Datasheet 74AC02TTR, 74AC02M, 74AC02B Datasheet (SGS Thomson Microelectronics)

Page 1
74AC02
QUAD 2-INPUT NOR GATE
HIGH SPEED: t
LOW POWER DISSIPATION:
= 2µA(MAX.) at TA=25°C
I
CC
HIGH NOISE IMMUNITY:
V
= V
NIH
50Ω TRANSMISSION LINE DRIVING
= 28 % VCC (MIN.)
NIL
= 4.2ns (TYP.) at VCC = 5V
PD
CAPABILITY
SYMMETRICAL OUTPUT IMPEDANCE:
|I
| = IOL = 24mA (MIN)
OH
BALANCED PROPAGATION DELAYS:
t
t
PLH
OPERATING VOLTAGE RANGE:
V
CC
PIN AND FUNCTION COMPATIBLE WITH
PHL
(OPR) = 2V to 6V
74 SERIES 02
IMPROVED LATCH-UP IMMUNITY
DESCRIPTION
The 74AC02 is an advanced high-speed CMOS QUAD 2-INPUT NOR GATE fabricated with sub-micron silicon gate and double-layer metal wiring C
2
MOS tecnology.
TSSOPDIP SOP
ORDER CODES
PACKAGE TUBE T & R
DIP 74AC02B
SOP 74AC02M 74AC02MTR
TSSOP 74AC02TTR
The internal circuit is composed of 3 stages including buffer output , which enables high noise immunity and stable output. All inputs and outputs are equipped with protection circuits against stat ic discharge, giving them 2KV ESD immunity and transient excess voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
1/8April 2001
Page 2
74AC02
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
PIN No SYMBOL NAME AND FUNCTION
2, 5, 8, 11 1A to 4A Data Inputs 3, 6, 9, 12 1B to 4B Data Inputs
1, 4, 10, 12 1Y to 4Y Data Outputs
7 GND Ground (0V)
14
V
CC
TRUTH TABLE
ABY
LLH
LHL HLL HHL
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
V
V
V
I
I
OK
I
I
or I
CC
T
T
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied.
Supply Voltage
CC
DC Input Voltage -0.5 to VCC + 0.5
I
DC Output Voltage -0.5 to VCC + 0.5
O
DC Input Diode Current
IK
DC Output Diode Current DC Output Current
O
DC VCC or Ground Current
GND
Storage Temperature
stg
Lead Temperature (10 sec)
L
Positive Supply Voltage
-0.5 to +7 V V V
± 20 mA ± 20 mA ± 50 mA
± 200 mA
-65 to +150 °C 300 °C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Value Unit
V
V
V
T
dt/dv
1) VIN from 30 % to 70% of V
2/8
Supply Voltage
CC
Input Voltage 0 to V
I
Output Voltage 0 to V
O
Operating Temperature
op
Input Rise and Fall Time V
CC
= 3.0, 4.5 or 5.5V (note 1)
CC
2 to 6 V
CC CC
-55 to 125 °C 8 ns/V
V V
Page 3
DC SPECIFICATIONS
Test Condition Value
= 25°C
Symbol Parameter
V
CC
(V)
V
V
V
V
I
I
OLD
I
OHD
1) Maxim um test duration 2ms, one output loaded at tim e
2) Incid ent wave switching is guaranteed on transmission l i nes with impe dances as low as 50
High Level Input
IH
Voltage
Low Level Input
IL
Voltage
High Level Output
OH
Voltage
Low Level Output
OL
Voltage
I
Input Leakage
I
Current Quiescent Supply
CC
Current Dynamic Output
Current (note 1, 2)
3.0
5.5 3.85 2.75 3.85 3.85
3.0
5.5 2.75 1.65 1.65 1.65
3.0
4.5
5.5
3.0
4.5
5.5
3.0
4.5
5.5
3.0
4.5
5.5
5.5
5.5
5.5
= 0.1 V or
V
O
V
-0.1V
CC
= 0.1 V or
V
O
V
-0.1V
CC
=-50 µA
I
O
I
=-50 µA
O
I
=-50 µA
O
I
=-12 mA
O
I
=-24 mA
O
I
=-24 mA
O
IO=50 µA I
=50 µA
O
I
=50 µA
O
I
=12 mA
O
I
=24 mA
O
I
=24 mA
O
= VCC or GND
V
I
= VCC or GND
V
I
V
= 1.65 V max
OLD
V
= 3.85 V min
OHD
T
A
Min. Typ. Max. Min. Max. Min. Max.
2.1 1.5 2.1 2.1
1.5 0.9 0.9 0.9
2.9 2.99 2.9 2.9
4.4 4.49 4.4 4.4
5.4 5.49 5.4 5.4
2.56 2.46 2.4
3.86 3.76 3.7
4.86 4.76 4.7
0.002 0.1 0.1 0.1
0.001 0.1 0.1 0.1
0.001 0.1 0.1 0.1
0.36 0.44 0.5
0.36 0.44 0.5
0.36 0.44 0.5
± 0.1 ± 1 ± 1 µA
22040µA
74AC02
-40 to 85°C -55 to 125°C
75 50 mA
-75 -50 mA
Unit
V4.5 3.15 2.25 3.15 3.15
V4.5 2.25 1.35 1.35 1.35
V
V
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 , Input tr = tf = 3ns)
Test Condition Value
T
Symbol Parameter
t
PLH tPHL
(*) Vol tage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ±
Propagation Delay Time
0.5V
V
3.3
5.0
(V)
CC
(*)
(**)
= 25°C
A
Min. Typ. Max. Min. Max. Min. Max.
1.5 5.5 9.5 1.0 10.0 1.0 11.0
1.5 4.2 8.0 1.0 8.5 1.0 8.5
-40 to 85°C -55 to 125°C
Unit
ns
3/8
Page 4
74AC02
CAPACITIVE CHARACTERISTICS
Test Condition Value
T
Symbol Parameter
C
C
Input Capacitance
IN
Power Dissipation
PD
Capacitance
V
CC
(V)
5.0 4 pF
5.0 = 10MHz
f
IN
= 25°C
A
Min. Typ. Max. Min. Max. Min. Max.
46 pF
(note 1)
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I
TEST CIRCUIT
-40 to 85°C -55 to 125°C
= CPD x VCC x fIN + ICC/4 (per gate)
CC(opr)
Unit
CL = 50pF or equivalent (includes jig and probe capacitance) R
= R1 = 500 or equivalent
L
R
= Z
of pulse generator (typically 50)
T
OUT
WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle)
4/8
Page 5
Plastic DIP-14 MECHANICAL DATA
74AC02
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
a1 0.51 0.020
B 1.39 1.65 0.055 0.065 b0.5 0.020
b1 0.25 0.010
D200.787 E8.5 0.335
e2.54 0.100
e3 15.24 0.600
F7.10.280
I5.10.201
L3.3 0.130
Z 1.27 2.54 0.050 0.100
mm inch
P001A
5/8
Page 6
74AC02
SO-14 MECHANICAL DATA
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A1.750.068 a1 0.1 0.2 0.003 0.007 a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C0.5 0.019 c1 45 (typ.)
D 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M0.680.026
S8 (max.)
mm inch
6/8
P013G
Page 7
TSSOP14 MECHANICAL DATA
74AC02
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A1.10.433
A1 0.05 0.10 0.15 0.002 0.004 0.006
A2 0.85 0.9 0.95 0.335 0.354 0.374
b 0.19 0.30 0.0075 0.0118
c 0.09 0.20 0.0035 0.0079
D 4.9 5 5.1 0.193 0.197 0.201
E 6.25 6.4 6.5 0.246 0.252 0.256
E1 4.3 4.4 4.48 0.169 0.173 0.176
e 0.65 BSC 0.0256 BSC
K0
o
o
4
o
8
o
0
o
4
o
8
L 0.50 0.60 0.70 0.020 0.024 0.028
A2
A
A1
PIN 1 IDENTIFICATION
b
e
c
K
L
E
D
E1
1
7/8
Page 8
74AC02
Information furnished is bel ieved to be accurate and reliable. However, STMicroe lectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No li cense is granted by implica tion or otherwise under any patent or patent righ ts of S TMic roelec tronics. Specifications mentioned in this publication ar e subject to change without notice. This publication supersedes and replaces all information previously supplied. S TMicroelectronics products are not authorized for use as critica l components in life suppo rt devices or systems without express written approval of STMicroelectronics.
Australi a - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malay sia - Malta - Morocco
© The ST logo is a registered trademark of STMicroelectronics
© 2001 STM icroelectronics - Prin ted in Italy - All Rights Reserved
STMicr o el ectronics GROU P OF COMPANIE S
Singapo re - Spain - Swe den - Switzerl and - United K i ngdom
© http://www.st.com
8/8
Loading...