A.E.B. INDUSTRIALE s.r.l.
Via Brodolini, 8 - 40056 Crespellano (Bo) - ITALIA
Tel. + 39 051 969870 - Fax. + 39 051 969725
Internet: www.dbtechnologies.com
E-mail: info@dbtechnologies-aeb.com
MANUALE D’USO
USER MANUAL
BEDIENUNGSANLEITUNG
CARACTERISTIQUES TECHNIQUES
Made in Italy
COD. 420120167
digital power
RR
OPERAOPERA
DD
PROFESSIONAL ACTIVE SPEAKER
OPERAOPERA
DD
user manualuser manual
EnglishEnglishEnglish
13
EnglishEnglishEnglish
user manualuser manual
14
Object and Liquid Entry
The apparatus must be placed in inappropriate position. Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through cooling grid with consequent electrical
danger.
Ventilation
The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not block or cover any openings of the grid ventilation or heatsink. Install the apparatus
at a distance that ensures a good ventilation between devices.
Heat
Do not install the appliance near any source of heat.
Accessories and installation
For a safe installation, do not make any holes in the external chassis for the application of additional
brackets. In case of particular installations not described in this manual, contact technical service for
accessories specified by the manufacturer.
Follow the instructions
All operations and instructions in this user manual should be followed for a correct operation and
function of appliance. Pay attention in particular to:
- Never force the control elements (switches, controls, etc.).
- Do not force the amplifier to work in overload for extended periods of time.
Cleaning
Clean only with a dry cloth. Do not use solvents, alcohol, benzene or volatile substances for cleaning
the exterior parts.
CONNECTION
- For connecting the appliance, use only qualified and experienced personnel having sufficient
technical knowledge or specific instructions for making the connections correctly and thus
preventing electrical dangers.
- To prevent the risk of electrical shock, the appliance must only be supplied from the mains after
all connections have been completed.
- Before powering up the appliance, it is advisable to re-check all the connections.
- The entire sound system must be designed and installed in compliance with the current
standards and regulations regarding electrical systems.
SUGGESTIONS
CAUTION
To prevent inductive phenomena from giving rise to hum or disturbance which would jeopardize
efficient appliance operation, the cables that transmit microphone signals or line level signals (e.g. 0
dB/V) must be screened and should not be run in the vicinity of:
1) Equipment that produces strong magnetic fields (e.g. large power supply transformers)
2) Electrical energy conductors
3) Lines that supply speakers.
This device complies with European Directives 2006/95/EC and 2004/108/EC and is provided with
CE marking.
The respective declaration of conformity is available in AEB Industriale s.r.l.
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or
lower E2, E1) Electromagnetic environments.
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE THE COVER
(OR BACK). NO USER SERVICEABLE
PARTS INSIDE; REFER SERVICING TO
QUALIFIED PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRICAL SHOCK. DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous
voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock.
This symbol wherever it appears, alerts you to important operating and maintenance
instructions in the accompanying literature. Read the manual.
INSTALLATION AND OPERATING PRECAUTIONS
GENERAL
IMPORTANT NOTES
This manual is to be considered an integral part of the product, and must always accompany the
equipment when it changes ownership, as a reference for correct installation and operation as well as
for the safety regulations. The Manufacturing company will not assume any responsibility for incorrect
installation of the amplifier.
Read these instructions
All the safety and operation instructions should be read before the appliance is operated.
Heed all Warnings
All warnings on the appliance and in the operating instructions should be adhered to
Long period non use of equipment
If long term non use of appliance is expected, it would be better to unplug this apparatus from power
supply, put it into proper packaging and cover to avoid dust exposure.
Damage and repair
If apparatus has been damaged it is forbidden to repair it or to remove cover. Disconnect the unit from
the mains power and contact technical assistance for repair.
Keep these instructions
For a correct use of the appliance, the safety and operating instructions should be retained for future
reference.
Apparatus positioning
Make sure that the apparatus is positioned in a stable and secure way in order to avoid any dangerous
conditions for persons or objects.
Grounding protection
The apparatus is made in protection CLASS I to prevent the risk of electrical shock the appliance must
be connected to a mains socket outlet with a protective earthing connection. Before making the
electrical connection of the appliance, ensure that the electrical distribution network conforms to the
regulations regarding electrical equipment.
Power Source
The appliance should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance (see “Specifications”). In order not to jeopardize the safety
of the amplifier, it must only be connected to the mains using the power cable provided.
Power Cord Protection
To ensure a safe use of appliance, use only the power cord supplied with the equipment, taking care to
place it and protect it to avoid damage during use. If power cord becomes damaged contact technical
assistance and request replacement. Do not use cables other than supplied cables.
Water and Moisture
Do not install this apparatus near water (e.g. near washbasins, sinks, showers, bathtubs, swimming
pool, wet floors or anything in the presence of water and liquids in general).
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
user manualuser manual
EnglishEnglishEnglish
15
EnglishEnglishEnglish
user manualuser manual
16
DESCRIPTION
®
The models of the “OPERA D” series use cutting edge digital amplifiers of the DIGIPRO
series, providing three different powers - 200W, 400W, and 600W - to meet the
requirements of any kind of application.
These highly efficient amplifiers provide high power with limited weight and dimension.
Thanks to the low power dissipated, the cooling of the amplifier module does not require a
fan.
The digital preamplifier with DSP (Digital Signal Processing) controls the audio crossover
of the acoustic components, the frequency response, the limiter, and the phase
alignment. A selector enables to select one of two different equalizations - “FLAT” or
“PROCESSED“ - to provide high versatility for the different applications.
®
The amplifiers DIGIPRO 400W e 600W use power supplies featuring SMPS (SwitchedMode Power Supplies) technology.
This technology increases power supply efficiency and minimizes its weight.
The correct operation is signalled by the lighting of a blue indicator, located on the front
panel of the speaker. The indicator can be disabled following a specific procedure
described in paragraph “Front LED” (Page 20).
OPERA 208D
The 2-way bi-amplified speaker is equipped with 8”
woofer (1,5” voice coil) and 1” Neodymium driver (1”
voice coil) loaded with 80°/65°x60° asymmetric horn.
The speaker is in plastic material, provided with
recessed top handle, easing its transport.
The OPERA 208D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 150W
RMS for the bass section and 50W RMS for the high
frequency section.
In the bottom of the box there is a standard pole mount
cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
OPERA
D
II
TECHNOLOGIES
d
B
HANDLE
43° PLANE
43° PLANE
Æ 36mm PEDESTAL/BRACKET
HOUSING
AMPLIFIER
REFLEX HOLES
WOOFER
DRIVER
INDICATOR
LIGHT
REFLEX HOLES
E
A
P
O
R
E
A
P
O
R
D
D
B
B
d
d
S
C
T
E
H
G
L
E
O
N
O
I
S
C
T
E
H
G
L
E
O
N
O
I
BB
dd
S
C
T
E
H
G
L
E
O
N
O
I
S
C
T
E
H
G
L
E
O
N
O
I
dd
BB
I
S
E
C
T
EH
G
L
O
N
O
I
S
E
C
T
EH
G
L
O
N
O
OPERA 210D
The 2-way bi-amplified speaker is equipped with 10”
woofer (1,5” voice coil) and 1” Neodymium driver (1”
voice coil) loaded with 80°/65°x60°asymmetric horn.
The speaker is plastic material and is provided with
top handle, rubber coated , easing its transport
OPERA 410D
The 2-way bi-amplified speaker is equipped with 10”
woofer (2” voice coil) and 1” compression driver (1.3”
voice coil) loaded with 80°/65°x60° asymmetric horn.
The speaker is plastic material and is provided with
top handle, rubber coated , easing its transport
The OPERA 210D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 150W
RMS for the bass section and 50W RMS for the high
frequency section.
In the bottom of the box there is a standard pole mount
cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
The OPERA 410D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 300W
RMS for the bass section and 100W RMS for the high
frequency section.
In the bottom of the box there is a standard pole mount
cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
OPERAOPERA
DD
BB
dd
H
N
G
I
T
E
C
O
O
L
E
S
H
N
G
I
T
E
C
O
O
L
E
S
B
B
d
d
H
N
G
I
T
E
C
O
O
L
E
S
H
N
G
I
T
E
C
O
O
L
E
S
d
d
B
B
E
L
S
EH
N
O
G
I
T
O
C
E
L
S
EH
N
O
G
I
T
O
C
HANDLE
43° PLANE
AMPLIFIER
Æ 36mm PEDESTAL/BRACKET
HOUSING
43° PLANE
OPERA
D
II
TECHNOLOGIES
d
B
REFLEX HOLES
WOOFER
DRIVER
INDICATOR
LIGHT
REFLEX HOLES
HANDLE
43° PLANE
43° PLANE
TECHNOLOGIES
d
B
OPERA
D
II
Æ 36mm PEDESTAL/BRACKET
HOUSING
REFLEX HOLES
WOOFER
DRIVER
INDICATOR
LIGHT
REFLEX HOLES
OPERA 402D
The 2-way bi-amplified speaker is equipped with 12”
woofer (2” voice coil) and 1” compression driver (1.5”
voice coil) loaded with 80°/65°x60°asymmetric horn.
The speaker is plastic material and is provided with
top handle and two rubber coated side handles,
easing its transport.
OPERA 405D
The 2-way bi-amplified speaker is equipped with 15”
woofer (2” voice coil) and 1” compression driver (1.5”
voice coil) loaded with 80°/65°x60°asymmetric horn.
The speaker is plastic material and is provided with
top handle and two rubber coated side handles,
easing its transport.
The OPERA 402D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 300W
RMS for the bass section and 100W RMS for the high
frequency section.
In the bottom of the box there is a standard pole
mount cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
The OPERA 405D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 300W
RMS for the bass section and 100W RMS for the high
frequency section.
In the bottom of the box there is a standard pole
mount cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
HANDLEHANDLE
AMPLIFIER
OPE
RAOPE
RA
D D
BB
dd
E
C O
G
I
TEH
N
O
L S
E
C O
G
I
TEH
N
O
L S
BB
dd
E
C O
G
I
TEH
N
O
L S
E
C O
G
I
TEH
N
O
L S
dd
BB
T
C
H
N
E
OL
O
G
IS
E
T
C
H
N
E
OL
O
G
IS
E
user manualuser manual
EnglishEnglishEnglish
17
OPERA 602D
The 2-way bi-amplified speaker is equipped with 12”
Neodimio woofer (3” voice coil) and 1” compression
driver (1.75” voice coil) loaded with 80°/65°x60°
asymmetric horn.
The speaker is plastic material and is provided with
top handle and two rubber coated side handles,
easing its transport.
OPERA 605D
The 2-way bi-amplified speaker is equipped with 15”
Neodimio woofer (3” voice coil) and 1” compression
driver (1.75” voice coil) loaded with
80°/65°x60°asymmetric horn.
The speaker is plastic material and is provided with
top handle and two rubber coated side handles,
easing its transport.
The OPERA 602D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 400W
RMS for the bass section and 200W RMS for the high
frequency section.
In the bottom of the box there is a standard pole
mount cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
The OPERA 605D bi-amped active speaker is
®
equipped with a DIGIPRO amplifier delivering 400W
RMS for the bass section and 200W RMS for the high
frequency section.
In the bottom of the box there is a standard pole
mount cup (D36mm).
The speaker has been designed to be used also as
stage monitor (43° angle).
OER
P A
OER
P A
DD
BB
dd
C O
G
I
E
TE
H
N
O
L S
C O
G
I
E
TE
H
N
O
L S
BB
dd
C O
G
I
E
TE
H
N
O
L S
C O
G
I
E
TE
H
N
O
L S
dd
BB
TH
C
N
O
L
E
S
O
G
I
E
TH
C
N
O
L
E
S
O
G
I
E
EnglishEnglishEnglish
user manualuser manual
18
HANDLE
43° PLANE
43° PLANE
TECHNOLOGIES
d
B
OPERA
D
II
Æ 36mm PEDESTAL/BRACKET
HOUSING
REFLEX HOLES
WOOFER
DRIVER
INDICATOR
LIGHT
REFLEX HOLES
HANDLEHANDLE
AMPLIFIER
user manualuser manual
EnglishEnglishEnglish
19
EnglishEnglishEnglish
user manualuser manual
20
COMMANDS AND FUNCTIONS
AMPLIFIER PANEL
1) “Balenced Input” - “Link” - “Input Link” CONNECTORS
These balanced inputs can be used to connect balanced or unbalanced
microphones or audio sources at line level (0dB) (eg. preamplifier, mixer, recorder,
CD player, musical instrument, ...).
The balanced connector is connected in parallel and can be used to send the audio
signal to other amplified speakers, recorders or supplementary amplifiers.
2) “Limiter” INDICATOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
3) “Signal” INDICATOR LIGHT
This indicator shows green to indicate the presence of the audio signal (at a level of 20dB).
4) “Ready” INDICATOR LIGHT
This indicator shows green to indicate that the main power voltage is correct.
The LED shows green normal operating conditions
5) “Sensitivity” INPUT SENSITIVITY CONTROL
This control adjusts the sensitivity of the signal amplifier input.
This control does not affect the “Link” - “Input - Link” output level
6) MODE SWITCH
This two-way switch allows to choose between two different system presets.
The “Flat” position allows linear response of the speaker, which is mainly suitable for
the “live” application.
The “Processed” position emphasizes the low frequency and regulates the mid
frequency. It is suitable for music play back
7) “Input Sens” SWITCH
Position the switch in LINE to use a line level source (0 dB) or MIC to use a
microphone.
8) POWER CABLE SOCKET “MAINS”
Used for connecting the power cable supplied.
9) FUSE CARRIER “FUSE”
Mains fuse housing.
10) POWER SWITCH “POWER”
This switch can be used to switch the diffuser on and off.
1) INDICATOR LIGHT
The blue indicator light indicates speaker status
SPEAKER FRONT
CHARACTERISTICS AND PROTECTION
The speakers’s components in the box are protected by 1.2mm metal steel grille
and by 1.5mm metal steel grille covered by foam on
backside.
Front Grille
(8”
version) (10”,12” and 15” versions)
Cooling
Thermal control is provided by the internal microprocessor which, by means of two
sensors, controls the temperature of the amplifier and of the power supply, avoiding
overheating by limiting the overall volume.
In case of overheating (> 80 degrees) the volume decreases proportionally to the
temperature increase, making the change unnoticeable.
The correct volume and all the functions are automatically restored when standard
operating temperatures are reached.
Front LED
On the front of the speaker a blue LED indicates the state of the speaker.
During normal operation the speaker front LED can be disabled if necessary (theatre,
cinema installations)
To change the state of the front LED, press and release for several times (6 times) the
MODE switch during switch on, when all the LEDs ( Limiter , Signal and Ready ) on the
amplifier module are off.
To restore front LED operation, repeat the operation.
The diagnostics of the speaker provided by this LED, is still active even if the LED is
disabled.
Switch on
The amplifiers are equipped with a microprocessor to control the DSP and the amplifier.
The correct switch on of the amplifier is ensured by an initialization procedure; during this
test stage, the blue front LED flashes twice and the LEDs ( Limiter , Signal and Ready ),
located on the amplifier module, remain off for approx. 2 sec.
At the end of the switch on procedure, the front LED lights up (if enabled) and on the
amplifier module the Ready green LED only remains steadily on.
In case of severe failure of the speaker, the LED on the front panel flashes several times
and on the amplifier module, the Limiter red LED flashes.
The speaker switches to “mute”.
Failure indications and safeties
The microprocessor is able to signal three different kinds of failure by flashing the “Limter”
red LED on the amplifier panel before the lighting up of the “Ready” green LED. The three
types of failure are:
1) WARNING: a non severe error or auto-ripristinate malfunction is detected and the
performance of the speaker is not limited
2) LIMITATION: an error is detected and the performance of the speaker is limited (the
sound level is reduced by 3dB).
This does not affect the operation of the speaker since it continues to operate.
However, it is necessary to call the service centre to solve the issue.
3) FAILURE: a severe malfunction is detected. The speaker switches to “mute”.
Flashing Indication
1 or 2 Warning
3 or 4 Limitation
from 5 to 8 Failure
In case of failure, the “Ready” green LED remains off.
“”“” “”
“”“” “”
“”
“”
user manualuser manual
EnglishEnglishEnglish
21
EnglishEnglishEnglish
user manualuser manual
22
Perform the checks listed below:
- Check if the speaker is properly connected to the power supply.
- Make sure that the power supply is of correct voltage.
- Check that the amplifier is not overheated.
- Disconnect the speaker from the mains power supply, wait for a few minutes and
connect it again.
If after these tests the red “LIMITER” LED is still on, please contact an authorised service
centre.
LOUDSPEAKER INSTALLATION
WARNING
Make sure that the loudspeaker is securely installed in a stable position to avoid any
injuries or damages to persons or property.
For safety reasons do not place one loudspeaker on top of another without proper
fastening systems. Before hanging the loudspeaker check all the components for
damages, deformations, missing or damaged parts that may compromise safety during
installation.
If you use the loudspeakers outdoors avoid places that are exposed to bad weather.
The loudspeaker has the following mounting options:
- bookshelf (Fig. 1)
- floor (monitor) (Fig.2)
- on speaker stands (Fig.3)
- suspended with brackets supplied by the manufacturer (Fig.4)
WARNING
Never use the handles to hang the speaker!
R
OPEAR
OPEA
DD
BB
dd
HL
O
I
C
N
OG
E
E
T
S
HL
O
I
C
N
OG
E
E
T
S
B
B
d
d
HL
O
I
C
N
OG
E
E
T
S
HL
O
I
C
N
OG
E
E
T
S
d
d
B
B
H
OI
N E
T
O
L
G
EC
S
H
OI
N E
T
O
L
G
EC
S
OPER
A
OPER
A
D
D
B
B
d
d
T
O
O
I
S
C
E
H
L
E
N
G
T
O
O
I
S
C
E
H
L
E
N
G
B
B
d
d
T
O
O
I
S
C
E
H
L
E
N
G
T
O
O
I
S
C
E
H
L
E
N
G
d
d
B
B
N
O
TO
EHI E
SCG
L
N
O
TO
EHI E
SCG
L
TECHNICAL SPECIFICATIONS
OPERA 208 D OPERA 210D OPERA 410 D
Amp and processor
Power supply: Analog Analog SMPS
HF amp: Class-D 50 W/RMS Class-D 50 W/RMS Class-D 100 W/RMS
Bass amp: Class-D 150 W/RMS Class-D 150 W/RMS Class-D 300 W/RMS
Cooling: Convection, fan-free Convection, fan-free Convection, fan-free
System presets: Flat, Processed Flat, Processed Flat, Processed
Limiter: Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters
Pre-Amp: 24bit 48KHz DSP 24bit 48KHz DSP 24bit 48KHz DSP
X-over frequency: 2050 Hz, 24 dB/oct. 2050 Hz, 24 dB/ oct. 1940 Hz, 24 dB/ oct
Audio Data
Frequency response -10 dB: 67 Hz - 20 kHz 62 Hz - 20 kHz 61 Hz - 20 kHz
Frequency response +-3 dB: 78 Hz - 19 kHz 71 Hz - 19 kHz 70 Hz - 19 kHz
Max SPL: 121 dB 122 dB 127 dB
Bass/midrange woofer: 1x8“ - 1,5“ voice coil 1x10“ - 1,5“ voice coil 1x10 - 2“ voice coil
High frequency driver: 1x1“ driver Neodymium 1x1“ driver Neodymium 1x1“ Compression driver 1,3” voice coil
Horn: 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn
Input section
Signal input/link: XLR fem. Balanced XLR fem. Balanced XLR fem. Balanced
XLR male balanced XLR male balanced XLR male balanced
6,3mm JACK balanced 6,3mm JACK balanced 6,3mm JACK balanced
Input sensitivity: -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line)
Mains: IEC, VDE IEC, VDE IEC, VDE
Hardware
Pole mount: 36 mm 36mm 36mm
Handles: one on top one on top (rubber) one on top (rubber)
Angles up: 43° for monitor 43° for monitor 43° for monitor
Grille: 1,2mmm Metal with foam 1,5mmm Metal with foam 1,5mmm Metal with foam
Dimensions (W x H x D): 300 x 484 x 284 mm 343 x 553 x 304 mm 343 x 553 x 304 mm
Weight: 8,4 kg 9,8 kg 10,6 kg
Optional accessories: gig bag, mounting bracket gig bag, mounting bracket gig bag, mounting bracket
user manualuser manual
EnglishEnglishEnglish
23
EnglishEnglishEnglish
user manualuser manual
24
TECHNICAL SPECIFICATION
OPERA 402 D OPERA 405 D
Amp and processor
Power supply: SMPS SMPS
HF amp: Class-D 100 W/RMS Class-D 100 W/RMS
Bass amp: Class-D 300 W/RMS Class-D 300 W/RMS
Cooling: Convection, fan-free Convection, fan-free
System presets: Flat, Processed Flat, Processed
Limiter: Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters
Pre-Amp: 24bit 48KHz DSP 24bit 48KHz DSP
X-over frequency: 1870Hz, 24 dB/oct. 1850 Hz, 24 dB/ oct.
Audio Data
Frequency response -10 dB: 59 Hz - 20 kHz 49 Hz - 20 kHz
Frequency response +-3 dB: 70 Hz - 19 kHz 58 Hz - 19 kHz
Max SPL: 128 dB 129 dB
Bass/midrange woofer: 1x12“ - 2“ voice coil 1x15“ - 2“ voice coil
High frequency driver: 1x1“ compression driver - 1,5” voice coil 1x1“ compression driver - 1,5” voice coil
Horn: 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn
Input section
Signal input/link: XLR fem. Balanced XLR fem. Balanced
XLR male balanced XLR male balanced
6,3mm JACK balanced 6,3mm JACK balanced
Input sensitivity: -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line)
Mains: IEC, VDE IEC, VDE
Hardware
Pole mount: 36 mm 36mm
Handles: two on side (with rubber) two on side (with rubber)
One on top (with rubber) one on top (with rubber)
Angles up: 43° for monitor 43° for monitor
Grille: 1,5mmm Metallica with foam 1,5mmm Metallica with foam
Dimensions (W x H x D): 432 x 655 x 353mm 432 x 655 x 353mm
Weight: 14,1 kg 14,5 kg
Optional accessories: gig bag, mounting bracket gig bag, mounting bracket
TECHNICAL SPECIFICATION
OPERA 602 D OPERA 605 D
Amp and processor
Power supply: SMPS SMPS
HF amp: Class-D 200 W/RMS Class-D 200 W/RMS
Bass amp: Class-D 400 W/RMS Class-D 400 W/RMS
Cooling: Convection, fan-free Convection, fan-free
System presets: Flat, Processed Flat, Processed
Limiter: Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters
Pre-Amp: 24bit 48KHz DSP 24bit 48KHz DSP
X-over frequency: 1690 Hz, 24 dB/oct. 1670 Hz, 24 dB/ oct.
Audio Data
Frequency response -10 dB: 58 Hz - 20 kHz 48 Hz - 20 kHz
Frequency response +-3 dB: 68 Hz - 19 kHz 59 Hz - 19 kHz
Max SPL: 129 dB 130 dB
Bass/midrange woofer: 1x12“ - 3“ voice coil Neodymium 1x15“ - 3“ voice coil Neodymium
High frequency driver: 1x1“ compression driver (RCF ND350) 1x1“ compression driver (RCF Nd350) Neodymium
1,75“ voice coil Neodymium 1,75“ voice coil Neodymium
Horn: 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn
Input section
Signal input/link: XLR fem. Balanced XLR fem. Balanced
XLR male balanced XLR male balanced
6,3mm JACK balanced 6,3mm JACK balanced
Input sensitivity: -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line)
Mains: IEC, VDE IEC, VDE
Hardware
Pole mount: 36 mm 36mm
Handles (rubber): two on side (with rubber) two on side (with rubber)
one on top (with rubber) one on top (with rubber)
Angles up: 43° for monitor 43° for monitor
Grille: 1,5mmm Metal with foam 1,5mmm Metal with foam
Dimensions (W x H x D): 432 x 655 x 353mm 432 x 655 x 353mm
Weight: 12,4 kg 12,9 kg
Optional accessories: gig bag, mounting bracket gig bag, mounting bracket
-3dB
0dB
+4dB
88
Balanced Input
Sensitivity
Line
Mic
Flat
Processed
Ready
Signal
Limiter
Input Sens
Link
Input-Link
digital power
DIGITAL ACTIVE SPEAKERDIGITAL ACTIVE SPEAKER
OPERA
DD
00
I
PUSHPUSH
220-240V~ 50-60Hz
110-120V~ 50-60Hz
FUSE MAINS
MODULE POWER
CONSUMPTION
POWER
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
Internal voltage setup
Made in Italy
-3dB
0dB
+4dB
88
Balanced Input
Sensitivity
Line
Mic
Flat
Processed
Ready
Signal
Limiter
Input Sens
Link
Input-Link
digital power
DIGITAL ACTIVE SPEAKERDIGITAL ACTIVE SPEAKER
OPERA
DD
PUSHPUSH
220-240V~ 50-60Hz
110-120V~ 50-60Hz
FUSE MAINS
MODULE POWER
CONSUMPTION
POWER
“CAUTION”
TO PREVENT ELECTRICAL SHOCK
DO NOT REMOVE COVER
“AVIS”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
Internal voltage setup
Made in Italy
00
I
OPERA 208D
OPERA 210D
OPERA 208D
OPERA 210D
50
49
OPERA 410D - OPERA 402D - OPERA 405D
OPERA 602D - OPERA 605D
OPERA 410D - OPERA 402D - OPERA 405D
OPERA 602D - OPERA 605D
1
2
3
4
5
7
6
8
9
10
1
2
3
4
5
7
6
8
9
10
52
51
DIMENSIONI / DIMENSIONS
ABMESSUNGEN / DIMENSIONS
655655
43°43°
DIMENSIONI / DIMENSIONS
ABMESSUNGEN / DIMENSIONS
OPERA 208DOPERA 208D
284284
484484
432432
304304
300300
43°43°
43°43°
343343
353353
E
A
P
O
R
E
A
P
O
R
D
D
B
B
d
d
S
C
T
E
H
G
L
E
O
N
O
I
S
C
T
E
H
G
L
E
O
N
O
I
BB
dd
S
C
T
E
H
G
L
E
O
N
O
I
S
C
T
E
H
G
L
E
O
N
O
I
dd
BB
I
S
E
C
T
EH
G
L
O
N
O
I
S
E
C
T
EH
G
L
O
N
O
OP
ERAOPERA
DD
BB
dd
T
E
C
H
N
OGI
L
E
SOT
E
C
H
N
OGI
L
E
SO
BB
dd
T
E
C
H
N
OGI
L
E
SOT
E
C
H
N
OGI
L
E
SO
dd
BB
E
OL
S
T
E
HN
OG
I
C
E
OL
S
T
E
HN
OG
I
C
OPERAOPERA
DD
BB
dd
E
C
OG
I
T
E
H
N
O
L
S
E
C
OG
I
T
E
H
N
O
L
S
B
B
d
d
E
C
OG
I
T
E
H
N
O
L
S
E
C
OG
I
T
E
H
N
O
L
S
d
d
B
B
T
C
H
N
E
O
L
O
GIS
E
T
C
H
N
E
O
L
O
GIS
E
553553
OPERA 210D
OPERA 410D
OPERA 210D
OPERA 410D
OPERA 402D
OPERA 405D
OPERA 602D
OPERA 605D
OPERA 402D
OPERA 405D
OPERA 602D
OPERA 605D
ANGOLO DI COPERTURA TROMBA / HORN ANGLE COVERED
HOCHTONHORN ABSTRAHLWINKEL / ANGLE DE COUVERTURE COTE
65°
60°
Long trough
Near field
80°
65°
80°
SCHEMA A BLOCCHI - BLOCK DIAGRAM
BLOCKSCHALTBILD - SCHEMAS FONCTIONNELS
READYLIMITER
Switching Mode
Power Supply
SMPS
SIGNAL
SENSITIVITY
Class D
®
DIGIPRO
DSP
Digital Signal Processing
MICROPROCESSOR
Class D
MODE
WOOFER
DRIVER
BALANCED
INPUTS
LINK
L
N
MAINS
FUSE
POWER
SWITCH
TRANSFORMER
INPUT
SENS
L
N
MAINS
FUSE
POWER
SWITCH
READYLIMITER
SIGNAL
SENSITIVITY
Class D
®
DIGIPRO
DSP
Digital Signal Processing
MICROPROCESSOR
Class D
MODE
WOOFER
DRIVER
BALANCED
INPUTS
LINK
INPUT
SENS
INTERNAL
POWER
SUPPLY
200W
400W
600W
OPERA 208D
OPERA 210D
OPERA 410D OPERA 402D OPERA 405D
OPERA 602D OPERA 605D
54
53
66
UTILIZZO IN APPOGGIO
SUPPORTED USE
ANWENDUNG
UTILISATION EN APPUI
FIG. 3
Fig. 1
Fig. 2
UTILIZZO A PAVIMENTO (MONITOR)
FLOOR USES (MONITOR)
VERWENDUNG AUF DEM BODEN (MONITOR)
UTILISATION AU SOL (ÉCRAN)
56
55
SUPPORTO PIANTANA STANDARD (D36M)
STANDARD STAND (D36MM)
STANDARD-HOCHSTÄNDERFLANSCH (D36MM)
SUPPORT STANDARD (D36MM)
PE
AO
R
PE
AO
R
D
D
B
B
d
d
T G
S
E
O
E
I
CH
N
L
O
T G
S
E
O
E
I
CH
N
L
O
B
B
d
d
T G
S
E
O
E
I
CH
N
L
O
T G
S
E
O
E
I
CH
N
L
O
d
d
B
B
O
I
E
C
H
N
L
O
T G
S
E
O
I
E
C
H
N
L
O
T G
S
E
R
O E
A
P
R
O E
A
P
D
D
B
B
d
d
L
E
C
O
N
G
H
T
I
E
S
O
L
E
C
O
N
G
H
T
I
E
S
O
BB
dd
L
E
C
O
N
G
H
T
I
E
S
O
L
E
C
O
N
G
H
T
I
E
S
O
dd
BB
G
T
I
E
O
H
L
S
E
C
N
O
G
T
I
E
O
H
L
S
E
C
N
O
OP
E
R
AOP
E
R
A
D
D
B
B
d
d
G
I
C
O
L
T
H
E
S
O
N
E
G
I
C
O
L
T
H
E
S
O
N
E
B
B
d
d
G
I
C
O
L
T
H
E
S
O
N
E
G
I
C
O
L
T
H
E
S
O
N
E
d
d
B
B
CO
L
G
I
E
S
T
H
N
E
O
CO
L
G
I
E
S
T
H
N
E
O
P
E
A
O
R
P
E
A
O
R
D
D
B
B
d
d
L
N
G
H
I
O
T
O
E
E
C
S
L
N
G
H
I
O
T
O
E
E
C
S
BB
dd
L
N
G
H
I
O
T
O
E
E
C
S
L
N
G
H
I
O
T
O
E
E
C
S
dd
BB
G
T
E
H I
C O
O
E
L
S
N
G
T
E
H I
C O
O
E
L
S
N
D
B
B
d
d
B
B
d
d
d
d
B
B
APPENDIBILE CON STAFFA (OPZIONALE)
APPENDIX BRACKET (OPTIONAL)
ANHANG BRACKET (OPTIONAL)
ANNEXE BRACKET (FACULTATIF)
Kit completo
Complete kit
Opzione codice / Optional code
WB10 ---> OPERA 210D
OPERA 410D
WB12-15 ---> OPERA 402D
OPERA 405D
OPERA 602D
OPERA 605D
R
A
OPER
A
OPE
DD
BB
dd
OS
L
O
T
E
C
G
E
HNI
OS
L
O
T
E
C
G
E
HNI
BB
dd
OS
L
O
T
E
C
G
E
HNI
OS
L
O
T
E
C
G
E
HNI
dd
BB
OS
L
T
O
E
E
C
H
G
N
I
OS
L
T
O
E
E
C
H
G
N
I
FIG. 4
Anello
Gambo
Punta = Positivo/Caldo/Fase +VE
Anello = Negativo/Freddo/Fase -VE
Punta
Gambo
Punta = Segnale
Gambo=Schemo/Massa/Terra
Funzionamento sbilanciato con
connettore jack 1/4” (6,3mm)
1
2
3
Ingresso
XLR - maschio
Pin 3 =Negativo/Freddo/Fase -VE
1
2
3
Funzionamento sbilanciato con
connettore XLR
Ingresso
XLR - maschio
Pin 2 = Positivo/Caldo/Fase +VE
Pin 1 =Schermo/Terra/Massa
Pin 3 = Connesso al Pin 1
Funzionamento bilanciato con
connettore jack 1/4” (6,3mm)
Gambo=Schemo/Massa/Terra
Punta
Funzionamento bilanciato con
connettore XLR
Pin 2 = Positivo/Caldo/Fase +VE
Pin 1 =Schermo/Terra/Massa
Tip = Positive/Hot/+VE Phase
Balanced use of stereo 1/4” jack plug
Tip
Sleeve
Tip = Signal
Sleeve=Screen/Ground/Earth
Unbalanced use of stereo 1/4” jack plug
Balanced use with XLR connectors
Input
XLR - male
Pin 2 = Positive/Hot/+VE Phase
Pin 3 =Negative/Cold/-VE Phase
Pin 1 =Screen/Ground/Earth
Unbalanced use with XLR connectors
Input
XLR - male
Pin 2 = Positive/Hot/+VE Phase
Pin 1 =Screen/Ground/Earth
Pin 3 = Link to Pin 1
Ring=Negative/Cold/-VE Phase
Sleeve=Screen/Ground/Earth
Sleeve
Ring
Tip
COLLEGAMENTI
CONNECTIONS
ANSCHL
BRANCHEMENTS
ÜSSE
Loading...