The NE4210S01 is a Hetero Junction FET that utilizes the hetero junction to create high mobility electrons. Its
excellent low noise and associated gain make it suitable for DBS and another commercial systems.
FEATURES
• Super Low Noise Figure & High Associated Gain
NF = 0.5 dB TYP. Ga = 13.0 dB TYP. @f = 12 GHz
• Gate Length: Lg ≤ 0.20 µm
• Gate Width : Wg = 160 µm
ORDERING INFORMATION (PLAN)
Part NumberMarkingSupplying Form
NE4210S01-T1Tape & reel 1 kp/reel
NE4210S01-T1B
Remark
To order evaluation samples, please contact your local NEC sales office. (Part number for sample order:
L
Tape & reel 4 kp/reel
NE4210S01)
ABSOLUTE MAXIMUM RATINGS (TA = +25°C)
ParameterSymbolRatingsUnit
Drain to Source VoltageV
Gate to Source VoltageV
Drain CurrentI
Gate CurrentI
Total Power Dissipat i onP
Channel TemperatureT
Storage TemperatureT
DS
GS
D
G
tot
ch
stg
4.0V
–3.0V
DSS
I
100
165mW
125°C
–65 to +125°C
RECOMMENDED OPERATING CONDITIONS (TA = +25°C)
ParameterSymbolMIN.TYP.MAX.Unit
mA
µ
A
Drain to Source VoltageV
Drain CurrentI
Input PowerP
The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for
availability and additional information.
Document No. P14232EJ2V0DS00 (2nd edition)
Date Published November 1999 N CP(K)
Printed in Japan
(1) Because this device is a GaAs MES FET with a Schottky barrier gate structure, it is necessary that sufficient
care be taken regarding static electricity and strong electric fields.
Take measures against static electricity and make sure the body is earthed when mounting the device.
(2) Follow the procedure below when operating the device by a gate-and-drain-independent dual power supply.
Directly ground both the source pins.
VGS = fixed to approximately –4 V.
Increase VDS to a predetermined voltage level (within the recommended operating range of VDS).
Adjust VGS in line with a predetermined ID.
(3) It is recommended that the bias application circuit be able to have a fixed voltage and current.
(4) Adjust the I/O matching circuit after turning the bias OFF.
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered under the following recommended conditions. For soldering methods and
conditions other than those recommended below, contact your NEC sales representative.
Soldering MethodSoldering ConditionsRecommended Condition Symbol
Infrared ReflowPackage peak temperature: 230 °C or below
Time: 30 seconds or less (at 210 °C)
Count: 1, Exposure limit : None
Partial HeatingPin temperature: 230 °C
Time: 10 seconds or less (per pi n row)
Exposure limit : None
After opening the dry pack, keep it in a place below 25 °C and 65 % RH for the allowable storage period.
Note
Note
Note
IR30-00-1
–
Caution Do not use different soldering methods together (except for partial heating).
14
Data Sheet P14232EJ2V0DS00
Page 15
[MEMO]
NE4210S01
Data Sheet P14232EJ2V0DS00
15
Page 16
NE4210S01
CAUTION
The Great Care must be taken in dealing with the devices in this guide.
The reason is that the material of the devices is GaAs (Gallium Arsenide), which is
designated as harmful substance according to the law concerned.
Keep the law concerned and so on, especially in case of removal.
• The information in this document is subject to change without notice. Before using this document, please
confirm that this is the latest version.
• No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
• NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property
rights of third parties by or arising from use of a device described herein or any other liability arising from use
of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of NEC Corporation or others.
• Descriptions of circuits, software, and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these circuits,
software, and information in the design of the customer's equipment shall be done under the full responsibility
of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third
parties arising from the use of these circuits, software, and information.
• While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
• NEC devices are classified into the following three quality grades:
"Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a
customer designated "quality assurance program" for a specific application. The recommended applications of
a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device
before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact an NEC sales representative in advance.
M7 98. 8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.