Datecs Linea Pro 4.0 Series, Linea Pro 4. MSR 1D, Linea Pro 4.0 MSR, Linea Pro 4. MSR 2D, Linea Pro 4.0 MSR 1D BT User Manual
...
User Manual
iPhone®, iPod®, iPod classic®, iPod nano®, iPod shuffle®, and iPod
touch® are trademarks of Apple Inc., registered in the U.S. and other
countries. iPad™ is a trademark of Apple Inc.
Linea Pro 4.0
. . . . . . . . . . . . . . . . . . . . . .
Legal notice
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an
electronic accessory has been designed to connect specifically to iPod,
iPhone, or iPad, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory
standards. Please note that the use of this accessory with iPod, iPhone,
or iPad may affect wireless performance.
Compatibility
Made for
• iPod touch 4th generation
• iPhone 4
Page 2
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Linea Pro 4.0 Models
Model Description
Linea Pro 4.0 MSR Linea Pro 4.0 4 with 3-Track mag-stripe reader
Linea Pro 4. MSR 1D
Linea Pro 4.0 with 3-Track mag-stripe reader and
1D barcode scanner
Linea Pro 4. MSR 2D
Linea Pro 4.0 MSR 1D BT
Linea Pro 4.0 MSR 2D BT
Linea Pro 4.0 with 3-Track mag-stripe reader and
2D barcode scanner
Linea Pro 4.0 with 3-Track mag-stripe reader and
1D barcode scanner and Bluetooth®
Linea Pro 4.0 with 3-Track mag-stripe reader and
2D barcode scanner and Bluetooth®
Page 3
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Contents
Contents ............................................................................................ 4
Overview............................................................................................ 5
Technical Data...................................................................................6
Box Contents.....................................................................................7
Getting Started.................................................................................. 8
About Your Linea Pro 4.0..................................................................9
Charging Battery.............................................................................11
Status & Operating Modes..............................................................12
Attaching Device.............................................................................13
1D Barcode Scanning .....................................................................14
2D Barcode Scanning .....................................................................15
Replacing Battery............................................................................17
Syncing............................................................................................ 18
Developing Solutions......................................................................19
Troubleshooting.............................................................................. 20
Card Reading..................................................................... 20
Barcode Scanning.............................................................21
Federal Communications Commission..............................................22
Page 4
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Overview
Linea Pro 4.0 allows mobile workers to convert their iPod touch and
iPhone handset into a powerful point-of-sale solution. The Linea Pro
4.0 includes optional 1D or 2D barcode scanner, 3-tracks magnetic
stripe reader, and a rechargeable battery extender in a very compact
and durable protective case.
Features:
Battery: Rechargeable Li-ion Battery - 1300 mAh,
Magnetic Card Reader – 3-Track Head:
Swipe Speed: Minimum of 1.97 in/sec
MTBF: 1 million swipes
Bidirectional reading capabilities
Barcode Scanner - Class II - 1D Laser / 2D Imager:
Single / Multi-scan mode
1D - MTBF: 30K hours
2D - MTBF: 50K hours
Indicators: Audible: Internal electro-magnetic buzzer
Visual: 3 green LEDs
I/O Connectors: 30-pin plug iPod dock connector
10-pin female Mini-B USB connector for charging
and synchronization
Charging via USB to computer or Charging Station
to Linea Pro 4.0, Provides auxiliary power to iPod
touch and iPhone
(Laser Diode & Mirror Unit 10K hours)
(Imager & Laser Pointer & Focus LED)
Page 5
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Technical Data
General Specifications:
Power supply Internal voltage 3.3V & 5V
Operation Modes
MCU Hitachi - HD64F3687
Memory 512k I2C EEPROM memory - for Linea Pro 4.0 settings
Communications
RS232 Interface
Power
consumption
Buttons
Magnetic Stripe
Reader
Barcode Reader
Barcode Type
LEDs 3 green LEDs for status of Battery Charging and status of the Device
Battery
Audio Indicator Electro-Magnetic Buzzer
Weight, g
Dimensions, mm 125mm x 67mm x (19 to 25)mm - depends on scanner 1D/2D & device)
Environment
Cables
Active (turn on Linea Pro 4.0) / Active with Scanning / Stand By (after 5sec
without operate)
RS232 Interface - communication between Linea Pro 4.0 & iPod /iPhone
USB Interface - USB Synchronization between iPhone / iPod & PC
Speed: 57600bps
iPod RS232 Protocol
Active with Scanning: 1D Engine – 110mA; 2D Engine - 230mA
Active - approximately 25mA
Stand by - 10µA
Volume Up Button, Volume Down Button, Status Battery Button,
Scan Button
3-track bidirectional reading capabilities
Type: ISO 7816-1/2/3 compatible & RAW mode
MDL-1000 - Laser Scan Engine 1D Barcode
MDI-2000 – Auto-focus Imager Scan Engine 2D Barcode
UCC/EAN 128, EAN 13, EAN 8, UPC A, UPC E, UPC E1, Code 11, Code
39, Code 93, Code 128, GS1, Matrix 2 to 5, Code 11,2 of 5 industrial, 2
of 5 interleaved, Codebar, MSI/Plessey, UK/Plessey, IATA,ISBN, ISMN,
ISSN, S-code, Telepen, RSS 14, RSS Limited, RSS- Expanded, PDF417,
microPDF417, Data Matrix, QR code, Aztec code, Maxi code, Micro QR
code
Rechargeable Li-ion Battery 3.7V/1300mAh
1D: Over 14,000 scan and swipes per full charge
2D: Over 8,000 scan and swipes per full charge
95 grams without iPod / iPhone
230 grams with iPhone
197 grams with iPod
- Operating temperature 0°C to +40°C
- Operating humidity 35 to 85% RH
- Storage temperature -5°C to +40°C
- Storage humidity 10 to 90% RH
Standard USB A to mini B CABLE
USB DOWNLOAD CABLE (option)
Table 1
* Specifications subject to change without notice.
Page 6
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Box Contents
Your Linea Pro 4.0 comes with the following items listed below:
Item Part Number Descriptions Image
1 Linea Pro 4.0 4
2 CABDAT001240 USB sync cable
Pro 4.0 User
3
Manual
*Bulk Shipments may ship without cables and manuals in each box.
Software ( Drivers & SDK ):
Because of the continually evolving SDK, the latest SDK are not
distributed on CD.
For the latest Linea Pro 4.0 SDK’s, please visit our Linea Pro
developer portal:
ftp://ftp.datecs.bg/pub/Java/SDKM
Linea Pro 4.0 Reader
/ Scanner
User's manual
Table 2
Page 7
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Getting Started
The Linea Pro 4.0 allows you to scan barcode and capture Magnetic
Strip information onto your iPod and iPhone. Before using your Linea
Pro 4.0 the battery should be properly charged. The following Quick
Start guide will help to get your Linea Pro 4.0 ready for use.
Quick Start:
Step What to do Purpose
Fully charge your
Linea Pro 4.0 as
1
recommended.
Install Software.
2
Attach device to
3
Linea Pro 4.0.
The battery pack
should be fully
charged before use
to ensure long
battery life.
Barcode Scanning
& Card Reading
requires software
to be installed onto
your iPod or
iPhone.
Connecting your
Linea Pro and
iPod, iPhone.
Table 3
Where to find more
information
Charging Battery,
Page 10.
Software is not
provided with Linea
Pro 4.0. Please
contact your reseller
for recommendations
on Third-Party
software solutions.
Developers should
refer to the section in
this manual on
“Developing
Solutions” Page 18.
Attaching Device,
Page 12.
Page 8
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
About Your Linea Pro 4.0
Volume Controls
Scan Button
On/Off
USB
Sync / Charge Port
Scan Engine
Audio Connector
♦ Linea Pro 4.0 (Right side)
♦ Linea Pro 4.0 (Left side)
Figure 1
Figure 2
Page 9
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
About Your Linea Pro 4.0
MSR Reader
Scan Engine
Scan Button
♦
Linea Pro 4.0
(Bottom side)
User Notes:
Special software must be used to process the information captured by
the barcode scanner and magnetic strip reading feature. Please
consult your reseller for this software or contact Infinite Peripherals for
recommendations on compatible third party software solutions.
Figure 3
Page 10
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Charging Battery
1 LED
Charging the Linea Pro 4.0:
The Linea Pro 4.0 uses a Lithium Ion rechargeable battery pack. Before
first use, the battery pack should be charged for at least (4) hours.
To prevent electrical damage to the Linea Pro 4.0 and/or battery pack,
please use approved USB to Mini USB cables only.
Charging via USB cable
(type A to mini USB), connected
Figure 4
Figure 5
to PC 5V/260mA
= 33 % of full charge
2 LED = 66 % of full charge
3 LED = 100 % of full charge
Page 11
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Status & Operating Modes
Battery
The Linea Pro 4.0 uses the battery indicator LEDs to indicate various
conditions of operation. Possible LED lighting indications may result
from charging, active/online status, or because of low battery. The
following table and figure explain these conditions and LED indication.
Figure 6
Operating Status
Status Button
All LED is OFF
Middle LED is FLASHING
Multiple LED is ON
Page 12
Linea Pro 4.0 User Manual v1.00
Linea Pro 4 is in sleep or ready
mode
Linea Pro 4.0 is in sync mode
Linea Pro 4.0 is displaying
battery level status
Table 4
. . . . . . . . . . . . . . . . . . . . . .
Attaching Device
When using the Linea Pro 4.0, care must be taken to ensure the Linea
Pro 4.0 30 pin connector and the iPod and iPhone connector are not
accidentally damaged. The figures below show how to attach your
device to the Linea Pro 4.0.
1: Unlock the top cover as shown in figure above.
2: Slide the device as shown in the figure above.
3: Replace the top cover as shown in the figure above.
Figure 7
Figure 8
Figure 9
Page 13
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
1D Barcode Scanning
Using the 1D barcode scanner:
The Linea Pro 4.0 1D uses a scan engine that supports onedimensional (1D) barcode symbols. The effective reading distance of
the barcode reader varies depending on the barcode size.
Scanning 1D Barcodes:
To scan a 1D barcode fist activate the scanner. Then position the scan
head as close to the barcode label as possible so that the scan line
crosses both ends of the barcode as shown in the figure below.
Slowly pull back the unit increasing the distance between the barcode
and scan head until the barcode has been read by the scanner.
~ 15-20 cm
Scan button
Figure 10
Page 14
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
2D Barcode Scanning
Using the 2D barcode scanner:
The Linea Pro 4.0 2D uses a scan engine that supports onedimensional (1D) and two-dimensional (2D) barcode symbols. The
effective reading distance of the barcode reader varies depending on
the barcode size.
Scanning 2D Barcodes:
To scan a 2D barcode fist activate the scanner. Then position the scan
head to center the red aiming laser near the center of the barcode and
the illumination box is over the outer edges of the barcode as shown in
the figure below.
Slowly pull back the unit increasing the distance between the barcode
and scan head until the barcode has been read by the scanner.
Page 15
Linea Pro 4.0 User Manual v1.00
~ 15-20 cm
Scan button
Figure 11
. . . . . . . . . . . . . . . . . . . . . .
Card Reading
Reading Magnetic Strips:
The Linea Pro 4.0 has a built-in magnetic card reader. The card reader
incorporates a (3) track magnetic read head requiring a single swipe to
read field data from all three tracks.
The magnetic read head faces up towards the top of the cradle. When
placing the card into the reader, the magnetic strip must be facing up as
shown in the figure below. Keep the edge of the card flat on the inner
base of the reader to ensure that the magnetic strip passes over the
read head evenly.
Figure 12
User Notes:
To use the magnetic card reader feature, special software must be used
to read and process the card information. Please consult your reseller if
this software is available for recommendations on compatible third party
software solutions.
Swipe direction
Page 16
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Replacing Battery
To replace the Linea Pro 4.0 battery, follow the steps below.
1. Remove the device as shown in the figure below.
2. Squeeze battery cover latch to the left as shown in the figure above.
3. Lift the battery cover as shown in the figure above. Remove the existing
Battery pack. Reverse Steps 1-2 to install the new battery pack.
Notice: Use only factory recommended replacement battery to prevent
Figure 13
Figure 14
damage to the Linea Pro 4.0.
Page 17
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Syncing
The Linea Pro 4.0 portable barcode scanner and card reader is
designed specifically for use with iPod/iPhone there by allowing the iPod
and iPhone to sync with iTunes through the Linea Pro 4.0 while
connected.
To sync iPod with iTunes through the Linea Pro 4.0 follow the steps
below;
1. Connect the Linea Pro 4.0 to a computer using a Mini USB cable
2. Wait for the sync mode 2-beeps and the center LED flashes green.
The Linea Pro 4.0 should now be in sync mode. Refer to the iTunes
documentation for syncing your iPod and iPhone.
To disable sync mode, exit iTunes then unplug the Linea Pro 4.0 from
the Mini USB cable.
Page 18
Linea Pro 4.0 User Manual v1.00
as shown in the figure below.
Sync Mode LED
Figure 15
. . . . . . . . . . . . . . . . . . . . . .
Developing Solutions
Integrating the Linea Pro 4.0 into your solution requires the use of the
Linea Proro 4.0 SDK. The SDK incorporates an API specifically for
developing application to use the barcode scanning and card reading
capability of the Linea Pro 4.0.
For details on using the Linea Pro 4.0 SDK, please refer to the SDK’s
documentation.
For the latest Linea Pro 4.0 SDK’s, please visit our Linea Pro
developer portal:
ftp://ftp.datecs.bg/pub/Java/SDKM
Page 19
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Troubleshooting
Card Reading
If you are having problems with reading card magnetic strip refer to the
table below for possible causes.
Item Problem Possible Cause
No card data
1
returned during
swiping.
Partial card data
2
returned during
swiping.
* Linea Pro 4.0 not turned On.
* Card inserted incorrectly.
* Swipe method incorrect.
* Faulty read head.
* Unreadable magnetic strip.
* Swipe method incorrect.
* Faulty read head.
* Unreadable magnetic strip.
Table 5
Page 20
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Troubleshooting
Barcode Scanning
If you’re having problems scanning barcodes refer to the table below for
possible causes.
Item Problem Possible Cause
Scanner does not
1
turn On.
No barcode data
returned during
2
scanning.
Partial barcode
data returned
3
during scanning.
* Linea Pro 4.0 battery is to low.
* Linea Pro 4.0 not turned on by
software.
* Faulty scan engine.
* Unreadable barcode.
* Linea Pro 4.0 battery is to low.
* Faulty scan engine.
* Software decode incorrectly.
* Unreadable barcode.
* Linea Pro 4.0 battery is to low.
* Faulty scan engine.
* Software decode incorrectly.
Unable to perform
4
multi-scanning.
Unable to hear
5
scanner beep.
Unable to scan
certain barcodes
6
symbols.
* Multi-scan mode not enabled.
* Software does not support multi-scans.
* Sound mode not enabled.
* Linea Pro 4.0 battery is to low.
* Barcode type is not enabled.
* Barcode type is not supported.
Table 6
Page 21
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
Federal Communications Commission
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
tat to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Page 22
Linea Pro 4.0 User Manual v1.00
. . . . . . . . . . . . . . . . . . . . . .
FCC Continued
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Page 23
Linea Pro 4.0 User Manual v1.00
Loading...