Desa GA2100A User Manual
Instructions For Installing GA2100A Fan Accessory
Carton Contents
• One Fan Accessory
• One Fan Housing
• Four #8 Screws
• One #10 Screw (long)
• Two “U” Nuts
• Three Brackets
• Two #10 Screws
NOTICE
If wall mounted, heater must be disconnected from
gas supply and removed from wall before installing
fan accessory. Contact a qualified service person to
do this. All local codes must be followed.
!
WARNING
WARNING ICON G 001
Fan accessory must be grounded. Fan comes with a
three-prong, grounding plug as shown in Figure 1. The
plug is your protection against electrical shock. Plug it
into a standard, three-hole, grounded, outlet. If cord
needs replacing, use only a cord with a three-prong,
grounding plug.
Grounded Outlet
Wall Mounting Instructions For Models With Mounting
Bracket
1. Mount heater to wall by following steps under INSTALLING TO
WALL in owner’s manual.
2. Plug power cord of fan into grounded outlet.
3. Discard “U” nuts, brackets, and extra screws provided with fan
accessory.
Wall Mounting Instructions For Models With Raised
Mounting Holes
After attaching fan accessory, heater must be mounted to wall in
different manner than what is specified in owner’s manual. Follow
steps below to mount heater to wall.
1. Locate the two raised mounting areas at top of heater back
panel. Each area has a square hole in center and a key hole at
top (see Figure 4).
Key Hole
Square Hole
Raised
Mounting Area
Grounding
Plug
Figure 1 - Grounding Plug
Attaching Fan Accessory
1. Knock out center panel at four tabs with screwdriver (see Figure
2).
2. Position fan housing between fan accessory and heater back panel.
Attach fan accessory and fan housing to heater back panel using
four #8 screws (see Figure 3).
Center
Panel
Figure 2 - Center Panel
Fan
Accessory
Tab
Fan Housing
Figure 4 - Raised Mounting Areas
2. Insert “U” nut into square hole on each mounting area. Attach
“U” nut as illustrated in Figure 5. Push “U” nut into place.
Screw hole on “U” nut should be visible through key hole in
mounting area.
Screw Hole
“U” Nut
Screw Hole
“U” Nut
Figure 5 - Attaching “U” Nut
Continued on Back
#8 Screw
Figure 3 - Attaching Fan Accessory and Fan Housing
3 Attach one bracket to each mounting area. Position bracket as
illustrated in Figure 6. Make sure round hole on bracket is
against heater back panel and key hole is away from heater.
Make sure small portion of key hole is on top (see Figure 6).
Insert #10 screw though round hole in bracket and into “U” nut.
Tighten screw firmly.
Operating Fan
To start fan, turn On/Off switch on. To stop fan, turn On/Off switch
off.
Bracket
#10 Screw
Figure 6 - Attaching Bracket
4. Hang heater on wall. Do this by placing large opening of key
hole (on bracket) over screwheads in wall. Slide heater down on
screws. Screws should be located in small portion of key hole.
5. Position third bracket between bottom screw hole on heater and
wall (see Figure 7). Insert long #10 screw into bottom screw
hole, through mounting bracket, and into wall anchor. Tighten
screw firmly.
6. Replace front panel of heater.
Bracket
Long #10
Screw
Heater Back
Wall
Anchor
Wall
On/Off Switch
Figure 9 - On/Off Switch
LIMITED WARRANTY
DESA International warrants this product to be free from defects
in materials and workmanship for one (1) year from the date of first
purchase, provided that the product has been properly operated.
This warranty is extended only to the original purchaser. DESA
shall either replace the product or refund the full purchase price.
Warranty service is available only through authorized dealers.
This warranty does not apply to the failure of any part resulting
from accident, or misuse by the owner nor does it apply to use in
commercial applications.
To the full extent allowed by the law of the jurisdiction that
governs the sale of the product: this express warranty excludes any
and all other expressed warranties. The above expressed warranty
is in lieu of all other warranties either expressed or implied
including but not limited to the implied warranties of merchantability and fitness for a particular purpose. DESA’s liability is
hereby limited to the purchase price of the product and DESA shall
not be liable for any other damages whatsoever including indirect,
incidental, or consequential damages.
Some states do not allow a limitation on how long an implied
warranty lasts, or an exclusion or limitation of incidental or
consequential damages, so the above limitation or implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
For information about this warranty write:
Figure 7 - Attaching Bottom Mounting Screw
Extension Cord
Use extension cord if needed. The cord must have a three-prong,
grounding plug and a three-hole receptacle. Make sure cord is in
good shape. It must be heavy enough to carry the current needed.
An undersized cord will cause a drop in line voltage. This will
result in loss of power and overheating. Use a No. 18 AWG cord for
lengths less than 50 feet.
Black Black
Plug
Figure 8 - Wiring Diagram For Fan Accessory
Switch
Green
21
BlackWhite
Motor
R
DESA
INTERNATIONAL
P.O. Box 90004
2701 Industrial Drive
Bowling Green, KY 42102-9004
098474-01
REV. F
8/93
Loading...