Delonghi VLP 400, VL 400, VL 300, VLP 400 R Instructions Manual

7

A) DESCRIPTION Tabletop models

1) Front guard

2) Guard surround

3) Propeller cap

4) Propeller

5) Guard lock nut

6) Rear guard

7) Handle

8) Motor shaft

9) Oscillating knob

10) Motor housing

11) Tilt adjustment

12) Base

13) Power cable

14) Feet

15) Controls

16) Safety screws plus nut

17) Catch

B) DESCRIPTION Floor standing models

1) Front guard

2) Guard surround

3) Propeller cap

4) Propeller

5) Guard lock nut

6) Rear guard

7) Handle

8) Motor shaft

9) Oscillating knob

10) Motor housing

11) Tilt adjustment

12) Control box

13) Fixing screws

14) Inner tube

15) Height adjustment ring

16) Outer tube

17) Finish ring

18) Base

19) Power cable

20) Control panel

21) Infrared receiver (electronic models only)

22) Remote control unit (electronic models
only)

23) Safety stop plus nut

24) Catch

Description

GB

GB

8

A1) ASSEMBLING TABLETOP MODELS

• Unscrew the guard lock nut (5) from the
motor shaft (8).

• Thread the rear guard (6) onto the motor
shaft (8) with the handle (7) facing
upwards. Line up the holes in the centre of
the guard with the pins projecting from the
front of the motor housing.

• Fix the rear guard (6) by screwing the
guard lock nut (5) up as far as it will go.

•After removing the thread guard from the
motor shaft, thread the propeller (4) onto
the motor shaft (8) and fix by screwing up
the propeller cap (3) in an anticlockwise
direction.

• Check propeller rotation by hand. Make
sure there is no friction with the guard lock
nut (5). The propeller should rotate freely.
If this is not the case repeat the assembly
operations from the beginning.

•Mount the front guard (1) onto the rear
guard (6) by attaching it to the hook (fig.

1). Line up the two holes in the two guard
surrounds (2) and fix with the safety screws
and nut (16) (fig. 2). Lock the guards in
place using the catches (17).

B1) ASSEMBLING FLOOR STANDING MODELS

• Remove the four screws from the base. Put
together the bars A and B (fig. 3) with the
feet facing downwards. Line up the four
holes in the bars with those in the bottom
tube and screw up the four screws tightly.

• Loosen the fixing screw (13), remove the
height adjustment ring (15) and thread the
finish ring (17) onto the outer tube (16),
pushing down as far as it will go. Reposition
the height adjustment ring (15), pull out
the inner tube (14) until you reach the
required height then block the height by
tightening the ring (15) firmly.

• Thread the control box (12) onto the inner
tube and tighten the fixing screw (13).

• For the subsequent assembly operations,
follow the instructions given in the previous
paragraph B in the same sequence.

C) OPERATING INSTRUCTIONS TABLETOP MODELS

After plugging into the mains socket, turn the
fan on by pressing any of the buttons. Select
the required speed by pressing the corre­sponding button. Turn the fan off using the "O"
button. For oscillating operation, push the
oscillating knob (9). For steady operation,
extract the oscillating knob (9) by pulling
upwards. To adjust the tilt of the fan, use the
tilt adjustment (11) on the top of the base. This
should be done with the fan off only.

C1) OPERATING INSTRUCTIONS FLOOR STANDING
MODELS

MODEL WITHOUT REMOTE CONTROL

For operation, see paragraph C "Operating
Instructions Tabletop Models".

MODELS WITH REMOTE CONTROL
OPERATING FROM THE CONTROL PANEL (20)

After plugging into the mains socket, turn the
fan on by pressing the "SPEED" button.
The appliance comes on at medium speed
"M" and after three seconds is set automati­cally to minimum speed "L". Each time you
press the "SPEED" button, the speed of the fan
is adjusted from minimum speed (L), through
medium speed (M) to maximum speed (H).
Turn the fan off using the "O" button.

USING THE TIMER

With the fan on, press the "TIME" button. Each
time you press the "TIME" button, the required
shut-down time can be set (1h/2h/4h/8h).
Note: pressing the "O" button eliminates all
shut-down programming previously set.

USING THE REMOTE CONTROL UNIT (22)

All the above functions can also be control­led from the remote control unit. When using
the remote control unit, remember to point it
towards the receiver (21).

Assemblign and operating