Denver DVBC-122CI User Manual

Important safety instructions to be kept with the product

Please read attentively

To prevent fire and electric shock, do not expose this receiver to rain or moisture. In order to avoid any possible risk of electric shock, never attempt to open the unit. In case of breakdown, reparation should be made by qualified technicians. No part of this unit should be re

aired by users.

WARNING! Presence of dangerous tension inside apparatus! Do not open. Risk of electric shock! No part should be repaired by users. The maintenance of the receiver should be carried out exclusively by qualified persons.

If the power cord is damaged, it must be replaced or repaired by the manufacturer, its after-sales service, qualified electrician or persons of similar qualification in order to avoid possible danger.

The product must be installed in accordance with national regulations.

The used batteries must be disposed of safely. Throw them in collection bins provided is prohibited (inquire after your retailer for more details) in order to protect the environment.

Proper Installation

- Place the receiver on a flat, firm and stable surface. Do not put it on a carpet or rug.

- Do not place the receiver on top of another device, such as an amplifier. This may lead to overheating.

- Do not put anything above the unit (for example, CDs or magazines).

Sufficient Ventilation

- Place the receiver in a well-ventilated location to prevent accumulation of internal heat. Allow a gap of at least 10cm to the rear and the top of the unit, as well as a space of 5cm to both sides to avoid overheating.

- Do not obstruct any ventilation openings with items such as newspapers, tablecloths, curtains, etc.

Protecting the Receiver from High Temperatures, Humidity, Water and Dust

- The receiver should not be exposed to dripping water or splashing.

- No objects filled with liquids, such as vases, shall be placed on the unit.

- Do not place any objects that might damage your unit near it (e.g. liquid filled objects or candles).

- Do not place any source of flames such as lit candles on the receiver.

- This receiver is to be used in a temperate climate and should not be used in a tropical climate.

Electricity Supply

- Please unplug the receiver in case of prolonged non-use.

- If the power cord is damaged, it must be replaced or repaired by the manufacturer, its after-sales service, qualified electrician or similar qualifications to those to avoid possible danger.

- This device must be connected to a 230V ~ 50Hz electrical network.

- The plug must remain readily accessible after the installation of the product.

Welcome Section Congratulations on choosing to buy a DENVER product. By doing so you now have the

assurance and peace of mind that comes with purchasing a product made by one of the leading manufactory.

Main features：

z Slim size (230mm) z MPEG-2, MPEG-4(H.264) decoding z USB2.0 for software update , music ,image, movie and recording z LCN(Logical Channel Number) supported; z Parental control z Favorite lists z Timer z EPG/TXT/SUBTITLE supported z Digital sound through COAXIAL output (S/PDIF) z PVR ready supported z CI: Common Interface, to decode digital cable pay TV channels

Automatic Standby: the STB preset to automatically switch from active mode into standby if 3 hours no interaction and/or channel change from user, with alert message 2 minutes before going into standby. User can choose OFF (turn off this function) or other hours.

1. Installation of STB ....................................................................................................... 2

1.1 Front Panel ....................................................................................................... 2

1.2 Rear Panel ........................................................................................................ 2

1.3 Connection ....................................................................................................... 3

1.4 Remote ............................................................................................................. 4

2. Installation Guide ........................................................................................................ 5

3. Basic Operation ........................................................................................................... 5

3.1 Program ............................................................................................................ 5

3.2 Picture .............................................................................................................. 6

3.3 Channel Search ................................................................................................ 7

3.4 Time ................................................................................................................. 8

3.5 Option ............................................................................................................... 8

3.6 System ............................................................................................................. 8

3.7 USB .................................................................................................................. 9

3.8 Audio key ........................................................................................................ 10

3.9 TV Channel and radio Channel list ................................................................. 11

4. Other functions introduction .................................................................................... 11

4.1 Program information ....................................................................................... 11

4.2 Favorite List .................................................................................................... 11

4.3 Volume Control ............................................................................................... 12

4.4 Record program .............................................................................................. 12

5. Troubleshooting ........................................................................................................ 13

1. Installation of STB

1.1 Front Panel

1. Power: Switch between Standby mode and active mode.

2. CH+/CH-:

3. on/off: Power lamp, red color in Standby mode, green color in active mode

4. IR sensor: Receive the remote control signal.

5. CI: Common Interface, to decode digital cable pay TV channels, Open the CI slot

door on lower part of the front panel from right side, insert CAM module into CI slot correctly, insert smart card into the CAM module correctly. CAM module and smart card are not included, please contact your local TV provider for their information. Without them, you only can watch free to air digital cable TV channels.

Channel +/-,Move cursor up/down

1.2 Rear Panel

1. CABLE IN

Connect cable signal.

2. LOOP OUT To connect to TV.

3. AUDIO Right and Left

These connectors give you the possibility to connect the audio signal to an external amplifier, or the audio input of your TV.

4. CVBS

This connector has a constant video signal for additional VCR-connections.

5. S/PDIF

Digital audio signal output

6.TV SCART Connector Use this connector to connect your receiver to your video recorder using a SCART cable. Your video signal will now be looped through your receiver to your TV set.

7. HDMI

Connecting to the HDMI input on the TV set.

8. USB

It is used for playing wma,m4a, aac, JPEG,BMP,PNG,AVI, XVID,MKV and USB PVR(USB stickers, mobile HDD with external power supply and FAT32 format).

USB harddisc on products with PVR function:

Please notice that we recommend using a hard disc with OWN power supply on this unit. This is to ensure that it has enough power to work properly. You can buy many hard discs without power supply, but our experience is that they need too much power to work stable. MAXIMUM power for hard discs without power supply is 500mAh.. If they use more than this, they will fail when recording.

9. Power Cord

1.3 Connection

Note: Before connect this STB to other devices, please close all devices’ power.

1.3.1 Connecting to cable signal

To receive the broadcast signal, the cable signal should be connected to the CABLE IN connector at the back of the receiver.

1.3.2 Connecting to TV

1. Connect the Audio Left, Right and VIDEO RCA connectors at the back of the receiver to the Audio Left, Right IN and VIDEO connectors on your TV set.

2. Connect the HDMI connector at the back of the receiver to the HDMI connector on your TV set.

1.3.3 Connecting to Digital Audio Amplifier

Connect COAXIAL connector at the back of your receiver to appropriated input of your Digital Audio

+ 11 hidden pages