Denver HSA-120 User guide
DENVER
HSA-120
INSTALLATION AND USER MANUAL
Alarm Security System™
ENG
Features
1. INTRODUCTION ................................................................................................................... 4
1.1 Box Content .................................................................................................................. 4
1.2 Features ....................................................................................................................... 4
1.3 Recommendations ....................................................................................................... 4
1.4 Warnings ...................................................................................................................... 5
2. CONTROL PANEL DESCRIPTION....................................................................................... 5
2.1 Control Panel Features ................................................................................................ 5
2.2 SPECIFICATIONS ....................................................................................................... 7
3. START WITH THE CONTROL PANEL ................................................................................. 7
3.1 Connect the Control Panel ........................................................................................... 8
3.2 Enter Connection Mode................................................................................................ 8
3.2.1 Wireless Remote Control ................................................................................... 9
3.2.2 Wireless Motion Detector ................................................................................. 11
3.2.3 Wireless Door/Window Contact ....................................................................... 16
3.2.4 RFID Tag .......................................................................................................... 19
3.2.5 Register an Additional Denver External Siren ................................................. 19
3.2.6 Zone Setup of Accessories .............................................................................. 19
3.2.7 Clear Accessories ............................................................................................ 20
4. ENTER SETUP MODE ........................................................................................................ 20
4.1 Ringing Time of the Siren ........................................................................................... 21
4.2 Exit Delay & Entry Delay ............................................................................................ 21
4.3 Change Password ...................................................................................................... 21
4.4 Store Phone Numbers ................................................................................................ 21
4.5 Delete Phone Numbers .............................................................................................. 22
4.6 Exit Setup Mode ......................................................................................................... 22
4.7 Alarm Response When Being Out of Home............................................................... 22
4.8 Control by Phone Call ................................................................................................ 22
4.9 Siren Volume .............................................................................................................. 23
5. TELEPHONE CALL/EMERGENCY CALL .......................................................................... 23
6. DENVER HSA-120 APP OPERATION ............................................................................... 24
7. CONTROL PANEL OPERATIONS...................................................................................... 24
8. 8. SMS OPERATIONS ........................................................................................................ 25
8.1 Store Phone Numbers for SMS notifications.............................................................. 26
8.2 Disarm the System ..................................................................................................... 27
8.3 Settings Enquiry ......................................................................................................... 29
8.4 Store Phone Numbers ................................................................................................ 29
8.5 Rename Zones ........................................................................................................... 30
8.6 SMS Alert for Accessory Low Battery ........................................................................ 31
8.7 Rename RFID Tag ..................................................................................................... 32
8.8 Entry and Exit Delay Time .......................................................................................... 33
8.9 Siren Volume and Ringing Time ................................................................................ 34
8.10 Change the Password .............................................................................................. 34
8.11 Change System Language ....................................................................................... 35
8.12 Restore System to Factory Settings by SMS ........................................................... 36
9. FAQ ..................................................................................................................................... 36
10. STANDARDS..................................................................................................................... 37
1. INTRODUCTION
Thank you for purchasing the DENVER - HSA-120 wireless security system.
Read carefully this manual to get the best experience with this product. Keep this manual for
future reference.
The accesories for the alarm system is paired with the control panel from factory side. We
suggest you remove the paper from the battery on one accessory at a time, and register the
name of the zone. This makes it much easier to find out which sensors are giving alarm. (you
can rename them through the app, or SMS (see point 8.5 in this manual)
1.1 Box Content
- 1 x Control Panel (with internal siren)
- 2 x Remote Controls
- 2 x Wireless Motion Detector
- 2 x Wireless Window/Door Contact
- 2 x RFID Tags
- 1 x AC Adaptor
- 2 x 800 mAh Battery (8h in standby mode)
1.2 Features
- Wireless alarm system
- Easy to install
- Control from distance by phone call
- Supports up to 10 Remote Controls, 50 Wireless Accessories
- and 50 RFID Tags
- Radio-frequency security of the accessories: more than one million code combinations
- Easy registration of new accessories
- Built-in 90dB siren to deter potential intruders
- Can store up to 5 phone numbers and 5 SMS numbers
- Arm, disarm and monitor from distance by phone operation
1.3 Recommendations
For your safety, it is recommended to follow the following precautions:
- Do not forget to arm the control panel during your absence and make sure it works
properly.
- Do not forget to lock the doors, windows and other ways out of your home.
- Always keep your remote control with you and do not leave it visible or noticeable.
- To optimize the operation of the alarm system, it is recommended to select carefully the
location where each accessory will be installed. It is recommended to mount the detectors
on a smooth wall, to ensure the proper use of the tamper switch.
- Accessories purchased separately must be connected to the control panel manually.
- Wait until the end of the auto-test before putting back the cover of the detector.
- If you do not use this product for a long time, remove the batteries to optimize their
lifespan.
- Do not cross the beams of different motion detectors.
1.4 Warnings
- The control panel is provided with a separate battery. Do not scrap used batteries
anywhere. They shall be recycled in accordance with the EU Directives 91/157/EEC and
93/86/EEC.
- Do not open the case of the control panel and do not repair it yourself. If you encounter an
issue with the product, contact a qualified personnel (technician or manufacturer's
service).
- Take care of this product and do not let water get into it as it may damage the product.
- Place the control panel in a cool, dry and well-ventilated area. Do not install detectors near
heating, cooling, or ventilation.
- Do not use detergent or other flammable materials to clean this unit.
- Do not let your device fall on the floor.
- Remove the battery holder cover with care.
- DENVER Electronics is not to be held responsible in case of burglary, theft, loss or
damage to house/persons/other, power cut off or any other issues.
2. CONTROL PANEL DESCRIPTION
2.1 Control Panel Features
English Translation
LED GSM Signal LED GSM Signal
Zone LED indicator Zone LED indicator
Arm/Disarm LED indicator Arm/Disarm LED indicator
Setup/Connection LED indicator Setup/Connection LED indicator
Power/Low Power LED indicator Power/Low Power LED indicator
RFID Reader RFID Reader
Arm Arm
Disarm Disarm
Home Mode Home Mode
Phone Call Phone Call
The upper blue LED is the "Arm/Disarm" status indicator. If the system is armed, the LED is on.
If the system is in Home Mode, the LED blinks once every second.
The middle white LED is the Setup and Connection indicator. In Connection and Setup modes,
the LED is on.
The green LED at the bottom is the Power indicator. If the control is properly powered, the LED
is on. If the power of the control panel is too low (<7V), the LED blinks.
GSM signal LED indicator: when there is no GSM signal or no SIM card, the LED indicator will
flash once every second, if GSM find signals, the LED indicator will flash once every
3 seconds.
English Translation
Monitoring MIC Monitoring MIC
Battery Holder Battery Holder
Tamper Switch Tamper Switch
Speaker Speaker
Power Interface Power Interface
Power Switch Power Switch
SIM card socket SIM card socket
Wired Zone Interface Wired Zone Interface
English Translation
Electronic Door Electronic Door
SIM Card Slot SIM Card Slot
Speaker Speaker
Wired Sensor Wired Sensor
Power Interface Power Interface
Power ON/OFF Power ON/OFF
2.2 SPECIFICATIONS
Control panel
- Power supply: Input AC 110~240V-50~60Hz/Output DC 12V-500mA - Internal battery
backup: 3.7V/800 mAh battery pack x 2
- Internal siren: 90dB
- Quantity of accessories supported: 60 (including 10 Remote Control) - Radio frequency:
433MHz (±75 KHz)
- GSM frequencies: 850/900/1800/1900 MHz
- Housing material ABS plastic
- Operating conditions:
Temperature: -10°C~55°C
Humidity: ≤ 80% (non-condensing)
- Panel size (L x W x H): 191 x 131 x 26 mm
3. START WITH THE CONTROL PANEL
Before starting with the control panel, make sure each accessory has been assigned to a zone
and attach the brackets of each element according to the chosen location.
Do not forget to insert the batteries into each accessory and do not put back the cover of the
accessories while testing.
3.1 Connect the Control Panel
The SIM CARD (not included) must have 2G support. Please note that some SIM cards are
only 3G SIM cards (no 2G) and so cannot be used for this alarm system. Also the SIM card
shall be without simlock. If the card is simlocked you need to remove this (e.g. in a mobile
phone) first.
1. Insert the Sim card (NOT included) in the control panel as described in the drawing below.
2. Plug the adaptor into AC power socket.
3. Switch the device on.
4. Turn on the control panel.
3.2 Enter Connection Mode
1. Press the "#" key. Then press the "1" key on the control panel to activate the connection
mode. The Connection LED indicator lights up. Trigger the alarm on the wireless accessory
to connect it to the control panel.
2. Press the Disarm key ( ) on the control panel to exit the Connection mode.
3. While in Setup mode, enter "* 22 * password *" (DEFAULT PASSWORD:1234) on the
control panel to clear the connection to all the connected accessories.
3.2.1 Wireless Remote Control
English Translation
Disarm Disarm
LED indicator LED indicator
Arm Arm
SOS SOS
Home Mode Home Mode
Arm the system
Press the Arm button " " to arm the alarm system. The LED indicator lights up (the control
panel beeps once). The system is armed.
If an intruder is detected, the siren rings out. (The siren turns off after 3 minutes as per default
settings.) In the meantime, the system dials the pre-stored phone numbers automatically.
Disarm the system
Press the Disarm button " " to disarm the alarm system. The LED indicator turns off (the
control panel beeps twice). The system is disarmed.
Home Mode
Press the Home Mode button " " on the remote control. The system state LED is on and
flashes. All the sensors in regular zones are armed except those in the Home Mode zone. The
sensors in the Home Mode zone are disarmed so that users can move inside their home.
Mute Mode
Press the Home Mode button " " and the Arm " " or Disarm " " button immediately after.
Doing so, the control panel does not ring out when you arm or disarm your system.
Emergency Mode
Regardless the status of the system, the alarm is triggered when the SOS button "SOS" is
pressed on the remote control.
At the same time, the control panel sends a notification by SMS ("RC-01 SOS", 01 being the
remote control's number) and dials the pre-stored phone numbers.
Register in the control panel
Enter Connection Mode on the control panel. Push the button “#”, and then push “1” on the
control panel.
Press any button on the remote control to register it to the control panel
Specifications
Power supply: DC 3V (CR2025 button battery x1)
Static current: 10 uA
Operating current: ≤7 mA
Transmission distance: ≤ 80 m (in open area)
Radio-frequency: 433MHz (±75KHz)
Housing material: ABS plastic
Operating conditions: Temperature: -10°C~+55°C
Relative Humidity: ≤80% (non-condensing)
Dimensions: 57 x 31 x 11 mm
3.2.2 Wireless Motion Detector
Features
The high performance wireless motion detector is boasting a digital dual-core fuzzy logic
infrared control chip with intelligent analysis. This technology identifies interferences created
by body motion and reduces the false alarm rate.
With automatic temperature compensation and anti-air turbulence technology, it easily adapts
to environmental changes.
Design
1. LED indicator
2. Detection window
3. Bracket
PCB Layout
English Translation
LED working Indicator LED working Indicator
Antenna Antenna
Alarm zone Setup Alarm zone Setup
Tamper switch* Tamper switch*
Infrared sensor** Infrared sensor**
AA 1.5V LR6 AA 1.5V LR6
*Tamper switch
When the alarm system is armed, the tamper switch will trigger the alarm if the case is opened.
Loading...