DDSX 220WF-WH
DEHUMIDIFIER
EN
pag. 6
B1 B2 CB C1 C2 C3 C6C4 C5 B3 B4
C9C10
B7 B6C7C8C11C12
2
B5
A1
A6
A
B
A2
A3
A4
A5
A8
A7
A2
A10 A11
A9
A12
3
1
2
3
10
4
7
11
5
8
6
9
12
4
13
14
15
16
19
17
18
5
1. FUNDAMENTAL SAFETY WARNINGS
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If the power cord is damaged, it must be replaced by the manufacturer or the
manufacturer’s Customer Experience in order to avoid all risk.
As the appliance is powered by electricity, the possibility of
electrical shock cannot be excluded.
The following safety precautions must therefore be followed:
• After removing the packaging, check the condition of the
appliance. If in doubt, do not use the appliance and contact
professionally qualied personnel.
• Before use, always check the condition of the power cord.
• It is dangerous to modify or alter the characteristics of the
appliance in any way.
• This appliance must be connected to an ecient
“grounding” system. Have the electrical system checked by
a qualied electrician.
• Before each cleaning or maintenance operation, always
disconnect the plug from the power outlet.
• Never submerge the appliance in water.
• Do not use the appliance outdoors.
• Do not obstruct the entrances and exits of air.
• When the appliance is connected to the mains, keep the
following safety rules in mind:
• Do not touch the appliance with wet or damp hands;
• Do not use the appliance with bare or wet feet;
• Do not pull on the power cord or appliance to detach the
plug from the power outlet;
• Do not move the appliance by pulling the power cable.
• keep the appliance far from the reach of children;
• Do not insert foreign bodies into the appliance;
• Do not insert metal objects into the apertures.
Danger! Rotating parts; contact with the internal fan could
cause electric shock or injury.
Do not drink the water collected from the appliance or use
it as animal drinking water.
• do not leave the appliance exposed to atmospheric agents;
• If you wish to permanently eliminate the appliance,
after disconnecting the plug from the power outlet it is
recommended to make it unusable by severing the power
cord.
• In the event of a fault and/or malfunction, turn the
appliance o without tampering with it. For all repairs,
contact an authorised technical service centre only and
request the use of original spare parts and accessories.
• Avoid the use of power cord extensions.
1.1 Designated use
This appliance must be used exclusively for the intended purpose
for which it was designed, specically to dehumidify domestic
environments. All other uses are considered improper and
therefore hazardous. The manufacturer shall not be held liable
for any damage caused by improper, erroneous and irresponsible
use, and/or due to repairs made by unqualied personnel.
1.2 Installing the appliance
• The appliance must be installed in compliance with
national standards regulating electrical systems.
• Do not install the appliance in rooms containing gas, oil or
sulphur or near sources of heat.
• Do not use the appliance on sloping surfaces.
• Keep the appliance at least 50 cm away from ammable
substances (alcohol, etc.) or pressurised containers (e.g.
aerosol cans).
• Do not rest objects on top of the appliance.
• When transporting, the appliance must be kept upright or
• resting on one side. Before transporting, drain all the water
from the appliance. After transporting, wait at least one
hour before turning on the appliance.
1.3 Enviromental information
• The materials used for packaging can be recycled. You
are therefore recommended to dispose of them in special
dierentiated waste collection containers.
10
Specic information regarding appliances with
R290 refrigerant gas
• Thoroughly read all of the warnings.
• When defrosting and cleaning the appliance, do not
use any tools other than those recommended by the
manufacturing company.
• The appliance must be placed in an area without any
continuous sources of ignition (for example: open ames,
gas or electrical appliances in operation).
• Do not puncture and do not burn.
• Refrigerant gases can be odourless.
• The appliance must be installed, used and stored in an area
that is greater than 4 m
• This appliance contains R290 refrigerant gas.
(For more details on the refrigerant, see back cover).
• R290 is a refrigerant gas that complies with the European
directives on the environment. Do not puncture any part of
the refrigerant circuit.
• If the appliance is installed, operated or stored in a nonventilated area, the room must be designed to prevent the
accumulation of refrigerant leaks resulting in a risk of re
or explosion due to ignition of the refrigerant caused by
electric heaters, stoves, or other sources of ignition.
• The appliance must be stored in such a way as to prevent
mechanical failure.
• Individuals who operate or work on the refrigerant
circuit must have the appropriate certication issued by
an accredited organisation that ensures competence in
handling refrigerants according to a specic evaluation
recognized by associations in the industry.
• Repairs must be performed based on the recommendations
from the manufacturing company.
Maintenance and repairs that require the assistance of
other qualied personnel must be performed under the supervision of an individual specied in the use of ammable
refrigerants.
• The materials used for packaging can be recycled. You are
therefore recommended to dispose of them in special differentiated waste collection containers.
• Do not use the appliance outdoors.
• Do not obstruct the entrances and exits of air.
• Do not use the appliance in laundry rooms.
2
.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Please note:
These safety warnings are valid for all De’Longhi
dehumidifyers.
Keep this leaet together with the instructions
accompanying the appliance.
If the appliance is passed to other persons, they must also be
provided with this Instruction for Use.
3. BEFORE USE
Important!
Store the packaging material (plastic bags, styrofoam) far from
the reach of children.
CHOKING HAZARD. The appliance might contain small parts.
Some of those small parts might be required to get disassembled
during cleaning and maintenance operations. Handle with care
and keep small parts out of reach of children.
3.1 Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged. Contact
De’Longhi Customer Services.
3.2 Connecting the appliance
Before plugging the appliance into the outlet, check that:
• The mains voltage corresponds to the operating voltage
stated on the rating plate.
• The mains socket and the electrical supply line are
adequate for the required load.
• The power outlet matches the plug. If this is not the case,
have the plug replaced by a qualied electrician
• The outlet is properly grounded.
4. CLEANING AND MAINTENANCE
Always remove the plug from the power socket before
performing any cleaning or maintenance operations. For safety
reasons, never wash the dehumidier using a water jet.
Clean the air lter regularly.
5. DISPOSAL
The appliance must not be disposed of with
household waste, but taken to an authorised
waste separation and recycling centre.
2. GENERAL INFORMATION
2.1 Instruction for Use
Read all the Instruction for Use carefully before using the
appliance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
11
Read the separate safety instructions before using the appliance.
DE’LONGHI
DEʼLONGHI
6. DESCRIPTION
6.1 Description of appliance (A)
A1. Air outlet louver
A2. Lifting handles
A3. Room sensor air intake
A4. Castors
A5. Water level viewing window
A6. Condensate collection tank
A7. Epa lter
A8. Silver ion dust lter
A9. Filter housing cover
A10. Continuous drain rubber stopper
A11. Continuous drain cap
A12. Continuous drain hose
6.2 Description of control panel (B)
B1. ON/STAND-BY button
B2. Ventilation button
B3. Dehumidifying button
B4. Wi-Fi button
B5. Swing button
B6. Dry button
B7. Timer button
6.3 Description of display(C)
C1. Full tank alarm
C2. EPA lter present symbol
C3. Ventilation mode active
C4. % Relative Humidity
C5. Wi-Fi symbol
C6. App control symbol
C7. Dr y mode active
C8. Hours
C9. Dehumidifying mode ac tive
C10. Low temperature alarm
C11. Remote timer symbol
C12. Local timer symbol
7. DOWNLOAD THE APP!
This appliance can also be used with the "De'Longhi Comfort
APP" that is available on Google Play or can be downloaded
from the App Store®.
To gain access to all functions, a Wi-Fi local network (Home
WLAN) with Internet access is required. Moreover, check that
there are no impediments to Internet access: Firewall, Proxy,
authentications, etc.
8. DRAINING THE CONDENSATE WATER
The condensate can be drained in 2 ways:
8.1 Draining into the tank
The condensate is drained directly into the tank (A6).
When the tank is full, the appliance stops and the display (C)
shows the tank alarm (C1). Proceed as follows:
1. Remove the tank (g. 1) and empty it into a sink or bathtub.
2. Replace the tank in its housing, making sure the handle is
properly positioned (g. 2).
Continuous external draining
8.2
If the appliance is used for long periods of time without the
possibility to regularly empty the tank, the continuous drain
function should be used.
Proceed as follows:
1. Remove the continuous drain cap (A11) from the spout,
turning it in an anti-clockwise direction, then remove the
continuous drain rubber stopper (A10) from the opening
(g. 3) (Watch out for any leaking water!)
2. Attach the condensate drain hose (A12) to the spout (g.
4).
3) Make sure the hose is positioned below the spout (g. 5) or
the water will ow back into the tank of the appliance.
Also make sure there are no kinks in the hose.
9. MODE SELECTION
Connect the appliance to the mains supply. Upon rst use, the
symbol will appear on the display and at the same time,
an acoustic signal will sound to indicate that the appliance is in
stand-by mode.
1. To turn the appliance on, touch the button (B1).
The appliance will operate in the previously set mode and
the air outlet louver (A1) will open in a preset position (g.
6).
2. If there is a blackout, when the power is restored the
appliance will resume operation in the previously set
operating mode.
Please note:
If the
needs to be emptied or properly positioned (see paragraph “3.1
Draining into the tank”).
symbol (C1) appears on the display, the tank (A6)
12
Air ltration
If the EPA lter (A7) is installed, in addition to operating in the
preset mode, the appliance will also lter the air in the room. In
this case, the
The lter is designed to last up to 9 months, based on 8-hour
daily usage at medium working load.
To maintain the eciency of ltration, see paragraph “5.3
Replacing the EPA lter”.
symbol (C2) will appear on the display.
9.1 Dehumidifying mode
1. Touch the button (B3). The symbol (C9) will
blink on the display (g. 7).
2. The display shows the previously set relative humidity
value. When the symbol blinks, the setting can be
changed by repeatedly touching the
There are 9 dierent relative humidity settings ranging
from 30% (dry environment) to 70% (humid environment).
Depending on the environmental conditions, it may not be
possible for the appliance to reach the minimum settable
value. In these cases, it is recommended the heat the
environment that needs to be dehumidied.
3. When the symbol stops blinking, the display shows the
percentage of relative humidity in the room. The appliance
may take a few seconds to display the value of the relative
humidity in the room.
4. When the room reaches the preset relative humidity level,
the appliance stops dehumidifying and operates at a very
slow ventilation speed.
button.
9.2 Dry mode
1. Touch the button (B6). The display shows the
symbol (C7) (g. 8).
Please note:
The appliance automatically operates at the maximum
dehumidifying capacity. Recommended for particularly humid
environments or to dry laundry more quickly.
9.3 Ventilation mode
1. Touch the button (B2). The display shows the
symbol (C3) and the selected speed (g. 9).
2. When the symbol blinks, the ventilation speed can be
adjusted by repeatedly pressing the
display shows the number corresponding to the selected
speed (1 ⇒ LOW; 2 ⇒ MED; 3 ⇒ HIGH).
button. the
9.4 Swing function
1. Press the button (B5) . The air outlet louver (A1)
moves up and down, evenly distributing the air ow in the
room (g. 10).
2. To stop the louver in the desired position, touch the same
button again.
9.5 Timer function
The timer can be used to delay appliance start-up and shutdown. This will avoid energy wastage, ensuring the appliance
operates only when needed.
The timer function can be programmed from either the control
panel or the app.
• If programmed from the control panel: the display shows
symbol (C12) (g. 11).
the
• If programmed from the app: the display shows the
symbol (C11) (g. 12). To programme the timer from the
app, follow the instructions provided in the app.
How to programme delayed start-up
1. With the appliance in stand-by (
button (B7): the display will show the symbol and the
number relative to the selected hours (g.11);
2. Set the desired number of hours by repeatedly touching
the
3. After a few seconds, the appliance will return to stand-by
mode and the
4. After the programmed time, the appliance will turn on in
the previously set operating mode.
How to programme delayed shut-down
1. While the appliance is running, touch the
(B7): the display shows the symbol and the relative
number of selected hours (g. 11);
2. Set the desired number of hours by repeatedly touching the
3. After a few seconds, the display returns to the current
operating mode and the symbol remains lit.
4. After the programmed time, the appliance will
automatically turn o.
Please note:
• Once the timer has been programmed, to see the remaining
time until start-up or shut-down, touch the
button once.
• To deactivate the timer function, press the
twice. The symbol on the display will turn o.
button.1, 2, 4, 6, 8, 12 hours can be selected.
symbol will remain lit on the display.
button. 1, 2, 4, 6, 8, 12 hours can be selected.
), touch the
button
button
9.6 Wi-Fi function
The appliance has a built-in Wi-Fi function. To activate or
deactivate this function, hold the
until the appliance emits two beeps. When the Wi-Fi function is
active, the display will show the Wi-Fi symbol (C5) with the
following operating modes:
FIXED
-
this means the Wi-Fi functions are active and the
“Home WLAN” has been found
SLOW FLASHING
-
this means the appliance is searching for the
“Home WLAN”
13
button (B4) pressed
FAST FLASHING
this means the “Home WLAN” has not been found
or has not been set.
“APP CONTROL” ICON
When the APP CONTROL icon appears
this means the last command was received via
Remote connection (e.g. APP).
If the saved “Home WLAN” setting needs to be changed, proceed
as follows:
1. Hold the
a long beep is heard;
2. Use the app to set the new “Home WLAN” settings in the
unit.
button pressed for about 20 seconds until
10. CLEANING AND MAINTENANCE
• Always disconnect the appliance from the mains before
carrying out cleaning operations (g. 13).
• Never submerge the appliance in water.
10.1 Cleaning the cabinet
• Never pour water directly over the appliance (g. 14).
• Never use petrol, alcohol or solvents.
• Never spray insecticides or similar substances as these may
deform the plastic.
• Clean the surfaces of the appliance using a soft cloth and do
not use abrasive sponges as these may scratch the surfaces
themselves (g. 15).
10.2 Cleaning the dust or silver ion lter
The frequency of cleaning will depend on the frequency of use:
if used daily, it is recommended to clean the lter every week.
• Remove the lter housing cover (A9) from the appliance
(g. 16).
• Extract the dust lter (g. 17).
• Remove any dust from the lter using a vacuum cleaner
(g. 18).
• If the dust lter is very dirty, rinse it well with warm water.
The water temperature must not exceed 40° C.
• Leave it to dry completely, then put it back into place.
10.3 Replacing the EPA lter
The appliance will automatically remind you when the EPA lter
(A7) needs to be replaced . After a preset number of operating
hours, the display shows the blinking symbol (C2) to indicate
that the lter needs to be replaced.
Always use original De’Longhi lters.
• Remove the lter housing cover (A9) (g. 16).
• Extract the used lter (g. 19) and replace it with a new
one.
• Close the lter housing cover (with the dust lter (A8)
inserted).
• Reset the lter alarm by holding the button (B2)
pressed for at least 10 seconds until you hear a long beep.
Please note:
symbol is intended only as a guide and it may be
the
necessary to replace the EPA lter more frequently, depending
on the air quality.
For long periods of downtime
• Disconnect the appliance from the mains and empty the
tank (A6).
• Clean the dust lter (A8) and re-insert it.
• Cover the appliance with a plastic bag to protect it from
dust.
11. TECHNICAL SPECIFICATIONS
Power supply voltage See rating plate
Input power “
Maximum input power “
Defrost device Yes
Hygrometer Yes
Fan speed 3
Air lter Yes
Frequency: 2400/2483.5 MHz
Maximum transmission power 10 mW
Operating limits:
Temperature 2°C - 30°C
Relative Humidity 30 - 90%
14
12. ALARMS SHOWN ON DISPLAY
ALARM CAUSE SOLUTION
Tank (A6) missing or incorrectly
positioned
Tank full Empty the tank (see paragraph “3.1 Draining into the
Place the tank back in its correct position (see paragraph “3.1 Draining into the tank”)
tank”)
Room temperature too low (see operating limits in chap. “6. Technical
Specications”)
Humidity in room too low or too high for
correct measuring (see operating limits
in chap. “6. Technical Specications”)
Faulty probe Call Service Centre
Wi-Fi interface not working properly Turn the appliance o and disconnect the plug from
After a preset number of operating hours,
the symbol (C2) blinks on the display
to indicate that the EPA lter (A7) needs
to be replaced.
Increase the room temperature if possible
Move the appliance to another room with humidity
and temperature levels within the operating limits: if
the problem persists, call the Service Centre.
the power socket. Wait a few minutes, then re-insert
the plug: if the problem persists, contact the Service
Centre.
Replace the EPA lter (see para. “5.3 Replacing the
EPA lter”).
If the EPA lter has recently been replaced, reset the
alarm (see para. “5.3 Replacing the EPA lter”)
13. TROUBLESHOOTING
Below is a list of possible malfunctions.
If the problem cannot be resolved using the proposed solution,
contact the Service Centre.
PROBLEM CAUSE SOLUTION
The appliance is operating in dehumidifying mode, but the humidity does not
decrease
The lter is clogged Clean the dust lter (para. “5.2 Cleaning
the dust lter”) and check whether the
EPA lter needs replacing (para. “5.3 Replacing the EPA lter”)
Either the temperature or humidity in the
room is too low
The set relative humidity level is too high Set a lower humidity value (see para-
In certain conditions the appliance will
not dehumidify: check the operating limits of the appliance (see chap. “6. Technical Specications”). In certain cases, it is
recommended to heat the room needing
to be dehumidied.
graph “4.1 Dehumidifying mode”).
15
Gas charge
De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com
571481XXXX_00_1219
Loading...