Datasheet HA13150A Datasheet (HIT)

HA13150A

21 W × 4-Channel BTL Power IC

ADE-207-107

1st. Edition

Description

HA13150A is a four-channel BTL amplifier IC designed for car audio, featuring high output and low
distortion, and applicable to digital audio equipment. It provides 21 W output per channel, with a 14.4
V power supply and at 10% distortion.

Functions

• Built-in standby circuit

• Built-in muting circuit

• Built-in protection circuits (surge, TSD, and ASO)

Features

• Requires few external parts

• Low distortion (total harmonic distortion = 0.01% at 3 W)

• Low noise (at Rg = 620 Ω, noise is 0.15 mV (muting off) or 0.1 mV (muting on))

• Popping noise minimized

• Highly reliable current-limiting ASO protector keeps speakers safe from all kinds of trouble.

Reliability is further enhanced by a fast-acting thermal shutdown protection circuit with on/off
hysteresis.

HA13150A

Block Diagram

Absolute Maximum Ratings (Ta = 25°C)

Item Symbol Rating Unit Remarks

2

HA13150A

Operating supply voltage V

CC

18 V
Supply voltage when no signal *1VCC (DC) 26 V
Peak supply voltage *
Output current *
Power dissipation *

2

3

4

VCC (PEAK) 50 V
IO (PEAK) 4 A
P

T

83 W
Junction temperature Tj 150 °C
Operating temperature Topr –30 to +85 °C
Storage temperature Tstg –55 to +125 °C

Notes: 1. Tolerance within 30 seconds

2. Tolerance in surge pulse waveform

3. Value per 1 channel

4. Value when attached on the infinite heat sink plate at Ta = 25°C.
The derating carve is as shown in the graph below.

3

HA13150A

Electrical Characteristics (VCC = 13.2 V, f = 1 kHz, RL = 4 Ω, Rg = 620 Ω, Ta =

25°C)

Item Symbol Min Typ Max Unit Test Conditions

Current when no signal Iq1 — 240 — mA Vin = 0
Output offset voltage ∆Vq –250 0 +250 mV
Gain Gv 30.5 32 33.5 dB
Gain difference between

channels
Rated output power Po — 18 — W VCC = 13.2 V

Max output power Pomax — 30 — VCC = 13.7 V

Total harmonic distortion T.H.D — 0.01 — % Po = 3 W
Output noise voltage WBN — 0.15 0.5 mVrms Rg = 0 Ω

Ripple rejection SVR — 55 — dB Rg = 600 Ω

Channel crosstalk C.T — 70 — dB Rg = 600 Ω

Input impedance Rin — 25 — kΩ
Standby current Iq2 — — 200 µA
Standby control voltage

(high)
Standby control voltage

(low)
Muting control voltage

(high)
Muting control voltage

(low)
Muting attenuation A

∆Gv –1.5 0 +1.5 dB

V

STH

V

STL

V

MH

V

ML

TTM

3.5 — V

CC

V

0 — 1.5 V

3.5 — V

CC

V

0 — 1.5 V

— 70 — dB Vout = 0 dBm

RL = 4 Ω, THD = 10%

RL = 4 Ω, THD = Max

BW = 20 to 20 kHz

f = 120 Hz

Vout = 0 dBm

4

Pin Explanation

HA13150A

Pin
No. Symbol Functions

1 IN1 CH1 INPUT 25 kΩ (Typ) 0 V

11 IN2 CH2 INPUT
13 IN3 CH3 INPUT
23 IN4 CH4 INPUT
2 STBY Standby control 90 kΩ

3 OUT1 (+) CH1 OUTPUT — VCC/2

Input
Impedance

(at Trs. cutoff)

DC
Voltage Equivalence Circuit

—

5 OUT1 (–)
7 OUT2 (+) CH2 OUTPUT
9 OUT2 (–)
15 OUT3 (+) CH3 OUTPUT
17 OUT3 (–)
19 OUT4 (+) CH4 OUTPUT
21 OUT4 (–)
10 MUTE Muting control 25 kΩ (Typ) —

5

HA13150A

Pin Explanation (cont)

Pin
No. Symbol Functions

Input
Impedance

DC
Voltage Equivalence Circuit

22 RIPPLE Bias stability — VCC/2

6 PVCC1 Power of output stage — V

CC

—
18 PVCC2
14 INV

CC

Power of input stage — V

CC

—
4 CH1 GND CH1 power GND — — —
8 CH2 GND CH2 power GND
16 CH3 GND CH3 power GND
20 CH4 GND CH4 power GND
12 IN GND Input signal GND — — —

6

HA13150A

Point of Application Board Design

1. Notes on Application board’s pattern design

• For increasing stability, the connected line of VCC and OUTGND is better to be made wider and

lower impedance.

• For increasing stability, it is better to place the capacitor between VCC and GND (0.1 µF) close to

IC.

• For increasing stability, it is better to place C1 to C8 and R1 to R8, which are for stopping

oscillation, close to IC.

• It is better to place the grounding of resistor (Rg), between input line and ground, close to INGND

(Pin 12) because if OUTGND is connected to the line between Rg and INGND, THD will become
worse due to current from OUTGND.

Figure 1 Notes on Application Board’s Pattern Design

7

HA13150A

2. How to reduce the popping noise by Muting circuit

At normal operating circuit, Muting circuit operates at high speed under 1 µs.
In case popping noise becomes a problem, it is possible to reduce the popping noise by connecting

capacitor, which determines the switching time constant, between pin 10 and GND. (Following
figure 2)

We recommend value of capacitor greater then 1 µF.
Also transitional popping noise can be reduced sharply by muting before VCC and Standby are

ON/OFF.

Figure 2 How to use Muting Circuit

Table 1 Muting ON/OFF Time

C (µF) ON Time OFF Time

nothing under 1 µs under 1 µs

0.47 2 ms 2 ms

4.7 19 ms 19 ms

8

HA13150A

9

HA13150A

10

HA13150A

11

HA13150A

12

HA13150A

13

HA13150A

14

HA13150A

When using this document, keep the following in mind:

1. This document may, wholly or partially, be subject to change without notice.

2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or

part of this document without Hitachi’s permission.

3. Hitachi will not be held responsible for any damage to the user that may result from accidents or

any other reasons during operation of the user’s unit according to this document.

4. Circuitry and other examples described herein are meant merely to indicate the characteristics and

performance of Hitachi’s semiconductor products. Hitachi assumes no responsibility for any
intellectual property claims or other problems that may result from applications based on the
examples described herein.

5. No license is granted by implication or otherwise under any patents or other rights of any third party

or Hitachi, Ltd.

6. MEDICAL APPLICATIONS: Hitachi’s products are not authorized for use in MEDICAL

APPLICATIONS without the written consent of the appropriate officer of Hitachi’s sales company.
Such use includes, but is not limited to, use in life support systems. Buyers of Hitachi’s products
are requested to notify the relevant Hitachi sales offices when planning to use the products in
MEDICAL APPLICATIONS.

15