Denon DBP-1610 Service Manual

e

D&M Holdings lnc.

Copyright 2009 D&M Holdings Inc. All rights reserved.

WARNING: Violators will be prosecuted to the maximum extent possible.

Ver. 2

●

For purposes of improvement, specifications and design are subject to change without notice.

●

Please use this service manual with referring to the operating instructions without fail.

●

Some illustrations using in this service manual are slightly different from the actual set.

Please refer to the
MODIFICATION NOTICE.

SERVICE MANUAL

MODEL JP E3 E2 EK E2A E1C E1K EUT

DBP-1610

3

BLU-RAY DISC/DVD VIDEO PLAYER

X0430V02DM/DG0910

SAFETY PRECAUTIONS

The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis

resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power

cord is less than 460 kohms, the unit is defective.

LASER RADIATON

Caition - Class 1M visible and invisible laser radiation when open.

Do not view directly optical instruments.

CAUTION

Please heed he points listed below during servicing and inspection.

Heed the cautions!

Spots requiring particular attention when servicing, such

as the cabinet, parts, chassis,etc., have cautions indicated

on labels. be sure to heed these causions and the cautions

indicated in the handling instructions.

Caution concerning electric shock!

(1) An AC voltage is impressed on this set, so touching

internal metal parts when the set is energized could

cause electric shock. Take care to avoid electric

shock, by for example using an isolating transformer

and gloves when servicing while the set is energized,

unplugging the power cord when replacing parts, etc.

(2) Tere are high voltage parts inside. Handle with extra

care when the set is energized.

Caution concerning disassembly and

assembly!

Through great care is taken when manufacturing parts

from sheet metal, there may in some rare cases be burrs

RQWKHHGJHVRISDUWVZKLFKFRXOGFDXVHLQMXU\LI¿QJHUV

are moved across them. Use gloves to protect your hands.

Only use designated parts!

The set's parts have specific safety properties (fire

resistance, voltage resistance, etc.). For replacement parts,

be sure to use parts which have the same poroperties. In

particular, for the important safety parts that are marked

z

on wiring diagrams and parts lists, be sure to use the

designated parts.

Be sure to mount parts and arrange the wires

as they were originally!

For safety seasons, some parts use tape, tubes or other

insulating materials, and some parts are mounted away

from the surface of printed circuit boards. Care is also

taken with the positions of the wores omsode amd clamps

are used to keep wires away from heating and high voltage

parts, so be sure to set everything back as it was originally.

◎

◎

◎

◎

◎

Inspect for safety after servicing!

Check that all screws, parts and wires removed or

disconnected for servicing have been put back in their

original positions, inspect that no parts around the area that

has been serviced have been negatively affected, conduct

an inslation check on the external metal connectors and

between the blades of the power plug, and otherwise

check that safety is ensured.

(Insulation check procedure)

Unplug the power cord from the power outlet, disconnect

the antenna, plugs, etc., and turn the power switch on.

Using a 500V insulation resistance tester, check that the

inplug and the externally exposed metal parts (antenna

terminal, headphones terminal, input terminal, etc.) is

0ȍRUJUHDWHU,ILWLVOHVVWKHVHWPXVW EHLQVSHFWHGDQG

repaired.

◎

Many of the electric and structural parts used in the set

have special safety properties. In most cases these

properties are difficult to distinguish by sight, and using

replacement parts with higher ratings (rated power and

withstand voltage) does not necessarily guarantee that

safety performance will be poreserved. Parts with safety

properties are indicated as shown below on the wiring

diagrams and parts lists is this service manual. Be sure to

replace them with parts with the designated part number.

(1) Schematic diagrams ......Indicated by the zmark.

(2) Parts lists ......Indicated by the z mark.

Using parts other than the designated

SDUWVFRXOGUHVXOWLQ HOHFWULF VKRFN ¿UHV

or other dangerous situations.

Concerning important safety
parts

CAUTION

2

DBP-1610

DIMENSION s

300.4

225

183

309.3

62.2(2)

70

(91)

46.5

140.8

(139)

435

342

15

106

3

DBP-1610

WIRE ARRANGEMENT

If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly
as they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.

Wire arrangement viewed from the top

4

DBP-1610

SPECIFICATIONS

5

DBP-1610

6

DBP-1610

LASER BEAM SAFETY PRECAUTIONS

This BD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.

Location: Inside Top of BD mechanism.

Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

7

DBP-1610

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and
wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified
values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across the terminals of load Z.
See Fig. 2 and the following table.

Table 2: Leakage current ratings for selected areas

Note:This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Clearance Distance (d), (d’)

120 V

t

3mm(d)

t

4mm(d’)

AC Line Voltage Load Z Leakage Current (i)

One side of power cord plug

prongs (B) to:

120 V

2k:RES.

Connected in

parallel

id0.7mA AC Peak

id2mA DC

RF or

Antenna terminals

50k: RES.

Connected in

parallel

id0.7mA AC Peak

id2mA DC

A/V Input, Output

Chassis or Secondary Conductor

Primary Circuit

Fig. 1

d' d

Fig. 2

AC Voltmeter
(High Impedance)

Exposed Accessible Part

B

One side of
Power Cord Plug Prongs

Z

DBP-1610

8

STANDARD NOTES FOR SERVICING

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is
indicated as shown.

2. For other ICs, pin 1 and every fifth pin are
indicated as shown.

3. The 1st pin of every male connector is indicated as
shown.

Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.

2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an
angle.

Pb (Lead) Free Solder

When soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while
applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.

2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)

Top View

Out

In

Bottom View

Input

5

10

Pin 1

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Fig. S-1-1

9

DBP-1610

3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Hot-air
Flat Pack-IC
Desoldering
Machine

CBA

Flat Pack-IC

Tweezers

Masking
Tape

Fig. S-1-2

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine Tip
Soldering Iron

Sharp
Pin

Fig. S-1-4

10

DBP-1610

With Iron Wire:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.

2. Installation

1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.

2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.

To Solid
Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine Tip
Soldering Iron

CBA

Flat Pack-IC

Tweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-IC
is indicated by a " " mark.

Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

11

DBP-1610

Instructions for Handling Semi­conductors

Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 M:) that is
properly grounded to remove any static electricity that
may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate
with proper grounding (1 M:) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.

<Incorrect>

CBA

Grounding Band

Conductive Sheet or
Copper Plate

1MΩ

1MΩ

<Correct>

CBA

12

DBP-1610

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart

This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.

2. Disassembly Method

Note:

(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)

(5) Refer to “Reference Notes.”

About tightening screws

When tightening screws, tighten them with the
following torque.

ID/

Loc.

No.

Part

Removal

Fig.

No.

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

Note

[1] Top Cover D1 9(S-1) ---
[2] Tray Panel D2 --------------- 1

[3]

Front
Assembly

D2

*5(L-1), *3(L-2),
9(S-2), *CN2002

2

[4]

Front A
CBA

D2 *CN3001 ---

[5]

Front B
CBA

D2 --------------- ---

[6]

Front
Bracket

D3 7(S-3), (S-4) ---

[7]

SD CBA

D3 2(S-5), *CN5001 ---

[8] Rear Panel D4

5(S-6), (S-7), 2(S-8),
(S-9), (S-10), 8(S-11),
2(S-12), *CN1006

---

[9]

Motor DC
Fan

D4 --------------- ---

[10]

Inlet CBA

D4 *CN1001 ---

[3] Front

Assembly

[1] Top Cover

[2] Tray Panel

[8] Rear Panel

[13] Video CBA

[14] AV PCB
Bracket

[16] Loader
Bracket

[9] Motor
DC Fan

[10] Inlet CBA

[11] Remote
Jack CBA

[6] Front Bracket

[15] BD Main CBA
& BD Mechanism
Assembly

[7] SD CBA

[18] Power
Holder

[17] Power
Supply CBA

[12] Audio CBA

[4] Front A CBA

[5] Front B CBA

[11]

Remote
Jack CBA

D4 *CN5501 ---

[12] Audio CBA D5

6(S-13), *CN2005,
*CN2007, *CN2008

---

[13] Video CBA D6 4(S-14), *CN7101 ---

[14]

AV PCB
Bracket

D6 4(S-15) ---

[15]

BD Main
CBA & BD
Mechanism
Assembly

D6

4(S-16), *CN6001,
*CN7601

3

[16]

Loader
Bracket

D6 6(S-17) ---

[17]

Power
Supply
CBA

D7 2(S-18), 2(S-19)---

[18]

Power
Holder

D7 3(S-20) ---

p

(1)

p

(2)

p

(3)

p

(4)

p

(5)

Torque

0.45 ± 0.05 N·m

ID/

Loc.

No.

Part

Removal

Fig.

No.

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

Note

13

DBP-1610

Reference Note

1. How to remove tray panel

1) Connect the wall plug to an AC outlet and press
the [ A] button to open the tray.

2) To lift up, the tray panel is removed.

3) Press the [ A] button again to close the tray.

4) Press the [ON/STANDBY] button to turn the
power off.

5) Unplug an AC cord.

2. CAUTION: Locking Tabs (L-1) and (L-2) are
fragile. Be careful not to break them.

3. The BD Main CBA & BD Mechanism Assembly

is adjusted as a unit at factory. Therefore, do
not disassemble it. Replace the BD Main CBA
& BD Mechanism Assembly as a unit.

[1] Top Cover

(S-1)

(S-1)

(S-1)

Fig. D1

[4] Front A CBA

[5] Front B
CBA

[3] Front Assembly

[2] Tray Panel

(S-2)

(S-2)

CN2002

(L-1)

(L-1)

(L-2)

CN3001

Fig. D2

[6] Front Bracket

[7] SD CBA

CN5001

(S-3)

(S-4)

(S-5)

(S-3)

Fig. D3

14

DBP-1610

[8] Rear Panel

[9] Motor DC Fan

[10] Inlet CBA

[11] Remote
Jack CBA

CN1001

CN1006

(S-6)

(S-6)

(S-12)

(S-9)

(S-8)

(S-7)

(S-6)

(S-10)

(S-11)

(S-11)

(S-6)

CN5501

Fig. D4

[12] Audio CBA

CN2007

CN2008

CN2005

(S-13)

Fig. D5

[13] Video CBA

[14] AV PCB Bracket

[15] *BD Main CBA
& BD Mechanism
Assembly

[16] Loader
Bracket

* See Reference Notes 3.

CN7101

CN6001

(S-14)

(S-15)

(S-16)

(S-17)

CN7601

Fig. D6

[17] Power Supply
CBA

[18] Power Holder

(S-18)

(S-20)

(S-19)

Fig. D7

15

DBP-1610

3. How to Eject Manually

1. Remove the Top Cover.

2. Insert a screwdriver, etc. into the straightly so that the Portion A is pushed.

3. Pull the tray out manually and remove a disc.

Screwdriver,
hexagon wrench

Portion A

16

DBP-1610

HOW TO INITIALIZE THE BLU-RAY DISC PLAYER

To put the program back at the factory-default,
initialize the BD player as the following procedure.

1. Turn the power on.

2. Remove the disc on the tray and close the tray.

3. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. a appears on the screen.

Fig. a

4. Press [ C ] button on the remote control unit.
Fig. b appears on the screen and Fig. c appears
on the VFD.

Fig. b

Fig. c

5. To exit this mode, press [POWER OFF] button.

"

*******

" differ depending on the models.

F/W Name
Version
Region

Version Info

: *******
: *.***
: *-*

EXIT <POWER>EEPROM CLEAR <STOP>

"

*******

" differ depending on the models.

F/W Name
Version
Region

Version Info

: *******
: *.***
: *-*

EXIT <POWER>EEPROM CLEAR <STOP>

EEPROM CLEAR : OK

17

DBP-1610

FIRMWARE RENEWAL MODE

Note: The file extension of the available firmware is

“b20”.

1. Turn the power on and remove the disc on the tray
and close the tray.

2. To put the BD player into version up mode, press
[9], [8], [7], [6], and [POP UP MENU/MENU]
buttons on the remote control unit in that order.
The tray will open automatically.
Fig. a appears on the screen and Fig. b appears
on the VFD.

Fig. a Version Up Mode Screen

Fig. b VFD in Version Up Mode

3. Load the disc for version up.

4. The BD player enters the F/W version up mode
automatically. Fig. c appears on the screen and
Fig. d appears on the VFD. Make sure to insert the
proper F/W for the state of this model.

Fig. c Programming Mode Screen (Example)

Fig. d VFD in Programming Mode (Example)

The appearance shown in (*1) of Fig. c is
described as follows:

Fig. e VFD in Vresion Up Mode

5. After programming is finished, the checksum on
the VFD (Fig. f).

Fig. f

VFD upon Finishing the Programming Mode (Example)

Checksum appears on the VFD then the tray will
open automatically. Remove the disc on the tray.

At this time, no button is available.

6. Unplug the AC cord from the AC outlet. Then plug
it again.

7. Turn the power on.

8. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. g appears on the screen.

Fig. g

F/W VERSION UP MODE F/W Name: ******* Ver. *.***

Please insert a Disc

for F/W Version Up

"

*******

" differs depending on the models.

1. ALL

Now Loading...

Ver. *.*** ************A*.b20

(*1)

"

*******

" differs depending on the models.

F/W VERSION UP MODE F/W Name: ******* Ver. *.***

EXIT : POWER

No. Appearance State

1 Now Loading... Loading the disc

2 Reading...

Sending files into the
memory.
After reading, automatically
the tray opens.

3 See FL Display

Writing new version data,
the progress will be displayed
as shown in Fig. e.

"

*******

" differ depending on the models.

F/W Name
Version
Region

Version Info

: *******
: *.***
: *-*

EXIT <POWER>EEPROM CLEAR <STOP>

18

DBP-1610

9. Press [ C ] button on the remote control unit.
Fig. h appears on the screen and Fig. i appears on
the VFD.

Fig. h

Fig. i

To exit this mode, press [POWER OFF] button.

"

*******

" differ depending on the models.

F/W Name
Version
Region

Version Info

: *******
: *.***
: *-*

EXIT <POWER>EEPROM CLEAR <STOP>

EEPROM CLEAR : OK

19

DBP-1610

FIRMWARE RENEWAL MODE (Network Update)

1. Press [SETUP] button on the remote control unit in
stop mode.

2. Use [

} / O] button to select “CUSTOM”, then

press [ENTER] button.

3. Use [

} / O] button to select “Other”, then press

[ENTER] button.

4. Use [

X / Y] button to select “Network Update”,

then press [ENTER] button.
Confirmation message will appear.

5. Use [

X / Y] button to select “Yes”, then press

[ENTER] button.
This unit will start checking for the latest firmware
version.

NOTE:

If any error message concerning the network
environment appears, please confirm the
setting of your unit according to the error
message. If you need to change any of your
network environmental setting in order to
execute the update, please contact to the
internet service provider.

6. Confirmation message will appear.
Use [

X / Y] button to select “Yes”, then press

[ENTER] button.
The unit will start downloading the latest firmware
version.

7. When the download completes, confirmation
message will appear.
Press [ENTER] button.
The unit will start updating the firmware version.
It may take a while to complete the updating.
(Please wait until “100%” appears on the front
panel display.)

8. After updating finishes, this unit will restart and
open the disc tray automatically.

How to Verify the Firmware Version

1. Turn the power on.

2. Remove the disc on the tray and close the tray.

3. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. j appears on the screen.

Fig. j

4. To exit this mode, press [POWER OFF] button.

"

*******

" differ depending on the models.

F/W Name
Version
Region

Version Info

: *******
: *.***
: *-*

EXIT <POWER>EEPROM CLEAR <STOP>

20

DBP-1610

SERVICE MODE

Service Mode

Note: If some test are performed continuously, any error will occur

1st level 2nd level 3rd level Description

1 MECHA TEST

1 Tray Aging Aging of tray open/close

2 TOC Read TOC reading

3 Heat Run

Tray close -> TT1 playback -> TT10
playback -> Tray open -> Tray close

2 VFD/LED TEST

1 All On

Turning on all VFD
(The power LED lights red)

2 All Off

Turning off all VFD
(The power LED lights green)

3 ERROR RATE

Displaying Error rate
during playback

4 LD TEST

1 LD Power

1 Off Turning off LD

2 BD Turning on BD LD

3 DVD Turning on DVD LD

4 CD Turning on CD LD

2 Operating Time

Displaying LD Operation Time (with
clear function)

5

CHANNEL
TEST

1 TEST TONE

1

Center/Subwoofer/
Front LR

2

Surround LR/
Surround Back LR

2 Front Lch

3 Center

4 Front Rch

5 Surround Rch

6

Surround Back
Rch

7 Surround Back Lch

8 Surround Lch

9 Sub woofer

6 SD CARD TEST

7

DEFAULT
SETTING

Default setting

DBP-1610

21

Entering Service Mode

In power on condition, no discs and tray close, it will be entered into service mode by the following operation using
the remote controller. However, it will not be entered when Media Select Item is SD Memory.

Service Mode by using remote controller

Press the following buttons on the remote controller in power on condition, no discs and tray close;
[2]->[5]->[8]->[0]->[CLEAR]

Release from Service Mode

Press the [POWER OFF] button to turn off power.

Screen saver/Auto Power Off in Service Mode

These functions are not performed in Service Mode.
After entering, Fig. k appears on the screen and Fig. l appears on the VFD.

Fig. k Service Mode (Main Menu)

Fig. I Service Mode

Available button in service mode

Note: Press the number key to select items. Or, press the cursor button (up/down) to select items and press

[ENTER] button.

Button condition

ENTER Enter the next level
POWER OFF Turn the power off (when the service mode is completed)
1~7 Enter the selected item (next level)
OTHER Not available

INDICATION DESCRIPTION REMARK

F/W Name Model Name E5K***D, etc.
Region BD region - DVD region A-1, etc.
Release Ver. Release version D.jpp, etc.

SERVICE MODE

1: MECHA TEST
2: VFD/LED TEST
3: ERROR RATE MEASURE
4: LD TEST
5: CHANNEL TEST
6: SD CARD TEST
7: DEFAULT SETTING

F/W Name :******* Region

:*-*
Release Ver. :*.***
ADSP1/2 Ver. :---/--- PLD Ver. :--­FPGA Ver. :--- I/P Scaler Ver.:---

* Firmware Version differs depending on the
models, and this indication is one example.

22

DBP-1610

TRAY LOCK MODE

Tray Lock Mode prevents the tray opening or closing to
prevent disc theft in demo mode.

Enter this mode using the following procedure.

1. Confirm that the TV Monitor is connected.

2. With playback stopped, press [SETUP], [TOP
MENU], [3], [AUDIO], [0] and [SETUP] buttons on
the remote control unit in that order. "Trade-On"
appears in the upper right corner on the screen,
and Fig. a appears on the VFD for 2 seconds.

Fig. a

3. To exit this mode, press [SETUP], [TOP MENU],
[3], [AUDIO], [0] and [SETUP] buttons on the
remote control unit in that order. "Trade-Off"
appears in the upper right corner on the screen,
and Fig. b appears on the VFD for 2 seconds.

Fig. b

23

DBP-1610

REMOTE LOCK MODE

SETTING MENU:

Remote Lock Off Mode:

This mode receives an input signal from the
remote control unit or from the Remote In-Jack on
the rear panel.

Remote Lock On Mode:

This mode dose not receive an input signal from
the remote control unit or from the Remote In-Jack
on the rear panel.

Perform the setting using the following procedure.

1. Press [POWER ON] and [STOP] buttons on the
front panel simultaneously for over 3 seconds to
set "Remote Lock Mode" and display mode.

2. Press [STILL/PAUSE] button on the front panel to
set to "On" or "Off". When "Remote Lock On",
"Remote Lock On" will appear in the upper right
corner on the screen and appears on the VFD.

Fig. a VFD

When "Remote Lock Off", "Remote Lock Off" will
appear in the upper right corner on the screen and
appears on the VFD.

Fig. b VFD

a. If [STILL/PAUSE] button is not pressed for 2

seconds or any other button is pressed within
2 seconds, the unit will be released from
"Remote Lock Mode".

b. When initializing, set the Remote Lock Mode

"off".

24

DBP-1610

TROUBLESHOOTING

FLOW CHART NO.2

The fuse blows out.

After servicing, replace the fuse.

Check the presence that the primary component
is leaking or shorted and service it if defective.

Check the presence that the rectifying diode or
circuit is shorted in each rectifying circuit of
secondary side, and service it if defective.

FLOW CHART NO.3

When the output voltage fluctuates.

Ye s

No

FLOW CHART NO.4

When buzz sound can be heard in the vicinity of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary
side, and service it if defective. (D1025, D1028, D1030, D1031, D1032, D1033, IC1008, IC1009, IC1010, Q1009,
Q1010, Q1011, Q1013, Q2636)

Does the photo coupler circuit on the secondary
side operate normally?

Check D1021, IC1002, IC1004 and their periphery,
and service it if defective.

Check D1029, IC1004 and their periphery,
and service it if defective.

FLOW CHART NO.5

FL is not outputted.

Is 35V voltage supplied to the emitter of Q2602?

Check D1032, C1033 and periphery circuit,
and service it if defective.

Check Q2601, Q2602, D2603 and their periphery,
and service it if defective.

Check FL-SW line and service
it if defective.

Is the "L" signal outputted to the collector of
Q2603?

Ye s

Ye s

Ye s

No

No

No

FLOW CHART NO.1

The power cannot be turned on.

Is the fuse normal?

Is normal state restored when once unplugged
power cord is plugged again after several seconds?

Is the EV+5V line voltage normal?

See FLOW CHART No.2 <The fuse blows out.>

Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(D1007, D1008, D1011, D1012, D1023, D1024,
IC1002, Q1002, T1002, C1022, R1022)

Check each rectifying circuit of the secondary circuit
and service it if defective.

Ye s

Ye s

Ye s

No

No

No

Is the "H" signal inputted to the base of Q2603?

Replace Q2603.

25

DBP-1610

FLOW CHART NO.6

Is 5V voltage inputted to the emitter of Q1011?

Replace Q1013.

Ye s

No

Is 11V voltage inputted to the base of Q1013? Is 14V voltage inputted to the base of Q1006?

Check D1028, D1041, C1026, L1004

and

their periphery, and service it if defective.

No

FLOW CHART NO.7

FLOW CHART NO.8

P-ON+10.5V is not outputted.

Is 14V voltage inputted to the collector of Q1013?

Ye s Ye s No

Ye s

Check Q1006, D1046,
and their periphery, and
service it if defective.

Check Q1008,

and
PWSW4 line, and
service it if defective.

Is 5V voltage supplied to Pin(3) of IC1009?

Ye s

No

FLOW CHART NO.9

P-ON+1.2V is not outputted.

Is the "L" signal inputted to the base of Q1015?

Ye s

Check IC1009, Q1015

and their periphery, and

service it if defective.

Is 4.5V voltage inputted to the base of Q1011?

Is 4.5V voltage inputted to the base of Q1009?

Replace Q1011.

Ye s

No

Check D1025, D1030, D1031, C1029, C1034 and
their periphery, and service it if defective.

Is 5V voltage inputted to the emitter of Q1009?

Ye s

No

Replace Q1009.

Check Q1007 and PWSW4 line and service it if
defective.

Check Q1007 and PWSW4 line and service it if
defective.

Ye s

No

Check PWSW2 line and service it if defective.

No

No

Check D1025, D1030, D1031, C1029, C1034 and
their periphery, and service it if defective.

Check D1025, D1030, D1031, C1029, C1034 and
their periphery, and service it if defective.

Check D1025, D1030, D1031, C1029, C1034 and
their periphery, and service it if defective.

P-ON+5V (2) is not outputted.

FLOW CHART NO.10

P-ON+3.3V is not outputted.

Is 5V voltage supplied to Pin(1) of IC1008?

ls "L" signal outputted to the collector of Q1005?

Check IC1008, D1040 and their periphery circuit,
and service it if defective.

Ye s

Ye s

No

Check Q1005 and PWSW1 line and service it if
defective.

No

P-ON+5V (1) is not outputted.

26

DBP-1610

FLOW CHART NO.12

Is 15V voltage inputted to the emitter of Q1010?

Ye s

No

FLOW CHART NO.11

Is 14V voltage inputted to the base of Q1010?

Replace Q1010.

Check Q1008 and PWSW4 line and service it if
defective.

Ye s

No

Check D1028, C1026, L1003 and their periphery, and
service it if defective.

Is 5V voltage inputted to Pin(3) of IC1010?

Ye s

No

No

Ye s

Check IC1010, Q1016

and their periphery, and

service it if defective.

Check D1025, D1030, D1031, C1029, C1034
and their periphery, and service it if defective.

P-ON+1.8V is not outputted.

ls "L" signal outputted to the base of Q1016?

P-ON+14.5V is not outputted.

Check PWSW2 line and their periphery, and service it
if defective.

Ye s

No

FLOW CHART NO.14

The key operation is not functioning.

Are the contact point and the installation state of the key
switches (SW3001, SW3101, SW3102, SW3104, SW3106,
SW3108, SW3110-3113) normal?

When pressing each switches (

SW3001, SW3101,

SW3102, SW3104, SW3106, SW3108, SW3110-3113

),

do the voltage of Pin(1, 62) of IC2000 increase?

Check the switches (

SW3001, SW3101, SW3102,

SW3104, SW3106, SW3108, SW3110-3113

) and their

periphery, and service it if detective.

No

Re-install the switches (

SW3001, SW3101, SW3102,

SW3104, SW3106, SW3108, SW3110-3113

) correctly or

replace the poor switch.

Replace IC2000.

Ye s

Ye s

Ye s

Ye s N o

Ye s N o

Ye s

No

No

No

FLOW CHART NO.13

The fluorescent display tube does not light up.

Is 3.3V voltage supplied to Pin(24) of FL3001?

Is 9V voltage supplied to Pin(1,2) of FL3001?

Is 5V voltage supplied to Pin(29,30) of FL3001?

Replace FL3001.

Check the EV+3.3V line and service it if defective.

Is 10V voltage supplied to the emitter of Q2604?

Check D1033, C1028, R1032,
R1033 and their periphery,
and service it if defective.

Check Q2603 and FL-SW

line

and service it if defective.

Replace Q2604.

Is 9V voltage inputted
to the base of Q2604?

Check the F2

line and service it if defective.

27

DBP-1610

Ye s

FLOW CHART NO.16

The disc tray cannot be opened and closed. (It can be done using the remote control unit.)

Is the normal control voltage inputted to Pin(62) of
IC2000?

Refer to "FLOW CHART NO.14" <The key

operation is not functioning.>

Replace the BD Main CBA & BD Mechanism
Assembly.

Replace the "OPEN/CLOSE" switch (SW3101).

No

Check the line between the

RS3001 (remote control

receiver)

and the

Pin(27) of IC2000,

and service it if

defective.

FLOW CHART NO.15

No operation is possible from the remote control unit.(Operation is possible from the unit.)

Replace the RS3001 (remote control receiver) or
remote control unit.

Is the "L" pulse sent out Pin(1) of RS3001 (remote
control receiver) when the remote control unit is activated?

Is the "L" pulse inputted to the Pin(27) of IC2000?

Replace IC2000.

Is 5V voltage supplied to Pin(2) of RS3001
(remote control receiver) ?

Ye s

No

Check EV+5V line and service it if defective.

No

No

Ye s

Ye s

Ye s

FLOW CHART NO.17

The disc tray cannot be opened and closed.
[No Disc] indicated.
Both functions of picture and sound do not operate normally.

Replace the BD Main CBA & BD Mechanism
Assembly.

28

DBP-1610

Is 5V voltage supplied to the Pin(7,21) of IC4000?

Replace IC4000.

Check VIDEO+5V line and
service it if defective.

Are the video signals outputted to each pin of
IC4000?

Ye s

No

Ye s

Ye s

No

IC4000 20PIN VIDEO-Y(I/P)
IC4000 17PIN VIDEO-Pb/Cb
IC4000 15PIN VIDEO-Pr/Cr
IC4000 25PIN VIDEO

Check the periphery of the VIDEO OUT terminal
(JK4002, JK4003, JK4005) from Pin(15,17,20) of
IC4000 and service it if defective.

Check

the periphery of the VIDEO OUT terminal

(JK4004)

from Pin(25) of IC4000

and service it if

defective.

Are the video signals outputted to the specific
output terminal?

Are the component video signals outputted to the
VIDEO OUT terminal (JK4002, JK4003, JK4005)?

No

No

Are the composite video signals outputted to
the VIDEO OUT terminal (JK4004)?

FLOW CHART NO.18

Picture does not appear normally.

Set the disc on the disc tray, and playback.

Are the video signals outputted to each pin of
CN4000?

Replace the BD

Main CBA & BD Mechanism

Assembly.

Check the line between each pin of CN4000 and
each pin of IC4000, and service it if defective.

CN4000 3PIN → IC4000 3PIN VIDEO
CN4000 5PIN → IC4000 8PIN VIDEO-Y(I/P)
CN4000 7PIN → IC4000 10PIN VIDEO-Pb/Cb
CN4000 9PIN → IC4000 12PIN VIDEO-Pr/Cr

Are the video signals shown above inputted into
each pin of IC4000?

Ye s

No

No

CN4000 3PIN VIDEO
CN4000 5PIN VIDEO-Y(I/P)
CN4000 7PIN VIDEO-Pb/Cb
CN4000 9PIN VIDEO-Pr/Cr

IC4000 3PIN VIDEO
IC4000 8PIN VIDEO-Y(I/P)
IC4000 10PIN VIDEO-Pb/Cb
IC4000 12PIN VIDEO-Pr/Cr

29

DBP-1610

FLOW CHART NO.19

Audio is not outputted normally. (JK2200, JK2201)

Set the disc on the disc tray, and playback.

Is the signal at Pin(24) of IC2000 "H" ?

Are the analog audio signals outputted to each pin
of CN2007?

Is the "H" level mute signal outputted to CN2007?

CN2007 22PIN AUDIO(L)
CN2007 24PIN AUDIO(R)

CN2007 19PIN AUDIO(L)-MUTE
CN2007 20PIN AUDIO(R)-MUTE

IC2200 7PIN AUDIO(L)
IC2200 1PIN AUDIO(R)

IC2200 6PIN AUDIO(L)
IC2200 2PIN AUDIO(R)

Replace the BD

Main CBA & BD Mechanism

Assembly.

Replace the BD

Main CBA & BD Mechanism

Assembly.

Replace IC2200.

Check the periphery between Pin(1,7) of IC2200
and the audio terminal (JK2200, JK2201), and
service it if detective.

Check each line between each pin of CN2007
and each pin of IC2200, and service it if detective.

CN2007 22PIN → IC2200 6PIN AUDIO(L)
CN2007 24PIN → IC2200 2PIN AUDIO(R)

Are the analog audio signals inputted to each pin
of IC2200?

Are the analog audio signals outputted to each pin
of IC2200?

Are the audio signals outputted to the audio
terminal (JK2200, JK2201)?

Ye s

Ye s

Ye s

Ye s

Ye s

No

Check

AUDIO-MUTE line, and

service it if

detective.

No

No

No

No

No

30

DBP-1610

BD Mechanism Replacement Guidelines

The guidelines describe how to determine whether a BD Mechanism Assembly is defective or not.
Confirm that the malfunction is eliminated after replacing the defective BD Mechanism Assembly with a new one.

*The BD Mechanism Assembly shall be acceptable when the following test disc can be played successfully;

*Select [4: LD Test] and select [2: Operating Time] in Service Mode.
If the Operating Time shows 3,000 hours or more, the BD Mechanism Assembly shall be determined that it has
reached the end of its life.

BD-ROM BLX-201S3(SONY) chp12

BD Main CBA
& BD Mechanism Assembly

Replacement of BD Main CBA & BD Mechanism Assembly

1. Remove the Top Cover, Tray Panel, Front Assembly, Front Bracket, Video CBA and AV PCB Holder.

2. Disconnect Connectors and replace the BD Main CBA & BD Mechanism Assembly.
Refer to CABINET DISASSEMBLY INSTRUCTIONS.

31

DBP-1610

BLOCK DIAGRAMS

System Control Block Diagram

FAN-CONT1

IC2000

IC6903 (EEPROM)

IC6001

(SUB MICRO CONTROLLER)

1

19 20 21 22

CN2002 CN3002

FL3001

VFD

15 15KEY-2

16 16KEY-1

12 12REMOTE

66FL-RESET

55FL-STB

44FL-SCL

33FL-SDA

XRST

XTRST

CN4001

CN2005

10 10SUB-TXD

99SYS-RESET

11 11SUB-RXD

18 18

STANDBY/POWER

-LED

D3003

POWER

FRONT A CBA

BD MAIN CBA

AUDIO CBA

RS3001

REMOTE

SENSOR

274934

33

3

60

14

8

9

RESET

15

SUB-TXD

16

AE32

T34

SUB-RXD

28 CEC-IN

CEC

30

CEC-OUT

13

MUTE2

PWSW1

STANDBY/POWER-LED

SYS-RESET

V32

TXD1

U34

V31

W30

K2

J2J1J3

J4

G5

F4

H5

G4

H4

RXD1

SCL0

SDA0

MII-RXD3

MII-RXD2

MII-RXD1

MII-RXD0

MII-RXCLK

MII-TXD3

MII-TXD0

MII-TXCLK

MII-TXD2

MII-TXD1

SCL

SDA

FL-SDA

FL-SCL

FL-STB

50

FL-RESET

REMOTE

KEY-2

62

KEY-1

OSC2

OSC1

8MHz

X'TAL

X2000

EV+3.3V

IC2001

RESET

BUFFER

Q2619

JK7501

Q6701

Q6702

FL-SW

MUTE1

TO VIDEO

BLOCK

DIAGRAM

24

AUDIO-MUTE

AUDIO-MUTE

TO AUDIO

BLOCK

DIAGRAM

IC6401

(ETHERNET INTERFACE)

5

6

P-ON+1.8V

RESET

IC6701

2 1

D3002

STANDBY

BUFFER

Q2618

SWITCHING

Q2620, Q2621

CN3001

CN3101

1

KEY-2

1

2

KEY-1

2

FRONT B CBA

KEY

SWITCH

KEY

SWITCH

POWER

SW3001

EV+3.3V

BUFFER

Q2002

PWSW2

32 FL-SW

CN5501

CN4002

11

REMOTE

REMOTE JACK CBA

REMOTE

-IN

REMOTE

-OUT

JK5550

Q5551, Q5552

15 15MUTE1

14 14MUTE2

66

REMOTE

21 MUTE1

22 MUTE2

17 17CEC

4

3

1

2

IC5550

(PHOTO COUPLER)

VIDEO CBA

14 14SUB-TXD

15 15SYS-RESET

13 13SUB-RXD

17 17CEC

39

ETHERNET

INTERFACE

383635

33

2823222120

121110

9

RX(-)

JK6401

ETHERNET

JACK

RX(+)

TX(-)

TX(+)

123

6

MAIN MICRO

CONTROLLER

CN4000

PWSW4

FAN-LOCK

TO POWER

SUPPLY

BLOCK

DIAGRAM

25

4

PWSW1

FAN-CONT1

44

PWSW237PWSW463FAN-LOCK

CN7101

BUFFER

32

DBP-1610

Digital Signal Process 1 Block Diagram

BD MECHANISM

BD MAIN CBA

W1

V2

U3

HU(+) 5

HU(-) 6

HV(+) 7

HV(-) 8

HW(+) 9

HW(-) 10

HB(-) 11

CN603

IC6001 (MAIN MICRO CONTROLLER/DIGITAL SIGNAL PROCESS)

IC603 (MOTOR DRIVE)

IC604 (OP AMP)

TRACKING

ACTUATOR

DRIVE

OEIC

(CD/DVD)

IC602 (MOTOR DRIVE)

IC603 (MOTOR DRIVE)

IC601 (MOTOR DRIVE)

IC201 (FRONT-END PROCESSOR)

FE

DIGITAL

SIGNAL

PROCESS

STREAM

CONTROL

COPY

PROTECT

AACS

BD+

CSS

CPRM

MATRIX

RF

GENERATOR

D22

B22

A24

E23

M32

M31

J34

J33

102-105

97-100

242119131415161718

SLD2(+) 4

SLD2(-) 3

SLD1(+) 2

SLD1(-) 1

CN601

LOAD(+) 5

LOAD(-) 6

TRAY-OUT 2

TRAY-IN 1

INLIMIT 4

CN602

TD 3

TR 4

FD1 1

FR1 2

EXPA(+) 9

EXPA(-) 7

EXPB(+) 10

EXPB(-) 8

A-D 21-24

E-H 26-29

RF(+) 17

RF(-) 18

BDRF(+) 14

BDRF(-) 15

SD ATA 2 40

SD ATA 1

SCLK1

SD ATA 2

SD ATA 1

SCLK2

SCLK1

SCLK2 38

CN101

CN101

32

33

2

1

236

5

212019

18

LOADING

MOTOR DRIVE

14

15

COLLIMATE

LENS

MOTOR DRIVE

SLED

MOTOR DRIVE

SPINDLE

MOTOR

DRIVE

12

FOCUS 1

ACTUATOR

DRIVE

TRACKING-CONTROL

TO DIGITAL SIGNAL

PROCESS 2 BLOCK

DIAGRAM

(IC6001)

FOCUS1-CONTROL

FOCUS2-CONTROL

SLED1-CONTROL

SLED2-CONTROL

TRAY-OUT

TRAY-IN

INLIMIT

SPINDLE-CONTROL

SPINDLE-FG

LOAD-CONTROL

EXPA-CONTROL

EXPB-CONTROL

22

83 78 79

17

16

FOCUS 2

ACTUATOR

DRIVE

12

132310

D24

C24

4

30

C22

D21

E21

B3

13

E24

10

B25

4

107-110

868588

87

G34

61 WBL

H34

B28

59

20 SE02

ASENV

A28

18 SE01

B34

C33

66

655453

RF

EQUALIZER

WOB

/LPP

MPX

1 2

7 6

8 9

D23

OEIC

(BD)

LASER

DIODE

DRIVE

SLED

MOTOR

TRAY-OUT

TRAY-IN

INNER

SW

SPINDLE

MOTOR

FD2 6

FR2 5

LOADING

MOTOR

VIDEO SIGNAL AUDIO SIGNAL

33

DBP-1610

Digital Signal Process 2 Block Diagram

BD MAIN CBA

ED (0-7)

C0DQ (0-31)

C0A (0-12)

C1DQ (0-31)

C1A (0-12)

MEDIA

PROCESSOR

Java (BD-J)

MPEG-2

DiVX

VC-1

H.264

DECODER

HD (TS)

SD (PS)

TO

DIGITAL

SIGNAL

PROCESS 1

BLOCK

DIAGRAM

(IC6001)

CN7601

MEMORY

I/F

SD I/F

IC6001 (MAIN MICRO CONTROLLER/DIGITAL SIGNAL PROCESS)

IC6703 (CLOCK GENE.)

AH34

C15

A2B6B5

IC6902

(NAND FLASH MEMORY)

NAND FLASH

MEMORY (64M x 8bit)

(DDR2 SDRAM)

IC6501,IC6502

DDR2 SDRAM

(1Gbit )

(DDR2 SDRAM)

IC6601,IC6602

DDR2 SDRAM

(512Mbit)

A4,A8,A9,B4,B9,C5,C9,

C11,D8,D10,E10,E11

A3,A6,A7,B7,C4,C6,C7,

C8,D6,D9,E8,E12

AF32,AG34,

AH33,AJ34

I/P CONVERTER

/SCALING

DIGITAL

VIDEO

OUT

DIGITAL

AUDIO

OUT

VIDEO

DAC

CLK

VSYNC

HSYNC

BP1-P-CLK

BP1-VSYNC

BP1-HSYNC

SDCLK

SD DATA(0-3)

TO

VIDEO

BLOCK

DIAGRAM

VIDEO

SCL3

33M CLOCK

33M CLOCK

74M CLOCK

27M CLOCK

768K CLOCK

SCL

SDA3

HDMI-DATA0

HDMI-DATA1

HDMI-DATA2

HDMI-DATA3

HDMI-MCK

HDMI-BCK

HDMI-LRCK

HDMI-SPDIF

MC

MD

DAC-SCK

DAC-BCK

DAC-LRCK

MS1

DATA

SPDIF

X6701

27MHz

OSC

CLOCK

GENE.

SDA

TO

AUDIO

BLOCK

DIAGRAM

VIDEO SIGNAL AUDIO SIGNAL

SCL3

R33

SDA3 U31

C14

B14

A12

D12

B13

AC31

A13

B12

TO

VIDEO

BLOCK

DIAGRAM

E13

AL34

B10

B11

A10

A11

D11

C12

C10

2

3

1

16

789

10

E20

A19

D20

AL5

SD

CARD

SLOT

POWER

SUPPLY CBA

CN5003 CN5004

55SDDAT0

33SDDAT1

15 15SDDAT2

13 13SDDAT3

77SDCLK

SD CBA

CN5000

CN5001

19 19SDDAT0

21 21SDDAT1

99SDDAT2

11 11SDDAT3

17 17SDCLK BP1-CO(0-11)

BP1-Y(0-11)

D18

VIDEO-Y(I/P)

B17

VIDEO-Pb/Cb

F17

VIDEO-Pr/Cr

DBP-1610

34

Video Block Diagram

VIDEO CBABD MAIN CBA

HDMI-DATA0

HDMI-DATA1

HDMI-DATA2

HDMI-DATA3

HDMI-MCK

HDMI-BCK

HDMI-LRCK

HDMI-SPDIF

70-73,75-78,

92,94,102,103

50,51,53-57,59,

87,88,90,91

TO DIGITAL

SIGNAL

PROCESS 2

BLOCK

DIAGRAM

2dB

AMP

LPF

6.75MHz

13.5/37MHz

13.5/37MHz

13.5/37MHz

17

2dB

AMP

LPF

10

15

SCL3

SDA3

TO SYSTEM

CONTROL

BLOCK

DIAGRAM

MUTE1

2dB

AMP

LPF

MUTE1

MUTE2

12

VIDEO-Pb/Cb

OUT

VIDEO-Y

OUT

VIDEO-Pr/Cr

OUT

JK4004

JK4005

C4018

8 20

T.M.D.S DATA2-

T.M.D.S DATA2+

T.M.D.S DATA1-

T.M.D.S DATA1+

T.M.D.S DATA0-

T.M.D.S DATA0+

T.M.D.S CLOCK+

T.M.D.S CLOCK-

JK7501

HDMI-CONNECTOR

DDC DATA

DDC CLOCK

HOT PLUG

DETECT

IC7501 (HDMI INTERFACE)

REGISTER

IIC

I/F

VIDEO

I/F

DDC

I/F

AUDIO
I/F

HDCP
CIPHER/
ENCRYPTOR

TMDS
ENCODER

AV
CONTROLLER

TMDS
SERIALIZER

46454442413936

35

23251921151713

11

113

116

118

120

119

VIDEO SIGNAL AUDIO SIGNAL

CLK

CN4000CN7101

VS

HS

121

83

84

JK4002

JK4003

IC4000 (VIDEO DRIVER)

4dB

AMP

4dB

AMP

4dB

AMP

4dB

AMP

LPF 25

2dB

AMP

75Ω

DRIVER

75Ω

DRIVER

75Ω

DRIVER

75Ω

DRIVER

MUTE2

3

VIDEO OUT

(COMPOSITE)

TO DIGITAL

SIGNAL

PROCESS 2

BLOCK

DIAGRAM

2

13

WF1 WF2

WF3

55VIDEO-Y(I/P)

77VIDEO-Pb/Cb

99VIDEO-Pr/Cr

33VIDEO

191516

31649

7

10

12

BP1-CO(0-11)

BP1-Y(0-11)

VIDEO

VIDEO-Y(I/P)

VIDEO-Pb/Cb

VIDEO-Pr/Cr

BP1-HSYNC

BP1-VSYNC

BP1-P-CLK

AUTHENT

/CATION

KEY

EXCHANGE

35

DBP-1610

Audio Block Diagram

AUDIO CBA

BD MAIN CBA

AUDIO SIGNAL

WF4

TO SYSTEM CONTROL

BLOCK DIAGRAM

AUDIO-MUTE

VIDEO CBA

11 11SPDIF

CN7101 CN4000

DIGITAL

AUDIO OUT

(COAXIAL)

SPDIF

JK4000

(REAR)

BUFFER

Q4006

WF5

IC7001

(AUDIO D/A CONVERTER)

AUDIO

DAC

3458276

(L-CH)

(R-CH)

1

R-CH

MUTE

L-CH

MUTE

16

14

15

AUDIO(L)-

OUT

AUDIO(R)-

OUT

Q2203

MUTE-ON

Q2202

MUTE-ON

Q2200

DRIVE

Q2201

DRIVE

JK2200 (REAR)

JK2201 (REAR)

IC2200

(OP AMP)

7

1

6

2

22 22AUDIO(L)

24 24AUDIO(R)

19 19AUDIO(L)-MUTE

20 20AUDIO(R)-MUTE

CN7001 CN2007

TO DIGITAL

SIGNAL

PROCESS 2

BLOCK DIAGRAM

MCMDDAC-SCK

DAC-BCK

DAC-LRCK

MS1

DATA

36

DBP-1610

Power Supply Block Diagram

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F1001) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,

replace only with the same type fuse.

ATTENTION : Pour une protection continue les risqes

d'Incele n'utiliser que des fusible de même type.

Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

AUDIO CBA

IC1002

HOT

COLD

Q1009

Q1012, Q1014

Q1011

Q1010

Q1013

Q1006

Q1008

Q1007

Q1002

VDD

7

6

T1002

11

12

15

13

10

9

16

14

F1001

2A/250V

LINE

FILTER

L1001

A V

F

3

4

IC1004

ERROR

VOLTAGE DET

1

2

P-ON+14.5V

SHUNT

REG.

D1007, D1008,

D1011, D1012

BRIDGE

RECTIFIER

SWITCHING

CONTROL

5

2

FAN-VCC 1

2FAN-LOCK

CN1006

3,4 P-ON+10.5V

2 P-ON+5V(1)

CN1003

5,6 P-ON+3.3V

17-20

P-ON+1.2V

23 P-ON+5V(2)

9-11

P-ON+1.8V

SW+14.5V

TO BD MAIN

CBA

(CN6001)

F1

F2

TO SYSTEM

CONTROL

BLOCK

DIAGRAM

FL-SW

FL

SW+10.5V

SW+5V

SW+5V

CURRENT

LIMIT

6

1

3

HOT CIRCUIT. BE CAREFUL.

FAN

POWER SUPPLY CBA

Q2604

Q2603

FAN

CONTROL

FAN

CONTROL

Q1019

Q1017

2

4

AC1001

CN1002

CN1001

11

AC120V

22

AC120V

INLET CBA

Q1001

D1029

44F1-IN

66+FL

55F2-IN

CN2008

CN1004

10 10PWSW1

11EV+5V

11 11PWSW2

13 13PWSW4

15 15FAN-CONT1

16 16FAN-LOCK

IC1008

+3.3V

REG.

Q1005

Q2602

Q2601

IC1009

Q1015

+1.2V

REG.

IC1010

+1.8V

REG.

Q1016

FAN-CONT1

PWSW1

PWSW2

PWSW4

FAN-LOCK

Q2636, D2625

+3.3V

REG.

EV+3.3V

AUDIO+3.3V

AC CORD

SWITCHING

CONTROL

37

DBP-1610

---MEMO---

38

DBP-1610

SCHEMATIC DIAGRAMS AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.

Notes:

1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.

2. All resistance values are indicated in ohms
(K = 10

3

, M = 106).

3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.

4. All capacitance values are indicated in PF
(P = 10

-6

PF).

5. All voltages are DC voltages unless otherwise
specified.

39

DBP-1610

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE
SAME TYPE FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER
QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.

3. Note:

1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.

4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:

5. How to read converged lines

6. Test Point Information

A V

F

This symbol means fast operating fuse.
Ce symbole represente un fusible a fusion rapide.

2

3

1

5.0
(2.5)

5.0

The same voltage for
both PLAY & STOP modes

Indicates that the voltage
is not consistent here.

PLAY mode
STOP mode

(Unit: Volt)

3

2

1

ABCD

1-B1

1-D3

AREA D3

AREA B1

1-D3
Distinction Area

Line Number
(1 to 3 digits)

Examples:

1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3".

2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".

: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.

40

DBP-1610

Audio 1/2 Schematic Diagram

41

DBP-1610

Audio 2/2 Schematic Diagram

42

DBP-1610

Video Schematic Diagram

43

DBP-1610

Power Supply & Inlet Schematic Diagram

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

F

A V

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."

44

DBP-1610

Front A & Front B Schematic Diagram

45

DBP-1610

Remote Jack Schematic Diagram

46

DBP-1610

SD Schematic Diagram

47

DBP-1610

BD Main 1/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

48

DBP-1610

BD Main 2/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

49

DBP-1610

BD Main 3/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

50

DBP-1610

BD Main 4/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

51

DBP-1610

BD Main 5/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

52

DBP-1610

BD Main 6/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

53

DBP-1610

BD Main 7/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

54

DBP-1610

BD Main 8/11 Schematic Diagram

55

DBP-1610

BD Main 9/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

56

DBP-1610

BD Main 10/11 Schematic Diagram

57

DBP-1610

BD Main 11/11 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section.

1 NOTE:

58

DBP-1610

WAVEFORMS

WF4

WF1

WF2

WF3

Pin 22 of CN2007

Pin 9 of CN4000

WF5

Pin 11 of CN4000

Pin 7 of CN4000

C4018 PLUS LEAD

20μs0.5VVIDEO-CVBS

VIDEO-Cr 0.2V 10

μ

s

VIDEO-Cb 0.2V 10

μ

s

AUDIO(L) 1V 0.5ms

SPDIF 1V 0.1

μ

s

NOTE:

Input Signal (DVD)
VIDEO: 75% COLOR BAR
AUDIO: 1KHz, 0dB

59

DBP-1610

WIRING DIAGRAM

BD MAIN CBA & BD MECHANISM ASSEMBLY

BD MAIN CBA

RELAY CBA

PICKUP

POWER SUPPLY CBA

SD CBA

CN101CN601

CN602

CN603

HDMI-CONNECTORETHERNET JACK

SD CARD SLOT

30

GND

31

GND

1

SLD1(-)

2

SLD1(+)

3

SLD2(-)

4

SLD2(+)

32

+3.3V

33

GND

34

GND

35

+5V

36

+8V

37

THERMO

38

SCLK2

1

W

2

V

3

U

4

+5V

5

HU(+)

6

HU(-)

7

HV(+)

8

HV(-)

9

HW(+)

10

HW(-)

11

HB(-)

39

SEN-LDD

40

SD ATA 2

41

XREST

42

LDEN

43

NU

44

TEST-V

45

NU

2

FR1

1

FD1

3

TD

4

TR

5

FR2

6

FD2

7

EXPA(-)

8

EXPB(-)

9

EXPA(+)

10

EXPB(+)

11

SA-INT

12

PI-CONT

FAN

BD-OEIC

LENS DRIVE

CD/DVD

-OEIC

CD-LD

BD-LD

PD-LD

DVD-LD

LASER DIODE DRIVE

SPINDLE

MOTOR

M

SLED

MOTOR

M

CN1006

1

FAN-VCC

2

FAN-LOCK

11

TRAY-IN

22

TRAY-OUT

33

GND

44

INLIMIT

55

LOAD(+)

66

LOAD(-)

M

LOADING

MOTOR

TRAY

-IN

INNER

SW

TRAY

-OUT

CN5004

CN5003

CN5001

CN7601

15

WP

14

CD

13

SDDAT1

12

GND

11

SDDAT0

10

GND

9

SDCLK

8

D+3.3V

6

GND

7

D+3.3V

5

CMD

4

GND

3

SDDAT3

2

GND

1

SDDAT2

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

29

H

14

BDRF(+)

15

BDRF(-)

16

GND

17

RF(+)

18

RF(-)

19

GND

20

+5V

21

A

22

B

23

C

24

D

25

VC-PD

26

E

27

F

28

G

13

GND

23

WP

22

CD

21

SDDAT1

20

GND

19

SDDAT0

18

GND

17

SDCLK

16

D+3.3V

14

GND

15

D+3.3V

13

CMD

12

GND

11

SDDAT3

10

GND

9

SDDAT2

23
22
21
20
19
18
17
16
15
14
13
12
11
10

9

8

GND

7

GND

6

GND

8
7
6

5

GND

4

GND

3

GND

5
4
3

2

GND

1

GND

2
1

CN1003

CN6001

23

P-ON+5V(2)

22

GND

21

GND

20

P-ON+1.2V

19

P-ON+1.2V

18

P-ON+1.2V

17

P-ON+1.2V

16

GND

15

GND

13

GND

14

GND

12

GND

11

P-ON+1.8V

10

P-ON+1.8V

9

P-ON+1.8V

8

GND

7

GND

6

P-ON+3.3V

5

P-ON+3.3V

4

P-ON+10.5V

3

P-ON+10.5V

2

P-ON+5V(1)

1

NU

23
22
21
20
19
18
17
16
15
14
13
12
11
10

9

8

7

6

5

4

3

2

1

CN1002

W007

W009

CN1001

1

AC120V

1

2

AC120V

2

INLET CBA

CN1004 CN2008

VIDEO CBAAUDIO CBA

FRONT A CBA

FRONT B

CBA

CN7101

CN4000

1

NU

2

GND

3

VIDEO

4

GND

5

VIDEO-Y(I/P)

6

GND

7

VIDEO-Pb/Cb

8

GND

9

VIDEO-Pr/Cr

11

SPDIF

10

GND

12

GND

13

SUB-RXD

14

SUB-TXD

15

SYS-RESET

16

RDY

17

CEC

1

2

3

4

5

6

7

8

9
10
11
12
13
14
15
16
17

CN7001

CN2007

CN3002

CN2002

CN2005 CN4001

19

AUDIO(L)-MUTE

20

AUDIO(R)-MUTE

21

GND

19
20
21

22

AUDIO(L)

23

GND

24

AUDIO(R)

22
23
24

25

AUDIO+5V

26

AUDIO+5V

25
26

14

EV+5V

14

1

F1

1

2

FL

2

3

FL-SDA

3

4

FL-SCL

4

5

FL-STB

5

6

FL-RESET

6

7

GND

7

8

GND

8

9

F2

9

10

GND

10

11

EV+3.3V

11

12

REMOTE

12

13

GND

13

15

KEY-2

15

16

KEY-1

16

17

NU

18

STANDBY/POWER-LED

17
18

CN3001CN3101

1

KEY-2

2

KEY-1

3

GND

123

CN4002

CN5501

1

REMOTE

1

2

EV+5V

2

3

NU

3

4

NU

4

5

NU

5

6

GND

6

REMOTE JACK CBA

14

MUTE2
14

5

EV+5V
5

6

REMOTE

6

7

GND
7

8

RDY
8

9

SYS-RESET
9

10

SUB-TXD
10

11

SUB-RXD
11

12

GND
12

13

NU
13

15

MUTE1
15

16

VIDEO+5V
16

17

CEC
17

14

SAFETY
14

1

EV+5V
1

2

P-ON+14.5V

2

3

NU
3

4

F1-IN
4

5

F2-IN
5

6

+FL
6

7

GND
7

8

GND
8

9

NU
9

10

PWSW1
10

11

PWSW2
11

12

FAN-CONT2(NU)
12

13

PWSW4
13

15

FAN-CONT1
15

16

FAN-LOCK
16

W006

AC CORD

AUDIO(L)

-OUT

AUDIO(R)

-OUT

VIDEO

-OUT

DIGITAL

AUDIO OUT

(COAXIAL)

VIDEO-Y

OUT

VIDEO

-Pb/Cb

OUT

VIDEO

-Pr/Cr

OUT

REMOTE

-IN

REMOTE

-OUT

DBP-1610

60

LEAD IDENTIFICATIONS

28

15

14

1

1234

48

17

32

33

16

1

64

49

123

54

1 4

8 5

1

2

4
3

1: Anode
2: Cathode
3: Emitter
4: Collector

C

BE

ECB

ECB

ECB

GDS

RA K

14

85

GDS

BCE

Note:

A: Anode
K: Cathode
E: Emitter
C: Collector
B: Base
R: Reference
G: Gate
D: Drain
S: Source

MM1757EHBE

2SA1980M Y
2SA1980MG-AT
2SC5343MG-AT
KRA104M-AT/P
KRC102M-AT/P
KRC103M-AT/P
KRC106M-AT/P
KTC3199-GR-AT/P
KTA1267(GR, Y)-AT/P
RN1203(TE4 F T)
RN1206
SRA2204M-AT
SRC1202M-AT
SRC1206M-AT
SRC1203MAT

PQ070XF01SZH
PQ070XFC1SZF

KTA1273-Y-AT/P

KTC2026-Y/P 2SK3563(Q)

2SK3563(Q M)

PST8430NR
S-80930CNMC-G80T2(G, J)

EL817(B, C)
LTV-817(B, C)-F
PS2561A-1(W)

BD9323EFJ-E2
FA5573N-D1-TE1

2SC3928A-T112-1Z
2SC5343SFG
2SC5343SG
KTC3875S-GR-RTK/P

NJM4580E-TE1

MN101C77A GC

2SA1015-(GR, Y)(TE2 F T)
2SA1981Y-AT
2SA950-Y(TE2 F T)
2SA966-Y(TE6 F M)
2SC1815-GR(TE2 F T)
2SC2120-Y(TE2 F T)
2SC5344 Y
KTA1271-Y-AT/P
KTC3203-Y-AT/P
STB1277LY-AT

KHB4D5N60F-U/PMC

STC403

61

DBP-1610

--MEMO--

62

DBP-1610

EXPLODED VIEW s

BD Main CBA &
BD Mechanism
Assembly

2L040

A4

A2

A22

A6

A6

A6

B4

W007

FM1001

A8

SD CBA

A1X

2L057

2L051

2L032

2L032

2L018

2L036

2L036

2L018

2L018

2L018

B2

2L054

2L028

1B1

2L056

2L034

B71

B70

B72

B73

W009

2L027

2L015

2L036

2L026

2L082

2L082

2L082

A3

W006

Front A CBA

Audio CBA

Remote Jack CBA

Video CBA

Inlet CBA

Power Supply CBA

Front B CBA

A21

2L072

2L081

2L081

2L081

2L083

2L081

2L079

2L089

2L073

2L070

2L070

B39

B77

B77

2L036

2L036

s

s

s

s

63

DBP-1610

--MEMO--

64

DBP-1610

PARTS LIST OF EXPLODED VIEW

s

s

sss

s

＊ Parts for which "nsp" is indicated on this table cannot be supplied.

＊

P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts

＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.

Ref. No. Part No. Part Name Remarks Q'ty New

9H2189002290D AV ASSEMBLY 1VSA22251 1 *

- VIDEO CBA -

- AUDIO CBA -

- FRONT A CBA -

- FRONT B CBA -

9H2189002300D POWER ASSEMBLY 1VSA22246 1 *

- POWER SUPPLY CBA -

- REMOTE JACK CBA -

-SD CBA -

-INLET CBA -

1B1 9H2309002280D BD MAIN CBA & BD MECHANISM ASSEMBLY N77D1BUN *

A1X 9H2402002230D FRONT ASSEMBLY E5KC1UD 1VM123602 1 *

A2 nsp CHASSIS E5KA0UD 1VM021192 1

A3 9H2403001970D TOP COVER E5KA0UD 1VM021193 1

A4 9H2406002240D REAR PANEL E5KC1UD 1VM227738 1 *

A6 9H2407001020S FOOT ASSEMBLY E5H50UD 1VM430199A 4

A8 9H2418001990D TRAY PANEL ASSEMBLY E5KA0UD 1VM227177 1

A21 nsp LABEL SERIAL NO. E57E0UD - 1

A22 nsp LICENSE LABEL E5KA0UD - 1

.

B2 nsp FRONT BRACKET(B2 DENON MOLD) E5KC1UD S/No.~04800 1VM330757 1

B2 nsp FRONT BRACKET(B2 DENON MOLD) E5KC1UD S/No.04801~ 1VM330757C 1

B4 nsp POWER HOLDER E5KA0UD 1VM122880 1

B39 nsp LEAD CLAMPER 100MM 1790356 3

B70 nsp HIMELON TAPE(5X40) E5KA0UD 1VM431686 1

B71 nsp HIMELON TAPE(5X25) E5KA0UD 1VM431688 1

B72 nsp AV PCB BRACKET E5KA0UD 1VM226905 1

B73 nsp LOADER BRACKET E5KA0UD 1VM122901 1

B77 nsp WASHER E5KB0UD S/No.~04800

B77

FM1001 9H2685001110S MOTOR DC FAN 2D65BL100190 MMEZR12XNR08 1

W006 9H2606002250S WIRE ASSEMBLY FFC 8/177/1.0 WX1E5KC1-002 1

W007 nsp WIRE ASSEMBLY VH 2/265/AWG20 WX1E5KA0-007 1

W009 nsp WIRE ASSEMBLY PH 16/290/AWG24 WX1E5KA0-009 1

SCREWS

2L015 nsp SCREW TAP TIGHT WASHER+ P-TIGHT GCJP3080 2

2L018 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 9

2L026 nsp SCREW S-TIGHT M3X6 E5E10UD 1VM429667 3

2L027 nsp SCREW S-TIGHT M3X6 E5E10UD 1VM429667 2

2L028 nsp SCREW S-TIGHT M3X10 E5610UD 0VM412936A 4

2L032 nsp SCREW S-TIGHT M3X6 E5E10UD 1VM429667 6

2L034 nsp SCREW S-TIGHT M3X6 E5E10UD 1VM429667 4

2L036 nsp SCREW S-TIGHT M3X6 BIND HEAD+ S/No.~04800 GBJS3060 7

2L036 nsp SCREW S-TIGHT M3X6 BIND HEAD+ S/No.04801~ GBJS3060 9

2L040 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 4

nsp WASHER E5KB0UD S/No.04801~

1VM432940

1VM432940

2

2

65

DBP-1610

Ref. No. Part No. Part Name Remarks Q'ty New

2L051 nsp SCREW TAP TIGHT WASHER+ P-TIGHT GCJP3080 2

2L054 nsp SCREW C-TIGHT M3X6 E5610UD 0VM412937A 6

2L056 nsp SCREW S-TIGHT M3X6 E5E10UD 1VM429667 4

2L057 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 1

2L070 nsp B-TIGHT SCREW M3X8 E5E00UD 1VM428563 8

2L072 nsp B-TIGHT SCREW M3X8 E5E00UD 1VM428563 1

2L073 nsp B-TIGHT SCREW M3X8 E5E00UD 1VM428563 2

2L079 nsp S-TIGHT SCREW M3X6 E5E00UD 1VM428564 1

2L081 nsp S-TIGHT SCREW M3X6 E5E00UD 1VM428564 5

2L082 nsp S-TIGHT SCREW M3X6 BIND HEAD+BLACK GBHS3060 9

2L083 nsp S-TIGHT SCREW M3X6 E5E00UD 1VM428564 1

2L089 nsp S-TIGHT SCREW M3X6 E5E00UD 1VM428564 2

66

DBP-1610

PACKING VIEW

A30

S3

S1

X19

S1

X10

X12

X38 X15 X14 X6

Lower SideUpper Side

X1

A20

S2

A30

67

DBP-1610

PARTS LIST OF PACKING & ACCESSORIES

＊ Parts for which "nsp" is indicated on this table cannot be supplied.

＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.

Ref. No. Part No. Part Name Remarks Q'ty New

A20 nsp BARCODE LABEL E5KC1UD

A30 nsp CONTROL LABEL E5KC1UD

S1 9H2533002010D SIDE PAD E5KA0UD

S2 9H2531002260D GIFT BOX CARTON E5KC1UD

S3 nsp SET BAG E7708UA

X1 9H2541002270D OWNERS MANUAL E5KC1UD

X6 nsp MANGANESE DRY BATTERY R6UWC/2STA

X6 nsp MANGANESE DRY BATTERY R6UWC/2SK

X6 nsp DRY BATTERY ES-GR6M-C

X10 nsp ACCESSORY BAG E5795ED

X12 nsp SERVICE CENTER SHEET E8700UD

X14 nsp AV CORD 1000/BLACK

X14 nsp AV CORD RCA(M*2)TO RCA(M*2)

z X15 00D9H26000887
z X15 nsp CORD W/O A GND WIRE UL/CSA(VW-1)/152/NO/
z X15 nsp CORD W/O A GND WIRE UL/CSA(VW-1)/152/NO/

X19 9H2307002060D REMOTE CONTROL UNIT NB420UD

X38 nsp WARRANTY SHEET E6E80UD

AC CORD WITH A GND WIRE UL/CSA/ 162/NO/BLACK

1VM123019

1VM330859

0DM400731D

1VMN27754

XB0M311MS003

XB0M311MS002

XB0M571GLP01

0VM416059

1VM425536F

WPZ0102TM018

WPZ0102LTE01

WAV0162LW001

WAV0152LTE01

WAV152ZHN001

NB420UD

1VM323952C

-

-

1

2

2

1*

1

1*

2

2

2

1

1

1

1

1

1

1

1

1

68

DBP-1610