Denon AVR-888 User Manual
AV SURROUND RECEIVER
AVR-888
Owner’s Manual
Manuel de l’Utilisateur
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FIGURE A
EXAMPL E OF ANTENN A GROUNDING
AS PER NATIONAL
ELECTR ICAL CODE
"/5&//"
-&"%*/
8*3&
(306/%
$-".1
&-&$53* $
4&37*$&
&26*1.& /5
"/5&//"
%*4$)"3 (&6/*5
/&$4&$5 *0/
(306/%* /($0/%6$ 5034
/&$4&$5 *0/
(306/%$- ".14
108&34&3 7*$&(306 /%*/(
&-&$530 %&4:45&.
/&$"35 1"35)
/&$/"5*0 /"-&-&$5 3*$"-$0% &
ENGLISH FRANCAIS
SAFETY PRECAUTIONS
n
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
I
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions – The safety and operating instructions should be
retained for future reference.
3. Heed Warnings – All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should be followed.
5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the
product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. A product and cart combination should be moved
with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
11. Power Sources – This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other
sources, refer to the operating instructions.
12. Grounding or Polarization – This product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13. Power-Cord Protection – Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
15. Outdoor Antenna Grounding – If an outside antenna or cable system is
connected to the product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode. See
Figure A.
16. Lightning – For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into this product
through openings as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
20. Servicing – Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
21. Damage Requiring Service – Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance – this
indicates a need for service.
22. Replacement Parts – When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer
or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
FCC INFORMATION (For US customers)
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
n
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Unplug the power cord when not using the
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
ENGLISHFRANCAIS
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
II
ENGLISH
Contents
Getting Started
Accessories ······················································································2
Cautions on Handling ····································································· 3
Cautions on Installation ·································································3
About the Remote Control Unit ····················································3
Inserting the Batteries ····································································3
Operating Range of the Remote Control Unit ································ 3
Part Names and Functions ·····························································4
Front Panel ····················································································· 4
Display ···························································································4
Rear Panel ······················································································5
Remote Control Unit ······································································ 6
Connections
Preparations ····················································································7
Cables Used for Connections ························································7
Video Conversion Function ····························································· 8
On-Screen Display for Component Video Outputs and
HDMI Output ·················································································8
Speaker Connections ·····································································9
Speaker Installation ········································································9
Speaker Connections ······························································· 9, 10
Connecting Equipment with HDMI connectors ························· 11
Connecting the Monitor ······························································· 12
Connecting the Playback Components ······································12
DVD Player ··················································································· 12
Record Player ···············································································13
CD Player ·····················································································13
iPod® ···························································································· 14
TV/CABLE Tuner ··········································································· 14
Connecting the Recording Components ···································· 15
Digital Video Recorder ·································································· 15
Video Cassette Recorder ····························································· 15
CD Recorder / MD Recorder / Tape Deck ····································· 16
Connections to Other Devices ····················································· 16
Video Camera / Game Console ···················································· 16
Component with Multi-channel Output connectors ····················· 17
XM connector ··············································································17
Antenna terminals ·······································································18
Multi-zone ····················································································19
Connecting the Power Cord·························································19
Once Connections are Completed ··············································19
Menu Operations
Operations ····················································································· 20
Example of Display of Default Values ········································· 20
Examples of On-screen Display and Front Display ····················21
Menu Map ·····················································································22
Auto Setup
Preparations ··················································································23
Auto Setup ····················································································24
a Start Menu ·············································································· 24
Error Messages ·······································································25
s
Option ····················································································· 25
d
Parameter Check ·····································································25
Manual Setup
Speaker Setup···············································································26
a Speaker Configuration ·····························································26
s Subwoofer Setup ···································································· 26
d Distance ············································································ 26, 27
f Channel Level··········································································27
g Crossover Frequency ······························································ 27
HDMI Setup ···················································································27
a HDMI Audio Setup ··································································27
s HDMI Video Setup ·································································· 28
Audio Setup ··················································································28
a EXT. IN Subwoofer Level ························································· 28
s 2ch Direct/Stereo ······························································ 28, 29
d Dolby Digital Setup ·································································29
f Auto Surround Mode ······························································29
g Manual EQ ··············································································29
Zone2 Setup ··················································································30
a Lch Level ·················································································30
s Rch Level ················································································30
d Volume Limit ···········································································30
f Power On Level ······································································· 30
g Mute Level ··············································································30
Option Setup ················································································· 30
a Amp Assign ·············································································30
s Volume Control ·······································································31
d Source Delete ·········································································31
f On-Screen Display ··································································31
g Quick Select Name ·································································32
h Remote ID Setup ····································································32
j Display ····················································································32
k Setup Lock ·············································································· 32
Input Setup
Settings Related to Playing Input Sources ·································33
Auto Preset ·················································································· 33
Preset Skip ···················································································33
Preset Name ················································································ 33
Input Mode ··················································································34
Rename ························································································ 34
Assign ····················································································34, 35
iPod ······························································································ 35
Other ······················································································35, 36
Antenna Aiming ···········································································36
Surround Modes
Standard Playback ········································································ 36
Surround Playback of 2-channel Sources ·····································36
Playing Multi-channel Sources (Dolby Digital, DTS, etc.) ·············36
DSP Simulation Playback·····························································37
Stereo Playback ············································································37
Direct Playback ·············································································37
Playback in the PURE DIRECT Mode ··········································· 37
Parameter
a Surround Parameter ····························································38, 39
s Tone Control ·············································································· 40
d Room EQ ··················································································· 40
f RESTORER ················································································ 40
g Night Mode ···············································································41
h Audio Delay ···············································································41
Information
Status ····························································································41
a Main Zone ··············································································· 41
s ZONE2 ····················································································41
Audio Input Signal ········································································ 41
HDMI Information ·········································································42
a HDMI Signal Information ························································42
s HDMI Monitor Information ·····················································42
Auto Surround Mode ····································································42
Quick Select ··················································································42
Preset Station ···············································································42
r y
u
i
Playback
Preparations ··················································································43
Turning the Power On ··································································43
Selecting the input source ···························································43
Operations During Playback ·························································43
Playing Video and Audio Equipment ···········································44
Basic Operation ············································································ 44
Listening to FM/AM Broadcasts ·················································44
Basic Operation ············································································ 44
Presetting Radio Stations (Preset Memory) ································· 44
Listening to Preset Stations ·························································44
Listening to XM Satellite Radio Programs ·································45
Basic Operation ············································································ 45
Checking the XM Signal Strength and Radio ID ··························· 46
Searching Categories ··································································· 46
iPod® Playback ············································································· 46
Basic Operation ············································································ 46
Listening to Music ·······································································47
Viewing Still Pictures or Videos on the iPod ·································47
Other Operations and Functions
Other Operations ··········································································48
Recording on an External Device (REC OUT mode) ·····················48
Convenient Functions ··································································48
Channel Level ···············································································48
Fader Function ·············································································48
Quick Select Function ··································································49
Personal Memory Plus Function ·················································· 49
Last Function Memory ·································································49
Backup Memory ··········································································· 49
Resetting the Microprocessor ······················································49
Amp Assign / Multi-zone Connections and Operations
Multi-zone Settings with the Amp Assign Function ·········54 ~ 56
Multi-zone Settings and Operations with Zone Output·················56
Multi-zone Operations ·································································57
Turning the Power On and Off······················································57
Selecting the Input Source ··························································· 57
Adjusting the Volume ···································································57
Turning off the Sound Temporarily ················································57
Other Information ································································ 58 ~ 66
Troubleshooting ···································································67 ~ 69
Specifications ··············································································· 70
List of preset codes ··········································· End of this manual
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Getting Started
Thank you for purchasing this DENON product. To ensure proper
operation, please read this owner’s manual carefully before using the
product.
After reading them, be sure to keep them for future reference.
Accessories
Check that the following parts are supplied with the product.
q Owner’s manual ...................................................................... 1
w Warranty (for North America model only) ................................1
e Service station list ...................................................................1
r Remote control (RC-1080) ....................................................... 1
t R6P/AA batteries ..................................................................... 2
y FM indoor antenna ..................................................................1
u AM loop antenna ..................................................................... 1
i Setup microphone (Cord length: Approx. 25 ft / 7.6 m) ............ 1
Remote Control Unit Operations
Operating DENON Audio Components·······································50
Presetting ······················································································50
Operating Preset Component ··············································50 ~ 52
Punch Through Function ······························································ 53
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Cautions on Handling
• Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
•
Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
• About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
• Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
•
Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
Cautions on Installation
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
b Note
b
b
b
About the Remote Control Unit
In addition to the AVR-888, the included remote control unit (RC-1080)
can also be used to operate the equipment listed below.
q DENON system components
w Non-DENON system components
• By setting the preset memory (vpage 50 ~ 52)
Inserting the Batteries
q Lift the clasp and remove the
rear lid.
e Put the rear cover back on.
NOTE
• Replace the batteries with new ones if the set does not operate even
when the remote control unit is operated close to the unit.
• The supplied batteries are only for verifying operation.
• When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
• If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
• Remove the batteries from the remote control unit if it will not be in
use for long periods.
• When replacing the batteries, have the new batteries ready and
insert them as quickly as possible.
w Load the two batteries properly
as indicated by the marks in the
battery compartment.
R6P/AA
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating it.
30°
30°
Approx. 23 feet / 7 m
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Wall
q w e r
W1 W2 W3 W4 W5 W6 W7 W8 W9 E0
y u i o Q0 Q1 Q2 Q3t
Q4Q5Q6Q7Q8Q9W0
u yiQ4Q5 oQ0Q1Q2Q3
wq e r t
Part Names and Functions
For buttons not explained here, see the page indicated in parentheses ( ).
Front Panel
Q9 SOURCE SELECT knob······························· (43)
W0 SOURCE button ·········································· (43)
W1 INPUT MODE button ·································· (34)
W2 ANALOG button ·········································· (34)
W3 EXT. IN button ············································· (34)
W4 BAND button ··············································· (44)
Display
ENGLISH
W5 SHIFT button ···············································(44)
W6 PRESET buttons ·········································· (44)
W7 TUNING buttons ·········································(44)
W8 VIDEO SELECT button ·······························(35)
W9 DIMMER button ·········································· (32)
E0 STATUS button ···········································(45)
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
q Power operation button
(ON/STANDBY) ···········································(43)
w Power indicator ··········································· (43)
e Power switch (hON jOFF) ····················(43)
r Headphones jack (PHONES) ······················ (43)
t SPEAKER buttons ·······································(43)
y ZONE2 ON/OFF button ······························ (57)
u QUICK SELECT buttons ·····························(49)
i V. AUX INPUT connectors
Remove the cap covering the terminals when
you want to use them.
o SETUP MIC jack ·········································· (23)
Q0 MENU button ··············································(20)
Q1 RETURN button ·········································· (20)
Q2 SELECT/ENTER knob ································· (20)
• The SELECT/ENTER knob on the main unit operates
in the same way as the CURSOR o and p buttons
on the remote control unit.
• The control functions in the same way as the
CURSOR o button when turned counterclockwise,
as the CURSOR p button when turned clockwise.
• The control functions in the same way as the
ENTER button when pressed the knob.
Q3 Cursor buttons (ui) ·································(20)
Q4 MASTER VOLUME control knob ················ (43)
Q5 Master volume indicator
Q6 Display
Q7 Remote control sensor ································· (3)
Q8 ZONE2/REC SELECT button ······················ (48)
q Input signal indicators
w Input signal channel indicators
These light when digital signals are input.
e Information display
The input source name, surround mode, setting
values and other information are displayed here.
r Output signal channel indicators
t Front speaker indicator
These light according to the settings of the front
A and B speakers.
y ZONE2 output indicator
This lights when the power for the ZONE2 is
turned on.
u Master volume indicator
i AUDYSSEY MULTEQ indicator
This lights when the room equalizer is selected.
o Input mode indicators
Q0 Recording output source indicator
This lights when the REC OUT mode is
selected.
Q1 NIGHT indicator
This lights when the night mode is selected.
Q2 RESTORER indicator
This lights when the RESTORER mode is
selected.
Q3 HDMI indicator
This lights when playing using HDMI
connections.
Q4 Decoder indicators
These light when the respective decoders are
operating.
Q5 Tuner reception mode indicators
These light according to the reception conditions
when the input source is set to “TUNER”.
• AUTO
This lights when in the auto tuning mode.
• STEREO
In the FM mode, this lights when receiving
analog stereo broadcasts.
• TUNED
This lights when the broadcast is properly tuned
in.
ENGLISH
q
Q2 Q3 Q4
Q5 Q6 Q2
w e r
u yioQ0Q1
t
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Rear Panel
q REMOTE CONTROL jack ···························· (19)
w DOCK CONTROL jack ································· (14)
e Speaker terminals (SPEAKERS) ··················(9)
r SIGNAL GND terminal ······························· (13)
t AC OUTLETS ··············································· (20)
y AC inlet (AC IN) ···········································(20)
u Digital audio connectors
(OPTICAL / COAXIAL) ·························· (12, 15)
i COMPONENT VIDEO connectors ·············· (12)
o XM connector (SAT TU) ······························ (17)
Q0 HDMI connectors ·········································(11)
Q1 VIDEO / S-VIDEO connectors ···················· (12)
Q2 Analog audio connectors (AUDIO) ············ (12)
Q3 FM/AM antenna terminals
(TUNER ANTENNA) ···································· (18)
Q4 ZONE2 connectors······································ (19)
Q5 EXT. IN connectors ····································· (17)
Q6 PRE OUT connector ······································(9)
q
y
u
i
o
w
e
r
t
Q0
Q2
Q3
Q4
Q5
Q6
Q1
q
e
w
r
t
y
i
Q1
Q0
u
o
Remote Control Unit
[ Front ] [ Rear ]
q Indicator ······················································(50)
w Power buttons·············································(43)
e Tuner system buttons ································(44)
r Source select buttons ································ (43)
t System buttons ·········································· (47)
y Video select button (V. SELECT) ···············(35)
u Cursor buttons (uio p) ·························(20)
i DISPLAY button ··········································(41)
o DIMMER button ·········································· (32)
Q0 Mode selector switches ······················· (44, 46)
Q1 Remote control signal transmitter ·············· (3)
Q2 Master volume control buttons ················(43)
Q3 MUTING button ·········································· (43)
Q4 NIGHT button ·············································· (41)
Q5 STATUS button ···········································(45)
Q6 Channel select (CH SEL) /
ENTER button ······································· (20, 48)
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
q ZONE2 power buttons ······························· (57)
w Source select buttons ································ (43)
e Tuner system buttons ································(44)
r Test tone button (TEST) ····························· (27)
t Main zone power buttons (MAIN) ············(57)
y Surround mode buttons ······················(36, 37)
u Amp menu button (A. MENU) ···················(20)
i Input mode button (INPUT) ·······················(34)
o Enter button (ENT) ····································· (20)
Q0 RETURN button ·········································· (20)
Q1 Cursor buttons (uio p) ·························(20)
NOTE
If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated too.
ENGLISH
R
L
R
L
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Preparations
Connections
Connections for all compatible audio and video signal formats are
described in these operating instructions. Please select the types
of connections suited for the equipment you are connecting.
With some types of connections, certain settings must be made
on the AVR-888. For details, refer to the instructions for the
respective connection items below.
NOTE
• Do not plug in the power cord until all connections have been
completed.
• When making connections, also refer to the operating instructions of
the other components.
• Be sure to connect the left and right channels properly (left with left,
right with right).
• Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
Cables Used for Connections
Select the cables according to the equipment being connected.
Audio cables Video cables
Coaxial digital connections
(Orange)
Coaxial digital (75 Ω/ohms pin-plug) cable
Optical digital connections
Optical cable
Analog connections (stereo)
(White)
(Red)
Stereo pin-plug cable
Analog connections (monaural, for subwoofer)
(Black)
Pin-plug cable
Speaker connections
Component video connections
(Green)
(Blue)
(Red)
S-Video connections
Video connections
(Yellow)
Component video cable
S-Video cable
75 Ω/ohms pin-plug video cable
Audio and video cables
HDMI connections
19-pin HDMI cable
(Y)
(PB/CB)
(PR/CR)
Speaker cables
Audio signal: Video signal:
Output
Input
Signal direction
Input
Output
Output
Input
Input
Output
Video Conversion Function
• This function automatically converts various formats of video signals input to the AVR-888 into the format
used to output the video signals from the AVR-888 to a monitor.
• The AVR-888’s video input/output circuitry is compatible with the following four types of video signals:
Digital video signals: HDMI
Analog video signals: Component video, S-Video and Video
GFlow of video signals inside the AVR-888H
Main zone
High picture
quality playback
HDMI connector
HDMI connector
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
• When not using this function, connect a monitor output with the same type of connector as the video
input connector.
• The resolution of the HDMI input-compatible monitor connected to the AVR-888 can be checked at menu
“Information” – “HDMI Information” (vpage 42).
NOTE
• HDMI signals cannot be converted into analog signals.
• 1080p component input video signals cannot be output to anything other than component video
connectors.
• 480p/576p, 1080i and 720p component video input signals cannot be converted into S-Video or Video
format.
• When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
Component video
connectors
S-Video connector
Video connector
Video inputs Video outputs
: When 480i/576i signals are input in the main zone
Component video
connectors
S-Video connector
Video connector
Monitor
On-Screen Display for Component Video Outputs and HDMI
Output
• When viewing HDMI or component video signals via the AVR-888, the on-screen display appears when
the MENU button or the remote control unit’s DISPLAY button is operated.
• When only HDMI or component video signals are input to the AVR-888, the characters of the on-screen
display are not displayed over the picture.
ENGLISH
(R) (L)
(R) (L)
(L) (R)
*/
(L) (R)
w q w q
w q w q
w qw q
w qw q
w q
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Speaker Connections
Speaker Installation
The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and
a monitor.
Subwoofer Center speaker
Surround back speakers
Front speakers
Place the front speakers to the
sides of the monitor or screen and
as flush with the screen surface as
possible.
The table below shows a typical speaker configuration for the AVR-888.
Surround speakers
Speaker Connections
Example: 5.1-channels (FRONT A+B) and ZONE2 use
Front speakers
A
Front speakers
B
Center speakerSubwoofer
Subwoofer
with built-in
amplifier
7.1-channels
(FRONT A+B)
7.1-channels
6.1-channels
5.1-channels
3.1-channels
2.1-channels
2-channels
FRONT
L R L R L R 1 only
S S S S S S S
S S S S S S S
S S S S S
S S S S S
S S S
S S
S S
CENTER
SURROUND SURROUND BACK
–
–
– –
– – –
– – – – –
– – – – – –
– – – – – – –
S S
SUBWOOFER
S
S
S
S
S
b L : Left
R : Right
Surround speakers ZONE2 speakers
ZONE2
When using just one surround back speaker, connect it to the left channel (SBL).
NOTE
By default, the AVR-888’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for
the main zone, change the “Amp Assign” setting (vpage 30).
Connecting the Speaker Cables
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the AVR-888, and
be sure to interconnect the channels and polarities correctly.
Peel off about 0.03 ft/10 mm of sheathing
1
from the tip of the speaker cable, then
either twist the core wire tightly or
terminate it.
Turn the speaker terminal
2
counterclockwise to loosen it.
Insert the speaker cable’s core wire to
3
the hilt into the speaker terminal.
Turn the speaker terminal clockwise to
4
tighten it.
When using a banana plug
Tighten the speaker terminal firmly before
inserting the banana plug.
Protection circuit
If speakers with an impedance lower than specified (for example
4 Ω/ohms speakers) are used for an extended period of time with
the volume turned up high, the temperature may rise, activating the
protection circuit.
When the protection circuit is activated, the speaker output is shut
off and the power indicator flashes red. If this happens, unplug
the power cord, then check the speaker cable and input cable
connections. If the set is extremely hot, wait for it to cool off and
improve ventilation around it. Once this is done, plug the power cord
back in and turn the set’s power back on.
If the protection circuit is activated again even though there are no
problems in the ventilation around the set nor in the connections,
the set may be damaged. Turn the power off, then contact a DENON
service center.
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
NOTE
• Use speakers with an impedance of 6 to 16 Ω/ohms. When using
front A and B speakers simultaneously, use speakers with an
impedance of 8 to 16 Ω/ohms.
• Connect the speaker cables in such a way that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the + and – sides touch each
other (v “Protection circuit”).
• Never touch the speaker terminals while the power supply is
connected. Doing so could result in electric shock.
0
ENGLISH
065
)%.*
*/
)%.*
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Connecting Equipment with HDMI connectors
With HDMI connections, the video and audio signals can be transferred with a single cable.
MonitorDVD player
b The AVR-888 is equipped for HDMI version 1.3a. This version
is compatible with other versions, allowing connection to
all components equipped with an HDMI connector.
b The AVR-888 is compatible with 30- and 36-bit Deep
Color.
Compatible
audio format
2-channel linear
PCM
Multi-channel
linear PCM
Dolby Digital, DTS Bitstream DVD-Video
Details
2ch 32-192 kHz
16/20/24 bits
8ch 32-192 kHz
16/20/24 bits
Copyright protection system (HDCP)
In order to play the digital video and audio signals of a DVDVideo or DVD-Audio disc using HDMI/DVI connections, both
the connected DVD player and monitor must be equipped
for a copyright protection system called “HDCP” (Highbandwidth Digital Content Protection).
HDCP is a copy protection technology consisting of data
encoding and mutual identification of the devices.
The AVR-888 is HDCP-compatible. For details on the DVD
player or monitor you are using, refer to its operating
instructions.
Discs
(examples)
CD, DVD-Video,
DVD-Audio
DVD-Audio
NOTE
• Use a CPPM-compatible DVD player to play DVD-Audio discs that are copyright-protected by CPPM.
• The AVR-888 cannot be controlled from another device via the HDMI cable.
• The audio signals output from the HDMI connector (sampling frequency, bit rate, etc.) may be restricted
by the connected device.
• Video signals are not output properly when using devices that are not HDCP-compatible.
• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,
switch the DVD player’s resolution to a resolution with which the monitor is compatible.
• If the menu “Manual Setup” – “HDMI Setup” – “HDMI Audio Setup” setting (vpage 27) is set to
“AMP”, the sound may be interrupted when the monitor’s power is turned off.
• Use a cable on which the HDMI logo is indicated (a certified HDMI product) for connection to the HDMI
connector. Normal playback may not be possible when using a cable other than one on which the HDMI
logo is indicated (a non-HDMI-certified product).
• If the monitor or DVD player does not support deep color, deep color signal transfer is not possible.
• If the monitor or DVD player does not support xvYCC, xvYCC signal transfer is not possible.
• When the AVR-888 and DVD player are connected using an HDMI cable, also connect the AVR-888 and
monitor using an HDMI cable.
• If the connected monitor or DVD player only has a DVI-D connector, use an HDMI/DVI converter cable.
When using a DVI cable, no audio signals are transmitted.
• Use a Deep Color compatible cable for connection to Deep Color compatible devices.
When connecting with an HDMI/DVI converter cable (adapter)
• HDMI video signals are theoretically compatible with the DVI format.
When connecting to a monitor, etc., equipped with a DVI-D connector, connection is possible using an
HDMI/DVI converter cable, but depending on the combination of components in some cases the video
signals will not be output.
• When connecting using an HDMI/DVI converter adapter, the video signals may not be output properly
due to poor connections with the connected cable, etc.
• By default, the HDMI audio signals are output from the speakers connected to the AVR-888.
• To output the sound from the TV, make the settings at menu “Manual Setup” – “HDMI Setup” – “HDMI
Audio Setup” – “TV” (vpage 27).
Connecting the Monitor
47*%&0
*/
7*%&0
$0.10/&/57*%&0
: 1# 13
7*%&0
*/
)%.*
*/ */
R
L
R
L
47*%&0
065
"6%*07*%&0
$0.10/&/57*%&0
: 1# 13
7*%&0
065 065
"6%*0
$0"9*"-
065
3-
065065
)%.*
• Connect the cables to be used (vpage 8 “Video Conversion Function”).
• With HDMI connections, the video and audio signals can be transferred with a single cable.
• To output the audio signals to the monitor with HDMI connections, set menu “Manual Setup” – “HDMI
Setup” – “HDMI Audio Setup” to “TV” (vpage 27).
Monitor
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Connecting the Playback Components
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
DVD Player
• Connect the cables to be used.
• With HDMI connections, the video and audio signals can be transferred with a single cable.
DVD player
NOTE
• The component video connectors may be indicated differently on your monitor. For details, see the
monitor’s operating instructions.
• No audio signals are output from the HDMI monitor output connector. To play the sound by monitor, make
analog or digital audio output connections to monitor’s audio input connectors.
• The audio signals output from the HDMI connectors are only the HDMI input signals.
Video-converted HDMI signals are not included in the audio signals.
• Connect an HDP (High-Definition Player) in the same way.
• When using an optical cable for the digital audio connection, make the settings at menu “Input Setup”
– “Assign” – “Digital In” (vpage 35).
ENGLISH
(/%
"6%*0
065
R
L
R
L
R
L
"6%*0
"6%*0
$0"9*"-
065
3-
065
Getting Started Connections Setup Playback Remote Control Multi-Zone Information TroubleshootingGetting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Record Player
CD Player
ConnectionsGetting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Turntable (MM cartridge)
Connect the cables to be used.
CD player
• When connecting a record player with an MC cartridge, use a commercially available MC head amplifier
or a step-up transformer.
• Induction humming (a booming sound) may be produced from the speakers if the volume is raised with
no record player connected.
• With some record players, noise may be generated when the ground wire is connected. If so, disconnect
the ground wire.
NOTE
The AVR-888’s SIGNAL GND terminal is meant to reduce noise when a record player is connected. This is
not a safety ground terminal.
When using an optical cable for the digital audio connection, make the settings at menu “Input Setup”
– “Assign” – “Digital In” (vpage 35).
47*%&0
065
"6%*07*%&0
$0.10/&/57*%&0
: 1# 13
7*%&0
065 065
"6%*0
3-
065
$0"9*"-
065
R
L
R
L
065
)%.*
iPod
R
L
R
L
"4%3
R
L
R
L
"4%/8
ENGLISH
®
TV/CABLE Tuner
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Use a DENON Control Dock for iPod (ASD-1R, ASD-3N or ASD-3W, sold separately) to connect the iPod
to the AVR-888. For instructions on the Control Dock for iPod settings, refer to the Control Dock for iPod’s
operating instructions.
Example 1:
iPod
Example 2:
iPod
Connect the cables to be used.
TV tuner
• With the default settings, the iPod can be used connected to the VCR (iPod) connector.
• To assign the iPod to a connector other than VCR (iPod), make the settings at menu “Input Setup” –
“(input source to which iPod dock assigned)” – “Assign” – “iPod dock” (vpage 35).
When using an optical cable for the digital audio connection, make the settings at menu “Input Setup”
– “Assign” – “Digital In” (vpage 35).
ENGLISH
R
L
R
L
R
L
R
L
47*%&0
*/
3- 3-
*/*/065
"6%*07*%&0
*/065
015*$"-
065
"6%*07*%&0
065
R
L
R
L
R
L
R
L
47*%&0
*/
3- 3-
*/*/065
"6%*07*%&0
065
"6%*07*%&0
065
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Connecting the Recording Components
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
Digital Video Recorder
Connect the cables to be used.
Digital video recorder
or or
Video Cassette Recorder
Connect the cables to be used.
Video cassette recorder
or
• Make analog connections if you wish to record analog audio signals.
• When recording via the AVR-888, the playback device’s cable must be of the same type as the cable used
to connect the AVR-888’s DVR OUT connector.
Example: TV IN → S-Video cable : DVR OUT → S-Video cable
TV IN → Video cable : DVR OUT → Video cable
• When using a component video cable for the video connection, make the settings at menu “Input Setup”
– “Assign” – “Component In” (vpage 35).
NOTE
Do not connect the output of the component connected to the AVR-888’s OPTICAL2 output connector to
any input connector other than OPTICAL2.
• When recording via the AVR-888, the playback device’s cable must be of the same type as the cable used
to connect the AVR-888’s VCR OUT connector.
Example: TV IN → S-Video cable : VCR OUT → S-Video cable
TV IN → Video cable : VCR OUT → Video cable
• When using a component video cable for the video connection, make the settings at menu “Input Setup”
– “Assign” – “Component In” (vpage 35).
R
L
R
L
R
L
R
L
3- 3-
065 */
"6%*0
"6%*0
CD Recorder / MD Recorder / Tape Deck
R
L
R
L
47*%&0
065
"6%*07*%&0
7*%&0
065 065
015*$"-"6%*0
3-
065
Make analog connections if you wish to record analog audio signals, or digital connections if you wish to
record digital audio signals, depending on the types of connectors on the components being used.
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Connections to Other Devices
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
CD recorder /
MD recorder /
Tape deck
Video Camera / Game Console
Video camera / Game console
ENGLISH
R
L
R
L
R
L
R
L
R
L
R
L
46#
800'&3
$&/5&3 463306/%
#"$,
3-
463306/%
3-
'30/5
3-
"6%*0
XM
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Component with Multi-channel Output connectors
DVD player /
Super Audio CD player / External decoder
XM connector
• The AVR-888 is an XM Ready® receiver. You can receive XM® Satellite Radio by connecting to the
XM Mini-Tuner and Home Dock (includes home antenna, sold separately) and subscribing to the XM
service.
• Plug the XM Mini-Tuner and Home Dock into the XM connector on the rear panel.
• Position the Home Dock antenna near a south-facing window to receive the best signal.
For details, see “Listening to XM Satellite Radio Programs” (vpage 45, 46).
When making connections, also refer to the operating instructions of the XM Mini-Tuner and Home
Dock.
XM Mini-Tuner and Home Dock
• To play the analog input signals input to the EXT. IN connectors, press the EXT. IN button on the main unit
or INPUT button on the remote control unit and select “EXT. IN” or make the settings at menu “Input
Setup” – “Input Mode” – “Input Mode” – “EXT. IN” (vpage 34).
• The video signal can be connected in the same way as a DVD player (vpage 12).
• To play copyright-protected discs, connect the AVR-888’s EXT. IN connector with the DVD player’s analog
multi-channel output connector.
NOTE
Keep the power cord unplugged until the XM Mini-Tuner and Home Dock connection have been
completed.
• The XM name and related logo are registered trademarks of XM Satellite Radio Inc. All rights
reserved.
• XM Ready is a registered trademark of XM Satellite Radio Inc. All rights reserved.
Antenna terminals
An F-type FM antenna cable plug can be connected directly.
Direction of broadcasting station
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
FM antenna
75 Ω/ohms
Coaxial cable
FM indoor antenna
(supplied)
AM loop antenna assembly
Remove the vinyl tie and take
out the connection line.
a. With the antenna on top of
any stable surface.
Mount
AM loop antenna
(supplied)
Ground
Connect to the AM
antenna terminals.
Bend in the reverse direction.
b. With the antenna attached
to a wall.
Installation hole Mount on wall, etc.
AM outdoor antenna
Connection of AM antennas
1. Push the
lever.
2. Insert the
conductor.
3. Return the
lever.
NOTE
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not
disconnect the AM loop antenna.
• Make sure the AM loop antenna lead terminals do not
touch metal parts of the panel.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
ENGLISH
R
L
R
L
"6%*0
3-
*/
"6%*0
"69
065
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Multi-zone
ZONE2 out Connections
If another pre-main (integrated) amplifier is connected, the ZONE2 out connectors can be used to play a
different program source in ZONE2 the same time (vpage 54 ~ 57).
Connecting the Power Cord
Wait until all connections have been completed before connecting the power cord.
Power cord
To household
power outlet
(AC 120 V, 60 Hz)
Pre-main amplier
(ZONE2)
• These outlets supply power to external audio
Connection to the AC outlets
devices.
• The power supplied from these outlets turns on and
off together with the set’s power switch.
• Audio equipment with a total power consumption
of 120 W (1 A) can be connected.
NOTE
• Insert the AC plugs securely. Incomplete connections could cause noise.
• Only use the AC outlets to plug in audio devices. Do not use them as power supplies for hairdryers or
anything other than audio equipment.
Once Connections are Completed
Turning the Power On (vpage 43)
Input
Infrared
retransmitter
Output
Infrared
sensor
Extension jack for future use.
NOTE
• For the audio output, use high quality pin-plug cords so that no induction humming or noise is produced.
• For instructions on installing and operating separately sold devices, refer to the respective devices’
operating instructions.
• To conduct multi-zone playback, see “Amp Assign / Multi-zone Connections and Operations” (vpage 54 ~
57).
uiop
ENTER
[MODE
SELECTOR 1]
ENTER, opRETURN
uiMENU
uiop
RETURN
ENTER
MENU
[Front]
[Rear]
Menu Operations
With the AVR-888, settings and operations for most functions can be
performed by operating while looking at the menus displayed on the
monitor screen.
Operations
The same operation is possible on the main unit or remote control
unit.
Press MENU.
The menu is displayed.
1
b To operate from the remote control unit, be sure to set the [MODE
SELECTOR 1] to “AUDIO”.
Press ui to select the item you want to set, then
2
press ENTER.
Press ui again to select the item you want to set,
3
then press ENTER.
To change the setting:
4
Press ui to select the item you want to change, then
press o p to change the setting.
b To return to the previous item, press RETURN.
b Select “Default Yes”, then press o to reset to the default setting.
Example of Display of Default
Values
In lists of selectable items or adjustable ranges, the item
surrounded by a border is the default value.
[Selectable items]
A B A + B
ENGLISH
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
About the button names in these explanations
< > : Buttons on the main unit
[ ] : Buttons on the remote control unit
Button name only:
Buttons on the main unit and remote control unit
Press ENTER to enter the setting.
5
Press MENU to fi nish.
6
When MENU is pressed, the settings made up to that point are entered
and the settings menu screen turns off.
0
0
ENGLISH
MENU
1.Auto Setup
2.Manual Setup
3.Input Setup
4.Parameter
5.Information
* ME N U
A ut o S e t u p
Q
* St a r t M e n u
S ta r t •
QQ
* D i s t a n c e
E
U n i t : M e t e r • –F e e t
WQ
1-1.Start Menu
Step1:Speaker Detection
at ear height at
Front Sp. A
Amp Assign
Start
Cancel
Please place microphone
main listening position.
3-1.Assign
Digital In : OPT1
iPod Dock : None
2-1-3.Distance
Set The Distance To
Meters : Feet
Each Speakers
Do You Prefer
In Meters? / In Feet?
* As s i g n
D ig i t a l : • O PT 1 –
EQ
* Re n a m e : D V D
R en a m e • – C l ea r
Default
: DV
3-3.Rename
Yes
DVD
Default
: DVD-3930
3-3.Rename
Yes
DVD
* Re n a m e : D V D
• D V ¡ –
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Examples of On-screen Display and Front Display
Some typical examples are described below.
GOn-screen displayHGFront displayH
Screen title
Menu number
Submenu title
Press o to execute
Currently selected line
Current setting
Press op to change the setting
Press op to select one or the other
Use ui to input characters.
Use op to change the character input
position.
When highlighted, press i to select
“Default Yes”.
Loading...