TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
IMPORTANT SAFETY INSTRUCTIONS
_ WARNING: Read all instructions before operating product. Failure to follow
all instructions listed below may result in electric shock, fire and/or serious
injury.
READ ALL INSTRUCTIONS
Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool's electrical
system. Tools built with this insulation system are not intended to be grounded. As a result,
your tool is equipped with a two prong plug which permits you to use extension cords
without concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting
from a possible electrical insulation failure within the tool.
ACAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
Repair or replace damaged cords.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the
risk of electric shock. When provided, this plug will fit in the polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Safety Instructions For All Tools
This miter saw accepts the DEWALT worklight and laser attachments.
A WARNING: To reduce the risk of eye injury, AL WAYS use eye protection when
operating the miter saw.
• KEEP GUARD IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from spindle before turning tool on. Tools,
scrap pieces, and other debris can be thrown at high speed, causing injury.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use ofpower
tools in damp or wet locations or in rain can cause shock or electrocution. Keep your
work area well-lit to avoid tripping or placing arms, hands, and fingers in danger.
• KEEP CHILDRENAWAY. All visitors shouldbe keptata safe distance from workarea.
Your shop is a potentially dangerous environment.
• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing
starter keys. The unauthorized start-up of a machine by a child or visitor may result in
injury.
• DON'T FORCE TOOL. It will do the job better and be safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not
designed. Using the incorrect tool or attachment may result in personal injury.
• WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or
other jewelry to get caught in moving parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair. Air vents may cover moving parts and
should also be avoided.
• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. AL WAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI $12.6 ($3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory protection
• SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece on the table
and against the fence or when your hand will be dangerously close to the blade [within
6" (152 mm)]. It is safer than using your hand and it frees both hands to operate tool
• DON'T OVERREACH. Keep proper footing and balance at all times. Loss of balance
may cause personal injury.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories. Poorly
maintained tools and machines can further damage the tool or machine and/or cause
injury.
• TURN THE MACHINE "OFF'; AND DISCONNECT THE MACHINE FROM THE
POWER SOURCE before installing or removing accessories, before adjusting or
changing set-ups, when making repairs or changing locations. An accidental start-up
can cause injury. Do not touch the plug's metal prongs when unplugging or plugging in
the cord.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is
in the "OFF" position before plugging in the power cord.
• USE PROPER EXTENSION CORD. Make sure your extension cord is in good
condition, ff your product is equipped with a cordset, use only 3-wire extension cords
that have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool's
plug. When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct size
to use depending on cord length and nameplate ampere rating, ff in doubt, use the next
heavier gague. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet (meters)
Ampere Rating
More
Than
0
6
10
12
Not More
Than
6
10
12
16
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
18
18
16
14
AWG
16
16
16
12
16 14
14 12
14 12
Not Recommended
• CHECK for DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function--check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged should be properly repaired or
replaced. Do not use tool if switch does not turn it on and off.
• USERECOMMENDEDACCESSORIES. Useonlyaccessoriesthatarerecommended
by the manufacturer for your model Accessories that may be suitable for one tool
may be hazardous when used on another tool Consult the instruction manual for
recommended accessories. The use of improper accessories may cause risk of injury
to persons.
• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave
tool until it comes to a complete stop. Serious injury can result.
• DO NOT OPERATE ELECTRIC TOOLS NEAR FLAMMABLE LIQUIDS OR IN
GASEOUS OR EXPLOSIVE ATMOSPHERES. Motors in these tools may spark and
ignite fumes.
• STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO
NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE
OF DRUGS or ALCOHOL. A moment of inattention while operating power tools may
result in injury.
Additional Safety Rules For Miter Saws
J&WARNING: Do not allow familiarity (gained from frequent use of your saw) to replace
safety rules. Always remember that a careless fraction of a second is sufficient to inflict
severe injury.
• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed
according to the instructions. A machine incorrectly assembled can cause serious
injury.
• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you
are not thoroughly familiar with the operation of this machine. Knowledge is safety.
• STABILITY. Make sure the miter saw is placed on a secure supporting surface and
does not slip or move during use. ff the mobility kit is installed, raise the moveable
caster(s) so saw is in its stationary position.
• FOLLOW ALL WIRING CODES and recommended electrical connections to prevent
shock or electrocution. Protect electric supply line with at least a 15 ampere time-delay
fuse or a circuit breaker."
• MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade
should point in the direction of rotation as marked on the saw.
• TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps
can cause parts or the workpiece to be thrown at high speeds.
• BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are
against blade and arbor screw is tightened securely. Loose or improper blade clamping
may result in damage to the saw and possible personal injury.
• ALWAYS USE A SHARP BLADE. Check the blade to see if it runs true and is free
from vibration. A dull or a vibrating blade can cause damage to the machine and/or
serious injury.
• DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE
for the saw. Overheating, damage to the tool and personal injury may occur.
• DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage
to tool and possible personal injury may occur.
• DO NOT force cutting action. Stalling or partial stalling of motor can cause damage. To
the machine or blade and/or serious injury.
• ALLOW THE MOTOR TO COME TO FULL SPEED prior to starting cut. Starting the
cut too soon may cause damage to the machine or blade and/or serious injury.
• NEVER CUT FERROUS METALS (Those with any iron or steel content) or masonry.
Either of these can cause the carbide tips to fly off the blade at high speeds causing
serious injury.
• DO NOT USE ABRASIVE WHEELS. The excessive heat and abrasive particles
generated by them may damage the saw and cause personal injury.
• NEVER have any part of your body in line with the path of the saw blade. Personal
injury will occur.
• NEVER apply blade lubricant to a running blade. Applying lubricant could cause your
hand to move into the blade resulting in serious injury.
• DO NOTplace either hand in the blade area when the saw is connected to the power
source. Inadvertent blade activation may result in serious injury.
• DO NOT PERFORM FREE-HAND OPERA TIONS (workpiece not supported by table
and fence). Hold the work firmly against the fence and table. Free-hand operations on
a miter saw could cause the workpiece to be thrown at high speeds, causing serious
injury.
• NEVER REACH AROUND or behind the saw blade. A blade can cause serious
injury.
• DO NOT reach underneath the saw unless it is unplugged and turned off. Contact with
saw blade may cause personal injury.
• SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can
possibly cause the machine to slide, walk, or tip over, causing serious injury.
• USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best
results, do not use carbide tipped blades with hook angles in excess of 7 degrees. Do
not use blades with deep gullets. These can deflect and contact the guard, and can
cause damage to the machine and/or serious injury.
• USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to
prevent damage to the machine and/or serious injury.
• INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or
damaged blade can come apart and pieces can be thrown at high speeds, causing
serious injury. Replace cracked or damaged blades immediately.
• CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade
and blade clamps allows you to check for any damage to the blade or blade clamps. A
cracked or damaged blade or blade clamp can come apart and pieces can be thrown
at high speeds, causing serious injury.
• DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the
plastic guard. The polycarbonate material used in the guard is subject to attack by
certain chemicals.
• AL WAYS USE THE KERF PLATE AND REPLACE THIS PLA TE WHEN DAMAGED.
Small chip accumulation under the saw may interfere with the saw blade or may cause
instability of workpiece when cutting.
• USE ONL Y BLADE CLAMPS specified for this tool to prevent damage to the machine
and/or serious injury.
• CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can
cause the machine to overheat, damaging the machine and possibly causing a short
which could cause serious injury.
• KEEP ARMS, HANDS, AND FINGERS away from the blade to prevent severe cuts.
Clamp all workpieces that would cause your hand to be within 6" (152 mm) of the saw
blade.
• NEVER LOCK THE SWITCH IN THE "ON" position. Severe personal injury may
result.
• TURN OFF THE MACHINE and allow the blade to come to a complete stop before
raising the arm and prior to cleaning the blade area, removing debris in the path of the
blade, before servicing or adjusting tool A moving blade can cause serious injury.
• PROPERLY SUPPORT LONG OR WIDE WORKPIECES. Loss of control of the
workpiece can cause injury.
• NEVER cross arms in front of blade while using tooL Always make a dry run
(unpowered) before making a finish cut so that you can check the path of the blade or
severe personal injury may result.
• ADDITIONAL INFORMATION regarding the safe and proper operation of power
tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Avenue, Cleveland, OH 44115-2851 (www.powertoollnstitute.com). Information is also
available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-
3201. Please refer to the American National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
_ WARNING: Do not connect unit to electrical power source until complete instructions
are read and understood.
WARNING: Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
A WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON
THE TABLE AND AGAINST THE FENCE.
A WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
A WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
For your convenience and safety, the following warning labels are on your miter saw.
ON MOTOR HOUSING:
_WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL
BEFORE OPERA TING SAW.
WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS.
AL WAYS WEAR EYE PROTECTION.
DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.
ON MOVING FENCE:
AL WAYS ADJUST FENCE PROPERL Y
BEFORE USE. CLAMP SMALL PIECES
BEFORE CUTTING. SEE MANUAL.
[ O,PROP,RLY.,FOR,U,,
: D'UTIUSATION,
CLAMPSMALLPIECESBEFORECUTTING.SEEMANUAL
AJUSTE LA OUiA DEBIDAMENTE ANTES DE UTlUZAR LA
HERRAMIENTA. ASEGURE LAS PIEZAS PEQUE_IAS ANTES DE
CORTAOLAS, CONSULTE EL MANUAL
TODJOURS SEGLER LE GUIDE AVANT t:UTILISATION, FIXER LES
PETITS OBJETS AVANT DE LES SCIER, CONSULTER LE GUIDE
ON GUARD:
DANGER - KEEP A WAY FROM BLADE.
ON UPPER GUARD:
PROPERL Y SECURE BRACKET WITH BOTH SCREWS BEFORE
USE.
KEEP AWAY
FROM BLADE
MA_TENEKS ALEJADO
BE LA HOJA
S'ELOIGNEK DE LA LAME
ON TABLE: (2 PLACES)
i_ WARNING: FOR YOUR OWN SAFETY READ INSTRUCTION
MANUAL BEFORE OPERA TING MITER SAW.
KEEP HANDS OUT OF PATH OF SAW BLADE.
DO NOT OPERA TE SAW WITHOUT GUARDS IN PLACE.
CHECK LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE.
ALWAYS TIGHTEN ADJUSTMENT BEFORE USE. DO NOT PERFORM ANY
OPERA TION FREEHAND.
NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS IN FRONT
OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO STOP BEFORE
MOVING WORKPIECE, CHANGING SETTINGS OR MOVING HANDS.
DISCONNECT POWER BEFORE CHANGING BLADE OR SERVICING.
TO REDUCE THE RISK OF INJURY, ALLOW SAW TO RETURN TO THE
FULL UP POSITION AFTER EACH OPERATION. THINK! YOU CAN PREVENT
ACCIDENTS.
ON BASE: (2 PLACES)
Electrical Connection
Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that
your saw will operate on alternating current only. A voltage decrease of 10 percent or more
will cause a loss of power and overheating. All DEWALT tools are factory tested. If this tool
does not operate, check the power supply.
Unpacking Your Saw
Check the contents of your miter saw carton to make sure that you have received all parts.
In addition to this instruction manual, the carton should contain:
1. One No. DW713 miter saw with blade.
2. One blade wrench in wrench pocket shown in Figure 2.
3. One No. DW7053 Dust Bag.
Familia riza lion
Your miter saw is fully assembled in the carton. FIG. 1
Open the box and lift the saw out by the
convenient carrying handle, as shown in Figure
1.
Place the saw on a smooth, flat surface such as
a workbench or strong table.
Examine Figures 2 and 3 to become familiar
with the saw and its various parts. The section
on adjustments will refer to these terms and you
must know what and where the parts are.
_CAUTION: Pinch Hazard. To reduce the risk of
injury, keep thumb underneath the handle when pulling the handle down. The lower guard
will move up as the handle is pulled down which could cause pinching. The handle is placed
close to the guard for special cuts.
Press down lightly on the operating handle and pull out the lock down pin, as shown in
Figure 4. Gently release the downward pressure and allow the arm to rise to its full height.
Use the lock down pin when carrying the saw from one place to another. Always use the
carrying handle to transport the saw or the hand indentations shown in Figure 3.
Specifications
CAPACITY OF CUT
50° miter left and right
48° bevel left: 3° right
0° miter
Max. Height 3.5" (89 mm)
Max. Width 6.1" (155 mm)
Result Width 3.5" (89 mm)
Result Height 1.25" (32 mm)
45° miter
Max. Height 3.5" (89 mm)
Max. Width 4.2" (107 mm)
Result Width 2.4" (61 mm)
Result Height 1.25" (32 mm)
45° bevel
Max. Height 2.3" (58 mm)
Max. Width 6.1" (155 mm)
Result Width 3.5" (89 mm)
Result Height .75" (19 mm)
31.62 ° miter and 33.85 ° bevel
Max. Width 5.25" (133 mm)
Result Height .9" (23 mm)
DRIVE
120 Volt Motor
2200 Watts
5000 RPM
Carbide Tooth Blade
15 Amp Motor
Cut Helical Gears with Roller and Ball Bearings
Automatic Electric Brake
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other
locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use
care in selecting and using accessories.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled.
Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support (see drawing). It is used to make repetitive cuts
of the same length from 0 to 42" (107 cm).
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053 (Included with some models)
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Laser Guide System: DW7187
Powered by the saw, the bright laser line delivers enhanced visibility in low and high
light locations. Easy to install.
Miter Saw LED Worklight System: DWS7085
Lighting used for greater visibility and cutting alignment during operation. Easy to
install.
Miter Saw Replacement Kerr Plate: DW7055
This durable plastic uncut plate limits blade tear out.
DW7080
DW7082
LOCKNUTS
END PLATE
DW7187
DWS7085
DW7084
SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR
HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter
blade. It will not be guarded properly. Use crosscut blades only! Do not use blades
designed for ripping, combination blades or blades with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION J DIAMETER J TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose 10" (254 mm) 40
Fine Crosscuts 10" (254 mm) 60
Woodworkinq Saw Blades (provide smooth, clean cuts)
Fine crosscuts 10" (254 mm) 80
Non-ferrous metals 10" (254 mm) 80
NOTE: For cutting non-ferrous metals, use only saw blades
with TCG teeth designed for this purpose.
ACCESSORIES
_ WARNING: Since accessories, other than those offered by DEWAL T, have not been
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only DEWAL T, recommended accessories should be used with
this product.
Recommended accessories for use with your tool are available for purchase from your local
dealer or authorized service center. If you need assistance in locating any accessory for
your tool, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore,
MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.
Bench Mounting
Holes are provided in all four feet to facilitate bench mounting, as shown in Figure 2. (Two
different sized holes are provided to accommodate different sizes of screws. Use either
hole, it is not necessary to use both.) Always mount your saw firmly to prevent movement.
To enhance the tool's portability, it can be mounted to a piece of 1/2" (12.7 mm) or thicker
plywood which can then be clamped to your work support or moved to other job sites and
reclamped.
NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting
screws don't protrude from the bottom of the wood. The plywood must sit flush on the
work support. When clamping the saw to any work surface, clamp only on the clamping
bosses where the mounting screw holes are located. Clamping at any other point will surely
interfere with the proper operation of the saw.
ACAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not
warped or otherwise uneven, ff the saw rocks on the surface place a thin piece of material
under one saw foot until the saw sits firmly on the mounting surface.
IMPORTANT SAFETY INSTRUCTIONS
Changing or Installing a New Saw Blade (Fig. 5, 6)
_WARNING: To reduce the risk of serious personal injury, turn off the tool
and disconnect it from the power source before attempting to move it, change
accessories or make any adjustments accept as written in laser adjustment
instructions.
CAUTION:
• Never depress the spindle lock button while the blade is under power or coasting.
• Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product
with this miter saw.
Removing the Blade
1. Unplug the saw.
2. Raise the arm to the upper position and raise the lower guard as far as possible.
3. Loosen, but do not remove guard bracket screw until the bracket can be raised far
enough to access the blade screw. Lower guard will remain raised due to the position
of the guard bracket screw.
4. Depress the spindle lock button (Fig. 3) while carefully rotating the saw blade by hand
until the lock engages.
FIG. 2 HANDLE
LEFT SIDE FENCE
CLAMPING KNOB
BENCH
HOLES
WRENCH
HOLES FOR
EXTENSION KIT
OPERATING
GUARD
RIGHT SIDE
BASE
FENCE
TABLE
MITER LOCK
MITER SCALE
LEVER
FIG. 3 MOTOR SWITCH
SPINDLE LOCK HANDLE
BUTTON
MOTOR
HOUSING
LEFT SIDE
MITER
DETENT MITER
MITER SCALE
DETENT HAND SCALE
OVER RIDE INDENTATION
END CAP
TRIGGER
CARRYING
BEVEL
DUST
SPOUT
BEVEL CLAMP
KNOB
FIG.4
FIG.5
FIG.6
BLADE
SCREW
OUTER
CLAMP
GUARD
GUARD
BRACKET
SCREW
WRENCH
\
INNER CLAMP
WASHER
LOCK
DOWN
PIN
5. Keeping the button depressed, use the other hand and
the wrench provided to loosen the blade screw. (Turn
clockwise, left-hand threads.)
6. Remove the blade screw, outer blade clamp, and
blade. The inner blade clamp may be left on the
spindle.
Installing a Blade
1. Unplug the saw.
2. With the arm raised, the lower guard held open and the
guard bracket, place the blade on the spindle against
the inner blade clamp with the teeth at the bottom of
the blade pointing toward the back of the saw.
3. Assemble the outer blade clamp onto the spindle.
4. Install the blade screw and, engaging the spindle lock,
tighten the screw firmly with wrench provided. (Turn
counterclockwise, left-hand threads.)
5. Return the guard bracket to its original position and
firmly tighten the guard bracket screw to hold bracket
in place.
WARNING:
• The guard bracket must be returned
to its original position and the
screw tightened before activating
the saw.
• Failure to do so may allow the guard
to contact the spinning saw blade
resulting in damage to the saw and
severe personal injury.
Transporting the Saw
WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
i_,WARNING: To reduce the risk of serious personal
injury, ALWAYS lock the miter lock handle, bevel lock
handle, down lock pin, and fence adjustment knob before
transporting saw.
In order to conveniently carry the miter saw from place to
place, a carrying handle has been included on the top of
the saw arm, as shown in Figure 3. To transport the saw,
lower the arm and depress the lock down pin shown in
Figure 4.
ADJUSTMENTS
i_ WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
NOTE: Your miter saw is fully and accurately adjusted at
the factory at the time of manufacture. If readjustment due
to shipping and handling or any other reason is required,
follow the steps below to adjust your saw.
Once made, these adjustments should remain accurate.
Take a little time now to follow these directions carefully to
maintain the accuracy of which your saw is capable.
MITER SCALE ADJUSTMENT
Place a square against the saw's fence and blade, as
shown in Figure 7. (Do not touch the tips of the blade
teeth with the square. To do so will cause an inaccurate
measurement.) Unlock miter lock lever (see Fig. 8) and
swing the miter arm until the miter detent locks it at the 0°
miter position. Do not lock miter lock lever. Ifthe saw blade
is not exactly perpendicular to the fence, loosen the three
screws that hold the miter scale to the base (shown in
Fig. 8) and move the scale/miter arm assembly left or right
until the blade is perpendicular to the fence, as measured
with the square. Retighten the three screws. Pay no
attention to the reading of the miter pointer at this point.
MITER POINTER ADJUSTMENT
Unlock miter lock lever and squeeze the miter detent
to move the miter arm to the zero position, as shown in
Figure 8. Unlock the miter lock lever to allow the miter
detent to snap into place as you rotate the miter arm past
zero. Observe the pointer and miter scale through the
viewing opening shown in Figure 9. If the pointer does not
indicate exactly zero, loosen the pointer screw, adjust the
pointer to 0 ° and retighten.
BEVEL SQUARE TO TABLE
To align the blade square to the rotary table, lock the arm
in the down position. Place a square against the blade
taking care to not have the square on top of a tooth, as
shown in Figure 10B. Loosen the Bevel Clamp Knob so
that you can move the Bevel Arm. Move the Bevel Arm
as necessary so that the blade is at 0° bevel to the table.
If the Bevel Arm needs adjustment, loosen the lock nut on
the right side Bevel Stop as shown in Figure 11, and adjust
the stop screw as necessary. Hold the stop screw in place
and tighten the lock nut.
BEVEL POINTER
If the bevel pointer does not indicate zero, loosen the screw
that holds it in place and move the pointer as necessary.
Suggestion: For accuracy, set the top edge so that it
aligns with zero.
BEVEL STOP
To set the 45° bevel stop shown in Figure 12, first loosen
the left side fence clamping knob and slide the left side
fence as far as it will go to the left. Move the arm to the
left until it stops on the left bevel stop screw. If the bevel
pointer does not indicate exactly 45°, loosen the left side
bevel stop lock nut and turn the screw downwards. Move
the arm to the left and tighten the bevel clamp knob firmly
FIG. 7
FIG. 8
FIG.9
ADJUSTMENT
SCREW
(three of these)
MITER
DETENT
MITER
LOCK
LEVER
MITER
SCALE
when the bevel pointer indicates exactly 45°. Adjust the
left side bevel stop screw upwards until it firmly touches
the bevel stop. Retighten the nut while holding the screw
from turning.
To achieve 3° right bevel or 48° left bevel, the stop screws
must be adjusted to allow the arm to move to the desired
location. The bevel stops will need readjustment to the
zero and 45 ° positions after cuts are made.
FENCE ADJUSTMENT
WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
To bevel UP TO 48° left, the left side of the fence can
be adjusted to the left to provide clearance. To adjust
the fence, loosen the knob shown in Figure 13 and slide
the fence to the left. Make a dry run with the saw turned
off and check for clearance. Adjust the fence to be as
close to the blade as practical to provide maximum
workpiece support, without interfering with arm up and
down movement. Tighten knob securely. When the bevel
operations are complete, don't forget to relocate the fence
to the right.
GUARD ACTUATION AND VISIBILITY
,&CAUTION: Pinch Hazard. To reduce the risk of injury,
keep thumb underneath the handle when pulling the
handle down. The lower guard will move up as the handle
is pulled down which could cause pinching.
The blade guard on your saw has been designed to
automatically raise when the arm is brought down and to
lower over the blade when the arm is raised.
The guard can be raised by hand when installing or
removing saw blades or for inspection of the saw. NEVER
RAISE THE BLADE GUARD MANUALLY UNLESS THE
SAW IS TURNED OFF.
NOTE: Certain special cuts will require that you manually
raise the guard. See section on Cutting Base Molding
Up to 3.5" (88.9 ram) High (page 11).
The front section of the guard is Iouvered for visibility
while cutting. Although the louvers dramatically reduce
flying debris, they are openings in the guard and safety
glasses should be worn at all times when viewing through
the louvers.
AUTOMATIC ELECTRIC BRAKE
Your saw is equipped with an automatic electric blade
brake which stops the saw blade within 5 seconds of
trigger release. This is not adjustable.
On occasion, there may be a delay after trigger release to
brake engagement. On rare occasions, the brake may not
engage at all and the blade will coast to a stop.
If a delay or "skipping" occurs, turn the saw on and off 4 or
5 times. Ifthe condition persists, have the tool serviced by
an authorized DEWALT service center.
FIG. 10A
BEVEL
HOUSING
FIG. 10B
FIG. 11
LOCK NUT
BEVEL STOP
STOP SCREW
BEVEL
SCALE
BEVEL
POINTER
SCREW
FIG.12
STOP
SCREW
LOCK
NUT
FIG.13
BEVELSTOP
FIG. 14
LEFTSIDE
SCREW
HOLE FOR PADLOCK
BEVEL
POINTER
BEVEL
CLAMP
KNOB
LEFT SIDE
CLAMPING
TRIGGER
SWITCH
FENCE
KNOB
FIG. 15
SLOTTED
ADJUSTMENT
ROD SET SCREW (IF EQUIPPED)
Always be sure the blade has stopped before removing it
from the kerr. The brake is not a substitute for guards or for
ensuring your own safety by giving the saw your complete
attention.
MITER LOCK ADJUSTMENT (FIG. 15)
The miter lock rod should be adjusted if the table of the
saw can be moved when the miter lock handle is locked
down. To adjust, put the miter lock handle in the up
position. Using a slotted screwdriver, adjust the lock rod in
1/8 clockwise turn increments to increase the lock force.
To ensure the miter lock is functioning properly, re-lock
miter lock handle to a non-detent miter angle.
NOTE: Some models may have a set screw as shown in
Figure 15. Using a 3/32 hex wrench, loosen the set screw
on the pivot pin. Tighten set screw after adjustment is
complete.
Brushes
i_ WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
Inspect carbon brushes regularly by unplugging tool,
removing the motor end cap (Fig. 2), lift the brush spring
and withdraw the brush assembly. Keep brushes clean
and sliding freely in their guides. Always replace a used
brush in the same orientation in the holder as it was prior
to its removal. Carbon brushes have varying symbols
stamped into their sides, and if the brush is worn down to
approximately 1/2" (12.7 mm),the spring will no longer exert
pressure and they must be replaced. Use only identical
DEWALT brushes. Use of the correct grade of brush is
essential for proper operation of electric brake. New brush
assemblies are available at DEWALT service centers. The
tool should be allowed to "run in" (run at no load) for 10
minutes before use to seat new brushes. The electric brake
may be erratic in operation until the brushes are properly
seated (worn in). Always replace the brush inspection cap
after inspection or servicing the brushes.
While "running in" DO NOT TIE, TAPE, OR OTHERWISE
LOCK THE TRIGGER SWITCH ON. HOLD BY HAND
ONLY.
OPERATION
i_ WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
WARNING: Always use eye protection. All users and
bystanders must wear eye protection that conforms to
ANSI Z87.1 (CAN/CSA Z94.3).
Plug the saw into any household 60 Hz power source.
Refer to the nameplate for voltage. Be sure the cord will
not interfere with your work.
SWITCH
To turn the saw on, depress the trigger switch shown in
Figure 14. To turn the tool off, release the switch. There
is no provision for locking the switch on, but a hole is
provided in the trigger for insertion of a padlock to lock
the saw off.
CUTTING WITH YOUR SAW
NOTE: Although this saw will cut wood and many non-
ferrous materials, we will limit our discussion to the cutting
of wood only. The same guidelines apply to the other
materials. DO NOT CUT FERROUS (IRON AND STEEL)
MATERIALS OR MASONRY WITH THIS SAW. Do not
use any abrasive blades.
CROSSCUTS
Cutting of multiple pieces is not recommended but can
be done safely by ensuring that each piece is held firmly
against the table and fence. A crosscut is made by cutting
wood across the grain at any angle. A straight crosscut
is made with the miter arm at the zero degree position.
Set the miter arm at zero, hold the wood on the table and
firmly against the fence. Turn on the saw by squeezing the
trigger switch shown in Figure 14.
When the saw comes up to speed (about 1 second) lower
the arm smoothly and slowly to cut through the wood. Let
the blade come to a full stop before raising arm.
i_CAUTION: Always use a work clamp to maintain
control and reduce the risk of workpiece damage and
personal injury.
Miter crosscuts are made with the miter arm at some angle
other than zero. This angle is often 45 ° for making corners,
but can be set anywhere from zero to 50° left or right. After
selecting the desired miter angle, be sure to tighten the
miter lock lever. Make the cut as described above.
To cut through an existing pencil line on a piece of wood,
match the angle as close as possible. Cut the wood a little
too long and measure from the pencil line to the cut edge
to determine which direction to adjust the miter angle and
recut. This will take some practice, but it is a commonly
used technique.
BEVELCUTS
Abevelcutisacrosscutmadewiththesawbladeata
beveltothewood.Inordertosetthebevel,loosenthe
bevelclampknobandmovethesawtotheleftasdesired.
(It is necessary to move the left side of the fence to
allow clearance). Once the desired bevel angle has been
set, tighten the bevel clamp knob firmly.
Bevel angles can be set from 3° right to 48° left and can
be cut with the miter arm set between zero and 50 ° right or
left. Ensure the fence has been adjusted properly. When
cutting left bevel, or right miter compound cuts, it will be
necessary to remove the adjustable fence.
QUALITY OF CUT
The smoothness of any cut depends on a number of
variables. Things like material being cut, blade type, blade
sharpness and rate of cut all contribute to the quality of
the cut.
When smoothest cuts are desired for molding and other
precision work, a sharp (60-80 tooth carbide) blade and a
slower, even cutting rate will produce the desired results.
Ensure that material does not creep while cutting. Clamp it
securely in place. Always let the blade come to a full stop
before raising arm.
If small fibers of wood still split out at the rear of the
workpiece, apply a piece of masking tape on the wood
where the cut will be made. Saw through the tape and
carefully remove tape when the cut is finished.
For varied cutting applications, refer to the list of
recommended saw blades for your saw and select the
one that best fits your needs (Page 4).
BODY AND HAND POSITION (FIG. 16)
Proper positioning of your body and hands when operating
the miter saw will make cutting easier, more accurate and
safer. Never place hands near cutting area. Place hands
no closer than 6" (152 mm) from the blade. Hold the
workpiece tightly to the table and the fence when cutting.
Keep hands in position until the trigger has been released
and the blade has completely stopped. ALWAYS MAKE
DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO
THAT YOU CAN CHECK THE PATH OF THE BLADE.
DO NOT CROSS HANDS, AS SHOWN IN FIGURE 15A.
Keep both feet firmly on the floor and maintain proper
balance. As you move the miter arm left and right, follow
it and stand slightly to the side of the saw blade. Sight
through the guard louvers when following a pencil line.
CLAMPING THE WORKPIECE
i_ WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
FIG. 16
PROPER HAND POSITION
PROPER HAND POSITION
FIG. 16A
IMPROPER HAND POSITION
IMPROPER HAND POSITION
i_WARNING: A workpiece that is clamped, balanced
and secure before a cut may become unbalanced after
a cut is completed. An unbalanced load may tip the
saw or anything the saw is attached to, such as a table
or workbench. When making a cut that may become
unbalanced, properly support the workpiece and ensure
the saw is firmly bolted to a stable surface. Personal injury
may occur.
i_ WARNING: The clamp foot must remain clamped above
the base of the saw whenever the clamp is used. Always
clamp the workpiece to the base of the saw-not to any
other part of the work area. Ensure the clamp foot is not
clamped on the edge of the base of the saw.
A CAUTION: Always use a work clamp to maintain
control and reduce the risk of workpiece damage and
personal injury.
If you cannot secure the workpiece on the table and
against the fence by hand, (irregular shape, etc.) or your
hand would be less than 6" (152 mm) from the blade, a
clamp or other fixture should be used.
For best results use the DW7082 clamp made for use
with your saw. It is available through your local retailer or
DEWALT service center at extra cost.
Other aids such as spring clamps, bar clamps or C-clamps
may be appropriate for certain sizes and shapes of
material. Use care in selecting and placing these clamps.
Take time to make a dry run before making the cut. The
left fence will slide from side to side to aid in clamping.
TO INSTALL CLAMP (SOLD SEPARATELY)
1. Insert it into the hole behind the fence. The clamp
should be facing toward the back of the miter saw.
The groove on the clamp rod should be fully inserted
into the base. Ensure this groove is fully inserted into
the base of the miter saw. If the groove is visible, the
clamp will not be secure.
2. Rotate the clamp 180° toward the front of the miter
saw.
3. Loosen the knob to adjust the clamp up or down,
then use the fine adjust knob to firmly clamp the
workpiece.
NOTE: Place the clamp on the opposite side of the
base when beveling. ALWAYS MAKE DRY RUNS
(UNPOWERED) BEFORE FINISH CUTS TO CHECK
THE PATH OF THE BLADE. ENSURE THE CLAMP
DOES NOT INTERFERE WITH THE ACTION OF THE
SAW OR GUARDS.
i_ WARNING: A workpiece that is clamped, balanced
and secure before a cut may become unbalanced after
a cut is completed. An unbalanced load may tip the
saw or anything the saw is attached to, such as a table
or workbench. When making a cut that may become
unbalanced, properly support the workpiece and ensure
the saw is firmly bolted to a stable surface.
FIG. 17
FIG. 20
FIG. 21
A.
g.
FIG. 19
FIG. 18
A WARNING: The clamp foot must remain clamped
above the base of the saw whenever the clamp is used.
Always clamp the workpiece to the base of the saw-not to
any other part of the work area. Ensure the clamp foot is
not clamped on the edge of the base of the saw.
SUPPORT FOR LONG PIECES
i_,WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from the
power source before attempting to move it, change
accessories or make any adjustments accept as
written in laser adjustment instructions.
ALWAYS SUPPORT LONG PIECES.
Never use another person as a substitute for a table
extension; as additional support for a workpiece that is
longer or wider than the basic miter saw table or to help
feed, support or pull the workpiece.
For best results, use the DW7080 extension work support
to extend the table width of your saw. Available from your
dealer at extra cost.
Support long workpieces using any convenient means
such as sawhorses or similar devices to keep the ends
from dropping.
CUTTING PICTURE FRAMES, SHADOW BOXES AND
OTHER FOUR-SIDED PROJECTS
To best understand how to make the items listed here,
we suggest that you try a few simple projects using scrap
wood until you develop a "FEEL" for your saw.
Your saw is the perfect tool for mitering corners like the
one shown in Figure 17. Sketch A in Figure 17 shows
a joint made by using the bevel adjustment to bevel the
edges of the two boards at 45 ° each to produce a 90°
corner. For this joint the miter arm was locked in the zero
position and the bevel adjustment was locked at 45°. The
wood was positioned with the broad flat side against the
table and the narrow edge against the fence. The cut could
also be made by mitering right and left with the broad
surface against the fence.
CUTTING TRIM MOLDING AND OTHER FRAMES
Sketch B in Figure 17 shows a joint made by setting the
miter arm at 45° to miter the two boards to form a 90°
corner. To make this type of joint, set the bevel adjustment
to zero and the miter arm to 45°.Once again, position the
wood with the broad flat side on the table and the narrow
edge against the fence.
The two sketches in Figure 17 are for four sided objects
only.
As the number of sides changes, so do the miter and
bevel angles. The chart below gives the proper angles for
a variety of shapes. The chart assumes that all sides are
of equal length. For a shape that is not shown in the chart,
use the following formula. 180° divided by the number of
sides equals the miter or bevel angle.
10
NO.SIDES ANGLEMITERORBEVEL
-EXAMPLES-
4 45°
5 36°
6 30°
7 25.7°
8 22.5°
9 20°
10 18°
CUTTING COMPOUND MITERS
A compound miter is a cut made using a miter angle and a
bevel angle at the same time. This is the type of cut used
to make frames or boxes with slanting sides like the one
shown in Figure 18.
NOTE: If the cutting angle varies from cut to cut, check that
the bevel clamp knob and the miter lock knob are securely
tightened. These knobs must be tightened after making
any changes in bevel or miter.
The chart shown on page 16 will assist you in selecting
the proper bevel and miter settings for common compound
miter cuts. To use the chart, select the desired angle "A"
(Figure 19) of your project and locate that angle on the
appropriate arc in the chart. From that point follow the
chart straight down to find the correct bevel angle and
straight across to find the correct miter angle.
Set your saw to the prescribed angles and make a few
trial cuts. Practice fitting the cut pieces together until you
develop a feel for this procedure and feel comfortable with
it.
EXAMPLE: To make a 4 sided box with 26° exterior
angles (Angle A, Figure 19), use the upper right arc. Find
26° on the arc scale. Follow the horizontal intersecting
line to either side to get miter angle setting on saw (42°).
Likewise, follow the vertical intersecting line to the top or
bottom to get the bevel angle setting on the saw (18°).
Always try cuts on a few scrap pieces of wood to verify
settings on saw.
MITER SCALE
The scale is used when calculating angles. To calculate
the proper miter angle, divide 180° by the number of sides
of the box or frame. Refer to the chart on page 11for some
examples.
VERNIER SCALE (FIG. 23, 24)
Your saw is equipped with a vernier scale for added
precision. The vernier scale allows you to accurately set
miter angles to the nearest 1/4° (15 minutes). To use the
vernier scale follow the steps listed below.
(As an example, let's assume that the angle you want to
miter is 24-1/4 ° right).
1. Turn off miter saw.
2. Set the miter angle to the nearest whole degree desired
by aligning the center mark in the vernier scale, shown
in Figure 23, with the whole degree number etched in
FIG. 23
CENTER MARK ON VERNIER SCALE ALIGNS WITH
DESIRED WHOLE ANGLE ON MITER SCALE
(24 ° RIGHT MITER)
FIG. 24
1/4° VERNIER MARK ALIGNS WITH CLOSEST WHOLE
DEGREE MARK ON MITER SCALE (24-1/4 ° RIGHT MITER)
FIG. 25
the miter scale. Examine Figure 23 closely; the setting
shown is 24 ° right miter.
3. To set the additional 1/4°, squeeze the miter arm lock
and carefully move the arm to the RIGHT until the 1/4°
vernier mark aligns with the CLOSEST degree mark
on the miter scale. In our example, the closest degree
mark on the miter scale happens to be 25°. Figure 24
shows a setting of 24-1/4 ° right miter.
For settings that require partial degrees (1/4, 1/2, 3/4°)
align the desired vernier mark with the CLOSEST degree
mark on the miter scale, as described above. (The plastic
vernier plate is inscribed with marks for 1/4, 1/2, 3/4 and l°.
Only the 1/2° is numerically labeled.)
WHEN MITERING TO THE RIGHT
To increase the miter angle when mitering to the right,
move the arm to align the appropriate vernier mark with the
closest mark on the miter scale to the right. To decrease
the miter angle when mitering to the right, move the arm to
align the appropriate vernier mark with the closest mark on
the miter scale to the left.
WHEN MITERING TO THE LEFT
To increase the miter angle when mitering to the left, move
the arm to align the appropriate vernier mark with the
closest mark on the miter scale to the left. To decrease the
miter angle when mitering to the left, move the arm to align
the appropriate vernier mark with the closest mark on the
miter scale to the right.
CUTTING BASE MOLDING
ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE
MAKING ANY CUTS.
Straight 90° cuts :
Position the wood against the fence as shown in
Figure 21. Turn on the saw, allow the blade to reach full
speed and lower the arm smoothly through the cut.
CUTTING BASE MOLDING UP TO 3.5" (88.9 mm)
HIGH VERTICALLY AGAINST THE FENCE
Position molding as shown in Figure 25.
All cuts are made with the back of the molding against the
fence and bottom of the molding against the base.
INSIDE CORNER: OUTSIDE CORNER:
Left side Left side
1. Miter left 45°
2. Save left side of cut
Right side Right side
1. Miter Right 45° 1. Miter left at 45°
2. Save right side of cut 2. Save right side of cut
Material up to 3.5" (88.9 mm) can be cut as described
above. For wider boards [up to 4.25" (107.95 mm)] several
minor concessions must be made.
When cutting a board between 3.5" (88.9 mm) and 4.25"
(107.95 mm) inwidth the roller on the tip of the guard could
1. Miter right at 45°
2. Save left side of cut
11
hang up on the workpiece. Ifthis occurs, simply place your
right thumb on the upper side of the guard and roll the
guard up just enough to clear the workpiece, as shown in
Figure 28. Once you have cleared the workpiece, you can
release the guard and it will continue to open as the cut
progresses.
When mitering to the right side of a base molding wider
than 3.5" (88.9 mm) standing vertically against the fence
as in Figure 25, the saw can only cut through the board up
to 1 inch from the end of the board. Trying to cut more than
an inch will cause the saw's gear case to interfere with the
workpiece. If you want to cut base molding between 3-1/2"
(88.9 mm) and 4.25" (107.95 mm) wide vertically follow
the directions below.
CUTTING 3.5" (88.9 mm)-4.25" (107.95 mm) BASE
MOLDING VERTICALLY AGAINST THE FENCE
• Position molding as shown in Figure 25.
• All cuts made with the back of the molding against the
fence
INSIDE CORNER:
Left side
1. Position molding with bottom of molding against
the base of the saw
2. Miter left 45°
3. Save left side of cut
Right side
1. Position molding with top of the molding resting on
the base of the saw
2. Miter left 45°
3. Save left side of cut
OUTSIDE CORNER:
Left side
1. Position molding with bottom of molding against
the base of the saw
2. Miter right 45°
3. Save left side of cut
NOTE: If the cut must be made somewhere other than
1" from the end of the molding: cut off the molding at
90° approx. 1" (25.4 mm) longer than your final length
then make the miter cut as described above.
Right side
1. Position molding with bottom of the molding
against the base of the saw
2. Miter left 45°
3. Save the right side of cut
A third method of making the cut necessary is to make a
zero degree miter, 45° bevel cut. Your saw can cut a bevel
6.2" (157.5 mm) wide.
CUTTING BASE MOLDING LAYING FLAT AND USING
THE BEVEL FEATURE
• All cuts made with the saw set at 45° bevel and 0
miter.
FIG. 26
FIG. 27
FIG. 28
• All cuts made with back of molding laying flat on the
saw as shown in Figures 26.
• Move the left side fence out of the path of the blade
before attempting any of the following cuts.
INSIDE CORNER:
Left side
1. Position molding with top of molding against the fence
2. Save left side of cut
Right side
1. Position molding with bottom of the molding against
the fence
2. Save left side of cut
OUTSIDE CORNER:
Left side
1. Position molding with bottom of the molding against
the fence
2. Save right side of cut
Right side
1. Position molding with top of molding against the
fence
2. Save right side of cut
CUTTING CROWN MOLDING
Your miter saw is better suited to the task of cutting
crown molding than any tool made. In order to fit
properly, crown molding must be compound mitered with
extreme accuracy.
The two flat surfaces on a given piece of crown molding
are at angles that, when added together, equal exactly 90°.
Most, but not all, crown molding has a top rear angle (the
section that fits flat against the ceiling) of 52° and a bottom
rear angle (the part that fits flat against the wall) of 38°.
Your miter saw has special pre-set miter detent points at
31.62 ° left and right for cutting crown molding at the proper
angle (Fig. 27). There is also a mark on the Bevel scale
at 33.85 °.
The chart below gives the proper settings for cutting crown
molding. (The numbers for the miter and bevel settings are
very precise and are not easy to accurately set on your
saw.) Since most rooms do not have angles of precisely
90°, you will have to fine tune your settings anyway.
PRETESTING WITH SCRAP MATERIAL IS
EXTREMELY IMPORTANT!
FOR CUTTING CROWN MOLDING LAYING
FLAT AND USING THE COMPOUND FEATURES
1. Move the left side fence out of the path of the blade
before attempting any of the following cuts.
2. Molding laying with broad back surface down flat on
saw table (Fig. 29).
3. The settings below are for all Standard (U.S.) crown
molding with 52° and 38° angles.
12
BEVEL SETTING
TYPE OF CUT
LEFT SIDE, INSIDE CORNER:
33.85 °
1. Top of molding against fence
2. Miter table set right 31.62 °
3. Save left end of cut
RIGHT SIDE, INSIDE CORNER:
33.85 °
1. Bottom of molding against fence
2. Miter table set left 31.62 °
3. Save left end of cut
LEFT SIDE, OUTSIDE CORNER:
33.85 °
1. Bottom of molding against fence
2. Miter table set left 31.62 °
3. Save right end of cut
RIGHT SIDE, OUTSIDE CORNER:
33.85 °
1. Top of molding against fence
2. Miter table set right 31.62 °
3. Save right end of cut
When setting bevel and miter angles for all compound
miters, remember that:
The angles presented for crown moldings are very
precise and difficult to set exactly. Since they can
easily shift slightly and very few rooms have exactly
square corners, all settings should be tested on scrap
molding.
PRETESTING WITH SCRAP MATERIAL IS
EXTREMELY IMPORTANT!
ALTERNATIVE METHOD FOR CUTTING CROWN
MOLDING
Place the molding on the table at an angle between the
fence and the saw table, as shown in Figure 30. Use of
the crown molding fence accessory (DW7084) is highly
recommended because of its degree of accuracy and
convenience. The crown molding fence accessory is
available at extra cost from your local dealer.
The advantage to cutting crown molding using this method
is that no bevel cut is required. Minute changes in the miter
angle can be made without affecting the bevel angle. This
way, when corners other than 90° are encountered, the
saw can be quickly and easily adjusted for them. Use the
crown molding fence accessory (DW7084) to maintain the
angle at which the molding will be on the wall.
INSTRUCTIONS FOR CUTTING CROWN MOLDING
ANGLED BETWEEN THE FENCE AND BASE OF
THE SAW FOR ALL CUTS
1. Angle the molding so the bottom of the molding (part
which goes against the wall when installed) is against
the fence and the top of the molding is resting on the
base of the saw, as shown in Figure 30.
2. The angled fflats" on the back of the molding must rest
squarely on the fence and base of the saw.
FIG. 29
FENCE
TABLE
CROWN MOLDING FLAT ON TABLE AND
FIG. 30
CROWN MOLDING BETWEEN FENCE AND TABLE
AGAINST FENCE
BOTTOM SIDE
OF MOLDING
TOP SIDE
DW 7O84 CROWN
MOLDING FENCE
TABLE
INSIDE CORNER: OUTSIDE CORNER:
Left side Left side
1. Miter right at 45 ° 1. Miter left at 45°
2. Save right side of cut 2. Save right side of cut
Right side Right side
1. Miter left at 45° 1. Miter right at 45 °
2. Save left side of cut 2. Save left side of cut
FIG. 31
BLADE
FENCE
FIG. 32
FENCE
RIGHT
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS
SECURED ON THE TABLE AND AGAINST THE FENCE.
ALUMINUM CUTTING
ALWAYS USE THE APPROPRIATE SAW BLADE MADE
ESPECIALLY FOR CUTTING ALUMINUM. These are
available at your local DEWALT retailer or DEWALT service
center. Certain workpieces, due to their size, shape or
surface finish, may require the use of a clamp or fixture to
prevent movement during the cut. Position the material so
that you will be cutting the thinnest cross section, as shown
in Figure 31. Figure 32 illustrates the wrong way to cut these
extrusions. Use a stick wax cutting lubricant when cutting
aluminum. Apply the stick wax directly to the saw blade
before cutting. Never apply stick wax to a moving blade.
13
The wax, available at most hardware stores and industrial
mill supply houses, provides proper lubrication and keeps
chips from adhering to the blade.
Be sure to properly secure workpiece. Refer to page 4 for
correct saw blade.
BOWED MATERIAL
When cutting bowed material always position it as shown
in Figure 33 and never like that shown in Figure 34.
Positioning the material incorrectly will cause it to pinch the
blade near the completion of the cut.
CUTTING PLASTIC PIPE OR OTHER ROUND
MATERIAL
Plastic pipe can be easily cut with your saw. It should be
cut just like wood and CLAMPED OR HELD FIRMLY
TO THE FENCE TO KEEP IT FROM ROLLING. This is
extremely important when making angle cuts.
CUTTING LARGE MATERIAL
Occasionally you will encounter a piece of wood a little too
large to fit beneath the blade guard. A little extra height
can be gained by rolling the guard up out of the way, as
shown in Figure 28. Avoid doing this as much as possible,
but if need be, the saw will operate properly and make the
bigger cut. NEVER TIE, TAPE, OR OTHERWISE HOLD
THE GUARD OPEN WHEN OPERATING THIS SAW.
MAINTENANCE
DO NOT use lubricants or cleaners (particularly spray
or aerosol) in the vicinity of the plastic guard. The
polycarbonate material used in the guard is subject to
attack by certain chemicals.
1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even
though slots are provided to allow debris to pass
through, some dust will accumulate.
3. The brushes are designed to give you several years
of use. To replace the brushes refer to Brushes on
page 8 or return the tool to the nearest service center
for repair. A list of service center locations is packed
with your tool.
SERVICE INFORMATION
Please have the following information available for all
service calls:
Model Number Serial Number
Date and Place of Purchase
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by a
DEWALT factory service center, a DEWALT authorized
service center or other qualified service personnel. Always
use identical replacement parts.
FIG. 33
FENCE
FIG. 34
CORRECT
INCORRECT
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due
to faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-DEWALT (1-800-
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made or
attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, DEWALT tools are covered by
If you are not completely satisfied with the performance of
your DEWALT Power Tool, Laser, or Nailer for any reason,
you can return it within 90 days from the date of purchase
with a receipt for a full refund - no questions asked.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained either
in the packaging, call the local company or see website for
warranty information.
FREE WARNING LABEL REPLACEMENT: Ifyour warning
labels become illegible or are missing, call 1-800-4-DEWALT
(1-800-433-9258) for a free replacement.
90 DAY MONEY BACK GUARANTEE
our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first
year after purchase.
_--'_ FORyouROWNSAFETY_EADINSTRUCTIO_ _ PARASUP_0PIASEGURiOAO'LEAELMANUALi]_INSTRUCCIONESANTESBE _ POURVOTREPROPRESECURFC_rLIR£LEMOOEO'EMPLOIAVANT%
,AN[_S0_OFPATHO_SAWeL,,OE.OONOTOpE_'rESAWWITHOUTG_JAROSDEL_RAYE_T_E_`_"_`_`DEL_si_A.N_PEeE_AsiERHAsiLasPR_TEc_REs_EsTANA_ecUADAM_N_e`rRA_EcxaiRE_ALAME_E_sciE.NEPt_sUTi_sER_Asc_s_sQuE_s_RE-Mt_i_sNEs_i_NTEN
iNPL_C_.C,_C_{LOWE_GUARD_0RP_OPeRCL0SIN_e_F0_ EAC_US_. NS_DOS VER_IOU_DUEELP_0T_C'r0_NF_RORC_r_ C0_ECTAM_T__NTESOECAD_.USO_US_ SEMPRE _'LAC_.WI_FI_NAVANTCHA_U_USAGe,Q_ L__'A_-_AI_I_E_l_ SE_E_ _IEN._0_J0U_S_IEN
,_.W_ySTZ_TENAD._UST_ENTr_E_0_EUSE._0NOTp_RFORM_Y0_E_TZ0NLA_:_u[Aci_NANTE_oEUTiLizA_L_HE_AM_N_.N_Auc_NiN_uNA_Aci_NsiN_uz_`_sMAN_s. SE_L_SI_E_LA_ESAVA_U_LIS,_T_0N.E_ECrU_TOUT_0PE_TION_TENANT,.'0UTIL_ESDEUX
_E_AND.N_VEI_AC_IN_ACI{0_SAW_LA_.I'_VEI_C_0SS_MSI_NUNCASEEST_r'_A_CANZ_'_A_0_"C_AS_AHOJA_L_S_I_A.NU_CACI_UC_0SBI_AZOS_I_ENTEAMAINS.NE,_AM_ISPASS_tESMAINSAL'AI_I_R_Dt_L_,L_EOEL_SCI_.N_JAMAISPASSER_SB_AS
_0NTOFB_D_.TURNOFFT00_.AP_WAITF0_SAW_L_D_T0STOPB_0R__AH_A.A_ELA"ERRAMi_N_A_sPER_uELA_JAsEDET_N_;_```_Rc0_LET_A_TEsD_TiRA_i_zA DEvA_Tt_AL_`M_._TEiN_EL_u11tE_A_E_DREL'A_e_T_z_AL,`M_DeL_`sci_AvANT[_e_PL_cEe_
_OVIN_WO_{_'I_C_,C,ANGINGSE_N_SO_MeVING_IANDS.DISCONNECTDET_OAJO,A_T_SOE_S_ARL_SI_OAm_S_EMOVEeL_SMANOS.OESCO_ECT_L_-HE_MIENTAA_ES_i_cE`_EM_iFi_RL_R_L_s_uDE[_PL_cERL_s_Ai_s._Ee_Nc_ERLt`sciEAvANTDER_MPL_c_R
POW_BEFO_C_.N_IN_BL_0RS_VlCIN_.T0_ED_C_T,_RISKO__)_A_LEM_NTENiM_ENT_A_T_D_M_IA_t_JA.AFi_D_ci_LRi_sG_D_si_N_sPE_sONA_ U_E_0_P_0C_I_ERAU_ _e_ATIt_N._IND R_DUI_LE_ISQUEDE_L_SS_I_S,_SS_.ASClE
INJU_y,AL_0WSAWT0_XU_TOTI_E_:ULLUPP0SmO_RFTE_ACHR_S_ASlERRAAL,_,p0slCl0NVE,_TICALLt_E_0_Ec_r_Aop_ACION.p_ES'rEA'rEI'_Cl0_US'rE_r'U_DEEVrrA__EvENi_NP_sm_Nc_e`_P_eTEM_N`r_EvEEA_:sc_QU_TiUsA_`i_N.iLs_FF_T_L_cHiR_s
O_'_t=0_. T_IIN_{_YOUCA_e_EWNT,_,CCI__lrs. ACe_N_S. _.CCIOEN_SP_UV_T_T_Evrr_s ,*'
PROPERLYSECURE8RACKET
WiTH BOTH SCREWSOEFOREUSE.
ASEGUBE LA MENSLILA
BEBiDAMENTECONAMMOS
TOmNJLLOS ANTES DE PONER EN
MABCRA LA HERRAMJENTA.
mIENFIXERLE SUPPORT
A EAiDE DESHEUX ViS
AVANT L'UTJLJSATJON.
MAnUA_.BE_0R_0PE_ATI_GMITERSAW._:EE_ PO_E_E_M,_RCRAL_SlER_DEI_GLETE.W,N_GA _S _AN0S_J._JADAS O'UTi_SERLASClEAON,LETS.GA_OERLESr_l_S I{0RSDEL_
" 10"1254=m)
DW713 uo,,,,PuuNu.,.E.SA_
_ I_STRUCTiON MANUAL BEFO$_E OpEI_ATI NG MITER SAW.
WHEN SERVICING, USE ON LY iDENTiCAL _{EPLAC_MENT _ARTS, D ONOT _XPOSE TO _AIN
OR USE 1_ OAMP _.OCA'IIONS. ALWAYS USE P_OPE_ EYE A_O RJ_SPJRATO_Y P_OTE_TION.
# _ I , , _ PABA _ PROPIA SEGtJ]iIDAD, LEA
ANTES DE PONE_ E_ MAF_CH_. LA SIE_$_A DE INGLETE, A LA HOR A DE pffESTAJ]
MANTENiMJ_NTO, SE DEBE_A UTILIZA_ SOLAMENTE PIEZAS JDENTICAS DE
I_EEMpL#20. NO _XpONGA LA HERRA_IENTA A L_ LLUVIA NI LA HAGA FUNCIONA_
E_LOSLUG,_S _U_EOOS.slEra_ s_ O_SERAUT_ZA_L_SGUAROASV
PROTECCBON AP_OPIADA pAPA ESME_ILA_ AL IGUAL QUE PARA pROTEOE_ LA
VISTA YLAS ViAS BESPiRATORIAS.
_ _ , = _=AR MESURE DE SECURJTE. LIRE _E GUIDE
scl__o_rs. Lo_sOEST_AVAU__'_NT_I_N, N'_tUSE_OUEO_Se_EC_S_
RECHANGE IDE_T_QUES. NE PAS EXPOSER UOtlTIL A LA PLUIE NI S'EN SE_VIR OANS
DES ENOROJTS ]_UMJDES, TOUJOURS pORtER DE I:EQUIp£MENT DE pROTECTJtIN
OCLJLP.JR£ ET RE_PIRATOIR£ ApPfiOPRI£.
OEWALT iN DIJSTRIAL TO O L CO., BALTIMORE M D, _1286 USA
_o_SERVICEI_Ol_eaATIO_,C,e,L_I..e00-4-mWA_.Twww._C,e/ALT._om
TO REDUCE THE ]{ISK OF iNJURY, USER MUST READ THE
DETENIDAMEr_TE EL MANUAL DE INSTI_UCCiONES
lYUTiLISATJONAVANT DESE SERVERDE LA
_ SL_MPSMALLPIECESBEFORECUTIlND.SEEMANUAL
J
ALWAYS ADJUST FENCE PROPERLY BEFORE USE, |
A_U_TEEAOOiAUEO_DA_ENTEANTESDEUT_II_AOtA
O_R_EN_ ASEOUOE[AS _EZ_S PEOUEI)ASANTESUE
_ORIARI_S_ _ONSHtT_ELM/WHAt,
_UUJUOOSRE_ER _E O0_D_AVANT_U_ON_ E_X_R_ES
PDllTS _OJETS A_ANTUE_ESSC_ER__BN$O_E_ _E DU_DE
U'U_SAI_UN_
%,
14
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE!
Saw will not start
Saw makes unsatisfactory cuts
Blade does not come up to speed
Machine vibrates excessively
Does not make accurate miter cuts
Material pinches blade
WHAT'S WRONG? WHAT TO DO
11 Saw notpluggedin Plug insawl
2. Fuse blown or circuit breaker 2. Replace fuse or reset circuit breaker.
tripped
3. Cord damaged 3. Have cord replaced by authorized service center.
4. Brushes worn out 4. Have brushes replaced by authorized service center or replace
them yourself as instructed on page 8.
1. Dull blade 1: Replace blade, see page 5.
2. Blade mounted backwards 2. Turn blade around, see page 6.
3. Gum or pitch on blade 3, Remove blade and clean with turpentine and coarse steeIw00!
or household oven cleaner
4. Incorrect blade for work being done 4. Change the blade type, see page 4.
ti Extension cord too light or too long 1: Replace with adequate size cord, see page 1!
2. Low house current 2. Contact your electric company.
ii Saw not mounted seCurely tostand Tighten all mounting hardware, see page ..................
or work bench
2. Stand or bench on uneven floor 2. Reposition on flat level surface, see page 5.
3: Damaged Saw blade &Replace blade' see page 5.
1. Miter scale not adjusted correctly 1. Check and adjust, see page 6.
2. Blade is not square to fence 2. check and adjust' see page 61
3. Blade is not perpendicular to table 3. Check and adjust fence, see page 6.
4. workpiece moving 4. clamp workpiece securely to fence
1. Cutting bowed material 1. Position bowed material as shown on page 13.
15
TABLE 1: COMPOUND MITER CUT
(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
0
45-
10 15 20 25 30 35 40
45
- 45
t_
O
ILl
,--I
(5
¢1
ILl
i-
_e
t_
m
'1-
I-
I--
ILl
t_
40-
35-
20-
15-
- 40
35
3o
25 0
15
Ill
--J
Z
x
rn
t.l_
o
kl.l
n
t.l_
©
t.t.l
._1
z
<
10-
10 15 20 25 30 35 40
SET THIS BEVEL ANGLE ON SAW
16
10
0
45
Loading...