Page 1
CRYSTAL CLOCK OSCILLATORS
Data Sheet 0016J
Rev. E
CMOS Compatible Enable/Disable
HA-A1370/A1380 Series
Description
The HA-A1370 Series of quartz crystal oscillators provide enable/disable 3-state CMOS compatible signals
for bus connected systems. Supplying Pin 1 of the HA-A1370 units with a logic “0" enables the output on
Pin 5. Alternately, supplying pin 1 of the HA-A1380 units with a logic “1" enables its Pin 5 output. In the
disabled mode, Pin 5 presents a high impedance to the load. All units are resistance welded in an all metal
package, offering RFI shielding, and are designed to survive standard wave soldering operations without
damage. Insulated standoffs to enhance board cleaning are standard.
Features
• Wide frequency range– 0.5MHz to 20.0MHz
• User specified tolerance available
• Will withstand vapor phase temperatures of 253°C
for 4 minutes maximum
• Space-saving alternative to discrete component
oscillators
• High shock resistance, to 3000g
• All metal, resistance weld, hermetically sealed
package
• 3.3 Volt operation
• Low Jitter
• High Q Crystal actively tuned oscillator circuit
• Power supply decoupling internal
• No internal PLL avoids cascading PLL problems
• Low power consumption
• Gold plated leads - Solder dipped leads available
upon request
Electrical Connection
Pin Connection
1 Enable Input
4 Grd & Case
5 Output
8 V
DD
Dimensions are in inches and (MM)
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: nelsales@nelfc.com
www.nelfc.com
Page 2
CRYSTAL CLOCK OSCILLATORS
Data Sheet 0016J
HA-A1370/A1380 Series Continued
Rev. E
CMOS Compatible - Enable/Disable
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter Symbol Conditions Min Typical Max
Frequency ----- ----- 0.5MHz ----- 20.0MHz
Duty Cycle ----- @ V
Logic 0 VOL @ 600µA ----- ----- 0.2V
Logic 1
Rise & Fall Time tr,tf 10-90% ----- ----- 5 ns
Tpz ----- ----- ----- ----- 25 ns
Enable/Disable
Logic High Voltage ----- ----- 3.0V 2.5V ----Enable/Disable
Logic Low Voltage ----- ----- ----- ----- 0.4V
Jitter, RMS
Frequency Stability
(2)
VOH @ 600µA VDD-0.2V ----- -----
----- ----- ----- ----- 8 psec
(1)
dF/F Overall conditions including: -100ppm ----- +100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
General Characteristics
Parameter Symbol Conditions Min Typical Max
Supply Voltage VDD ----- 2.97V 3.3V 3.63V
Supply Current IDD No Load 0.0 mA ----- 40 mA
Output current IO ----- 0.0 mA ----- ±16.0 mA
Operating temperature TA ----- 0°C ----- 70°C
Storage temperature TS ----- -55°C ----- 125°C
Power Dissipation P
Lead temperature TL Soldering, 10 sec. ----- ----- 300°C
Load ---- ----- ----- ----- 15pf
Start-up time t
D
S
/2 40/60% ----- 60/40%
DD
----- ----- ----- 145 mW
----- ----- 2 ms 10 ms
Environmental and Mechanical Characteristics
Mechanical Shock Per MIL-STD-202, Method 213, Condition E
Thermal Shock Per MIL-STD-833, Method 1011, Condition A
Vibration 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
Soldering Condition 300°C for 10 seconds
Hermetic Seal Leak rate less than 1 x 10 -8 atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) Jitter performance is frequency dependent. Please contact factory for full characterization.
Test Load:
Creating a Part Number
HA - A137X - FREQ
Package Code
HA Leaded 4 pin (8 pin) 0 ±100ppm 0-70°C
SA Leaded 4 pin (8 pin) SMD 1 ±50ppm 0-70°C
Gull Wing 7 ±25ppm 0-70°C
Input Voltage
Code Specification A ±20ppm 0-70°C
A 3.3V B ±50ppm -40 to +85°C
5V C ±100ppm -40 to +85°C
Tolerance/Performance
9 Customer Specific
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: nelsales@nelfc.com
www.nelfc.com
Loading...