Page 1
• Carefully read these instructions before
using this product.
• Do not attempt to repair the unit
yourself; an after-sales service is available.
RADIO TYBOX
This thermostat lets you put your heating system in
Comfort or Economy mode.
In automatic mode, the override function allows
you to switch from Comfort to Economy mode (or vice
versa) until the next programmed change.
NOTE: depending on the configuration during
installation, your unit will continuously
display the temperature setting or the
room temperature.
To change these settings,
refer to the “Installation instructions” or contact our
customer service department or your installer.
This mode is used to choose a temperature
setting that remains constant.
Turn the dial to .
This mode shuts down your
heating system.
Turn the selector dial to .
This mode protects your home from
frost if you are absent for
several days.
Turn the dial to .
Turn the dial to .
To exit the mode, turn the dial.
Depending on the system configuration (menu 1-08),
“conf” may be displayed for the setting.
This temperature setting cannot be modified.
If this is the case, the Comfort temperature
setting can be adjusted on your heat emitter
(thermostatically controlled valve).
Turn the selector dial to PROG.
The default programme is a Comfort period from
06:00 to 23.00.
1. Create your programme
The programme begins on day 1 at midnight.
Press the or buttons to create your
various Economy or Comfort periods.
2. Confirm and copy the programme
Hold down the OK button for 3 seconds to confirm
and copy the programme you created to the next day.
3. Confirm the programme
Press the OK button to confirm and go to programming for the next day.
OR
Check your programme
Press the button repeatedly to check the
Comfort and Economy periods you have created.
Press OK to check the next day.
Exit programming mode
Turn the dial to another mode.
NOTE: The programme can be weekly or daily
depending on the configuration during
installation. Likewise, this programming may be
done in increments of one hour, 30 minutes,
or 15 minutes.
To change these settings, refer to the “Installation
instructions” or contact our customer service
department or your installer.
1. P re se nt at ion
3. Override
6. Absence mode 7. Shutdown mode
8. Temperature setting
4. Timer mode 5. Continuous mode
9. Time setting 10. Programming
2. Automatic Mode
Time
Current day
Heating
demand
Room
temperature
Current day
programming
Current mode
Display in automatic mode
Override
Information
button
6h 8h
0h0h
17h15h30 23h
Example: It is 15:30 and you would like to switch
to Comfort mode before the set time (17:00).
Current day programming
Press the override
button.
Override
in progress
At 5pm, the programme will
return to the normal
schedule.
To cancel the current
override, press the button
once more.
Confirmation
Confirmation
Setting the temperature
(5 °C to 30 °C)
Sets the duration from 15 minutes to
72 hours (in increments of 15 minutes)
Return to
AUTO mode
at the end of
the countdown
This mode is used to choose a temperature
setting for a given amount of time.
Turn the dial to .
To change the mode in
progress, press the OK button
again.
To cancel the timer mode in
progress, turn the selector dial.
To exit the mode, turn the dial.
Confirmation
Temperature
setting
modification
Temperature
setting
Temperature
setting
selection
(5 °C to 30 °C).
Confirmation
To change the current mode,
press the OK button again.
To cancel the current mode, turn
the dial.
Sets the number of days (1 to 365).
For example, leaving on 1 March,
returning on 16 March: indicate
15 days of absence.
Automatic operation will resume at
midnight between 15 and 16 March.
Temperature setting
(5 °C to 15 °C)
Confirms and
begins
countdown
Return to
AUTO mode
at the end of
the countdown
Room
temperature
Configuration
menu access
button
(press and hold
for 5 seconds)
Comfort temperature setting
(5 °C to 30 °C in increments
of 0.5 °C)
Confirmation
proceed to Economy
temperature setting
Confirmation
Economy temperature setting
(5 °C to 30 °C)
Day
1st time slot
Sets a Comfort
period
Sets an
Economy period
6h 8h
0h0h
17h 23h
Example: Comfort from 6.00am to 8.00am and 5.00pm to 11.00pm
Press up to 06:00
Press up to 00:00
Copy and
confirm or confirm
Press up to 17:00
Press up to 08:00
Press up to 23:00
Time for
the
selected
slot
Checking
the various
or
periods
Programme
profile
Position of
selector dial
Change
mode
buttons
Selector
dial
Shutdown mode
Absence mode
Timer mode
Automatic mode
Continuous mode
Time setting
Programming
Temperature
setting
adjustment
RADIO TYBOX
TYBOX 811 W RF
Wireless programmable thermostat
for heating control
User guide
Delta Dore hereby declares that the equipment complies
with the essential requirements and other relevant provisions
of the R&TTE Directive 1999/5/EC.
The EC declaration of conformity for this equipment is available,
on request, from:
“Technical info” department
DELTA DORE - Bonnemain - 35270 Combourg (France)
Email: info.techniques@deltadore.com
Because of changes in standards and equipment, the characteristics given in the
text and the illustrations in this document are not binding unless confirmed.
*2702707_rev.1*
5
1
2
3
4
17
023
059
On the receiver:
- the green LED indicates that the product is
switched on,
- the red LED indicates the output status:
light on = ON, light off = OFF.
Turn the dial to AUTO.
Your thermostat will function according to the programming.
Page 2
The batteries need changing when the battery level
symbol appears (2 LR03 or AAA 1.5V alkaline
batteries).
Precautions must be taken:
- you have approximately 30 seconds to change
the batteries before the time is reset to zero
(if this happens, reset the date and time).
- properly align the +/- poles when placing
batteries in the unit,
- do not dispose of used batteries in unauthor ised
places (you should respect the environment by
taking the batteries to a suitable collection site),
- do not recharge them,
The device only displays the time and the room
temperature.
The transmitter is in screen saver display mode, but
all the heating features are running.
Press a button to “activate” the display.
The update can take a few seconds.
Nothing is displayed on the room
unit screen.
There is no power supply.
Check the batteries
.
The unit is in time setting mode.
You took too much time in changing the batteries.
Set the time. All the other settings have been kept.
When setting the time, the date is not displayed
for setting.
The transmitter is set to daily programming.
To switch to weekly programming, refer to the
installation instructions (menu 1-01).
This section is intended to help you quickly solve
the most common problems that you may
encounter with your product when using it.
If in doubt, if the problem persists or if it is not in
this list, please contact our customer services
department.
When creating a programme, the and
symbols do not appear on the screen.
Programme changes were not authorised during
installation.
Refer to the installation instructions (menu 2-01).
The temperature displayed does not match the
temperature measured in the room (thermometer).
Refer to the installation instructions (menu 2-02).
The programmes cannot be modified and the
temperature settings are limited (Comfort: 16 to
22 °C, Economy: 13 to 19 °C, Frost Protection:
5 to 11 °C).
Refer to the installation instructions (menu 2-01).
Your heating system is in Frost-Protection mode.
The thermostat is in the ,
, PROG
or
position.
The icon appears.
The batteries are low.
Change the batteries, ensuring they are in the correct
position.
13. Troubleshooting
11. Replacing the batteries
Battery level symbol
1
2
3 4
Separate the thermostat
from its base unit
Replace the batteries, taking care to
properly align the poles
Lock the thermostat
Place the thermostat
on its base unit
You can associate your programmer with the following
options:
12. Compatible home automation options
Type of
transmitter
associated
Resulting function
Opening
detector
“Waste prevention” function
Heating switches to Frost Protection
mode when a window is opened
(temperature set in mode).
Wireless
outdoor sensor
Indication of outside temperature
by consulting the information menu
(
i button).
X2D remote
control
Override : it switches the heating to
Comfort or Economy mode, until the
next program change.
Alarm control
unit
Association of the alarm with the
heating
For example,
Alarm activated = heating switches to
Economy mode (vacant)
Telephone
transmitter
Remote control of the installation
For information about associating and
using home automation products,
contact:
“Technical info” department
DELTA DORE - Bonnemain
35270 Combourg (France)
Email: info.techniques@deltadore.com
Loading...