Delonghi DCH7993ER.BC Instruction manuals

DESCRIPTION

(see g. 1)

A ON/STAND-BY button
B +/- adjustment buttons
C MODE button (selects the operating mode)
D “ECO plus” button
E Timer button
F Swing button
G Remote control receiver
H Remote control
I Indicator light
J Air intake grille
K Filter

USE

Installation

The appliance can be used on any horizontal surface.
Do not overload the electrical circuit. Avoid using the same
socket for other appliances.

by pressing the adjustment buttons + and – (B):

- Heating
The appliance operates at minimum power, automati-

- Heating
The appliance operates at medium power.

- Heating
The appliance operates at high power to heat the room

- To turn the appliance o, press the ON/STAND-BY

either °C or °F. To change the unit of measurement for the
temperature, press the + button for a few seconds, then
release.

Silent+

cally reducing energy consumption and noise level. The
tones emitted by the commands are lower than in other
modes for even more silent operation.

rapidly.

button (A). The display may visualize a countdown for
about 6 seconds.

Please note: Room temperature can be displayed in

Electrical connection

- Before plugging the appliance into the mains socket,
check that the mains power supply corresponds to the
value indicated on the rating plate and that the mains
power supply is adequate for the load.

- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/
EEC ON RADIO INTERFERENCE SUPPRESSION.

Operation and use

- Plug into the mains socket.

- The appliance emits a beep. The indicator light (I) comes
on and remains lit while the appliance is powered.

- The appliance switches to stand-by. A dot ashing
on the display means the tip over device has been
activated. See paragraph: “Safety functions”.

- Press the ON/STAND-BY (A) to turn the appliance on.
It begins heating the room according to the current
settings.

- Press the MODE button (C) to select one of the following
operating modes:

- Fan

In this mode, only the fan operates and the appliance

does not heat the room.

- Freeze prevention

In this mode, the appliance keeps the room at a

temperature of 7°C to avoid freezing.

- Heating

In this mode, the desired temperature can be selected

“ECO plus” function
The “ECO plus” function is available in Heating 1, 2 and 3 modes
only. To activate the function, press the “ECO plus” button (D).
When this function is active the appliance automatically sets
the most appropriate power level to guarantee optimum
comfort while reducing energy consumption.
While the “ECO plus” function is active, the appliance may
switch automatically to a lower heating power than the one
displayed. This may happen a number of times in an hour.

Swing button

To distribute the air ow over a wider surface, press the swing
button (F) . The appliance starts swinging to the right
and left. To stop the appliance in the desired position, simply
press the swing button (F) again.

Digital 24 h timer

This function can be activated from any operating mode.
Auto-start: with the appliance in STAND-BY, press the timer
button (E). The symbol is displayed together with
the time remaining before the appliance comes on.
To adjust the timer, use the adjustment buttons + and - (B),
then wait a few seconds for the setting to be memorised. The
stand-by light (I) is displayed together with the symbol,
indicating that the timer has been set.
When the programmed time is reached, the appliance comes
on with the settings used during the previous period of
operation.

7

Auto-o: with the appliance on, press the timer button

(E). The symbol is displayed together with the time
remaining before the appliance goes o.
To set the timer, use the adjustment buttons + and - (B),
then wait a few seconds for the setting to be memorised.
The current settings are displayed again, together with the

symbol indicating that the timer has been set.
When the programmed time is reached, the appliance goes
o automatically. To go back to operation without the timer,
press the timer button (E) twice.
The timer symbol disappears from the display.

USING THE REMOTE CONTROL

The functions on the remote control are the same as those on
the appliance control panel.
For a description of the functions, see the “Operation and use”
section on the previous page.

Inserting or replacing the batteries

- The remote control is

provided with a lithium
battery CR2032. To let
the appliance function,
remove the battery cover
strip, by pulling it.

- To replace the batteries,

remove the battery cover
by rotating it. Replace the
battery paying attention to
respect the right polarity as shown in gure 1.

- Replace the cover rotating it towards the position .

- Old batteries must be removed and disposed o in

accordance with current legislation as they are harmful
to the environment.

Fig. 2

TECHNICAL CHARACTERISTICS

Supply voltage See rating plate
Absorbed power “

MAINTENANCE

- Always unplug from the mains socket before cleaning.

- During the season when the appliance is in use, clean

the air intake and outlet grilles regularly using a vacuum
cleaner.

- To clean the lter, remove the rear grille by pulling it

outwards.

Remove the dust lter which retains impurities in the air

drawn in from the room, blow on it lightly then replace
in the appliance.

- Never use abrasive powders or solvents to clean the

appliance.

8