How it Works
Dell
Loading...
P36G
Owner's Manual
61 pgs6.43 Mb0

Dell Latitude 6430u, P36G Owner's Manual

Dell Latitude 6430u Owner's Manual
Regulatory Model: P36G Regulatory Type: P36G001
Contents
Notes, Cautions, and Warnings.............................................................................................. 0
Before Working Inside Your Computer.....................................................................................................................5
Turning Off Your Computer.......................................................................................................................................6
After Working Inside Your Computer........................................................................................................................6
2 Removing and Installing Components.....................................................................................7
Recommended Tools................................................................................................................................................7
System Overview......................................................................................................................................................7
Removing the Secure Digital (SD) Card....................................................................................................................9
Installing the Secure Digital (SD) Card.....................................................................................................................9
Removing the Battery.............................................................................................................................................10
Installing the Battery..............................................................................................................................................10
Removing the Base Cover.......................................................................................................................................10
Installing the Base Cover........................................................................................................................................11
Removing the mSATA SSD Card.............................................................................................................................11
Installing the mSATA SSD Card..............................................................................................................................12
Removing the Memory............................................................................................................................................12
Installing the Memory.............................................................................................................................................12
Removing the Wireless Local Area Network (WLAN) Card...................................................................................12
Installing the WLAN Card.......................................................................................................................................13
Removing the Wireless Wide Area network (WWAN) Card..................................................................................13
Installing the WWAN Card.....................................................................................................................................13
Removing the TAA Board.......................................................................................................................................14
Installing the TAA Board.........................................................................................................................................14
Removing the System Fan.......................................................................................................................................14
Installing the System Fan........................................................................................................................................15
Removing the Keyboard..........................................................................................................................................15
Installing the Keyboard...........................................................................................................................................17
Removing the Palmrest Assembly..........................................................................................................................17
Installing the Palmrest Assembly...........................................................................................................................19
Removing the Power-Switch Board.......................................................................................................................20
Installing the Power-Switch Board........................................................................................................................20
Removing the Fingerprint-Scanner Board..............................................................................................................20
Installing the Fingerprint-Scanner Board...............................................................................................................21
Removing the Display Bezel...................................................................................................................................21
Installing the Display Bezel.....................................................................................................................................22
Removing the Display Panel...................................................................................................................................22
Installing the Display Panel....................................................................................................................................23
Removing the Power LED Board.............................................................................................................................24
Installing the Power LED Board..............................................................................................................................24
Removing the Camera.............................................................................................................................................24
Installing the Camera..............................................................................................................................................25
Removing the Speakers..........................................................................................................................................25
Installing the Speakers...........................................................................................................................................26
Removing the Coin-Cell Battery..............................................................................................................................26
Installing the Coin-Cell Battery...............................................................................................................................27
Removing the Smart-Card Board............................................................................................................................27
Installing the Smart-Card Board.............................................................................................................................28
Removing the Smart-Card Cage.............................................................................................................................28
Installing the Smart-Card Cage..............................................................................................................................29
Removing the Hall Sensor.......................................................................................................................................29
Installing the Hall Sensor........................................................................................................................................30
Removing the Sniffer Board....................................................................................................................................30
Installing the Sniffer Board.....................................................................................................................................31
Removing the Display Assembly.............................................................................................................................31
Installing the Display Assembly..............................................................................................................................33
Removing the Power Connector.............................................................................................................................33
Installing the Power Connector..............................................................................................................................34
Removing the System Board...................................................................................................................................34
Installing the System Board....................................................................................................................................36
Removing the Thermal Module...............................................................................................................................36
Installing the Thermal Module................................................................................................................................37
3 System Setup.............................................................................................................................39
System Setup Overview..........................................................................................................................................39
Boot Sequence.......................................................................................................................................................39
Navigation Keys......................................................................................................................................................39
Updating the BIOS .................................................................................................................................................40
System Setup Option..............................................................................................................................................40
4 Troubleshooting.........................................................................................................................49
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...............................................................................49
Diagnostics.............................................................................................................................................................49
Beep Codes.............................................................................................................................................................50
LED Error Codes......................................................................................................................................................51
5 Specifications............................................................................................................................53
System Setup Option..............................................................................................................................................53
6 Contacting Dell..........................................................................................................................61
Contacting Dell.......................................................................................................................................................61
Working on Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning Off Your Computer).
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
3. Disconnect all network cables from the computer.
4. Disconnect your computer and all attached devices from their electrical outlets.
5. Press and hold the power button while the computer is unplugged to ground the system board.
6. Remove the cover.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.
5
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
1. Shut down the operating system:
– In Windows 8: If you using a touch-enabled device:
Swipe in from the right edge of the screen, opening the Charms menu and select Settings. Select the and then select Shut down
– In Windows 8: If using a mouse:
Point to upper-right corner of the screen and click Settings. Click on the and then select Shut down.
– In Windows 7:
Click Start , then click Shut Down.
– In Windows Vista:
Click Start , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down.
2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 6 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.
1. Replace the cover.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.
2. Connect any telephone or network cables to your computer.
3. Connect your computer and all attached devices to their electrical outlets.
4. Turn on your computer.
5. If required, verify that the computer works correctly by running the Dell Diagnostics.
6
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your computer.
Recommended Tools
The procedures in this document may require the following tools:
• Small flat-blade screwdriver
• Phillips screwdriver
• Small plastic scribe
System Overview
Figure 1. Back view
1. secure digital (SD) card
2. battery
3. battery release latch
4. base cover
7
Figure 2. Inside view — back
1. wireless local area network (WLAN) card
2. system fan
3. thermal module
4. memory
5. smart card cage
6. TAA board
7. mSATA SSD card
8. subscriber identification module (SIM) card slot
9. SD card slot
10. wireless wide area network (WWAN) card
8
Figure 3. Inside view — front
1. sniffer board
2. hall sensor
3. smart card board
4. system board
5. coin-cell battery
Removing the Secure Digital (SD) Card
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Press in on the SD card to release it from the computer.
3. Slide the SD card out of the computer.
Installing the Secure Digital (SD) Card
1. Push the SD card into the compartment until it clicks into place.
2. Follow the procedures in
After Working Inside Your Computer
.
9
Removing the Battery
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Slide the release latch to unlock the battery, and slide to remove the battery from the computer.
Installing the Battery
1. Slide the battery into its slot until it clicks into place.
2. Follow the procedures in
After Working Inside Your Computer.
Removing the Base Cover
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card
3. Remove the screws that secure the base cover to the computer, and slide the base cover and remove it.
10
Installing the Base Cover
1. Place the base cover to align with the screw holes on the computer.
2. Tighten the screws to secure the base cover to the computer.
3. Install:
a) SD card b) battery
4. Follow the procedures in
After Working Inside Your Computer
.
Removing the mSATA SSD Card
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Remove the screw that secures the mSATA SSD card and remove the mSATA SSD card from the computer.
11
Installing the mSATA SSD Card
1. Place the mSATA SSD card in its slot in the computer.
2. Tighten the screw to secure the mSATA SSD card to the computer.
3. Install:
a) base cover b) SD card c) battery
4. Follow the procedures in
After Working Inside Your Computer
.
Removing the Memory
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Pry the securing clips away from the memory module until it pops up. Remove the memory module from its connector on the system board.
Installing the Memory
1. Insert the memory module into the memory socket.
2. Press the memory module down until it clicks into place.
3. Install:
a) base cover b) SD card c) battery
4. Follow the procedures in
After Working Inside Your Computer
.
Removing the Wireless Local Area Network (WLAN) Card
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN card to the computer. Remove the WLAN card from the computer.
12
Installing the WLAN Card
1. Insert the WLAN card into its connector at a 45–degree angle into its slot.
2. Press the WLAN card down and tighten the screw to secure the WLAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WLAN card.
4. Install:
a) base cover b) SD card c) battery
5. Follow the procedures in
After Working Inside Your Computer
.
Removing the Wireless Wide Area network (WWAN) Card
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Disconnect the antenna cables from the WWAN card.
4. Remove the screw that secures the WWAN card to the computer.
5. Disconnect the antenna cables from the WWAN card. Remove the screw that secures the WWAN card to the
computer and remove it.
Installing the WWAN Card
1. Place the WWAN card in its slot in the system board.
2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.
3. Connect the antenna cables to their respective connectors marked on the WWAN card.
4. Install:
a) base cover b) SD card
13
c) battery
5. Follow the procedures in
After Working Inside Your Computer
.
Removing the TAA Board
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Remove the screw that secures the TAA board to the computer. Remove the TAA board from its slot on the system board.
Installing the TAA Board
1. Place the TAA board in its slot on the system board.
2. Tighten the screw that secures the TAA board to the computer.
3. Install:
a) base cover b) SD card c) battery
4. Follow the procedures in
After Working Inside Your Computer
.
Removing the System Fan
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Disconnect the system fan cable. Remove the screws that secure the system fan to the computer, and remove the system fan from the computer.
14
Installing the System Fan
1. Place the system fan in its slot on the computer.
2. Tighten the screws that secure the system fan to the computer.
3. Connect the system fan cable.
4. Install:
a) base cover b) SD card c) battery
5. Follow the procedures in
After Working Inside Your Computer
.
Removing the Keyboard
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover
3. Disconnect the keyboard-backlight cable, trackstick cable, and keyboard cable.
15
4. Remove the screws that secure the keyboard to the computer.
5. Using a flat screwdriver, release the snaps.
16
6. Flip the computer and remove the keyboard from the computer.
Installing the Keyboard
1. Slide the keyboard into its compartment and ensure that it clicks into place.
2. Flip the computer and tighten the screws to secure the keyboard.
3. Connect the keyboard cable, keyboard-backlight cable and trackstick cable.
4. Install:
a) base cover b) SD card c) battery
5. Follow the procedures in
After Working Inside Your Computer
.
Removing the Palmrest Assembly
1. Follow the procedures in
Before Working Inside Your Computer
.
2. Remove:
a) battery b) SD card c) base cover d) keyboard
17
3. Disconnect the media-board cable, power-switch cable, touchpad cable, fingerprint-scanner cable and speaker cable.
4. Remove the screws that secure the palmrest assembly to the computer.
18
5. Flip the computer and remove the screws that secure the palmrest assembly to the base of the computer and flip
open the lower assembly.
6. Press against the sections to release the palmrest assembly and remove it from the computer.
Installing the Palmrest Assembly
1. Align the palmrest assembly to its original position in the computer until it snaps into place.
2. Tighten the screws to secure the palmrest assembly to the computer..
3. Flip the computer and tighten the screws to secure the palmrest assembly to the computer.
4. Tighten the screws to secure the palmrest assembly to the base of the computer.
5. Connect the following cable:
a) Speaker cable b) fingerprint-scanner cable c) touchpad cable d) power-switch cable
19
Loading...
+ 42 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use