How it Works
Datasheet
Loading...
TDA7021T
Datasheet (Philips)
13 pgs146.41 Kb0
Specification
13 pgs159.87 Kb0
Table of contents
Loading...

Datasheet TDA7021T Datasheet (Philips)

Download
Page 1
INTEGRATED CIRCUITS
DATA SH EET
TDA7021T
FM radio circuit for MTS
Product specification File under Integrated Circuits, IC01
May 1992
Page 2
FM radio circuit for MTS TDA7021T

GENERAL DESCRIPTION

The TDA7021T integrated radio receiver circuit is for portable radios, stereo as well as mono, where a minimum of periphery is important in terms of small dimensions and low cost. It is fully compatible for applications using the low-voltage micro tuning system (MTS). The IC has a frequency locked loop (FLL) system with an intermediate frequency of 76 kHz. The selectivity is obtained by active RC filters. The only function to be tuned is the resonant frequency of the oscillator. Interstation noise as well as noise from receiving weak signals is reduced by a correlation mute system.
Special precautions have been taken to meet local oscillator radiation requirements. Because of the low intermediate frequency, low pass filtering of the MUX signal is required to avoid noise when receiving stereo. 50 kHz roll-off compensation, needed because of the low pass characteristic of the FLL, is performed by the integrated LF amplifier. For mono application this amplifier can be used to directly drive an earphone. The field-strength detector enables field-strength dependent channel separation control.

Features

• RF input stage
• Mixer
• Local oscillator
• IF amplifier/limiter
• Frequency detector
• Mute circuit
• MTS compatible
• Loop amplifier
• Internal reference circuit
• LF amplifier for
− mono earphone amplifier or
− MUX filter
• Field-strength dependent channel separation control
facility

QUICK REFERENCE DATA

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Supply voltage (pin 4) V Supply current V
= 3 V l
P
RF input frequency f
= V
P 4 rf
1,8 − 6,0 V
4-3
− 6,3 − mA 1,5 − 110 MHz
Sensitivity (e.m.f.) for source impedance = 75 Ω;
−3 dB limiting mute disabled EMF − 4 −µV Signal handling (e.m.f.) source impedance = 75 Ω EMF − 200 − mV AF output voltage V
o
− 90 − mV

PACKAGE OUTLINE

16-lead mini-pack; plastic (SO 16; SOT109A); SOT109-1; 1996 July 24.
May 1992 2
Page 3
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
May 1992 3
Philips Semiconductors Product specification
FM radio circuit for MTS TDA7021T
Fig.1 Block diagram.
Page 4
FM radio circuit for MTS TDA7021T

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)
PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT
Supply voltage (pin 4) V Oscillator voltage V Storage temperature range T Operating ambient temperature range T

THERMAL RESISTANCE

P 5-4 stg amb
= V
4-3
− 7,0 V VP−0,5 VP+ 0,5 V
−55 +150 °C
−10 +70 °C
From junction to ambient R

DC CHARACTERISTICS

= 3 V, T
V
P
= 25 °C, measured in circuit of Fig.4, unless otherwise specified
amb
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Supply voltage (pin 4) V Supply current V
= 3 V I
P
Oscillator current I Voltage at pin 13 V Output voltage (pin 14) V
4 5
P
13-3 14-3
= V
4-3
1,8 3,0 6,0 V
− 6,3 − mA
− 250 −µA
− 0,9 − V
− 1,3 − V
th j-a
300 K/W
Fig.2 Supply current as a function of the supply voltage.
May 1992 4
Page 5
FM radio circuit for MTS TDA7021T

AC CHARACTERISTICS (MONO OPERATION)

V
= 3 V; T
P
(e.m.f. at a source impedance of 75 Ω); r.m.s. noise voltage measured unweighted (f = 300 Hz to 20 kHz); unless otherwise specified
Sensitivity (e.m.f.) see Fig.3
for −3 dB limiting muting disabled EMF − 4,0 −µV for −3 dB muting EMF − 5,0 −µV for (S+N)/N = 26 dB EMF − 7,0 −µV
Signal handling (e.m.f.) THD < 10%;
Signal-to-noise ratio (S+N)/N − 60 − dB Total harmonic distortion ∆f = ± 22,5 kHz THD − 0,7 − %
AM suppression of output
voltage ratio of AM signal
Ripple rejection ∆V
Oscillator voltage (r.m.s. value) V Variation of oscillator frequency
with temperature V
Selectivity see Fig.9;
AFC range ±∆f Mute range ±∆f Audio bandwidth ∆V
AF output voltage
(r.m.s. value) R
AF output current
max. d.c. load I max. a.c. load (peak value) THD = 10% I
= 25 °C; measured in Fig.5; frf = 96 MHz modulated with ∆f = ±22,5 kHz; fm = 1 kHz; EMF = 0,3 mV
amb
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
∆f = ± 75 kHz EMF − 200 − mV
∆f = ± 75 kHz THD − 2,3 − %
(f
= 1 kHz; m = 80%)
m
to FM signal (f
=
m
1 kHz; ∆f = 75 kHz) AMS − 50 − dB
= 100 mV;
P
f = 1 kHz RR − 30 − dB
5-4(rms)
= 1 V − 5 − kHz/°C
P
no modulation S
= 3 dB;
o
∆f
osc
---------------- ­T
∆
amb
+300
S
−300 rf rf
− 250 − mV
− 46 − dB
− 30 − dB
− 160 − kHz
− 120 − kHz
measured with 50 µs pre-emphasis B − 10 − kHz
(pin 14) = 100 Ω V
L
o(rms)
o(dc) o(ac)
− 90 − mV
−100 −+100 µA
− 3 − mA
May 1992 5
Page 6
FM radio circuit for MTS TDA7021T
Fig.3 Field strength voltage (V
9-3
) at R
= 1 kΩ; f = 96,75 MHz; VP = 3 V.
source
Fig.4 Mono operation: AF output voltage (Vo) and total harmonic distortion (THD) as functions of input e.m.f.
(EMF); R
= 75 Ω; frf = 96 MHz; 0 dB = 90 mV. For S+N and noise curves (1) is with muting enabled
source
and (2) is with muting disabled; signal ∆f = ± 22,5 kHz and fm = 1 kHz. For THD curve, ∆f = ± 75 kHz and fm = 1 kHz.
May 1992 6
Page 7
FM radio circuit for MTS TDA7021T
1) The AF output can be decreased by disconnecting the 100 nF capacitor from pin 16.
Fig.5 Test circuit for mono operation.

AC CHARACTERISTICS (STEREO OPERATION)

V
= 3 V; T
P
∆f=±22,5 kHz; f
= 25 °C; measured in Fig.8; frf = 96 MHz modulated with pilot ∆f = ± 6,75 kHz and AF signal
amb
= 1 kHz; EMF = 1 mV (e.m.f. at a source impedance of 75 Ω); r.m.s. noise voltage measured
m
unweighted (f = 300 Hz to 20 kHz); unless otherwise specified
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Sensitivity (e.m.f.) for (S+N)/N = 26 dB see Fig.8; pilot off EMF − 11 −µV Selectivity see Fig.9; no modulation S
S
+300
−300
− 40 − dB
− 22 − dB
Signal-to-noise ratio (S+N)/N − 50 − dB Channel separation V
= L-signal; fm = 1 kHz; pilot on:
i
at f
= 97 MHz α−26 − dB
rf
at f
= 87,5 MHz and 108 MHz α−14 − dB
rf
May 1992 7
Page 8
FM radio circuit for MTS TDA7021T
Fig.6 Stereo operation: signal/noise and channel separation of TDA7021T when used in the circuit of Fig.8.
Fig.7 Stereo operation: channel separation as a function of audio frequency in the circuit of Fig.8.
May 1992 8
Page 9
FM radio circuit for MTS TDA7021T
Fig.8 Stereo application in combination with a low voltage PLL stereo decoder (TDA7040T) and a low voltage
mono/stereo power amplifier (TDA7050T).
May 1992 9
Page 10
FM radio circuit for MTS TDA7021T
Fig.9 Test set-up; Vi = 30 mV; fi = 76 kHz; selective voltmeter at output has Ri≥ 1 MΩ and Ci≤ 8 pF; fo = fi.
Note to Fig. 9
This test set-up is to incorporate the circuit of Fig.5 for mono operation or the circuit of Fig.8 for stereo operation. For either circuit, replace the 100 nF capacitor at pin 6 with R6 (100 kΩ) as shown above.

Selectivity

S
+300
= 20 log
| (300 kHz − fi)
V
o
| f
V
o
i
S
−300
= 20 log
| (300 kHz + fi)
V
o
Vo| f
i
May 1992 10
Page 11
FM radio circuit for MTS TDA7021T

PACKAGE OUTLINE

SO16: plastic small outline package; 16 leads; body width 3.9 mm
D
c
y
Z
16
pin 1 index
1
e
9
8
w M
b
p

SOT109-1

E
H
E
A
2
A
1
L
detail X
A
X
v M
A
Q
(A )
L
p
A
3
θ
0 2.5 5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
mm
OUTLINE VERSION
SOT109-1
A
max.
1.75
0.069
A1A2A
0.25
1.45
0.10
1.25
0.010
0.057
0.004
0.049
3
0.25
0.01
IEC JEDEC EIAJ
076E07S MS-012AC
b
p
0.49
0.36
0.019
0.014
0.25
0.19
0.0100
0.0075
UNIT
inches
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
(1)E(1) (1)
cD
10.0
4.0
3.8
0.16
0.15
1.27
0.050
9.8
0.39
0.38
REFERENCES
May 1992 11
eHELLpQZywv θ
1.05
0.041
1.0
0.4
0.039
0.016
0.7
0.25
0.6
0.028
0.01 0.004
0.020
EUROPEAN
PROJECTION
0.25 0.1
0.01
0.7
0.3
0.028
0.012
ISSUE DATE
95-01-23 97-05-22
o
8
o
0
6.2
5.8
0.244
0.228
Page 12
FM radio circuit for MTS TDA7021T
SOLDERING Introduction
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used.
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our
“IC Package Databook”
Reflow soldering
Reflow soldering techniques are suitable for all SO packages.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 °C.
(order code 9398 652 90011).
During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured.
Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally­opposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C.
Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C.
Wave soldering
Wave soldering techniques can be used for all SO packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used.
• The longitudinal axis of the package footprint must be parallel to the solder flow.
• The package footprint must incorporate solder thieves at the downstream end.
May 1992 12
Page 13
FM radio circuit for MTS TDA7021T

DEFINITIONS

Data sheet status
Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
May 1992 13
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use