Specifications and Main Features
- Device Designation: DAP-5500
- Input Sensitivity/Input impedance suited for:
- LINE-1-2: 1 V/10 kohm for SOURCE DIRECT ON mode.
- TAPE-1 2: 150 mV/10 kohm for SOURCE DIRECT OFF mode.
- LINE-3: 1 V/10 kohm (Balanced input - Direct input selected)
- 150 mV/10 kohm (Balanced input - Direct input not selected)
-Akceptowalne wtyki: Wtyki XL typu CANNON
- Terminals for Outputs:
- PRE-OUT-1: 1/10 ohm (Unbuffered type) / 15 V RMS
- PRE-OUT-2; Pazitive/Negative output: 2 V/600 ohm/30 V RMS
-Response on Frequency: 1 Hz to 300 kHz at 3 dB limit
-Distortion caused due to Harmonics: 0.002% (20 Hertz < f < 20k Hertz at 5 Volt output)
-Ratio inverse to Noise: 116 Decibels
- Terminals for DAC Outputs: Terminals for analogue output proceed from a converter
-535719ohms and 470ohm are the stated output impedances.
-Output Voltage stands at 2 V when the CD is at a maximum recording level of 10 Kohm Load.
-Digital Audio Interface, includes 75 Ohm Coaxial cable for input and optical input terminals-output systems
-Converter Strategy: 4DA push pull: super linear converter
Filters specifications: 4 times oversampling digital filter; 7 pole analog filter
-Digital responsive frequency bandwidth operates between 2 Hz to 20Khz at +0.2 dB
-Digital responsive section ratio converse to noise operates at 110Dbs
-Range-Dynamic: More than 97 Dbs
- Total Harmonic Distortion: Less than 0.002 percent (at 1 kHz)
- Channel Separation: More than 100 dB (for 1kHz signal)
- FSK Control of the Sampling Frequency: 32 kHz, 44,1 kHz, 48 kHz
- Power Supply Rating:
- 120 volts alternated current at 60 hertz and 25 watts (for USA & Canada)
- 220 volts at 50 hertz and 25 watts (for Europe)
- 240 volts at 50 hertz and 25 watts (for UK & Australia)
- 110/120/220/240 volts at 50/60 hertz 20 watts for Asia
- Size: 434 mm in W (17-3/32'') X 133 mm in H (5-15/64'') X 380 mm in D (14-61/64'')
- Weight: 13.7 kg, 30 lbs 3 oz
Frequently Asked Questions
- What types of inputs does DAP-5500 accept?
DAP-5500 accepts multiple input types, including conventional RCA jacks, balanced inputs using XL type CANNON connectors and digital coaxial, optical and S/PDIF.
- What is the output voltage for the DAP-5500?
The output rating of the DAP-5500 is 2 V (at a load of 10 kohm)
- What is the frequency response range of the DAP-5500?
Frequency response is flat in DAP - 5500, which from 1Hz to 300 kHz.
- What is the signal to noise ratio S/N ratio of DAP-5500.
The S/N ratio of DAP 5500 is typical and measured at 116 dB.
- What are the power specifications of the DAP-5500?
The power specifications are different depending on the geographic location:
- 25 Watt and 120 Volt with a frequency of 60 Hertz intended for use in the USA and Canada.
- 25 Watt and 220 Volt with a frequency of 50 Hertz intended for use in Europe.
- 25 Watt and 240 Volt with a frequency of 50 Hertz intended for use in the UK and Australia.
- 20 Watt and 220 – 120 Volt with a frequency of 50 – 60 Hertz intended for use in Asia.
User Manual
Loading...