Delta 36-L31, 36-L51, 36-L53, 36-L31X, 36-L51X Instruction Manual

INSTRUCTION MANUAL

UNISAW

®

10" Left Tilting Arbor Saw

(Models 36-L31, 36-L51, 36-L53,

36-L31X, 36-L51X)

PART NO. 422-40-651-0017 - 05-16-03

Copyright © 2003 Delta Machinery

To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,
please call

1-800-223-7278 (In Canada call 1-800-463-3582).

2

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

This manual contains information that is important for you to know and understand. This information relates to protect­ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols to the right. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES - DEFINITIONS

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other masonry products, and

· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense

and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this
machine not be modified and/or used for any application other than that for which it was designed. If you have any
questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine
if it can or should be performed on the product.

Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

3

1. FOR YOUR OWN SAFETY, READ THE INSTRUCT-

TION MANUAL BEFORE OPERATING THE
MACHINE. Learning the machine’s application,

limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.

2. USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI
Z87.1 standards, hearing equipment should
comply with ANSI S3.19 standards, and dust mask
protection should comply with MSHA/NIOSH
certified respirator standards. Splinters, air-borne
debris, and dust can cause irritation, injury, and/or
illness.

3. DRESS PROPERLY. Do not wear tie, gloves, or
loose clothing. Remove watch, rings, and other
jewelry. Roll up your sleeves. Clothing or jewelry
caught in moving parts can cause injury.

4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp
or wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to
prevent tripping or placing arms, hands, and
fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating
and changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.

6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions
that may affect its operation. A guard or any other
part that is damaged should be properly repaired
or replaced. Damaged parts can cause further
damage to the machine and/or injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is
a potentially dangerous environment. Children and visitors
can be injured.

9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of
a power failure, move the switch to the “OFF”
position. An accidental start-up can cause injury.

10. USE THE GUARDS. Check to see that all guards
are in place, secured, and working correctly to
prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high
speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a
machine or an attachment to do a job for which it
was not designed. Damage to the machine and/or
injury may result.

13. USE RECOMMENDED ACCESSORIES. The use
of accessories and attachments not recom­mended by Delta may cause damage to the
machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See the Extension Cord Chart for the correct size
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to

hold the workpiece when practical. Loss of control
of a workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION

OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE. Feeding it from the other

direction will cause the workpiece to be thrown out
a high speed.

17. DON’T FORCE THE WORKPIECE ON THE

MACHINE. Damage to the machine and/or injury
may result.

18. DON’T OVERREACH. Loss of balance can make

you fall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if

the tool tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-

DED. TURN THE POWER OFF. Don’t leave the machine
until it comes to a complete stop. A child or visitor could
be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE

MACHINE FROM THE POWER SOURCE before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs. An
accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental

start-up of a machine by a child or visitor could
cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while

operating power tools may result in injury.

24. THE DUST GENERATED by certain woods and

wood products can be injurious to your health.
Always operate machinery in well-ventilated areas,
and provide for proper dust removal. Use wood
dust collection systems whenever possible.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

4

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

ADDITIONAL SAFETY RULES

FOR CIRCULAR SAWS

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1. DO NOT OPERATE THIS MACHINE until it is
assembled and installed according to the

instructions.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,
instructor, or another qualified person if you are
not familiar with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended
electrical connections.

4. USE THE GUARDS WHENEVER POSSIBLE.
Check to see that they are in place, secured, and
working correctly.

5. AVOID KICKBACK by:
A. keeping blade sharp and free of rust and pitch.
B. keeping rip fence parallel to the saw blade.
C. using saw blade guard and spreader for every

possible operation, including all through
sawing.

D. pushing the workpiece past the saw blade prior

to release.

E. never ripping a workpiece that is twisted or

warped, or does not have a straight edge to
guide along the fence.

F. using feather boards when the anti-kickback

device cannot be used.

G. never sawing a large workpiece that cannot be

controlled.

H. never using the fence as a guide when

crosscutting.

I. never sawing a workpiece with loose knots or

other flaws.

6. ALWAYS USE GUARDS, SPLITTER, AND ANTI-
KICKBACK FINGERS except when otherwise
directed in the manual.

7. REMOVE CUT-OFF PIECES AND SCRAPS from
the table before starting the saw. The vibration of the
machine may cause them to move into the saw
blade and be thrown out. After cutting, turn the
machine off. When the blade has come to a

complete stop, remove all debris.

8. NEVER START THE MACHINE with the workpiece
against the blade.

9. HOLD THE WORKPIECE FIRMLY against the miter
gauge or fence.

10. NEVER run the workpiece between the fence and a
moulding cutterhead.

11. NEVER perform “free-hand” operations. Use either
the fence or miter gauge to position and guide the
workpiece.

12. USE PUSH STICK(S) for ripping a narrow
workpiece.

13. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a
hand to move into the blade.

14. KEEP ARMS, HANDS, AND FINGERS away from
the blade.

15. NEVER have any part of your body in line with the
path of the saw blade.

16. NEVER REACH AROUND or over the saw blade.

17. NEVER attempt to free a stalled saw blade without
first turning the machine “OFF”.

18. PROPERLY SUPPORT LONG OR WIDE
workpieces.

19. NEVER PERFORM LAYOUT, assembly or set-up
work on the table/work area when the machine is
running.

20. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs.

21. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.

22. ADDITIONAL INFORMATION regarding the safe and
proper operation of this machine, including a safety
video, is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851
(www

.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please refer
to the American National Standards Institute ANSI

01.1 Safety Requirements for Woodworking Machines
and the U.S. Department of Labor OSHA 1910.213
Regulations.

5

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3­prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating between 150

- 250 volts, inclusive:

If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. C, the
machine will have a grounding plug that looks like the
plug illustrated in Fig. C. Make sure the machine is
connected to an outlet having the same configuration as
the plug. No adapter is available or should be used with
this machine. If the machine must be re-connected for
use on a different type of electric circuit, the re­connection should be made by qualified service
personnel; and after re-connection, the machine should
comply with all local codes and ordinances.

IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

3. Permanently connected machines:
If the machine is intended to be permanently connected,

the machine should be connected to a grounded metal
permanent wiring system, or to a system having an
equipment-grounding conductor.

1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment­grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.

Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment­grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.

Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. C.

Repair or replace damaged or worn cord immediately.

POWER CONNECTIONS

MOTOR SPECIFICATIONS

Your machine is wired for 230 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.

Fig. C

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.

EXTENSION CORDS

FOREWORD

The Delta Unisaw is a 10" left tilting arbor saw. The Delta Unisaw features set the standards in the table saw industry.

A RIP FENCE ASSEMBLY IS NOT PACKAGED WITH THE PRODUCT. YOU MUST

INSTALL AND USE A

RIP FENCE SYSTEM FOR RIPPING OPERATIONS.

Fig. D

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 240

up to

50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG

6-10 240

up to

50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG

10-12 240

up to

50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG

12-16 240

up to

50 14 AWG
12-16 240 50-100 12 AWG
12-16 240

GREATER THAN 100 FEET NOT RECOMMENDED

FUNCTIONAL DESCRIPTION

FIVE HORSEPOWER MOTORS

The motors supplied with single phase, 5 horsepower Unisaws are designed to be operated from a 220-240 volt power
system.

The 5 horsepower Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they are permanently connected to
the building electrical system, extension cords cannot be used with the 5 horsepower Unisaw.

THREE PHASE OPERATION

Three phase Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they must be permanently connected
to the building electrical system, extension cords cannot be used with three phase Unisaws.

MAGNETIC PUSH BUTTON CONTROLS

If you purchased the Unisaw with a magnetic starter, transformer and overload protection (LVC), refer to the separate
electrical instruction manual supplied with the machine. These Unisaws are not supplied with a power cord. They must
be permanently connected to the building electrical system and grounded according to the National Electrical Code.
These connections should be made by a qualified electrician. Since they must be permanently connected to the
building electrical system, extension cords cannot be used with these Unisaws.

NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION

MODEL 36-L31. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY

NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED

TO ILLUSTRATE TECHNIQUE ONLY.

6

7

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.

REMOVE THE STYROFOAM PACKING AND ANY OTHER LOOSE ITEMS FROM THE INSIDE OF THE
SAW CABINET. THE MOTOR COVER MUST BE REMOVED IN ORDER TO REMOVE ITEMS FROM INSIDE THE SAW
CABINET. TO REMOVE THE MOTOR COVER, REMOVE THE 1/4-20x5/8" HEX HEAD SCREW FROM LOCATION
(B) FIG. 1, AND PUSH MOTOR COVER TO ONE SIDE TO DEPRESS CLIPS, AND PULL MOTOR COVER OFF. SEE
SECTION “MOTOR COVER”.

IMPORTANT: The saw is shipped with the saw arbor in the 45 degree position. NOTE: THE HAND WHEEL MUST BE
ASSEMBLED TO THE SAW, SEE THE SECTION “BLADE TILTING HANDWHEEL”, THEN PROCEED WITH THE
FOLLOWING. Loosen locking knob on the handwheel, and turn handwheel until the saw arbor is in the 90 degree

position and remove the styrofoam packing from inside the saw cabinet. Tighten locking knob.

UNISAW PARTS

3

4 5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22
23

24

25

26

27

28

29

31

32

33

34

35

30

Fig. 1

Fig. 2

Fig. 1

1. Unisaw

2. Switch (shown with a GPE switch)

Fig. 2

3. Extension wing (2)

4. Handwheel

5. Blade guard and splitter assembly

6. Upper bracket for splitter

7. Lower bracket for support rod

8. Support rod

9. 7/8" Open end arbor wrench

10. 7/8"x1/2" Closed end arbor wrench

11. Dust chute

12. Miter gage

13. Cap for miter gage handle

14. Handle for miter gage

15. Handwheel lock knob

16. 1/8" Hex wrench

17. 5/64" Hex wrench

18. Hanger for rip fence (2)

19. 7/16-20x1¼" Hex head screw (6)

20. 5/16-18x1" Hex head screw (4)

21. 5/16-18x1" Flat Head Screw (1)

22. #10x1/2" Hex washer head screw (8)

23. 10-32x1/2" Pan head screw (2) ( for use w/ LVC models only)

24. 3/4" I.D. Fiber washer (1)

25. 5/8" I.D. Internal tooth washer (1)

26. 7/16" I.D. Flat washer (6)

27. 5/16" I.D. Flat washer (2)

28. 5/16" I.D. Flat washer (1) (for use w/ GPE models only)

29. 5/16" I.D. Lockwasher (3)

30. 1/4" I.D. Fiber washer (1)

31. 13/64" I.D. Flat washer (2) (for use w/ LVC models only)

32. 5/8-18 Jam nut (1)

33. 5/16-18 Hex nut (1) (for use w/ GPE models only)

34. 1-3/8" Key (1)

35. Spring clip (2) (for use w/ LVC models only)

1

B

2

8

ASSEMBLY

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL
THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE
INSTRUCTION MANUAL.

BLADE TILTING
HANDWHEEL

1. Install fiber washer (A) Fig. 3, on the blade tilting
handwheel shaft (B). Install key (C), into shaft keyway.

2. Place handwheel (D) on shaft (B) Fig. 3. Make sure
the groove (E), in the handwheel lines up with the key (C).

3. Push the handwheel snugly against the fiber washer
and tighten the set screw.

4. Install lock knob (F) Fig. 4, into threaded end of the
shaft (B). Hand-tighten lock knob at this time.

Fig. 3

Fig. 4

EXTENSION WINGS

NOTE: CHECK TO SEE WHAT TYPE OF STARTER
BOX WAS SHIPPED WITH YOUR SAW (GPE OR LVC).
A GPE STARTER HAS ROUND “ON” AND “OFF”
BUTTONS. A LVC STARTER HAS RECTANGLE “ON”
AND “OFF” BUTTONS.

NOTE FOR GPE STARTER BOX: If your Unisaw was
shipped with an GPE starter box, the GPE “ON/OFF”
switch must be removed from the left side of the
Unisaw. When assembling the left extension wing, do
not install the front screw and washer at this time, it
will be installed when assembling the on/off switch.

NOTE FOR LVC STARTER BOX: If your Unisaw was
shipped with an LVC starter box, the LVC “ON/OFF”
switch must be removed from the left side of the
Unisaw. Save the hardware that attached the LVC
“ON/OFF” switch to the Unisaw because it will be
used to re-attach the “ON/OFF” switch to the left
extension wing in the section “ASSEMBLING LVC
ON/OFF SWITCH.”

Assemble the extension wing (A) Fig. 5 , to the left side of
the saw table using the three 7/16"-20x1¼" hex head
screws (B) and 7/16" flat washers supplied. NOTE:

MAKE SURE FRONT EDGE OF WING IS FLUSH TO
OR SLIGHTLY BEHIND THE FRONT EDGE OF THE
TABLE. Use a straight edge (C) Fig. 6, to make sure the

extension wing (A) is level with the saw table before
tightening the screws (B) Fig. 5.

Assemble the right extension wing in the same manner.

Fig. 5

Fig. 6

C

A

A

B

C

D

E

F

B

A

B

9

LVC STARTER BOX
TO CABINET

If you purchased the machine with magnetic push
button electrical controls (LVC), the saw is shipped with
the starter box completely wired to the switch and
motor. However, the starter box must be mounted to the
saw cabinet. To assemble the starter box (A) Fig. 7, to
the saw cabinet, proceed as follows:

1. Place a 1/4" lockwasher then a 1/4" flat washer onto
a 1/4-20x1/2" hex head screw. From the inside rear of
the saw cabinet, insert the 1/4-20 x 1/2" hex head screw
into the hole (B) Fig. 7, in the cabinet. Repeat this
process for the two remaining screws.

2. Line up the three tapped holes (C) Fig. 7, in the
starter box with the screws and secure the starter box
(A), to the saw cabinet.

3. Figure 8 illustrates the starter box (A) assembled to
the saw cabinet.

Fig. 7

Fig. 8

A

C

B

A

LVC ON / OFF SWITCH

1. Locate the LVC switch and hardware that was
removed in the section “ EXTENSION WING.”

2. Mount the switch bracket (C) Fig. 9, to the inside of
through hole D) on the left front edge of the extension
wing with the hardware that was removed.

NOTE: If you have a GPE switch see “GPE ON/OFF
Switch” instructions.

Fig. 9

D

C

A