Specifications and Main Features
- Model: DAP-2500 Digital Audio Preamplifier
- Equalizer Amplifier:
- Determined Sensitivity / Impedance:
- PHONO MC: 0.2 mV/100 ohms
- PHONO MM: 2.5 mV/47 kohms
- Input Level, Maximum:
- PHONO MC: 13 mV/1 kHz
- PHONO MM: 160 mV/1 kHz
- Output Maximum / Rated Output: 10 V/150 mV
- Harmonic Distortion Total: Less than 0.001% (1 kHz, rated output)
- Deviation RIAA:
- PHONO MC: 20 Hz~100 kHz +0.3 dB
- PHONO MM: 20Hz-20kHz +0.2 dB
- Ratio Signal noise:
- PHONO MC:79 dB (0.5 mV input A-weighted)
- PHONO MM: 96 dB (5 mV input)
- Gain:
- PHONO MC: 57.5 dB/1 kHz
- PHONO MM: 35.6 dB/1 kHz
- On a subsonic filter for Phono: 16 Hz, 12dB/oct.
- Digital Section:
- Format: Interface audio digital with 16 bits linear
- Frequencies: 32kHz, 44.1kHz and 48kHz
- Terminals Inputs:
- Optical: DIGITAL-1: 1 line
- Coaxial: DIGITAL-2, 3: 0.5 Vp-p/75 ohm
- Dat Terminals: Dat digital in 0.5 Vp-p/75 ohm
- Dat digital out: 0.5 Vp-p/75 ohm
- D/A Conversion System: 4DA push-pull - Super Linear Converter
- Total Harmonic Distortion: 0.0025%, 1kHz and 0dB
- Frequency-response: 2Hz-20KHz, + 0.3dB
- Signal to Noise Ratio: 108dB(Aweighted)
- Dynamic Range: 97dB
- High Level Amplifier:
- Terminals Inputs: CD, TUNER, AUX-1 , AUX-2
- Terminal Tape Input/Output: TAPE-1, TAPE-2
- Input Sensitivity / O./ Impedance: SOURCE DIRECT ON 1V/10kohm
- Rated Output / Impedance:
- PRE OUT-1: 1V/10 ohms
- PRE OUT-2 (Balanced-Out): 2V/600 ohms
- Total Harmonic Distortion: 0.002%(20 Hz~20 KHz 1 V output)
- Signal to Noise Ratio: 105 dB (Aweighted)
- Frequency Response: 1 Hz-300 kHz +0.2 dB -3 dB
- General:
- Supply: AC120V=60Hz (U.S.A and Canada) AC110/120/220/240 50/60Hz(multiple)
- Consumption: 28W
- Dimensions: 434(W) x 136(H) x 386(D) mm
- Weight: 8.5kg
- Remote Control:
- Remote Control Unit RC-109 (40 key system)
- Power Supply 3 V DC two size RO3 (AAA) dry cell batteries
- Dimensions Measures 60 (w) x 180 (h) x 17.5 (d) mm
- Weight110 g (including battery)
Frequently Asked Questions
- Q: What is the input sensitivity of the PHONO MM?
- A: Input sensitivity of PHONO MM is 2.5 mV/47 kohms.
- Q: What is the maximum output level of the device?
- A: Maximum output level reaches up to 10 V/150 mV.
- Q: Does the DAP-2500 have any digital input options?
- A: Yes, there are options for connecting the device with optical and coaxial digital inputs.
- Q: What is the total harmonic distortion in the rated output conditions.
- A: It should be noted that this level of distortion is well below 0.001% considering 1 kHz frequency.
- Q: What method can I use to adjust the volume of the device?
- A: The volume can be adjusted with the help of the volume knob mounted on the device or using the remote control unit.
- Q: How do I eliminate interference with my tuner or television?
- A: Try to place the DAP-2500 furthest from the tuner or television and also try to separate the connecting cables from the antenna wires.
User Manual
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
Page 43
Page 44
Page 45
Page 46
Page 47
Page 48
Loading...