Dell Inspiron 5401 Service manual

Inspiron 14 5401

Service Manual

Regulatory Model: P130G

Regulatory Type: P130G001

May 2020

Rev. A00

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

Contents

1 Working inside your computer.......................................................................................................	6
Before working inside your computer.................................................................................................................................	6
Safety instructions.................................................................................................................................................................	6
Electrostatic discharge—ESD protection..........................................................................................................................	7
ESD field service kit ..............................................................................................................................................................	7
Transporting sensitive components....................................................................................................................................	8
After working inside your computer....................................................................................................................................	8
2 Removing and installing components.............................................................................................	9
Recommended tools..............................................................................................................................................................	9
Screw list................................................................................................................................................................................	9
Major components of Inspiron 14 5401..............................................................................................................................	10
Base cover.............................................................................................................................................................................	12
Removing the base cover..............................................................................................................................................	12
Installing the base cover................................................................................................................................................	14
Battery...................................................................................................................................................................................	16
Removing the 4-cell battery.........................................................................................................................................	16
Installing the 4-cell battery............................................................................................................................................	17
Removing the 3-cell battery..........................................................................................................................................	17
Installing the 3-cell battery............................................................................................................................................	18
Memory module....................................................................................................................................................................	19
Removing the memory module.....................................................................................................................................	19
Installing the memory module......................................................................................................................................	20
Solid-state drive—M.2 slot one........................................................................................................................................	22
Removing the 2230 solid-state drive in M.2 slot one...............................................................................................	22
Installing the 2230 solid-state drive in M.2 slot one..................................................................................................	22
Removing the 2280 solid-state drive in M.2 slot one...............................................................................................	23
Installing the 2280 solid-state drive in M.2 slot one..................................................................................................	24
Replacing the SSD-1 support bracket.........................................................................................................................	25
Solid-state drive—M.2 slot two........................................................................................................................................	26
Removing the 2230 solid-state drive in M.2 slot two...............................................................................................	26
Installing the 2230 solid-state drive in M.2 slot two.................................................................................................	27
Removing the 2280 solid-state drive in M.2 slot two...............................................................................................	29
Installing the 2280 solid-state drive in M.2 slot two.................................................................................................	30
Replacing the SSD-2 support bracket.........................................................................................................................	31
WLAN card...........................................................................................................................................................................	32
Removing the WLAN card............................................................................................................................................	32
Installing the WLAN card..............................................................................................................................................	32
Fan.........................................................................................................................................................................................	34
Removing the fan..........................................................................................................................................................	34
Installing the system fan...............................................................................................................................................	35
Coin-cell battery..................................................................................................................................................................	36
Removing the coin-cell battery....................................................................................................................................	36
Installing the coin-cell battery......................................................................................................................................	36

Contents 3

Power-adapter port.............................................................................................................................................................	37
Removing the power-adapter port..............................................................................................................................	37
Installing the power-adapter port................................................................................................................................	38
Display assembly..................................................................................................................................................................	39
Removing the display assembly...................................................................................................................................	39
Installing the display assembly......................................................................................................................................	41
I/O board..............................................................................................................................................................................	43
Removing the I/O board...............................................................................................................................................	43
Installing the I/O board.................................................................................................................................................	44
Touchpad..............................................................................................................................................................................	44
Removing the touchpad...............................................................................................................................................	44
Installing the touchpad..................................................................................................................................................	45
Speakers...............................................................................................................................................................................	47
Removing the speakers (in 4-cell battery configuration).........................................................................................	47
Installing the speakers (in 4-cell battery configuration)...........................................................................................	48
Removing the speakers (in 3-cell battery configuration).........................................................................................	49
Installing the speakers (in 3-cell battery configuration)...........................................................................................	50
Heat sink................................................................................................................................................................................	51
Removing the heat sink.................................................................................................................................................	51
Installing the heat sink...................................................................................................................................................	52
Power button with optional fingerprint reader................................................................................................................	52
Removing the power button with optional fingerprint reader.................................................................................	53
Installing the power button with optional fingerprint reader....................................................................................	53
System board.......................................................................................................................................................................	54
Removing the system board........................................................................................................................................	54
Installing the system board...........................................................................................................................................	56
Palm-rest and keyboard assembly....................................................................................................................................	58
Removing the palm-rest and keyboard assembly......................................................................................................	58
Installing the palm-rest and keyboard assembly........................................................................................................	59
3 Drivers and downloads................................................................................................................	60
4 System setup.............................................................................................................................	61
Entering BIOS setup program.............................................................................................................................................	61
Navigation keys....................................................................................................................................................................	61
One time boot menu............................................................................................................................................................	61
System setup options.........................................................................................................................................................	62
Updating the BIOS in Windows ........................................................................................................................................	69
Updating BIOS on systems with BitLocker enabled..................................................................................................	70
Updating your system BIOS using a USB flash drive................................................................................................	70
Updating the Dell BIOS in Linux and Ubuntu environments...........................................................................................	71
Flashing the BIOS from the F12 One-Time boot menu...................................................................................................	71
System and setup password..............................................................................................................................................	74
Assigning a system setup password............................................................................................................................	74
Deleting or changing an existing system setup password........................................................................................	75
Clearing CMOS settings...............................................................................................................................................	75
Clearing BIOS (System Setup) and System passwords...........................................................................................	75
5 Troubleshooting.........................................................................................................................	76

4 Contents

SupportAssist diagnostics..................................................................................................................................................	76
Built-in self-test (BIST).......................................................................................................................................................	76
System board built-in self-test (M-BIST)...................................................................................................................	77
Display panel power rail built-in self-test (L-BIST)....................................................................................................	77
Display panel built-in self-test (LCD-BIST)................................................................................................................	78
Outcome.........................................................................................................................................................................	78
Recovering the operating system......................................................................................................................................	79
System diagnostic lights.....................................................................................................................................................	79
Enabling Intel Optane memory...........................................................................................................................................	80
Disabling Intel Optane memory..........................................................................................................................................	80
Flea power release...............................................................................................................................................................	81
WiFi power cycle..................................................................................................................................................................	81
6 Getting help and contacting Dell..................................................................................................	82

Contents 5

Working inside your computer

Before working inside your computer

About this task

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Steps

1.Save and close all open files and exit all open applications.

2.Shut down your computer. Click Start > Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down instructions.

3.Disconnect your computer and all attached devices from their electrical outlets.

4.Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

5.Remove any media card and optical disc from your computer, if applicable.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.

NOTE: Before working inside your computer, read the safety information that is shipped with your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.

NOTE: Disconnect your computer from all power sources before opening the computer cover or panels. After you finish working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and the contacts.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity which could harm internal components.

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When disconnecting cables, keep them evenly-aligned to avoid bending the connector pins. When connecting cables, ensure that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

6 Working inside your computer

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

•Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

•Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

•Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased sensitivity to ESD damage.

•Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

•When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body.

•Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: antistatic mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

•Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an antistatic mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESDsensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

•Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at least once per week.

•ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

•Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are insulators and often highly charged.

Working inside your computer

•Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically handling any hardware components

•ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

•Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

Lifting equipment

Adhere to the following guidelines when lifting heavy weight equipment:

CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.

1.Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.

2.Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.

3.Lift with your legs, not your back.

4.Keep the load close. The closer it is to your spine, the less force it exerts on your back.

5.Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting your body and back.

6.Follow the same techniques in reverse to set the load down.

After working inside your computer

About this task

CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.

Steps

1.Replace all screws and ensure that no stray screws remain inside your computer.

2.Connect any external devices, peripherals, or cables you removed before working on your computer.

3.Replace any media cards, discs, or any other parts that you removed before working on your computer.

4.Connect your computer and all attached devices to their electrical outlets.

5.Turn on your computer.

8 Working inside your computer

Removing and installing components

Recommended tools

The procedures in this document may require the following tools:

•Phillips screwdriver #1

•Phillips screwdriver #0

•Plastic scribe

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

Component	Secured to	Screw type	Quantity	Screw image


Base cover	Palm-rest and keyboard	M2 x 4	5
	assembly
					NOTE: Screw color


					may vary depending on
					the configuration
					ordered.

Battery	Palm-rest and keyboard	M2 x 3	5
	assembly
					NOTE: Screw color


					may vary depending on
					the configuration
					ordered.

Solid-state drive bracket	Palm-rest and keyboard	M2 x 3	1
	assembly

Solid-state drive	Palm-rest and keyboard	M2 x 3	1
	assembly

Fan	Palm-rest and keyboard	M2 x 2	2
	assembly

Wireless-card bracket	System board	M2 x 3	1

Touchpad	Palm-rest and keyboard	M2 x 2	2
	assembly

Removing and installing components

Table 1. Screw list(continued)

Component	Secured to	Screw type	Quantity	Screw image


Touchpad bracket	Palm-rest and keyboard	M1.6 x 2	3
	assembly

Power-button bracket	Palm-rest and keyboard	M2 x 2	1
	assembly

Power button with	Palm-rest and keyboard	M2 x 2.5	2
fingerprint reader	assembly
(optional)

Power-adapter port	Palm-rest and keyboard	M2 x 3	1
bracket	assembly

USB 3.1 Type-C port	System board	M2 x 3	2
bracket

Hinge brackets	Palm-rest and keyboard	M2.5 x 5	4
	assembly

I/O board	Palm-rest and keyboard	M2 x 3	1
	assembly

System board	Palm-rest and keyboard	M2 x 3	2
	assembly

Major components of Inspiron 14 5401

The following image shows the major components of Inspiron 14 5401.

10 Removing and installing components

1.Base cover

2.Battery

3.Power-adapter port

4.Heat sink

5.Memory module

6.Solid-state drive bracket

7.M.2 2230 solid-state drive in M.2 slot two

8.Speakers

9.System board

10.Touchpad

11.Palm-rest and keyboard assembly

12.Display assembly

13.Power button with fingerprint reader

14.Coin-cell battery

15.I/O board

16.Fan

17.Wireless card

18.M.2 2280 Solid-state drive in M.2 slot one

Removing and installing components

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in before working inside your computer.

About this task

The following images indicate the location of the base cover and provide a visual representation of the removal procedure.

12 Removing and installing components

Steps

1.Loosen the two captive screws that secure the base cover to the palm-rest and keyboard assembly.

2.Remove the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

Removing and installing components

3.Using a plastic scribe, pry the base cover beside the display hinges, and then continue to work on the sides to open the base cover.

4.Disconnect the battery cable from the system board.

NOTE: Disconnect the battery cable only when you are continuing to remove other components from your computer.

5. Press and hold the power button for five seconds to ground the computer and drain the flea power.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

14 Removing and installing components

Removing and installing components

Steps

1.Connect the battery cable to the system board, if applicable.

2.Place the base cover on top of the palm-rest and keyboard assembly.

3.Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly, and then snap the base cover into place.

4.Tighten the two captive screws that secure the base cover to the palm-rest and keyboard assembly.

5.Replace the five (M2x4) screws that secure the base cover to the palm-rest and keyboard assembly.

Next steps

1. Follow the procedure in after working inside your computer.

Battery

Removing the 4-cell battery

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

The following images indicate the location of the battery and provide a visual representation of the removal procedure.

Steps

1.Peel the tape and disconnect the battery cable, if applicable.

2.Remove the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3.Lift the battery, along with its cable off the palm-rest and keyboard assembly.

16 Removing and installing components

Installing the 4-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Steps

1.Place the battery on the palm-rest and keyboard assembly.

2.Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.

3.Replace the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4.Connect the battery cable to the system board and adhere the tape that secures the battery cable to the system board.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

Removing the 3-cell battery

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

Removing and installing components

About this task

The following images indicate the location of the battery and provide a visual representation of the removal procedure.

Steps

1.Peel the tape and disconnect the battery cable, if applicable.

2.Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3.Lift the battery, along with its cable off the palm-rest and keyboard assembly.

Installing the 3-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

18 Removing and installing components

Steps

1.Place the battery on the palm-rest and keyboard assembly.

2.Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.

3.Replace the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4.Connect the battery cable to the system board and adhere the tape that secures the battery cable to the system board.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

Memory module

Removing the memory module

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

The following images indicate the location of the memory module and provide a visual representation of the removal procedure.

Removing and installing components

Steps

1.Lift the mylar to uncover the memory module.

2.Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module popsup.

3.Remove the memory module from the memory-module slot.

Installing the memory module

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the memory module and provides a visual representation of the installation procedure.

20 Removing and installing components

Steps

1.Lift the mylar to find the memory-module slot.

2.Align the notch on the memory module with the tab on the memory-module slot.

3.Slide the memory module firmly into the slot at an angle.

4.Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

Removing and installing components

Solid-state drive—M.2 slot one

Removing the 2230 solid-state drive in M.2 slot one

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot one.

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive or a 2280 solidstate drive in M.2 slot one.

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot one and provides a visual representation of the removal procedure.

Steps

1.Remove the screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2.Slide and lift the solid-state drive off the SSD1 slot on the system board.

Installing the 2230 solid-state drive in M.2 slot one

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot one.

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive or a 2280 solidstate drive in M.2 slot one.

22 Removing and installing components

NOTE: Install the solid-state drive mounting bracket, if it is not installed.

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot one and provides a visual representation of the installation procedure.

Steps

1.Align the notches on the solid-state drive with the SSD1 slot on the system board.

2.Slide the solid-state drive into the SSD1 slot on the system board.

3.Replace the screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

Removing the 2280 solid-state drive in M.2 slot one

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

About this task

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot one.

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive or a 2280 solidstate drive in M.2 slot one.

The following image indicates the location of the 2280 solid-state drive/Intel Optane storage that is installed in M.2 slot one and provides a visual representation of the removal procedure.

Removing and installing components

Steps

1.Remove the screw (M2x3) that secures the solid-state drive/Intel Optane storage to the palm-rest and keyboard assembly.

2.Slide and lift the solid-state drive/Intel Optane storage off the SSD1 slot on the system board.

Installing the 2280 solid-state drive in M.2 slot one

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot one.

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive or a 2280 solidstate drive in M.2 slot one.

NOTE: Install the solid-state drive mounting bracket, if it is not installed.

The following image indicates the location of the 2280 solid-state drive/Intel Optane storage that is installed in M.2 slot one and provides a visual representation of the installation procedure.

24 Removing and installing components

Steps

1.Align the notches on the solid-state drive/Intel Optane storage with the SSD1 slot on the system board.

2.Slide the solid-state drive/Intel Optane storage into the SSD1 slot on the system board.

3.Replace the screw (M2x3) that secures the solid-state drive/Intel Optane storage to the palm-rest and keyboard assembly.

Next steps

1.Install the base cover.

2.Follow the procedure in after working inside your computer.

Replacing the SSD-1 support bracket

Prerequisites

1.Follow the procedure in before working inside your computer.

2.Remove the base cover.

3.Remove the solid-state drive in M.2 slot one.

About this task

The figure provides a visual representation of the replace procedure.

Removing and installing components

+ 57 hidden pages