Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP
and DLP logo are trademarks of T
Windows are either trademarks or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Your projector comes with all the items shown below. Ensure that you have all
the items, and contact Dell if anything is missing.
Projector Box Contents
Package Contents
Power cable1.8 m HDMI cable (2.0 spec)
Remote control (CR2032 x 2pcs)
4About Your Dell Projector
User's Guide and Documentation
Projector Top and Bottom View
4
3
1
5
2
Top ViewBottom View
1IR receivers
2Status indicators
3Power button
4Lens
56W (x 2) speakers
6Mounting holes for wall mount
7Tilt adjustment wheel
NOTE: Wall mount screw hole M4 x 9 mm depth.
200.00
7
160.00
140.0090.99
80.00
6
About Your Dell Projector5
Projector Connections
1 234
5
6
13111278910
1 Mini USB (mini type B) connector
8 SPDIF connector
for firmware upgrade
2 RJ45 connector9 USB Type A Power (5V/1.8A)
connector
3 HDMI 1 (2.0) connector10 USB Type A Power (5V/1.8A)
connector
4 HDMI 2 (1.4) connector11 Power cord connector
5 HDMI 3 (1.4) connector12 RS232 connector
6 USB (Type A) 3.0 connector for
13 Kensington cable slot
USB media playback and
optional wireless dongle
7 Audio output connector
CAUTION: Before you begin any of the procedures in this
section, follow the Safety Instructions as described on page 7.
6About Your Dell Projector
CAUTION: Safety Instructions
1
Do not use the projector near appliances that generate a lot of heat.
2
Do not use the projector in areas where there is an excessive amount of
dust. The dust may cause the system to fail and the projector will
automatically shutdown.
3
Ensure that the projector is mounted in a well-ventilated area.
4
Do not block the ventilation slots and openings on the projector.
5
Ensure the projector operates between ambient temperatures 5°C to 40°C
(41°F to 104°F).
6
Do not try to touch the ventilation outlet as it can become very hot after the
projector has been turned on or immediately after it is turned off.
7
Do not look into the lens while the projector is on as it may cause injury to
your eyes.
8
Do not place any objects near or in front of the projector or cover its lens
while the projector is on as the heat may cause the object to melt or burn.
9
Do not use alcohol to wipe the lens.
NOTE:
•
Do not attempt to ceiling mount the projector by yourself. It should be
installed by a qualified technician.
•
Recommended Projector Wall Mount Kit. For more information, see the
Dell Support website at
•
For more information, see the Safety Information that shipped with your
dell.com/support
.
projector.
•
The S718QL projector can only be used indoors.
About Your Dell Projector7
WARNING: Laser Safety Notice
This product is classified as CLASS 1 LASER PRODUCT - RISK
GROUP 2 according to IEC 60825-1 : 2014 complies with FDA
regulations 21 CFR 1040.10 and 1040.11 as a Risk Group 2 , LIP (
Laser Illuminated Projector) as defined in IEC 62471:2006 except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
•
Failure to comply with the following could result in death or serious
injury.
•
This projector has a built-in Class 4 laser module. Never attempt to
disassemble or modify the projector.
•
Any operation or adjustment not specifically instructed in the User
manual creates the risk of hazardous laser radiation exposure.
•
Do not open or disassemble the projector as this may cause damage or
exposure to laser radiation.
•
Do not stare into beam when the projector is on. The bright light may
result in permanent eye damage.
•
When turning on the projector, make sure no one within projection range
is looking into the lens.
•
Follow the control, adjustment, or operation procedures to avoid damage
or injury from exposure of laser radiation.
•
The instructions for the assembly, operation, and maintenance include
clear warnings concerning precautions to avoid possible exposure to
hazardous laser radiation.
8About Your Dell Projector
Remote Control
Video
Mode
Freeze
Blank
1
2
3
4
5
6
7
8
11
12
15
14
13
10
9
1Power Turns the projector on or off.
2Back Returns to the previous screen.
3Up Press to navigate through the On-Screen
4Right Press to navigate through the On-Screen
Display (OSD) Menu items.
Display (OSD) Menu items.
5Down Press to navigate through the On-Screen
Display (OSD) Menu items.
6Volume down Press to decrease the volume.
About Your Dell Projector9
7Volume up Press to increase the volume.
8FreezePress to pause the screen image, then press
"Freeze" again to resume normal projection.
9Video inPress to switch between sources: HDMI 1,
HDMI 2, HDMI 3, Wireless/LAN Display, and
USB Viewer.
10Video modeThe projector has preset configurations that
are optimized for displaying data (presentation
slides) or video (movies, games, etc.).
Press the Video Mode button to toggle
between Presentation mode, Bright mode,
Movie mode, sRGB, or Custom mode.
Pressing the Video Mode button once will
show the current display mode. Pressing the
Video Mode button again will switch between
modes.
11Menu Press to activate the OSD.
12Enter Press to confirm the selection.
13Left Press to navigate through the On-Screen
Display (OSD) Menu items.
14Mute Press to mute or un-mute the projector
speaker.
15Blank Press to toggle between white/blank/resume
Blank
the image.
10About Your Dell Projector
Remote Control Operating Range
Video
Mode
Freeze
Blank
Video
Mode
Freeze
Blank
Operating range
Angle±30°
Distance7 m/22.97 feet
$QJOH
'LVWDQFH
$QJOH
'LVWDQFH
NOTE: Actual operating range may slightly differ from the diagram.
Weak batteries will also prevent the remote control from properly
operating the projector.
About Your Dell Projector11
Adjusting Projector Image
3.6°
1
1
22
2
Adjusting Projected Zoom
Raising the Projector Height
1
Raise the projector to the desired display angle, and use the rear tilt
adjustment wheel to fine-tune the display angle.
Lowering the Projector Height
1
Lower the projector, and use the front tilt adjustment wheel to fine-tune the
display angle.
Adjust the focus until the image is clear. The projector focuses at distances
ranging between 0.32 ft to 0.74 ft (10 cm to 22.5 cm).
Adjusting Projector Image13
Adjusting Projector Position
Case ACase B
Wall Mount Projection
Table Top Projection
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
•
When positioning the projector to the screen, it must be at least 3.9 inches
(10 cm) from the projection screen.
•
Position the projector to the required distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the video
format determine the size of the projected image.
•
Lens throw ratio: 0.189
You can set up or install the S718QL in the following ways:
14Adjusting Projector Image
Case C
Upward Projection
Case D
Portrait Right Projection
Case E
Portrait Left Projection
Adjusting Projector Image15
Adjusting Image Corners
Use 4 corner adjustment feature to get perfect, rectangular images.
1
Advanced Settings > Keystone Settings > Four Corner
2
At four corner screen, use
to confirm.
3
Use
, ,
and to adjust the image shape as necessary.
, ,
and to select one corner and press
4
When you are finished, press "Menu" button to exit.
NOTE: The function is unavailable when H./V. Keystone is adjusted.
16Adjusting Projector Image
Adjusting Image Size
Projector to screen distance (Horizontal)
130" (330.2 cm)
120" (304.8 cm)
110" (279.4 cm)
0.74' (22.5 cm)
0.60' (18.4 cm)
0.47' (14.2 cm)
Adjusting Projector Image17
100" (254.0 cm)
0.32' (10.0 cm)
Adjusting Image Shape
S3
L2
(Offset)
L1
Projection
Distance (L1)
inchcminchcminchcminchcminchcm
3.910.0100254.087.1221.249.0124.57.318.6
5.614.2110279.495.8243.353.9137.08.220.9
7.218.4120304.8104.5265.458.8149.49.123.1
8.922.5130330.2113.2287.563.7161.910.025.4
* This graph is for user reference only.
* Offset Ratio: 118%
Diagonal (S1)Width (S2)Height (S3)
Image sizeDistance from top
of image to top of
projector (L2)
18Adjusting Projector Image
Using Your Projector
3
Using Network Display
Configure Your Projector for Network Display
Connect Projector to the Network
1
Connect the power cable and turn on the projector by pressing the power
button.
2
Press the
Menu
button on your projector control panel or remote control.
NOTE: Use , ,
select.
and
buttons to navigate and to
Using Your Projector19
3
Ensure DHCP option is
4
Access the
The
Network Guide Screen
Input Source
Off
from LAN settings of Advanced Settings menu.
menu, select
Network
source.
shown below appears:
20Using Your Projector
Connect Projector Directly to the Computer
A.Cable Connections
5
Connect the LAN cable to the projector and the computer.
B.Switch Source
6
Connect the LAN cable to the projector and the computer via the switch
source.
7
DHCP of LAN Settings switches to On.
NOTE: If the DHCP setting is set to On, the IP sharing device will
automatically assign a set of IP Address, Subnet Mask, and Gateway.
Using Your Projector21
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.