MAIN FAN HEATER ELEMENTS (Fig. 1)
GB
A Control panel flap G Control panel for models without timers
B Wall-mounting bracket H Function selector
C Control panel for models with timers I Thermostat
D Electronic timer L Thermostat indicator light
E Function selector M Grille rotation grips
F Thermostat N Adjustable ventilation grilles
O Cable winder
P Base
INSTALLATION
The fan heater can easily be positioned on any supporting surface or installed on the wallmounting bracket supplied.
Proceed as follows to wall-mount the heater:
- Fit the wall-mounting bracket, respecting the minimum distances shown in Fig. 2. The
room heater must be outside the protective area (Fig. 4) when installed in a bathroom or
shower room and under all circumstances away from taps, basins and showers, etc.
- Remove the screw in the bottom of the base and unclip the base, pulling it out from the
rear.
- Clip the fan heater onto the bracket, slanting it slightly (Fig. 3) and then fix it in place using
a screwdriver, turning the screw in the top part of the mounting bracket clockwise.
ELECTRIC CONNECTION
- Before fitting the plug in the mains socket, make absolutely sure that the voltage of your
mains electricity supply is the same as the value in V shown on the heater.
- Make sure the mains socket has a capacity of 10/16 Amperes.
- This appliance complies with EEC Directive 89/336, relating to electro-magnetic
compatibility.
FAN HEATER CONTROLS
FUNCTION SELECTOR
Heating with r.h. fan
Heating with l.h. fan
Heating with
both fans
4
Unit off
Fans only
Digital display
Pilot light
Anti-freeze function
ELECTRONIC TIMER
Reset pushbutton
Sliding starter indicator
THERMOSTAT
Summer use
Heating
Programming
pushbuttons
fig. 5
OPERATION AND USE
Heating and setting the thermostat
- Turn the function selector knob to one of the 3 different heating positions available (Fig.
5).
- Turn the thermostat knob clockwise to its maximum position.
- On models fitted with electronic timer, slide the starter indicator (fig.5) to position “I”; the
indicator lamp will come on.
When the room has reached the temperature desired, set the thermostat by slowly turning
the thermostat knob counter-clockwise until you hear the click which switches off the heater
and then stop turning the knob immediately.
The temperature set in this way will be automatically maintained at a constant level by the
thermostat.
Anti-freeze function
- Turn the function selector knob to one of the 3 different heating positions available (Fig.
5).
- Turn the thermostat knob to the anti-freeze position
(Fig. 5).
- On models fitted with electronic timer, slide the starter indicator (fig.5) to position “I”; the
indicator lamp will come on.
When the fan heater has been set in this way it will automatically come on whenever the
temperature in the room falls close to zero degrees and the room will thus remain at a
temperature of a few degrees above zero.
Summer use
- Turn the function selector knob to the “fans only” position (Fig. 5).
- Turn the thermostat knob to the “summer use" position
- On models fitted with electronic timer, slide the starter indicator (fig.5) to position “I”; the
indicator lamp will come on.
The fans only will be switched on when the fan heater has been set in this way.
(Fig. 5).
Switching off the heater
Turn the function selector knob back to its “O” position (Fig. 5) to switch off the fan heater. On
models with the electronic timer, you must also press the start pushbutton (Fig. 5) until moving
the display line to the “O” position (Fig. 6).
ELECTRONIC TIMER (not on all models)
Setting the time and day of the week
Set the timer to the correct time, proceeding as follows:
- Press the pushbutton and pushbutton (Fig. 5) simultaneously until the display
shows the hours for the correct time, then release both pushbuttons.
PROGRAM START
PROGRAM END
PROGRAM NUMBER
PILOT LIGHT
fig. 6
5