DELONGHI HHP1500K Installation Manual

MICATHERMIC FLAT PANEL RADIATOR

INSTRUCTIONS FOR USE

SAVE THESE INSTRUCTIONS

PANEL RADIANTE MICATHERMIC

INSTRUCCIONES PARA EL USO

REPASE Y GUARDE ESTAS INSTRUCCIONES

LEA CUIDADOSAMENTE ESTE INSTRUCTIVO

ANTES DE USAR SU APARATO

MODEL/MODELO

HHP1500K

Register this product online and receive a free trial issue of Cook's Illustrated.
Visit www.delonghiregistration.com
Visit www.delonghi.com for a list of service centers near you. (U.S. Only)

Registre este producto en línea y reciba un ejemplar gratis de Cook's Illustra­ted. Visite www.delonghiregistration.com
Visite www.delonghi.com para ver la lista de centros de servicios cercanos a
usted. (Solamente en los Estados Unidos)

ELECTRONIC CHARACTERISTICS/CARACTERISTICAS ELECTRICAS

120V˜60Hz 1500W

2

Voltage

Wattage

See rating label

3,28 ft

2,30 ft

Function selector

Thermostat

Pilot light

Fig.1

Fig.2

Fig.3

Fig.4

0,45 ft

3

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce risk of fire, electric
shock, and injury to persons, including the following:

1. Read all instructions before using this heater.

2. If your appliance is equipped with a polythene tape used as carry handle, remove it before connecting
appliance to the outlet.

3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handle when
moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and cur­tains at least 3 feet (0,9 m) from the front and top of the heater and keep them away from the sides and rear.

4. The appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

5. Extreme caution is necessary when any heater is used by or near children and whenever the heater is left
operating and unattended.

6. Always unplug heater when not in use.

7. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been

dropped or damaged in any manner. Return heater to authorized service facility for examination,
electrical or mechanical adjustment, or repair.

8. Do not use outdoors. Household use only.

9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never loca­te heater where it may fall into a bathtub or other water container.

10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange

cord away from traffic area and where it will not be tripped over.

11. To disconnect heater, turn controls to off, then remove plug from outlet.

12. Connect to properly polarized outlets only.

13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock, fire, or damage the heater.

14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.

15. A heater has hot or arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or

flammable liquids are used or stored.

16. Use this heater only as described in this manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.

17. To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet
(receptacle) or into another outlet (receptacle) wired into the same circuit.

18. It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which becomes hot to
the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or recep­tacles should be replaced prior to further use of the heater. Plugging the heater into a worn outlet/recep­tacle/ may result in overheating of the power cord or fire.

19. This heater is not intended for use with an extension cord or outlet strip. Plug the cord directly into an
appropriate wall outlet.

20. Be sure that the plug is fully inserted into an appropriate outlet. Please remember that outlets also deterio­rate due to aging and continuous use: check periodically if signs of overheating or deformations are evi­denced by the plug. Do not use the outlet and CALL your electrician.

21. Check that neither the appliance nor the power cable have been damaged in any way during transportation.

22. Make sure that no pieces of polystyrene or other packaging material have been left on the appliance.
It may be necessary to pass over the appliance with a vacuum cleaner.

23. When switching on the appliance for the first time, allow it to run at full power for at least two hours
to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to emit small cracking sounds when you
turn it on for the first time.

24. CAUTION: to prevent electric shock match wide blade of plug to wide slot, then fully insert.

25. Do not cover the appliance while it is functioning in order to avoid overheating which may cause
risk of fire.

SAVE THESE INSTRUCTIONS

4

HOW TO USE YOUR MICATHERMIC FLAT PANEL RADIATOR

Thank you for choosing this De'Longhi heater. Please read this instruction booklet carefully
before using this heater. By doing so, you will obtain optimum results with maximum safety.

1. General instructions

Remove the heater from the packaging. Check that neither the heater nor the power cable has
been damaged during transport. Do not operate the heater if damaged. Your heater is suitable
for either freestanding or wall mounted usage. Do not assemble the feet if wall mounting.

2. Electrical connection

- Before plugging in the appliance, check that your power supply voltage is the same as that

shown on the rating label of the appliance and that the power supply is able to withstand
the power consumption (Watts) shown on the rating label.

- If using more than one appliance at a time, it is important to ensure that the power supply

is able to withstand all combined power requirements.

3. Free standing operation

To fit the feet to the appliance, proceed as follows:
Fix the foot with the attached screws, as shown in fig.1.
CAUTION: NEVER

use this heater without feet when not wall-mounted.

ASSEMBLY KIT

The wall mounting kit contains:
4 x screws for wall mounting
4 x anchors (0.6 x 30) for wall mounting
1 x mounting bracket

REQUIRED TOOLS FOR ASSEMBLY AND ESTIMATED ASSEMBLY TIME

Screwdriver PH 2 x 100 (Phillips type)
Estimated assembly time: 30 minutes

4. Wall Mounted Installation

Before installing the unit , make sure of the following:

a.The heater is not located directly below a power outlet.
b.The power outlet can be easily reached by the plug after installation.
c. No electric cables or other pipes could be damaged during the installation.
d.Keep away from curtains or inflammable materials.

To wall mount, proceed as follows:
For brick walls use a 15/64" (6 mm) concrete drill bit . For plasterboard or false (hollow)
walls, it is recommended to use appropriate screws and anchors (not supplied).

1. Before drilling the wall, mark out a template using the mounting bracket respecting the
minimum distances as shown in fig.2/3.

2. Drill the wall where previously marked, and insert the plastic anchors.

3. Fix the bracket with the 2 screws provided (see fig.4).

4. Hang the heater on the bracket.

5. Mark out the 2 lower fixing points (fig.2). Remove the appliance, drill the lower holes and
insert the wall anchors.

6. Now, you can hang back the heater to the bracket and fix the lower part of the appliance
with the 2 remaining screws.