Datasheet IHB60T480515, IHB60T480312, IHB60T240515, IHB60T240512, IHB60T240315 Datasheet (cdtechno)

Corporate: www.cd techno.com

Corporate: www.cd techno.com

Product: www.cdpowerelectronics.com

IHB60T

60 Watt Triple Output Half Brick DC/DC Converter

 18 - 40 & 33 - 75V Input

Range

 Each Channel Independently

Current Limited

 High Efficiency: 87% Typical
 1500VDC Isolation Between

Input and Output

 Operation to 100°C Baseplate

Temperature

 50µS Transient Recovery,

0-90% Load Step

 Primary & Secondary Remote

On/Off

 IHB60T48 Series Approved to

UL/CUL 1950, EN60950

The IHB60T series triple output standard half brick modules are de­signed for today’s demanding industrial applications. Available in two
wide range inputs, these isolated converters offer many features in the
standard models. With a complement of safety agency approvals and low
noise operations, the converters respond extremely fast to change in load
conditions. Inherent in the design are very well-controlled output volt­ages and minimal need for minimum loading on main (V1) output.

PRODUCT SELECTION CHART

INPUT

VOLTAGE RATED VOUT (VDC) RATED MAXIMUM IOUT (A)

MODEL (VDC) V1 (±) V2 (±) V3 (±) V1(±) V2(±) V3(±)

IHB60T240312 24 (18-40) 3.3 12 12 18 2.5 2.5
IHB60T240315 24 (18-40) 3.3 15 15 18 2.0 2.0
IHB60T240512 24 (18-40) 5.1 12 12 12 2.5 2.5
IHB60T240515 24 (18-40) 5.0 15 15 12 2.0 2.0
IHB60T480312 48 (33-75) 3.3 12 12 18 2.5 2.5
IHB60T480315 48 (33-75) 3.3 15 15 18 2.0 2.0
IHB60T480512 48 (33-75) 5.1 12 12 12 2.5 2.5
IHB60T480515 48 (33-75) 5.0 15 15 12 2.0 2.0

ABSOLUTE MAX.

RA TINGS

Output Short-Circuit
Duration Continuous

Baseplate Temperature +100°C
Lead Temperature

(soldering, 10 seconds max) +300°C
Storage Temperature +125°C
Input to Output Isolation 1500 VDC

EFFICIENCY vs TEMPERATURE

T

= +40°C, nominal input voltage, nominal load, recommended external

CASE

components applied, unless otherwise specified.*

Change in Efficiency (%)

Case Temperature (°C)

SPECIFICATIONS, ALL MODELS

Specifications are at T

PARAMETER CONDITIONS MIN TYP MAX UNITS

Voltage Range

IHB60T24XX Series 18 24 40 V

IHB60T48XX Series 33 48 75 VDC
Reflected Ripple Current Peak - Peak 220 mA
Input Ripple Rejection DC to 1KHz 50 60 dB
Maximum Input Current Output Power = 60W

IHB60T24XX Series V

IHB60T48XX Series V

INPUT

No Load Power Dissipation P
Inrush Charge

IHB60T24XX Series 0.29 mC

IHB60T48XX Series 0.165 mC
Quiescent Operating Current
Primary On/Off Disabled 7.5 10 mA

Secondary On/Off Disabled 15 25 mA

PARAMETER CONDITIONS MIN TYP MAX UNITS

ISOLATION

Input to Output Peak Test 1500 V
Input to Baseplate 1500 VDC
Channel to Channel Any Channel to Any Channel 500 VDC
Resistance, Input - Output 10 MΩ
Capacitance, Input - Output 2000 pF

Leakage Current V

GENERAL

Set Point Accuracy V
Turn-on Time Within 1% of Nominal V
Remote On/Off Control Inputs
Primary Open Collector/Drain
Sink Current-Logic Low V
Vlow 0.8 V
Vhigh Open Collector
Secondary Open Collector/Drain
Sink Current-Logic Low 100 µA
Vlow 0.4 V
Vhigh Open Collector

GENERAL

External Synchronization Input
Frequency 440 520 KHz
Pulse Width 150 320 nSec
Source Impedence 47 Ω
Input High Voltage 4 5 V
Input Low Voltage 0 1 V
Input Impedance 470 Ω
Switching Frequency 470 480 490 KHz

Weight 3 (85) oz (g)

TEMPERATURE Case Temperature

Operation/Specification -40 +100 °C
Storage -55 +125 °C
Shutdown +100 +115 °C

Thermal Inpedance Case to Ambient 8.2 °C/W

= +40°C nominal input voltage unless otherwise specified.

CASE

= 16V 6 A

IN

= 30V 3 A

IN

= 0, V

OUT

IN, Min<VIN<VIN, Max

= 240VAC, 60Hz 180 µA, rms

ISO

= Nominal, 50% Load 1 %

IN

= V

IN

OUT

MAX

6W

3.5 5 mSec

7mA

DC

DC

PARAMETER CONDITIONS

V1 V2 V3 UNITS

Min Nom Max Min Nom Max Min Nom Max

Output Power Total Combined O/P Power =

60 Watts Max. 30 60 15 30 15 30 W
Set Point Voltage I
Output Current, I
Output Ripple, p-p DC to 20MHz

OUT

Output Adjust Range

O Nom

* 3.15 3.80 Dependent on V1 V

* 100 200 150 250 150 250 mV

3.3 12.2 12.2 V

0.5 9 18 0 1.25 2.5 0 1.25 2.5 A

Output Temperature Drift .02 .05 .02 .05 .02 .05 %/°C
Line Regulation V

Load Regulation Min Load to Rated Load 0.50 1.0 %
Current Limit Inception Other Outputs Min Load 23 5.0 5.0 A

IN, Min≤VIN≤VIN, Max

IO = I

O, Nom

0.05 1.0 1.0 2.0 1.0 2.0 %
See Regulation Curves See Regulation Curves

Short-Circuit Current 19 25 4.0 5.0 4.0 5.0 A
Transient Response 50 to 100% Load Step
Peak Deviation 150 250 mV
Settling Time V

IHB60TX0312** OUTPUT

Overvoltage Limit 4.2 5.0 V
Efficiency I

OUT1

, 1% of V

OUT

=9A, (I

F.L. V

OUT, Nom

)=2.5A 85 86 %

OUT2+IOUT3

=Nominal

IN

35 50 µSec

* See Application Notes available on the web at www.cdpowerelectronics.com
**X = Either 24 or 48

Product: www.cdpowerelectronics.com

IHB60T REV A 10/01

2

SPECIFICATIONS, ALL MODELS

Specifications are at T

PARAMETER CONDITIONS

Output Power Total Combined O/P Power =

Set Point Voltage I
Output Current, I
Output Ripple, p-p DC to 20MHz
Output Adjust Range See Application Notes
Output Temperature Drift .02 .05 .02 .05 .02 .05 %/°C
Line Regulation V

Load Regulation Min Load to Rated Load 0.50 1.0 %
Current Limit Inception Other Outputs Min Load 23 4.0 4.0 A
Short-Circuit Current 19 25 3.2 4.0 3.2 4.0 A
Transient Response 50 to 100% Load Step
Peak Deviation 150 250 mV
Settling Time V
Overvoltage Limit 4.2 5.0 V

IHB60TX0315** OUTPUT

Efficiency I

= +40°C nominal input voltage unless otherwise specified.

CASE

V1 V2 V3 UNITS

Min N o m Max Min N om Max Min Nom Max

60 Watts Max. 30 60 15 30 15 30 W

3.3 15.85 15.85 V

0.5 9 18 0 1 2 0 1 2 A

OUT

O Nom

* 100 200 125 250 125 250 mV

* 3.15 3.80 Dependent on V1 V

IN, Min≤VIN≤VIN, Max

OUT1

, 1% of V

OUT

=9A, (I

F.L. V

IO = I

OUT2+IOUT3

=Nominal

IN

O, Nom

OUT, Nom

)=2A 85 86 %

0.05 1.0 1.0 2.0 1.0 2.0 %

35 50 µSec

See Regulation Curves See Regulation Curves

PARAMETER CONDITIONS

V1 V2 V3 UNI TS

Min Nom Max Min Nom Max Min Nom Max

Output Power Total Combind O/P Power =

60 Watts Max 30 60 15 30 15 30 W
Set Point Voltage I
Output Current, I
Output Ripple, p-p DC to 20MHz

OUT

Output Adjust Range

O Nom

* 4.75 5.50 Dependent on V1 V

* 125 200 150 250 150 250 mV

5.1 12 12 V

0.5 6.0 12 0 1.25 2.5 0 1.25 2.5 A

Output Temperature Drift .02 .05 .02 .05 .02 .05 %/°C
Line Regulation V

Load Regulation Min Load to Rated Load 0.50 1.0 %

IN, Min≤VIN≤VIN, Max

IO = I

O, Nom

0.05 0.10 1.0 2.0 1.0 2.0 %
See Regulation Curves

See Regulation Curves

Current Limit Inception Other Outputs Min Load 16 5.0 5.0 A
Short-Circuit Current 12.6 16 4.0 5.0 4.0 5.0 A
Transient Response 50 to 100% Load Step
Peak Deviation 200 300 mV
Settling Time V
Overvoltage Limit 6.0 6.8 V

IHB60TX0512** OUTPUT

Efficiency I

PARAMETER CONDITIONS

OUT1

, 1% of V

OUT

=6A, (I

F.L. V

OUT, Nom

)=2.5A 86 87 %

OUT2+IOUT3

=Nominal

IN

35 50 µSec

V1 V2 V3 UNITS

Min Nom Max Min Nom Max Min Nom Max

Output Power Total Combined O/P Power =

60 Watts Max 30 60 15 30 15 30 W
Set Point Voltage I
Output Current, I
Output Ripple, p-p DC to 20MHz

OUT

Output Adjust Range

O Nom

* 4.60 5.50 Dependent on V1 V

* 100 200 125 250 125 250 mV

5.0 15.3 15.3 V

0.5 6 12 0 1 2 0 1 2 A

Output Temperature Drift .02 .05 .02 .05 .02 .05 %/°C
Line Regulation V

Load Regulation Min Load to Rated Load 0.50 1.0 %
Current Limit Inception Other Outputs Min Load 16 4.0 4.0 A

IN, Min≤VIN≤VIN, Max

IO = I

O, Nom

0.05 0.10 1.0 2.0 1.0 2.0 %
See Regulation Curves See Regulation Curves

Short-Circuit Current 12.6 16 3.2 4.0 3.2 4.0 A
Transient Response 50 to 100% Load Step
Peak Deviation 200 300 mV
Settling Time V
Overvoltage Limit 6.0 6.8 V

IHB60TX0515** OUTPUT

Efficiency I

OUT1

, 1% of V

OUT

=6A, (I

F.L. V

OUT, Nom

)=2A 86 87 %

OUT2+IOUT3

=Nominal

IN

35 50 µSec

* See Application Notes available on the web at www.cdpowerelectronics.com
**X = Either 24 or 48

Product: www.cdpowerelectronics.com

IHB100T REV A 10/01

3

MECHANICAL

PIN SIDE
DOWN

PIN SIDE UP

SIDE
VIEW

PIN CONNECTIONS

1 PRIMARY ON/OFF
2-VIN
3+VIN
4 SYNC IN
5 -V2
6 +V2
7 TRIM
8 +V1
9 -V1
10 SECONDARY ON/OFF
11 +V3
12 -V3

NOTES:

All dimensions are in inches (millimeters).
PIN PLACEMENT TOLERANCE: ± 0.005"
MECHANICAL TOLERANCE: ± 0.015"
Marked with: specific model ordered, date code, job code.

MATERIAL: Units are encapsulated in a low thermal resistance molding
compound which has excellent chemical resistance and electrical
properties in high humidity environments and over a wide operating
temperature range. The encapsulant and outer shell of the unit have
UL94V-0 ratings. Lead material is solder plated to allow ease of
solderability.

C&D Technologies (Power Electronics) Ltd.

Shannon, Co. Clare, Ireland

T el: +353.61.474.133 Fax:[phone]

Any data, prices, descriptions or specifications presented herein are subject to revision by C&D Technologies, Inc. without notice. While such information is believed to
be accurate as indicated herein, C&D Technologies, Inc. makes no warranty and hereby disclaims all warranties, express or implied, with regard to the accuracy or
completeness of such information. Further, because the product(s) featured herein may be used under conditions beyond its control, C&D Technologies, Inc. hereby
disclaims all warranties, either express or implied, concerning the fitness or suitability of such product(s) for any particular use or in any specific application or arising from
any course of dealing or usage of trade. The user is solely responsible for determining the suitability of the product(s) featured herein for user’s intended purpose and
in user’s specific application. C&D Technologies, Inc. does not warrant or recommend that any of its products be used in any life support or aviation or aerospace
applications.

Product: www.cdpowerelectronics.com

Power Electronics Division, United States

3400 E Britannia Drive, Tucson, Arizona 85706

Tel: [phone] Fax: [phone]

IHB60T REV A 10/01

C&D Technologies, (NCL)

Milton Keynes MK14 5BU UK

T el: [phone] Fax: [phone]

4