INSTRUCTION MANUAL
24 3/4" Planer
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
(Model 22-610, Three Phase)
PART NO. 428-08-651-0001 06-15-05
Copyright © 2005 Delta Machinery
2
TABLE OF CONTENTS
Read and understand all warnings and operating instructions before using any tool or equipment. When
using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Delta Machinery strongly recommends
that this product NOT be modified and/or used for any application other than for which it was designed.
If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery
and we have advised you.
Online contact form at www
.deltamachinery.com
Postal Mail: Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)
Information regarding the safe and proper operation of this tool is available from the following sources:
Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851
www
.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201
American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www
.ansi.org
ANSI 01.1Safety Requirements for Woodworking Machines, and
the U.S. Department of Labor regulations www
.osha.gov
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover
3
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this
information.
SAFETY GUIDELINES - DEFINITIONS
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/OSHA
approved, properly fitting face mask or respirator when using such tools.
CALIFORNIA PROPOSITION 65
4
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION
MANUAL BEFORE OPERATING THE MACHINE.
Learning the machine’s application, limitations, and
specific hazards will greatly minimize the possibility of
accidents and injury.
2. WEAR EYE AND HEARING PROTECTION.
ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED
SAFETY EQUIPMENT. Eye protection equipment
should comply with ANSI Z87.1 standards. Hearing
equipment should comply with ANSI S3.19 standards.
3. WEAR PROPER APPAREL. Do not wear loose cloth-
ing, gloves, neckties, rings, bracelets, or other jewelry
which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering to contain long hair.
4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp or
wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or
placing arms, hands, and fingers in danger.
5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK CONDI-
TION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.
6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, and any other conditions that may
affect its operation. A guard or any other part that is
damaged should be properly repaired or replaced.
Damaged parts can cause further damage to the
machine and/or injury.
7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a
potentially dangerous environment. Children and visitors can
be injured.
9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of a
power failure, move the switch to the “OFF” position.
An accidental start-up can cause injury.
10.
USE THE GUARDS. Check to see that all guards are
in place, secured, and working correctly to reduce
the risk of injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high speed,
causing injury.
12. USE THE RIGHT MACHINE. Don’t force a machine or
an attachment to do a job for which it was not
designed. Damage to the machine and/or injury may
result.
13. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by
Delta may cause damage to the machine or injury to the
user.
14. USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage, resulting in loss of
power and overheating. See the Extension Cord Chart
for the correct size depending on the cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to hold
the workpiece when practical. Loss of control of a
workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION OF
THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE
SURFACE. Feeding it from the other direction will cause
the workpiece to be thrown out at high speed.
17. DON’T FORCE THE WORKPIECE ON THE MACHINE.
Damage to the machine and/or injury may result.
18. DON’T OVERREACH. Loss of balance can make you
fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if the
tool tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
TURN THE POWER OFF. Don’t leave the machine until it
comes to a complete stop. A child or visitor could be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs. An accidental start-up
can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY REMOVING STARTER KEYS. The accidental start-up of a
machine by a child or visitor could cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A
moment of inattention while operating power tools may
result in injury.
24. USE OF THIS TOOL CAN GENERATE
AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE
SILICA DUST AND ASBESTOS DUST. Direct particles
away from face and body. Always operate tool in well
ventilated area and provide for proper dust removal.
Use dust collection system wherever possible.
Exposure to the dust may cause serious and permanent
respiratory or other injury, including silicosis (a serious
lung disease), cancer, and death. Avoid breathing the
dust, and avoid prolonged contact with dust. Allowing
dust to get into your mouth or eyes, or lay on your skin
may promote absorption of harmful material. Always
use properly fitting NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure, and wash
exposed areas with soap and water.
5
ADDITIONAL SPECIFIC SAFETY RULES
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
1. DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to
the instructions. A machine incorrectly assembled
can cause serious injury.
2. OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not thoroughly familiar with the operation of this machine.
Knowledge is safety.
3. FOLLOW ALL WIRING CODES and recommend-
ed electrical connections to prevent shock or electrocution.
4. KEEP KNIVES SHARP and free from rust and
pitch. Dull or rusted knives work harder and can
cause kickback.
5. NEVER TURN THE MACHINE “ON” before clearing
the table of all objects (tools, scraps of wood, etc.).
Flying debris can cause serious injury.
6. NEVER TURN THE MACHINE “ON” with the work-
piece contacting the cutterhead. Kickback can
occur.
7. SECURE THE MACHINE TO A SUPPORTING SUR-
FACE to prevent the machine from sliding, walking
or tipping over.
8. PROPERLY SECURE THE KNIVES IN THE CUTTER-
HEAD before turning the power “ON”. Loose
blades may be thrown out at high speeds causing
serious injury.
9. LOCK THE SPEED SETTING SECURELY before feed-
ing the workpiece through the machine. Changing
speeds while planing can cause kick-back.
10. AVOID AWKWARD OPERATIONS AND HAND POSI-
TIONS. A sudden slip could cause a hand to move
into the knives.
11. KEEP ARMS, HANDS, AND FINGERS away from
the cutterhead, the chip exhaust opening, and the
feed rollers to prevent severe cuts.
12. NEVER REACH INTO THE CUTTERHEAD AREA
while the machine is running. Your hands can be
drawn into the knives.
13. DO NOT STAND IN LINE OF THE WORKPIECE.
Kickback can cause injury.
14. ALLOW THE CUTTERHEAD TO REACH FULL SPEED
before feeding a workpiece. Changing speeds
while planing can cause kickback.
15. WHEN PLANING BOWED STOCK, place the concave
(cup down) side of the stock on the table and cut
with the grain to prevent kickback.
16. DO NOT FEED A WORKPIECE that is warped, con-
tains knots, or is embedded with foreign objects
(nails, staples, etc.). Kickback can occur.
17. DO NOT FEED A SHORT, THIN, OR NARROW WORK-
PIECE INTO THE MACHINE. Your hands can be
drawn into the knives and/or the workpiece can be
thrown at high speeds. See the “OPERATION” section of this instruction manual for details.
18. DO NOT FEED A WORKPIECE into the outfeed end of
the machine. The workpiece will be thrown out of
the opposite side at high speeds.
19. REMOVE SHAVINGS ONLY with the power “OFF” to
prevent serious injury.
20. PROPERLY SUPPORT LONG OR WIDE WORK-
PIECES. Loss of control of the workpiece can cause
serious injury.
21. NEVER PERFORM LAYOUT, ASSEMBLY or set-up
work on the table/work area when the machine is
running. Serious injury will result.
22. TURN THE MACHINE “OFF”, DISCONNECT IT FROM
THE POWER SOURCE, and clean the table/work
area before leaving the machine. LOCK THE
SWITCH IN THE “OFF” POSITION to prevent unauthorized use. Someone else might accidentally
start the machine and cause injury to themselves
or others.
23. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
refer to the American National Standards Institute
ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor
Regulations.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
6
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
POWER CONNECTIONS
MOTOR SPECIFICATIONS
The 22-610 has a 10 HP three phase motor that comes wired at 230 volts and 60 HZ alternating current. The motor
is also capable of being wired for 460 volt operation, but this connection must be done by a qualified electrician and
conform to the National Electric Code and all local codes and ordinances.
FOREWORD
FUNCTIONAL DESCRIPTION
NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THE CURRENT PRODUCTION
MODEL. ALL OTHER ILLUSTRATIONS CONTAINED IN THE MANUAL ARE REPRESENTATIVE ONLY
AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED
TO ILLUSTRATE TECHNIQUE ONLY.
The Delta Indusrial Model 22-610 is a 24
3
/4" Planer with a 10 HP, three-phase motor capable of 230 volt or 460 volt
operation with an LVC magnetic starter and automatic reset overload protection; 4-knife cutterhead, infeed and outfeed rollers, chipbreakers, dust chute, knife-setting gauge and wrench.
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
GROUNDING INSTRUCTIONS
These machines are not supplied with power cords and they are intended to be permanently connected to the building’s elecrical system. All wiring must be done by a qualified electrician and conform to the National Electric Code and all local codes
and ordinances. For wiring instructions, see section “ELECTRICAL CONNECTIONS” in this manual.
7
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor
paste wax.
CARTON CONTENTS
The 22-610 planer is shipped complete in one container mounted to a shipping skid. Remove the wooden crate from around the
machine. The planer is shipped with the motor, motor pulleys and belts assembled to the machine. Fig. 2, illustrates the loose items
supplied with the machine.
1. Planer
2. Cutterhead guard.
3. Dust chute
4. Knife guage
5. Open end wrenches
6. Hex wrenches
7. Gauge block
1
2
3
4
5
6
7
8
ASSEMBLY
ASSEMBLY TOOLS REQUIRED
ASSEMBLY TIME ESTIMATE - 2-3 hours
* Open end wrenches (supplied)
* Hex wrenches (supplied)
* Flat screwdriver (not supplied)
UNLOADING AND
POSITIONING MACHINE
This machine should be unloaded using a crane and
slings around and under the table on both sides, as
shown in Fig. 2. Lift the machine slowly, making sure it
is well balanced, and lower it carefully.
Using rollers or a similar hauling device, push the
machine to the desired working site. Once the machine
is in position it should be leveled and positioned on hard
rubber pads placed underneath the four corners.
Remove protective coating from the table, bed rolls,
feed rolls and cutterhead. This coating may be removed
with a stiff brush and/or soft cloth moistened with
kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
CARE MUST BE TAKEN WHEN CLEANING THE CUTTERHEAD AS THE KNIVES ARE IN THE
CUTTERHEAD AND THESE KNIVES ARE VERY SHARP.
After cleaning table, cover table surface with a good
quality paste wax.
Fig. 2
Fig. 3
ELECTRICAL CONNECTIONS
Before connecting your machine to an electrical power
system, make sure the motor rating agrees with the
electrical system it is to be connected to. The 24" Planer
is shipped wired for 230 volts, three phase operation.
If you desire to operate your planer at 460 volts, three
phase operation, refer to the Electrical Instruction
Manual supplied with your planer for detailed instructions on Changing Voftage of LVC Motor Starters. Three
STEPS must be followed when changing line voltage.
These steps are as follows:
1. Change leads in the motor junction box for the proper line voltage, as shown on the motor nameplate. Refer
to Fig. 3.
2. Move the transformer primary pigtail to the proper terminal corresponding to the new input voltage.
3. Change the heater elements in the overload block for
the proper voltage/amperage rating shown on the motor
nameplate.
These three steps are clearly explained in the electrical
instructions supplied with your planer.
9
To connect power to your machine, proceed as follows
for either 200-230/460 volts, three phase operation.
1. Remove the four screws, one of which is shown at
(A) Fig. 4, and remove cover (B).
2. Insert power line through entrance hole (E) and connect the three power lines to terminals L1, L2 and L3
(shown at C). The green ground wire should be connected to the ground terminal (J).
3. Replace cover (B) Fig. 4.
IMPORTANT: If after the machine is in operation, the
cutterhead turns in the wrong direction, interchange any
two of the three power lines (C) that are connected to
terminals L1, L2 and L3.
OVERLOAD PROTECTION
Your planer is provided with overload protection which will
shutoff the motor if the planer is overloaded or if line voltage falls below safe levels, lithe motor shuts off due to overloading or low voltage, let the motor cool three to five minutes. The overload block supplied with this planer will automatically reset itself and the machine can be started again
by pushing the start button. If the machine continually
shuts off due to overloading, the cause of overloading must
be corrected. If this happens, it is recommended you obtain
advice from a qualified electrician.
Fig. 4
Fig. 5
Fig. 6
Fig. 7
ASSEMBLING CUTTERHEAD GUARD
AND DUST CHUTE
To assemble the cutterhead guard:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Remove four screws and washers at (A) Fig. 6.
3. Place guard on planer cover (C) so that the holes in
the guard (B) align with the holes in the cover (C).
4. Replace screws and washer removed in Step 1.
5. Remove three screws (E) Fig. 7 on planer cover (C).
6. Place dust chute on cover so that the holes in the
dust chute (D) align with the holes in the cover (C).
7. Replace the screws and washers removed in Step 5.
8. The cutterhead guard (B) Fig. 7A and dust chute (D)
Fig. 7A should be arranged as shown in Fig. 7A
A
E
C
J
B
A
B
C
E
C
D
Fig. 7A
D
B
10
OPERATION
OPERATIONAL CONTROLS AND ADJUSTMENTS
STARTING AND STOPPING THE PLANER
The machine is started by pressing the green (shrouded) "ON" button (A) and stopped by pressing the red
(mushroom type) "OFF" button (B), as shown in Fig. 8.
Fig. 8
TABLE RAISING AND
LOWERING CONTROLS
DISCONNECT MACHINE FROM
POWER SOURCE
For fast easy changes in thickness settings to accommodate thick or thin stock, the table can be rapidly
raised or lowered by pulling up or pushing down on the
table raising and lowering control lever (C) Fig. 9. NOTE:
The machine must be turned "ON" and the feed rolls
engaged when doing this.
Fine adjustment of the table height can be made by
loosening lock knob (D) Fig. 9, and turning table raising
and lowering handwheel (E). Tighten lock knob (D) after
table adjustment is made. The handy English/Metric
Scale (F) indicates the desired table height setting.
The English/Metric scale and shelf (G) Fig. 10, located
on the front of the table is used to quickly determine the
thickness of stock, before or after planing, by simply
placing the stock on the shelf as shown in Fig. 10. This
enables you to quickly position the table for the next cut.
NOTE: The setting of the table to its final position should
always be made by raising the table to the desired setting and not lowering the table. This insures that all
backlash will be removed from the raising and lowering
screws.
FEED ROLL SPEED CONTROLS
Your planer is supplied with feed roll speeds of 25 and
46 feet per minute. When the feed roll lever (A) is in the
"up" position as shown in Fig. 11, the feed rolls are
engaged and the planer will feed. When the lever (A) is
in the "down" position the feed rolls are disengaged and
the planer will not feed. To disenguage the feed rolls, at
any time, simply push down on the engagement lever (A)
Fig. 11.
Fig. 9
Fig. 10
Fig. 11
B
A
F
D
E
C
A
G
11
Fig. 12
To change feed roll speeds, make sure the feed roll
engagement lever (A) Fig. 12, is disengaged (in the down
position) and open the left side door of the machine.
When the belt (C) is on the smallest step of the motor
pulley (D) and the largest step of the gearbox pulley (E),
the feed roll speed will be 25 feet per minute. When the
belt (C) is on the largest step of the motor pulley (D) and
the smallest step of the gearbox pulley (E), the feed roll
speed will be 46 feet per minute.
Fig. 13
Fig. 14
TABLE ROLLERS
Your planer is supplied with two table rollers (A) Fig. 13,
which aid in feeding the stock by reducing friction and
turn as the stock is fed through the planer. It is not possible to give exact dimensions on the proper height setting of the table rollers because each type of wood
behaves differently. As a general rule, however, when
planing rough stock the table rollers should be set HIGH
and when planing smooth stock the table rollers should
be set LOW.
To raise the table rollers (A) Fig. 13, turn adjustment
knob (B) clockwise. To lower table rollers (A) turn adjustment knob (B) counterclockwise.
ANTI-KICKBACK FINGERS
Anti-kickback fingers (A) Fig. 14, are provided on your
planer to prevent kickback. These fingers operate by
gravity and it is necessary to inspect them occasionally
to make sure they are free of gum and pitch so they
move independently and operate correctly.
E
C
D
A
A
A
12
Fig. 16
Fig. 17
Fig. 18
CHECKING AND ADJUSTING
BELT TENSION
DRIVE BELT TENSION: Proper drive belt tension is
obtained when there is zero deflection, using light finger
pressure, on drive belts (A) Fig. 16, midway between pulleys. If an adjustment is necessary, push down on lever
(B) Fig. 16, to disenguage feed roller. Loosen jam nut (C)
Fig. 17, located on top of motor (D) and turn adjustment
stud (E) right or left as needed until proper drive belt tension is obtained. Tighten jam nut (C) after adjustment is
made.
FEED ROLL BELT TENSION: Proper tension on feed
roll belt (F) Fig. 16, is obtained when there is approximately 1" deflection, using light finger pressure on feed
roll belt (F), midway between pulleys.
If an adjustment is necessary, change position of rod (B)
Fig. 18, in stud (G) by tightening and loosening two nuts
(H) until correct belt tension is obtained. Both nuts (H)
should be tight against stud (G) as shown in Fig. 18,
after adjustment is made.
E
A
F
B
C
D
H
G
H
B
13
CHECKING, ADJUSTING AND
REPLACING KNIVES
1. When checking, adjusting or replacing the cutter-
head knives on the planer, proceed as follows:
A. DISCONNECT MACHINE FROM
POWER SOURCE
B. Remove the top cover of the planer exposing the
cutterhead.
C. Check all four knives for proper setting using the
knife guage (A), as shown in Fig. 20. When the
guage (A) is placed on the cutterhead and the bottom of the two roll pins, one of which is shown at (B),
are against the edge of the slot (C) opposite the
knife, the knife should just contact the bottom of the
guage (D).
D. If any of the knives require an adjustment, slightly
loosen the knife locking bar of each of the four
knives by turning the knife locking screws (E) Fig.
20, into the locking bar just enough to relieve stress
in the cutterhead but not disturb the setting of the
four knives.
E. To adjust the knife that must be reset, loosen all of
that knife's locking screws (E) Fig. 20, by turning
them into the locking bar. As the knife locking bar
becomes loose, lifter springs under the knife will
raise the knife until it contacts the bottom of the
guage (D). Then snug up the knife locking bar by
lightly backing out the locking screws (E) against the
knife slot. IMPORTANT: AT THIS TIME, ONLY
TIGHTEN THE KNIFE INTO THE SLOT ENOUGH TO
HOLD IT IN POSITION.
F. If additional knives must be reset, repeat STEP C.
G. After all four knives are set with the screws just
snug, back out and tighten the locking screws, five
of which are shown at (E) Fig. 20, against the slot.
Start with the end screws first and proceed on alternate sides toward the center screws until the knife is
securely held in the cutterhead. Tighten the remaining three knives in the same manner.
2. IF THE KNIVES ARE TO BE
REMOVED FOR SHARPENING OR REPLACEMENT,
EXTREME CARE SHOULD BE TAKEN AS THE
KNIVES ARE VERY SHARP. TO REMOVE THE
KNIVES, WEAR GLOVES AND PROCEED AS FOLLOWS:
A. DISCONNECT MACHINE FROM
POWER SOURCE
Fig. 20
B. To remove each knife, loosen the knife locking bar,
by turning the locking screws, five of which are
shown at (E) Fig. 20, into the knife locking bar and
remove the locking bar, knife and springs located
under the knife.
C. Remove the remaining three knives in the same
manner.
D. Thoroughly clean the knife slots, knife bars, springs
and screws. If the threads appear worn or stripped
or if the heads are becoming rounded, replace them.
E. Inspect the cutting edge of the knives for nicks or
wire edge. Hone the knives slightly using a stone or
if the knives are to be sharpened, maintain a cutting
angle of 40 degrees.
F. Insert springs, knives and knife locking bars into all
four slots in the cutterhead. Push knives down as far
as possible and back out locking screws, five of
which are shown at (E) Fig. 20, just enough to hold
all four knives in the cutterhead.
G. Adjust all four knives as explained in Step 1.
B
A
D
E
E
C
14
Fig. 21
Fig. 22
Fig. 22A
LEVELING THE TABLE
The table must be parallel to the cutterhead knives. To
check and adjust, proceed as follows:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Remove the four screws that attach the top cover to
the planer and carefully remove the top cover.
3. Place a straight edge (A) Fig. 21, on the ground surfaces (B) of the planer, as shown.
4. Place the guage block (C) Fig. 21, on the table
directly underneath the straight edge at one side, as
shown, Raise the table until the guage block just touches the straight edge. Do not raise or lower the table any
further until the adjustment for leveling the table is completed.
5. Move the guage block (C) Fig. 21, to the opposite
(left end) of the table and check to see if the table is the
same distance from the straight edge as on the right
side.
6. Place the straight edge (A) on the two ground surfaces (B) of the outfeed end of the planer as shown in
Fig. 22. Check both ends of the table with guage block
(C) to see if table is level.
7. If the table is low or high at any of the four points
checked with the guage block in Figs. 21 and 22, locate
the post directly underneath the end of the table that
must be adjusted. Then loosen the three screws, two of
which are shown at (A) Fig. 22A, and turn flange (B) to
raise or lower the table at that end.
A
C
B
A
C
B
A
A
B
15
Fig. 23A
Fig. 23B
Fig. 23D
Fig. 23C
CHECKING AND ADJUSTING
BED ROLL HEIGHT
The height of the bed rolls (A) and (E) Fig. 23A, should
be set between .002" and .004" above the table surface,
with the bed rolls at their lowest position. To check the
infeed bed roller height setting, proceed as follows:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Turn height adjustment knob (B), counterclockwise
as far as it will go.
3. Place a straight edge (C), across the infeed and out-
feed rollers on the left side of the table as shown.
4. With a feeler guage (D), measure the gap between
the table surface and the straight edge (C) near the
infeed roll (E).
5. If an adjustment to the infeed roller (E), is necessary,
loosen set screw (F) Fig. 23B, located underneath the
left front end of the table.
6. Turn adjustment collar (G) Fig. 23B left or right as
needed to attain proper height adjustment.
7. Tighten set screw (F) Fig. 23B after adjustment is
made.
To check the outfeed roller height setting, proceed
as follows:
1. With a feeler guage (H) Fig. 23C, measure the gap
between the table surface and the straight edge (C) near
the outfeed roller (E).
2. If an adjustment to the outfeed roller is necessary,
loosen jam nut (K) Fig. 230, located on the left side of
machine under the table, and turn collar (L) right or left
as needed until the outfeed roller is adjusted properly.
3. Tighten jam nut (K) Fig. 23D.
C
A
B
D
E
G
F
C
H
E
K
L
16
Fig. 24B
Fig. 25
Fig. 26
ADJUSTING PRESSURE BAR
IMPORTANT: THE PRESSURE BAR IS SET AT THE
FACTORY AND SHOULD NOT NEED ASJUSTMENT.
BUT WHEN KNIVES ARE SHARPENED OR
REPLACED THE PRESSURE BAR SETTING SHOULD
BE CHECKED AND ADJUSTED IF NECESSARY.
The pressure bar is located directly behind the cutterhead and rides on the planed surface of the stock,
pressing the stock down on the table. If the stock does
not feed, the pressure bar is set too low. If the stock has
chatter marks, the pressure bar is set too high. The pressure bar must be parallel to the knives and set .040"
below the cutting circle.
To check and adjust the pressure bar, proceed as follows:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Remove the four screws that attach the top cover (A)
Fig. 24A to the planer and carefully remove the top
cover.
3. Make certain the knives are adjusted properly as
previously explained under CHECKING, ADJUSTING
AND REPLACING KNIVES.
4. Place the guage block (A) Fig. 24B, on the table
directly underneath the cutterhead as shown. Place a
.040" feeler guage (B) Fig. 24B, on top of the guage
block and raise the table until the knife (C) just touches
the feeler guage when the knife is at its lowest point.
5. Next, set the feeler guage aside and move the
guage block (A) Fig. 25, directly underneath the pressure
bar (B) on one end of the table. The pressure bar (B)
should just touch the guage block (A). Check the pressure bar at the opposite end of the table in the same
manner.
6. If the pressure bar must be adjusted, remove screw
(D) Fig. 26. Loosen screw (E) Fig. 26A, three or four
turns. Turn screw (F) Fig. 26A clockwise to raise the bar
or counter clockwise to lower the bar. The bottom of
pressure bar should just touch the gauge block (A) Fig.
25.
8. Then tighten screw (E) Fig. 26A until it bottoms and
then loosen it two complete turns. Replace screw (D)
Fig. 26A.
9. This adjustment to the pressure bar should be made
on the opposite end of the planer In the same manner.
B
A
C
A
B
D
Fig. 24A
A
Fig. 26A
E
D
F
E
17
ADJUSTING THE CHIPBREAKER
The chipbreaker is located on the top of the planer and
extends down around the front of the cutterhead. The
chip-breaker segments raise as stock is fed through and
"break or curl" the chips the same as the plane iron cap
on a hand plane. The bottom of the chipbreaker must be
parallel to the knives and set .040" below the cutting circle. To check and adjust the chipbreaker, proceed as follows:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Remove the four screws that attach the top cover to
the planer and carefully remove the top cover.
3 Make certain the knives are adjusted properly as previously explained under CHECKING, ADJUSTING AND
REPLACING KNIVES.
4. Place the guage block (A) Fig. 29, on the table direct-
ly underneath the cutterhead as shown. To adjust the
chipbreaker, place a .040" feeler gauge (B) Fig. 29, on
top of the guage block and raise the table until the knife
(C) just touches the feeler guage when the knife is at its
lowest point.
5. Move the guage block (A) Fig. 30, underneath each
chipbreaker segment (B) as shown. The bottom of each
chipbreaker segment should just touch the top of the
guage block.
6. If an adjustment to any of the chipbreaker segments
is necessary, loosen the corresponding lock nut, such as
(C) Fig. 31, and turn adjusting screw (D) in or out as
required. Then tighten lock nut (C).
7. Spring tension on the chipbreaker segments is prop-
erly set when the head of corresponding screw (E) Fig.
32, is two complete turns below surface of casting (F).
Fig. 29
Fig. 30
A
B
A
C
B
Fig. 31
Fig. 32
D
C
F
E
18
ADJUSTING SPRING TENSION
ON FEED ROLLERS
The outfeed roll (A) Fig. 33, and infeed roll (not visible)
are those parts of your planer that feed the stock while
it is being planed. The feed rolls are under spring tension
and this tension must be sufficient to feed the stock uniformly through the planer without slipping but should not
be too tight that it causes damage to the board. The tension should be equal at both ends of each roll.
To adjust spring tension on the infeed roll, turn screws
(B) Fig. 33, right or left until they are flush with top of
casting (C). To adjust spring tension on the outfeed roll
(A), turn screws (D) until they are 2 to 3 complete turns
below surface of casting (E).
Fig. 33
Fig. 34
Fig. 35
Fig. 36
Fig. 37
ADJUSTING OUTFEED ROLLER
The outfeed roller (A) Fig. 34, should be .035" below the
cutting circle. To check and adjust the outfeed roll, proceed as follows:
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Make certain the knives are adjusted properly as
previously explained under CHECKING, ADJUSTING
AND REPLACING KNIVES.
3. Place the guage block (C) Fig. 35, on the table
directly underneath the cutterhead, as shown. Place a
.035" feeler guage (B) on top of the guage block and
raise the table until the knife (A) just touches the feeler
guage when the knife is at its lowest point.
Do not move the table any further until the adjustment is
completed.
4. Place the guage block underneath outfeed roll (A)
Fig. 36. The feed roll should just touch the top of the
guage block (C) which would be .035" below the cutting
circle. If an adjustment is necessary, loosen locknut (D)
Fig. 37, and turn adjusting screw (E) until the outfeed roll
just touches the top of the guage block. Repeat at opposite end of feed roll.
D
E
D
E
C
B
C
B
A
A
B
C
A
C
A
E
D
19
Fig. 38
Fig. 39
Fig. 40
ADJUSTING CHIP DEFLECTOR
1. DISCONNECT MACHINE FROM
POWER SOURCE
2. Remove the cutterhead guard.
3. The edge (C) of the chip deflector (A) Fig. 38, should
be adjusted so it is a minimum of .040" and a maximum
of .080" away from the cutting circle. Place a feeler
gauge between the knife and the edge of the chip
deflector as shown in Fig. 38. If an adjustment is necessary, loosen three screws (B) and move chip deflector.
ADJUSTING TABLE HEIGHT SCALE
The table height scale is adjusted at the factory to indicate the distance from the table to the cutting circle
(depth of cut).
To check and adjust the pointer, proceed as follows:
1. Run a piece of wood part way through the planer
and stop the machine.
2. Measure the thickness of the finished piece. If nec-
essary, loosen two screws (A) Fig. 39 adjust pointer (B)
and retighten screws (A).
GAUGE BLOCK
A gauge block has been supplied with your planer; however, if it is ever necessary to make a gauge block out of
hardwood, follow the instructions shown in Fig. 40.
4"
1
/4"
45°
2"
3"
4"
1
1
/2"
1
/2"
GRAIN
C
A
B
A
B
20
When using your machine, follow these few simple steps for achieving the best results.
1. T
rue Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire
surface is flat.
2. Plane
to Thickness – Place the side you planed in STEP 1 face down and feed the board through the planer. Plane
until this side is flat, then plane both sides of the board until you are satisfied with the thickness. Make thin cuts,
and alternate sides with each pass. If, during the planing operation, you notice the board twisting, warping, or bowing, repeat STEP 1 and true up one face.
3. When planing long stock, provide table extensions to support the infeed and outfeed end of the workpiece.
4. Plane with the grain only, and keep planer table clean. Occasionally, wax the table surface to reduce friction during the planing operation.
5. Cr
oss-cut to Final Length – Cross-cut lumber to final length.
THE KNIVES ON THE PLANER WILL NOT WEAR EVENLY IF THE WOOD IS FED THROUGH THE
SAME SPOT ON THE TABLE EVERY TIME. FEED THE WOOD THROUGH THE PLANER AT DIFFERENT SPOTS ON THE TABLE TO HELP ELIMINATE UNEVEN WEAR OF THE KNIVES.
MACHINE USE
TROUBLESHOOTING
For assistance with your machine, visit our website at www
.deltamachinery.com
for a list of service centers or call
the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
MAINTENANCE
LUBRICATION
Your machine requires lubrication as follows:
1. The four grease fittings, one of which is shown at (A)
Fig. 41, located at the base of the four table posts are to
be lubricated every 100 hours of operation with an automotive type lithium grease or equivalent.
2. As required, lubricate the four table raising and lowering screws, three of which are shown at (B) Fig. 42,
with an automotive type lithium grease or equivalent.
3. The gear box oil should be changed once a year
using extreme pressure gear oil, available from Delta in
one pint cans under part number 999-01-013-1210. The
gear box drain plug is shown at (C) Fig. 43. The oil fill
screw is shown at (B) and the oil level indicator is shown
at (A) Fig. 43.
Fig. 41
Fig. 43
Fig. 42
A
B
B
A
C
21
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable
• Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site
www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested
with this product, use of such accessories could be hazardous. For safest operation, only
Delta recommended accessories should be used with this product.
ACCESSORIES
SERVICE
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted defect
which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other
than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s
exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability,
fitness for purpose, or otherwise, are expressly disclaimed by Delta.
WARRANTY
KEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed
air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They could
possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while
using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the
prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in
the line.
SURFACE LUBRICATION
Apply household floor paste wax to the machine table and
extension table or other work surface weekly.
PROTECTING CAST IRON FROM RUST
To clean and protect cast iron tables from rust, you will
need the following materials: 1 pushblock from a jointer,
1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1
can of WD-40®, 1 can of degreaser, 1 can of TopCote
®
Aerosol. Apply the WD-40 and polish the table surface
with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the TopCote
®
accordingly.
22
NOTES
23
NOTES
The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,
Contractor’s Saw II™, Delta
®
, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,
Grip Vac™, Homecraft
®
, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,
MORTEN™, NETWORK™, OMNIJIG
®
, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFES-
SIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic
®
, Q-3®&(design), QUICKSAND®&(design), QUICKSET™,
QUICKSET II
®
, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®,
Sawbuck™, Sidekick
®
, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company
®
&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQ-
BUSTER
®
, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®,
Versa-Feeder
®
, VERSA-PLANE®, WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE
• DELTA)
Parts and Repair Service for Porter-Cable •Delta Machinery are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta)
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable
·
Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable
·
Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable
·
Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable
·
Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable
·
Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable
·
Delta más cercano.
ARIZONA
Phoenix 85013-2906
4501 N. 7th Ave.
Phone: (602) 279-6414
Fax: (602) 279-5470
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Diego 92111
7290 Clairemont Mesa Blvd.
Phone: (858) 279-2011
Fax: (858) 279-0362
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
COLORADO
Denver 80223
700 West Mississippi Ave.
Phone: (303) 922-8325
Fax: (303) 922-0245
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33634
4909 West Waters Ave.
Phone: (813) 884-0434
Fax: (813) 888-5997
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
KANSAS
Overland Park 66214
9201 Quivira Road
Phone: (913) 495-4330
Fax: (913) 495-4378
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
MASSACHUSETTS
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
Eden Prairie 55344
9709 Valley View Road
Phone: (952) 884-9191
Fax: (952) 884-3750
MISSOURI
St. Louis 63146
11477 Page Service Drive
Phone: (314) 997-9100
Fax: (314) 997-9183
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
OHIO
Columbus 43229
1948 Schrock Road
Phone: (614) 895-3112
Fax: (614) 895-3187
Parma Heights OH 44130
6485 Pearl Road
Phone: (440) 842-9100
Fax: (440) 884-3430
OREGON
Portland 97230
14811 North East Airport Way
Phone: (503) 255-6556
Fax: (503) 255-6543
PENNSYLVANIA
Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77022-2122
536 East Tidwell Rd.
Phone: (713) 692-7111
Fax: (713) 692-1107
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
PC7.2-0105-149
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
Loading...