Datamax E-Class Mark II Operator's Manual

Operator’s Manual

Basic and Advanced Models

Serial# 3xxxxxxx or earlier

Copyright Information

CG Triumvirate is a trademark of Agfa Corporation. CG Times based upon Times New Roman under license from the Monotype Corporation. Windows is a registered trademark of the Microsoft Corporation. All other brand and product names are trademarks, service marks, registered trademarks, or registered service marks of their respective companies.

Limitation of Liability

In no event shall Datamax-O’Neil be liable to the purchaser for any indirect, special or consequential damages or lost profits arising out of or relating to Datamax-O’Neil’s products, or the performance or a breach thereof, even if Datamax-O’Neil has been advised of the possibility thereof. Datamax-O’Neil’s liability, if any, to the purchaser or to the customer of the purchaser hereunder shall in no event exceed the total amounts paid to DatamaxO’Neil hereunder by the purchaser for a defective product.

In no event shall Datamax-O’Neil be liable to the purchaser for any damages resulting from or related to any failure or delay of Datamax-O’Neil in the delivery or installation of the computer hardware, supplies or software or in the performance of any services.

Some states do not permit the exclusion of incidental or consequential damages, and in those states the foregoing limitations may not apply. The warranties here give you specific legal rights, and you may have other legal rights which vary from state to state.

Firmware (Software) Agreement

The enclosed Firmware (Software) resident in the Printer is owned by Licensor or its suppliers and is licensed for used only on a single printer in the user’s Trade or Business. The User agrees not to, and not to authorize

or permit any other person or party to, duplicate or copy the Firmware or the information contained in the non-volatile or programmable memory. The firmware (Software) is protected by applicable copyright

laws and Licensor retains all rights not expressly granted. In no event will Licensor or its suppliers be liable for any damages or loss, including direct, incidental, economic, special, or consequential damages, arising out of the use or inability to use the Firmware (Software).

Information in this document is subject to change without notice and does not represent a commitment on the part of Datamax-O’Neil Corporation. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser's personal use, without the expressed written permission of Datamax-O’Neil Corporation.

Important Safety Instructions

This printer has been carefully designed to provide years of safe reliable performance. As with all types of electrical equipment, however, there are a few basic precautions that should be taken to avoid personal injury or damage to the device:

• Carefully read the installation and operating instructions provided with the printer.

• Read and follow all warning and instruction labels on the printer.

• Place the printer on a flat, stable surface.

• Do not insert anything into the ventilation slots or openings on the printer.

• Do not place the printer on or near a heat source.

• Do not use the printer near water. Never spill liquid into the printer.

• Be certain the power source is within the voltage rating and frequency listed for the printer. If you are unsure, check with your dealer, an electrician, or local power company.

• Do not place the power cord where it can be stepped on. If the power cord becomes damaged or frayed, replace it immediately.

• Only qualified, trained service technicians should attempt to repair the printer.

Cut-outs are not intended for wall-mount use.

Agency Compliance and Approvals

C US

Listed

FCC: This device complies with FCC CFR 47 Part 15 Class A.

 Note: This equipment has been tested and found to comply with the limits for a Class A digital

UL60950-1, Second Edition, 2007-03-27, Information Technology Equipment CSA C22.2 No. 60950-1-07, Second Edition, 2007-03

The manufacturer declares under sole responsibility that this product conforms to the following standards or other normative documents:

EMC: EN 55022 (2008) Class A EN 50024 (1998) IEC 60950-1 :2001, Second Edition

Safety: This product complies with the requirements of IEC 60950-1:2001, Second Edition

Customs Union – Russia, Kazakhstan, Belarus

GB4943-2001, GB9254-2008, GB17625.1-2012

E-4205A, E-4305A, E-4204B, E-4304B models: The foregoing equipment has been registered under the Clause 3, Article 58-2 of Radio Waves Act

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions in this manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Part Number: 88-2353-01, Revision E

s

t

n

e

t

n

o

C

1

G

1

G

1

G

1.1 Introduction ........................................................................................................ 1

1.2 Unpacking the Printer ........................................................................................... 1

2

P

2

P

2

P

2.1 Introduction ........................................................................................................ 3

2.2 Connecting the Printer .......................................................................................... 3

n

o

n

o

e

t

i

n

e

r

g

t

i

n

g

t

i

n

g

i

n

t

e

r

i

n

t

e

r

i

n

t

e

r

2.2.1

2.2.2 Interface Connections ................................................................................. 4

Cable Requirements .............................................................................................. 4

e

t

e

t

S

t

a

r

t

e

S

t

S

t

S

e

S

e

S

e

Power Connections ..................................................................................... 3

d

a

r

t

e

d

a

r

t

e

t

u

p

.

t

u

p

.

t

u

p

.

n

.

d

.

t

.

s

.

1

.

1

.

1

.

3

.

3

.

3

2.3 Loading Media ...................................................................................................... 5

2.3.1 Loading Roll Media ..................................................................................... 5

2.3.2 Loading External or Fan-Fold Media .............................................................. 7

2.3.3 Loading Media with the Peel and Present Option .............................................. 9

2.3.4 Loading Media with the Cutter Option .......................................................... 10

2.4 Loading Ribbon .................................................................................................. 11

2.4.1 Using the Ribbon Core Adapters ................................................................. 14

3

P

r

i

n

t

e

r

O

p

e

r

a

t

i

o

n

.

3

P

r

i

n

t

e

r

O

p

e

r

a

t

i

o

n

.

3

P

r

i

n

t

e

r

O

p

e

r

a

t

i

o

n

.

3.1 Introduction ...................................................................................................... 15

3.2 LED Indicators ................................................................................................... 15

3.3 Multi-Function Button .......................................................................................... 16

3.4 Printer Configuration Tools .................................................................................. 17

3.5 Printer Configuration Utility (DMXConfig) ............................................................... 18

3.6 Windows Driver .................................................................................................. 20

Important Notes: ............................................................................................... 21

.

1

.

5

.

1

.

5

.

1

5

3.7 Media Calibration ............................................................................................... 22

Calibration ensures correct media detection. .......................................................... 22

3.7.1 Quick Calibration ...................................................................................... 22

3.7.2 Media Calibration Wizard ........................................................................... 23

3.8 Internal Labels ................................................................................................... 25

3.8.1 Database Configuration Label ..................................................................... 25

i

4

M

a

i

n

t

e

n

a

n

c

e

&

A

d

j

u

s

t

m

e

n

t

s

.

4

M

a

i

n

t

e

n

a

n

c

e

&

A

d

j

u

s

t

m

e

n

t

s

.

4

M

a

i

n

t

e

n

a

n

c

e

&

A

d

j

u

s

t

m

e

n

t

s

.

4.1 Introduction ...................................................................................................... 27

4.2 Cleaning the Printhead ........................................................................................ 28

4.3 Ribbon Tension Adjustment ................................................................................. 30

4.4 Adjustable Media Sensor ..................................................................................... 31

4.5 Printhead Replacement ....................................................................................... 32

4.6 Platen Roller Replacement ................................................................................... 34

4.7 Downloading Firmware and Fonts ......................................................................... 35

5

T

r

o

u

b

l

e

s

h

o

t

i

n

g

.

5

T

r

o

u

b

l

e

s

h

o

t

i

n

g

.

5

T

r

o

u

b

l

e

s

h

o

t

i

n

g

.

5.1 Introduction ...................................................................................................... 37

5.2 Troubleshooting Tips ........................................................................................... 37

A

S

p

e

c

i

f

i

c

a

t

i

o

n

s

.

A

S

p

e

c

i

f

i

c

a

t

i

o

n

s

.

S

p

e

c

i

f

i

c

a

t

i

o

n

s

.

2

.

7

.

2

.

7

.

2

7

.

3

7

.

3

7

.

3

7

.

3

9

.

3

9

.

3

9

B

E

t

h

e

r

n

e

t

S

e

t

u

p

.

B

E

t

h

e

r

n

e

t

S

e

t

u

p

.

B

E

t

h

e

r

n

e

t

S

e

t

u

p

.

B.1 Network Card Setup ........................................................................................... 43

B.1.1

B.2 Printer’s Internal Web Pages ................................................................................ 46

B.3 Installing the Printer Driver .................................................................................. 49

G

l

o

s

a

r

G

l

o

l

o

y

s

a

r

y

s

a

r

y

Wired Configuration - Static IP Address ....................................................... 43

.

4

3

.

4

3

.

4

3

.

5

1

.

5

1

.

5

1

ii

d

e

t

r

a

t

S

g

n

i

t

e

G

1

.

1

.

1

.

1

The E-Class Mark III printer (hereafter referred to as “the printer”) is user-friendly thermal printing device that blends quality and durability in an affordable package to meet all of your labeling needs. This manual provides the information necessary to operate and maintain the printer.

To begin printing labels or tags, refer to the instructions included with your software labeling program. For your convenience, a Windows printer driver can be found on the Accessories CD-ROM, or it can be downloaded from our website at http://www.datamax-oneil.com. (If you wish to write custom programs or label formats, a copy of the Class Series 2 Programmer’s Manual also is included for your reference, or the manual can be downloaded.)

1

.

2

1

.

2

1

.

2

I

n

t

r

o

d

u

c

t

k

u

k

u

i

c

t

i

c

t

i

n

g

i

n

g

i

n

g

I

n

t

r

o

n

d

t

r

o

d

p

a

c

p

a

c

p

a

c

I

n

U

n

U

e

o

n

o

n

o

t

n

h

t

e

P

e

P

e

P

t

r

n

i

n

i

n

t

e

r

i

n

i

n

t

e

r

t

e

r

g

S

t

a

r

t

e

d

After removing the printer from the packaging material, check the contents of the box. In addition to the printer, the following items should be present:

 Power Supply  Accessories CD-ROM  Any special or additionally ordered items

Additional Requirements

The following items are necessary to generate labels:

 Parallel, Serial, USB, or (if equipped for LAN

connectivity an Ethernet cable); see Section

2.2.2 for details.

 Applicable media; see Appendix A for

details.

Contact customer support or your sales representative for advice on the media and software that may best be suited for your application.



It is a good idea to save all packaging material for future use.

312

Chapter 1 – Getting Started 1

2 Chapter 1 – Getting Started

p

u

t

e

S

r

e

t

n

i

r

P

r

P

2

.

1

2

.

1

2

.

1

This section explains how to connect your printer and load media (including ribbon, if equi pped for thermal transfer operation).

2

.

2

.

2

.

2

2.2.1 Power Connections

The printer is powered by an external auto-ranging power supply, which connects between the printer and an electrical outlet. Ensure that the operating ranges of the power supply are compatible with your electrical service, (see Appendix A for details) then connect power as follows:

I

C

n

t

n

t

n

t

o

n

o

n

r

o

d

u

c

t

c

u

i

c

t

i

c

t

i

t

i

n

t

i

n

t

i

n

r

o

d

r

o

d

n

e

n

e

n

e

r

o

g

n

t

i

t

n

h

e

t

e

t

P

r

i

n

P

t

r

i

n

t

r

i

n

t

P

e

r

S

e

t

u

p



Before connecting power to the printer, ensure that the Power Switch is in the OFF (O) position.

1) Connect the Power Supply to Power Jack of the printer.

2) Connect the AC Power Cord to the Power Supply.

3) Connect the AC Power Cord to an Electrical Outlet.

312

Power Supply



AC Power Cord



Power Jack



Electrical Outlet



Chapter 2 – Printer Setup 3

2.2.2 Interface Connections

The printer can be connected to the host system via the parallel, serial, Ethernet or USB ports.



Before connecting interface cables to the printer, ensure that the Power Switch is in the OFF (O) position.

312

Cable Requirements

Choose the correct cable when interfacing the printer to the host:

 The Parallel Port (optional) supports parallel communications via a 36-pin male mini-Centronics

connector. Bi-directional communications (forward and reverse channels) is supported when an IEEE 1284 compliant cable and supporting host software is used.

 The Ethernet Port (optional) supports Wired LAN communications (see Appendix B for

information).

 The Serial Port supports RS-232C communications via a DB-9 connector with specific pin-outs

(interface cable part numbers and pin-outs are given below; contact your reseller to order). Serial port settings are menu-selectable and must match the host settings.

   

Ethernet Port USB Port Serial Port Parallel Port

Part # 32-2483-01

 The USB Port supports high-speed serial communications and requires a standard USB interface

cable.

The printer automatically establishes communications with the first port through which valid data is



received. Afterward, a timeout period must be exceeded (or power must be cycled OFF and ON) to change the established communications port.

4 Chapter 2 – Printer Setup

Part # 32-2301-01

2

.

3

L

o

a

d

i

n

g

M

e

d

i

a

2

.

3

2

.

3



L

o

a

d

i

n

g

M

L

o

a

d

i

n

If the printer is equipped with an Adjustable Media Sensor it may require adjustment to match your media choice. If the printer is equipped with this type of sensor, proceed to Section 4.4.

g

M

e

d

i

a

i

a

2.3.1 Loading Roll Media

Load media as follows:

1) Slide the Media Guides outward.

2) Slide the Media Hangers outward and insert the Roll Media as shown. Allow the Media Hangers to retract and grasp the media roll.

312

Media Hangers



Media Guides



Roll Media



3) Pull out enough media to exit the front of the printer. Adjust the Media Guides so they are lightly touching the edge of the media.

312

Chapter 2 – Printer Setup 5

4) If using thermal transfer media (ribbon) proceed to Section 2.4 Loading Ribbon. Otherwise close the printer’s Cover and press downward until latched.

312

Cover





5) Press the

button several times to advance the media (if the Fault Light is lit, see Section 3.7.)

The printer is factory set to use gap media. If using another media type (for example, continuous media), printer setup must be reconfigured; see Section 3.4

.

6 Chapter 2 – Printer Setup

2.3.2 Loading External or Fan-Fold Media

Load media as follows:

1) Slide the Media Guides outward.

2) Slide the Media Hangers outward and install the two Media Chute Guides into the Media Hangers.

Media Chute Guides



Media Hangers



External Media Guide



3) Position the Media Hangers to match the width of the media being used. Slide the Hanger Lock against the Media Hanger to hold this position.

Media Hangers



Hanger Lock



Chapter 2 – Printer Setup 7

4) Route the media through the External Media Slot in the rear of the printer. Pull out enough media to exit the front of the printer. Adjust the Media Guides so they are lightly touching the edge of the media.

External Media Slot



Media Guides



External Media Supply





5) If using Thermal Transfer media (ribbon) proceed to Section 2.4 Loading Ribbon. Otherwise cl ose the printer’s Cover and press downward until latched.

6) Press the button several times to advance the media (if the Fault Light is lit, see Section 3.7.)

The printer is factory set to use gap media. If using another media type (for example, continuous media), printer setup must be reconfigured; see Section 3.4

.

8 Chapter 2 – Printer Setup

2.3.3 Loading Media with the Peel and Present Option

Load media for peeling (if the printer is equipped with the option) as follows:

 

When using the Peel Mechanism do not exceed a print speed of 4 IPS.

To utilize “Tear mode” with Peel and Present Option installed; move the Peeler Door to its open position.

1) Load media as described in Section 2.3, (steps 1-3).

2) Remove about 8 inches (200mm) of labels from the Media Backing.

3) Open the Peeler Door. Route the Media Backing over the Platen Roller and Peel Bar, and then behind the Peel Roller and Peeler Door, as shown below.

312

Media Backing



Peeler Door



Platen Roller



Peel Bar



Peel Roller



4) Close the Peeler Door.

5) If using Thermal Transfer media (ribbon) proceed to Section 2.4 Loading Ribbon. Otherwise cl ose the printer’s Cover and press downward until latched.

button several times to advance the media (if the Fault Light is lit, see Section 3.7.)



6) Press the

7) The printer will now peel each label and present it to the operator for removal. The indicator light will flash orange and the next label will not feed/print until the previous label is removed.

The printer is factory set to use gap media. If using another media type (for example, continuous media), printer setup must be reconfigured; see Section 3.4

Chapter 2 – Printer Setup 9

.

2.3.4 Loading Media with the Cutter Option

Load media for cutting (if the printer is equipped with the option) as follows:

1) Load media as described in Section 2.3, (steps 1-3).

2) Route the media through the opening in the Cutter.

312

Cutter



Media



 

3) If using Thermal Transfer media (ribbon) proceed to Section 2.4 Loading Ribbon. Otherwise cl ose the printer’s Cover and press downward until latched.

4) Press the button several times to advance the media (if the Fault Light is lit, see Section 3.7.). The printer will now cut each label as it exits from the printer.

7) The printer will now peel each label and present it to the operator for removal.

If the printer is equipped with the Present Sensor Option, the indicator light will flash orange and the next label will not feed/print until the previous label is removed.

The printer is factory set to use gap media. If using another media type (for example, continuous media), printer setup must be reconfigured; see Section 3.4

.

10 Chapter 2 – Printer Setup

2

.

4

L

o

a

d

i

n

g

R

i

b

o

n

2

.

4

L

o

a

d

i

n

g

R

i

b

2

.

4

L

o

a

d

i

n

g

The printer is capable of using C.S.I (Coated Side In) and C.S.O (Coated Side Out) ri bbons in the following configurations:

½” Core Ribbons

Ribbon Core Width: 4.3 inches (110mm) Ribbon Width: 1.0 - 4.3 inches (25 - 110mm); Centered on core

1” Core Ribbons (with Ribbon Core Adapters, see section 2.4.1.)

Ribbon Core Width: 1.0 - 4.3 inches (25 - 110mm); Centered on Ribbon Core Adapters

Ribbon Width: 1.0 - 4.3 inches (25 - 110mm); Centered on core

Load ribbon as follows:

If equipped with the thermal transfer option, the printer is factory set to use ribbon; see Section 3.4 to



change this setting if using direct thermal media.

1) Determine the type of ribbon (C.S.I or C.S.O) you are using.

b

R

i

b

o

n

312



Ensure the inked side of the ribbon faces toward the label media, not the printhead.

Chapter 2 – Printer Setup 11

C.S.I Coated Side In Ribbon C.S.O Coated Side Out Ribbon

2) Push out the Supply Hub and load the Supply Roll into the printer as shown. Depending on the size of the Supply Roll, the Media Bouncer may need to be pushed out of the way.

3) Once the Supply Roll is loaded, slide the Ribbon Handler Latch downward to unlatch the Ribbon Handler Assembly.

312

Supply Roll



Supply Hub



Media Bouncer



Ribbon Handler Latch



Ribbon Handler Assembly



4) Push out the Take-up Hub and load an empty Ribbon Core into the printer as shown.

312

Ribbon Core



Take-up Hub



12 Chapter 2 – Printer Setup

5) Route the ribbon from the supply roll to the Ribbon Core, as shown below.

6) If not already attached, affix the leader of the ribbon to the Ribbon Core using Tape. Rotate the Take-up Hub Wheel several times to secure the ribbon.

312

Ribbon Core



Tape



Take-up Hub Wheel



7) Raise and latch the Ribbon Handler Assembly. Close the cover and press the

button several

times to advance the media (if the Fault Light is lit, see Section 3.7. )

312

Ribbon Handler Assembly



Cover



Chapter 2 – Printer Setup 13

2.4.1 Using the Ribbon Core Adapters

When using ribbons with a 1” (25.4mm) I.D. core, a Core Adapter must be used.

1) Slide the Ribbon Roll (with the leader positioned as shown above) onto a Core Adapter. Slide an empty Ribbon Core onto the remaining Core Adapter.

312

  

Core Adapter Ribbon Roll Ribbon Core

2) If using a narrow ribbon, position the Ribbon Roll so that it is centered on the Core Adapter. The Core Adapters are marked in both inches and centimeters to aid in proper positioning.

Core Adapter



Ribbon Roll



312

14 Chapter 2 – Printer Setup

n

o

i

t

a

r

e

O

p

e

r

a

t

i

t

Green/Orange Status LED



Red Error LED



Multi-function Button



o

n

o

i

P

r

P

3

.

1

3

.

1

3

.

1

The Front Panel consists of two indicator lights and one multi-function button, as detailed in the following sections.

I

n

t

r

o

d

u

c

t

I

n

t

r

o

I

n

d

t

r

o

d

u

c

i

t

i

t

i

r

o

n

i

n

t

312

e

r

O

r

e

t

n

i

r

s

LED 1 LED 2

Paused or Present Sensor is blocked.

No power

TOF sensing error. Next TOF not Found.

Red

No Error

3

.

2

L

E

D

I

n

d

i

c

a

t

o

r

3

.

2

L

E

D

I

n

d

i

c

3

.

2

L

E

D

I

n

Two LED indicator lights provide a quick visual reference of printer operations and conditions, as defined below:

Color Green Orange

Solid

Flashing

Off



Both indicators will be ON during power-up initialization and following a reset.

a

d

i

c

a

Ready to print

Processing/busy Paused/busy Out of stock\labels or printer jam..

s

t

o

r

s

t

o

r

Chapter 3 – Printer Operation 15

3

.

3

M

u

l

t

i

-

F

u

n

c

t

i

o

n

B

u

t

o

n

3

.

3

M

u

l

t

i

-

F

u

n

c

t

i

o

n

B

u

3

.

3

M

u

l

t

i

-

F

u

n

c

t

i

o

n

The multi-function button perform different functions depending upon the mode of the printer:

Button Action

Momentary Press

Press and hold for 5

seconds (release when

LED blinks orange)

Press and hold for 10

seconds (release when

LED blinks green)

Press and hold for 15

seconds (release when

LED blinks red)

Press and hold for 20

*Dealer Settings can b e d efin ed an d mo difie d us ing the DM XConfig pr inte r c onf igu rat ion u tility, s ee se ct ion 3 .5

seconds

LED 1 – Green

Ready/Idle

Printer feeds media to

the next label.

Prints Network Report

Performs the Quick

Media Calibration

Resets the printer’s

parameters to the

stored Dealer Settings*

t

B

u

t

Label

Performs a ‘warm reset’. Does not effect any stored printer settings.

t

o

n

t

o

n

LED 1 – Green

Printing

Pauses Printer Resumes printing Clears Fault

Cancel Batch Cancel Batch

LED 1 – Orange

Paused

Performs the Quick

Media Calibration

Resets the printer’s

parameters to the

stored Dealer Settings*

LED 2 – Red

Faulted

Performs the Quick

Media Calibration

Resets the printer’s

parameters to the

stored Dealer Settings*

16 Chapter 3 – Printer Operation

3

.

4

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

a

t

i

o

n

T

o

l

s

3

.

4

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

a

t

i

o

n

T

3

.

4

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

a

t

i

o

The printer contains many user adjustable parameters. These parameters are configurable using a few methods. The table below lists the most popular ways of configuring the printer and the advantages of each. Choose the method that best addresses your application.

Method Description Pros Cons For More Info

DMXConfig (located on the Accessories CD-ROM) is a Windows based configuration

DMXConfig Program*

Internal Web Pages*

utility that allows the user to make changes to the existing printer setup via a direct connection to the host computer’s serial, USB, or parallel connection.

Internal web pages are simple HTML pages that can be accessed with any web browser via the optional Ethernet port.

n

o

T

o

l

s

o

l

s

Easy to use, gives the user the most control of the printer.

Easy to use. Printer can be configured from any host connected to the network regardless of physical location or host operating system.

No additional software required.

Software must be installed on a Windows based host computer.

Printer must be equipped with an Ethernet option.

Depending on the complexity of the network, initial connection may not be possible until network parameters are set via another method.

See

Section 3.5

See

Appendix B.2

Windows Driver

DPL Programming Commands

* Recommended methods

The Windows printer driver (located on the Accessories CDROM).

DPL Programming Language commands can be built into custom label formats or sent individually to the printer.

Many applications require use of driver for printing from 3 party applications. This can be an all in one solution for some users that do not require advanced setups.

DPL commands can be built directly into label formats which can configure the printer on the fly.

rd

Requires installation of a driver on a Windows based host.

Only basics parameters can be configured.

DPL programming knowledge needed.

See

Section 3.6

See the

Class Series 2 Programmer’s

Manual

Chapter 3 – Printer Operation 17

3

.

5

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

a

t

i

o

n

U

t

3

.

5

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

a

t

i

o

3

.

5

P

r

i

n

t

e

r

C

o

n

f

i

g

u

r

DMXConfig (located on the Accessories CD-ROM) is a Windows-based configuration utility that allows the user to make changes to the existing printer setup via a direct connection to the host computer’s serial, USB, or parallel ports.

DMXConfig Features:

 Allows Real-Time Control/Query of Printer Configuration  Define and Save Optimal Configurations for Applications  Saved Configurations can be Shared with other Printers and Sent via Email  Download Files, Formats and Fonts  Query Memory Modules

Be sure to use the DMXConfig utility located on the Accessories CD-ROM that is included with your



A new feature of DMXConfig allows the use of Datamax-O’Neil Windows Driver for bidirectional communications and configuration. Before this feature can be used, a small setting change must be made to the printer driver’s properties.

Right-click on the printer driver icon and select Properties. Click on the Advanced Tab and select "Print directly to the printer", then click OK.

printer. Older versions might not operate correctly with some printers. For the latest version please visit our web site at http://www.datamax-oneil.com

a

n

t

i

o

n

i

U

t

i

U

t

i

(

D

M

X

C

o

n

f

i

g

)

l

i

t

y

(

D

M

X

C

o

l

i

t

y

(

D

M

l

i

t

y

X

C

o

n

f

i

g

)

f

i

g

)

18 Chapter 3 – Printer Operation

Once you have installed the DMXConfig utility:

1) Connect the host to the printer with a serial, parallel, or (USB cable if driver is installed).

2) Turn ON the printer and launch the DMXConfig utility.

3) Click on the port or the printer you wish to connect to from the list.

4) Query the printer by using the Query Printer toolbar button (top-left) or the large ‘Query’ button in the green box. This will connect to the printer and get the current printer settings.

5) At this point you may browse the tabs and make any changes necessary to the printer configuration. Once complete, send the new settings to the printer using the Configure Printer toolbar button.

(The example below illustrates changing the Media Type setting to Thermal Transfer. Other parameters can be changed using this procedure as well.)

6) Select the Media Settings tab then in the Media Type drop-down box select Thermal Transfer.

7) Send the settings to the printer using the Configure Printer toolbar button.

The printer is now configured to use thermal transfer media. You may close the DMXConfig utility and begin printing using ribbon.

Chapter 3 – Printer Operation 19

3

.

6

W

i

n

d

o

w

s

D

r

i

v

e

r

3

.

6

W

i

n

d

o

w

s

D

r

3

.

6

W

i

n

d

o

w

s

The Windows driver is located on the Accessories CD-ROM included with your printer. For the latest version please visit our web site at http://www.datamax-oneil.com

Installing the Windows Driver:

1) Place the Accessories CD-ROM included with your

printer into your computers CD-ROM drive.

2) Once the CD-ROM starts select your printer model then

“Install Driver” from the menu and follow the instructions on the screen to install.

3) When prompted, select your pri nter from the list, (i.e.

Datamax-O’Neil E-4xxx Mark III). Continue to follow the on-screen instructions to install the driver.

i

D

r

v

e

r

i

v

e

r

20 Chapter 3 – Printer Operation

Important Notes:

The Windows driver functions the same as any other Windows printer. While built-in help files provide information on all settings, there are some important setting parameters that should be observed for trouble free printing:

Page Setup Tab: Stock

It is important that the Stock setting matches the size of the label you are using. If you cannot find a match for your label click New and enter the dimensions of your label.

Options Tab: Print Speed & Printhead Temperature

These two settings will have the greatest effect on print quality. Some label stocks will require more heat and slower print speeds to generate a quality image.

The Windows application software used to create the label format will likely have a "Page Setup" screen. This will also need to match the size of the label you are using.

Chapter 3 – Printer Operation 21

3

.

7

M

e

d

i

a

C

a

l

i

b

r

a

t

i

o

n

3

.

7

M

e

d

i

a

C

a

l

i

b

r

3

.

7

M

e

d

i

a

C

a

Calibration ensures correct media detection.

a

l

i

b

r

a

t

i

o

n

t

i

o

n

3.7.1 Quick Calibration

The Quick Calibration can be performed using the DMXConfig Utility (see Section 3.5) or by holding down the multi-function button, (see section 3.3) . Once you have installed the DMXConfig utility and the printer is properly loaded with media, proceed with calibration as follows:

 This calibration is not necessary when using continuous stock.



1) Connect the host to the printer with a serial,

2) Turn ON the printer and launch the

3) Click on the port or the printer you wish to

4) Query the printer by using the Query Printer

5) Select the Sensor Calibration Tab and then

6) Wait for the printer to process the data. There

 Media containing large gaps may require a change in the Paper Out Distance before proceeding.

parallel, or (USB cable if driver is installed).

DMXConfig utility.

connect to from the list.

toolbar button (top-left) or the large ‘Query’ button in the green box. This will connect to the printer and get the current printer settings.

click the Quick Media Calibration button. When prompted click OK to start the Quick Calibration.

are two possible outcomes: Green Light = Successful calibration Red Light = Unsuccessful calibration, try

again. If the calibration continues to fail, proceed to Section 3.7.2.

22 Chapter 3 – Printer Operation

3.7.2 Media Calibration Wizard

The Media Calibration Wizard can be performed using the DMXConfig Utility (see Section 3.5). Once you have installed the DMXConfig utility and the printer is properly loaded with media, proceed with calibration as follows:

1) Connect the host to the printer with a serial, parallel, or (USB cable if driver is installed).

2) Turn ON the printer and launch the DMXConfig utility.

3) Click on the port or the printer you wish to connect to from the list.

4) Query the printer by using the Query Printer toolbar button (top-left) or the large ‘Query’ button in the green box. This will connect to the printer and get the current printer settings.

5) Select the Sensor Calibration Tab and then click the Media Calibration Wizard button. When prompted click OK to start the calibration wizard.

6) The Calibration Wizard will now prompt you to Remove Stock. Remove media and backing from the printer. Close the cover and click OK.

Chapter 3 – Printer Operation 23

7) The Calibration Wizard will now prompt you to Load Backing. Peel off a few labels and position the backing material over the media sensor. Close the cover and click OK.

6) The Calibration Wizard will now prompt you to Load Stock. Ensure that media is properly loaded in the printer then close the cover and click OK.

9) The Calibration Wizard will now respond with Passed Calibration and green light on the

printer; click OK. Each press of the should advance one label.

If the calibration was unsuccessful, retry the procedure beginning at Step 5.

button

24 Chapter 3 – Printer Operation

3

.

8

I

n

t

e

r

n

a

l

L

a

b

e

l

s

3

.

8

I

n

t

e

r

n

a

l

L

a

3

.

8

I

n

t

e

r

n

a

The following section details the resident information and test labels.

3.8.1 Database Configuration Label

The Database Configuration Label provides information including the printer firmware version, memory allocations, enabled options, and label-counter data.

Print a Database Configuration Label as follows:

1) Load with media (4 inch wide) and ribbon (if printing with thermal transfer media).

2) Turn the printer on. Both LEDs will be on.

3) When the right LED turns off, press and hold the button until the Database Configuration Label begins to print.

b

l

L

a

b

e

l

s

l

s

(Printed label may not match the label shown above.)

Chapter 3 – Printer Operation 25

26 Chapter 3 – Printer Operation

&

e

c

n

a

n

e

t

n

i

A

c

t

c

t

c

t

a

i

a

i

a

d

i

o

n

i

o

n

i

o

n

Turn OFF the printer before cleaning the printhead. Use solvent* applied with a cotton swab to clean the printhead from end to end.

Turn OFF the printer. Rotate the platen roller and clean it thoroughly with solvent* applied with a cotton swab.

Rotate the peel-off roller and clean it thoroughly with solvent* applied with a cotton swab.

n

u

j

u

j

u

j

t

e

s

n

t

m

a

n

e

n

c

n

&

e

s

t

s

t

s

t

After every roll of media.

M

4

.

1

4

.

1

4

.

1

This section details the cleaning, adjusting, and troubleshooting tips for the printer. The following table outlines the recommended maintenance schedule for the various printer parts.

I

n

I

n

I

n

Printhead

Platen Roller

Peel-Off Roller

t

r

o

d

t

u

r

o

d

u

r

o

d

u

Area Method Interval

Media Path Solvent* After every roll of media.

Peel/Tear Bar Solvent* As needed

Media Sensor Blown air or brush Monthly

Exterior Mild detergent or desktop cleaner. As needed

Interior Brush or vacuum cleaner As needed.

* A solvent containing isopropyl alcohol is recommended for use.

Isopropyl alcohol is a flammable solvent; always take the proper precautions when in use.

Chapter 4 – Maintenance and Adjustments 27

4

.

2

C

l

e

a

n

i

n

g

t

h

e

P

r

i

n

t

h

e

a

d

4

.

2

C

l

e

a

n

i

n

g

t

h

e

P

r

i

n

t

4

.

2

C

l

e

a

n

i

n

g

t

h

e

P

Never use a sharp, hard, or abrasive object on the printhead.

If print quality declines (symptoms can include unreadable bar codes or streaks through text and graphics), the typical cause is debris buildup on the printhead which, left unattended, can lead to premature dot failure. Depending upon the supplies and printing parameters used, different cleaning methods are recommended.

h

r

i

n

t

h

e

a

d



Proper cleaning is critical. To maintain peak performance of the printer, Datamax-O’Neil offers a complete line of cleaning products including pens, cards, films and swabs. To learn more visit our website.

Cotton Swab Procedure

If printing with direct thermal media or thermal transfer media with wax ribbon, clean the pri nthead as follows:

1) Turn OFF the power switch and unplug the printer. Open the printer. Wait briefly for the printhead to cool.

2) Remove any installed media and ribbon. Using a Cotton Swab moistened (not soaked) with isopropyl alcohol, thoroughly clean the Printhead.

312

Streaks can indicate a dirty or a faulty printhead.

28 Chapter 4 – Maintenance Adjustments

Cotton Swab with Solvent



Printhead



Cleaning Card Procedure

If printing with direct thermal media, thermal transfer media with wax/resin ribbon combinations, or if the Cotton Swab technique was not successful, clean the printhead as follows:

1) Open the printer. Wait briefly for the Printhead to cool.

2) Remove media and ribbon then place a Cleaning Card under the Printhead (part number 70-2013-

01).

3) Close the cover then press the Button to initiate cleaning.

4) After the cleaning card has been run through the printer, reinstall media (and ribbon, if needed). Plug in and turn ON the printer. Run a few sample labels and examine them. If streaking is still present, use the Cleaning Film Procedure, below; otherwise, this completes cleaning.

Cleaning Film Procedure

If printing with thermal transfer media and resin ribbon, when printing with a Heat Val ue of 22 or higher, or when other methods prove unsuccessful, clean the printhead as follows:

1) Open the printer. Wait briefly for the Printhead to cool..

2) Remove media and ribbon then place a sheet of Cleaning Film under the Printhead (part number 70-2087-01).

3) Close the cover then press

4) After the cleaning film has been run through the printer, turn OFF the Power Switch and unplug the printer. Open the cover and wait briefly for the Printhead to cool. Using a cotton swab moistened (not soaked) with isopropyl alcohol, clean the Printhead then allow it to dry.

5) Reinstall media (and ribbon, if needed). Plug in and turn ON the printer. Run a few sample labels and examine them. If streaking is still present, the Printhead may need to be replaced; see Section 4.2

Button to initiate cleaning.

Chapter 4 – Maintenance and Adjustments 29

4

.

3

R

i

b

o

n

T

e

n

s

i

o

n

A

d

j

u

s

t

m

e

n

t

4

.

3

R

i

b

o

n

T

e

n

s

i

o

n

A

d

j

u

s

t

4

.

3

R

i

b

o

n

T

e

n

s

i

o

n

A

d

The adjustable ribbon handler feature, found on printers equipped with the thermal transfer option, allows the optimum amount tension to be supplied by the ribbon supply hub. Adjust the ribbon tension as follows:

1) Turn ‘off’ the printer.

2) Hold the ribbon/ribbon hub to prevent it from turning. Then push in and rotate the Ribbon Tension Adjustment Knob to the position that matches the core size of the ribbon in use.

312

m

j

u

s

t

m

e

n

t

Ribbon Handler



Ribbon Tension Adjustment Knob



30 Chapter 4 – Maintenance Adjustments

4

.

4

A

d

j

u

s

t

a

b

l

e

M

e

d

i

a

S

e

n

s

o

r

4

.

4

A

d

j

u

s

t

a

b

l

e

M

e

d

i

a

S

e

4

.

4

A

d

j

u

s

t

a

b

l

e

M

e

d

i

a

The optional Adjustable Media Sensor (AMS) allows the printer to accept a wider variety of media configurations. The table below defines general AMS positions for various media and Top of Form (TOF) types.

Media Type

Continuous

Die-Cut

Notched

Reflective

Position the AMS as follows:

1) On the Bottom AMS Sensor, identify the proper Indicator for use with your media.

Gap or Notch Indicator



Reflective (Mark) Indicator



Lock Release

2) Depress the Lock Release and slide the Bottom AMS sensor so the Indicator is in line with the center of the notch, gap, or reflective (mark) of the installed media.

3) Depress the Lock Release and slide the Top AMS Sensor over to the same setting as the Bottom AMS Sensor, (this is not necessary if using reflective media).



n

S

e

n

312

s

o

r

s

o

r

AMS Positioning

Sensor Location TOF Sensing Method

Center of the Media Continuous

Center of the Label

Center of the Notch

Center of the Mark Reflective

Gap

4) Load media, see Section 2.3.

Chapter 4 – Maintenance and Adjustments 31

Bottom AMS Sensor



Top AMS Sensor



4

.

5

P

r

i

n

t

h

e

a

d

R

e

p

l

a

c

e

m

e

n

t

4

.

5

P

r

i

n

t

h

e

a

d

R

e

p

l

a

c

e

4

.

5

P

r

i

n

t

h

e

a

d

R

e

p

l

If the Printhead becomes damaged or worn, replace it as follows:

a

c

e

m

e

n

t



Always follow proper Electro Static Discharge procedures when replacing the printhead.

1) Turn OFF the printer and remove the ribbon if installed.

2) Lower the Ribbon Handler Assembly.

3) Press outward on the two Printhead Carrier Tabs and rotate the Printhead Carrier down.

312

Ribbon Handler



Printhead Assembly Tabs



Printhead Carrier



4) Press inward on the two Printhead Shield Tabs and rotate the Printhead Shield down.

312

Printhead Shield Tabs



32 Chapter 4 – Maintenance Adjustments

5) Loosen the Printhead Screw and allow the Printhead to fall free.

6) Remove the Printhead Cable.

312

Printhead Shield



Printhead Screw



Printhead



Printhead Cable



Sensor



Installation:

1) Carefully connect the Printhead Cable to the new Printhead.

2) Position the Printhead in the Printhead Carrier and tighten the Printhead Screw.

3) Ensure the Sensor properly seated and rotate the Printhead Shield upward until it snaps into place.

4) Rotate the Printhead Carrier upward until it snaps into place.

Chapter 4 – Maintenance and Adjustments 33

4

.

6

P

l

a

t

e

n

R

o

l

e

r

R

e

p

l

a

c

e

m

e

n

t

4

.

6

P

l

a

t

e

n

R

o

l

e

r

R

e

p

l

a

c

e

4

.

6

P

l

a

t

e

n

R

o

l

e

r

R

e

p

l

The Platen Roller can be easily removed for cleaning, replacement, or clearing media jams.

1) Turn OFF the printer and remove the media if installed.

2) Lift up on the two Platen Roller Tabs.

312

a

c

e

m

e

n

t

Platen Roller T abs



3) Remove the Platen Roller Assembly from the printer.

Installation:

1) Position the Platen Roller Assembly into the printer.

2) Rotate the two Platen Roller Tabs downward until they snap into place.

312

Platen Roller Assembly



34 Chapter 4 – Maintenance Adjustments

4

.

7

D

o

w

n

l

o

a

d

i

n

g

F

i

r

m

w

a

r

e

a

n

d

F

4

.

7

D

o

w

n

l

o

a

d

i

n

g

F

i

r

m

w

a

r

e

a

4

.

7

D

o

w

n

l

o

a

d

i

n

g

F

i

r

m

w

a

The operating programs and fonts for the printer are stored in Flash memory on the Main PCB. When program updates and/or new features are added, they can be downloaded to the printer as follows:

1. Identify the new version for your model of printer from the Datamax-O’Neil FTP site at ftp.datamaxoneil.com and download it onto your computer’s hard drive or a floppy disk.

2. Ensure that the printer is connected to the host and that the power is ON. Using the DOS copy command, enter:

Other programs (e.g., hyper-terminal and certain Windows Driver programs) may also be used to download



3. The Green LED will flash during the download.

4. Following a successful download, the printer will reset. The previous printer setup will be unaffected

this file.

unless substantial firmware data structure changes have occurred. Print a Database Configuration Label to verify your new firmware version.

Following an unsuccessful download, the RED LED will turn on, then the printer will reset. The original firmware will remain operational. If the printer fails to reset, cycle power OFF and ON.

Try re-sending the file to the printer. If the failure continues, check the following possible causes:

 An invalid or corrupted file is being downloaded - Ensure the file being downloaded is correct and

applicable for your printer model.

 Possible communications error - Check the cable connection between the host and printer and

ensure that a quality, shielded cable is used.

 Possible Flash memory problem - Call for service.

copy filename.zg lpt1/b

n

r

e

a

n

d

o

F

o

F

o

n

t

s

t

s

Chapter 4 – Maintenance and Adjustments 35

36 Chapter 4 – Maintenance Adjustments

g

n

i

t

o

h

s

e

l

b

u

o

r

T

5

.

1

5

.

1

5

.

1

Occasionally, situations arise that require troubleshooting. Possible problem situations and potential solutions are listed below. Contact a qualified technician for problems that persist or problems not covered in this section.

5

.

2

5

.

2

5

.

2

The following section lists the symptoms and the associated page numbers of the topics covered. While not every situation is addressed, you may find some tips helpful. After a correction action is taken press the FEED Button to clear the alarm.

Unacceptable print quality:

The printer does not print or prints several labels at once:

The ribbon does not advance (the paper advances, but ribbon does not):

I

n

t

r

o

d

u

I

n

t

r

I

n

t

r

T

r

o

u

T

r

o

u

T

r

o

u

 Dirty printhead: Clean the printhead (see Section 4.2).  The temperature setting may be incorrect for the media being used: Use the software program or

DPL commands adjust the Heat Setting and Print Speed.

 A mismatched incorrect ribbon/media combination is being used: Check the types being used.  Faulty printhead: Replace it (see Section 4.5) or call for service.

 The labels are incorrectly loaded: See the loading instructions on the inside cover of the printer, or

in Section 2.3.

 The media is not calibrated: Calibrate it (see Section 3.7).  The media sensor or sensor circuitry may be defective: Call for service.

 The ribbon may be installed incorrectly: Ensure that the inked side of the ribbon faces the labels.

With most ribbons this can be verified by rubbing paper against the ribbon; the ink should smudge the paper. Or, if using label stock, the sticky side of a label will pull off the ink.

 A mismatched ribbon/paper combination is resulting in an insufficient amount of friction between

paper and ribbon: Ensure that the correct type of ribbon is being used with the media.

o

b

d

c

u

c

u

c

l

e

s

l

e

s

l

e

s

t

h

t

h

r

i

o

i

o

i

o

n

o

t

o

t

o

t

i

n

i

n

i

n

u

g

T

g

T

g

T

b

i

p

i

p

i

p

s

l

e

s

h

o

t

i

n

g

Chapter 5 – Troubleshooting 37

Skips every other label (print quality is good, but every other label is skipped):

 The label is formatted too close to the top edge of the label: Leave white space equal to 8-dot

rows (about .02 inch [.5mm]) at the top of the label.

 The media is not calibrated: Calibrate it (see Section 3.7 or 3.3).  The media sensor or media sensor circuitry may be defective: Call for service.

Unable to print rotations:

 The characters are formatted outside the dimensi o ns of the label: Check that the row/column

values provide enough room for the height of the image being printed.

Light print on the right side of the label:

 The printer’s cover is not latched down: Latch it.  The printhead is not properly aligned: Call for service.

Printer fails to power ON:

Label advances 1-2 inches before a fault indication:

Label advances 12 inches before a fault indication:

Labels move excessively from side to side during printing:

 The AC wall outlet may be faulty: Try another outlet.  The power supply may be faulty: Replace it.  Possible defective power switch: Call for service.

 The ribbon may be incorrectly installed. Ensure that the inked side of the ribbon faces the labels.

With most ribbons this can be verified by rubbing paper against the ribbon; the ink should smudge the paper. Or, if using label stock, the sticky side of a label will pull off the ink.

 A mismatched ribbon/paper combination is resulting in an insufficient amount of friction between

paper and ribbon: Ensure that the correct type of ribbon is being used with the media.

 The media may not be properly loaded: Reload it (see Section 2.3). When loading media ensure

that the media hangers and media guides are against the media and that gaps or marks in the labels are in line with the media sensor.

 The media sensor or media sensor circuitry may be defective: Call for service.

 The media may not be properly loaded: Reload it (see Section 2.3). When loading media ensure

that the media hangers and media guides are against the media and that gaps or marks in the labels are in line with the media sensor.

38 Chapter 5 – Troubleshooting

A

c

i

f

i

c

e

p

S

p

e

c

i

f

i

c

A

Mechanical

Width 8.01 inches (20.4 cm) Depth 11.10 inches (28.2 cm) Height 7.36 inches (18.7 cm) Weight 5.25 pounds (2.4 kg)

a

t

i

o

n

s

Operating Temperature AC Input Voltage Power Supply

Printing

Print Method Direct Thermal; Thermal Transfer (optional)

Print Speed

Resolution

Tear Bar Tear up DRAM Memory 16MB FLASH Memory 64MB

40 to 95 F (4 to 35 C)

105 VAC to 250 VAC / 50-60 Hz

Basic Models: 2 - 4 IPS (50.8 - 101mm/s) Advanced Models: 2 - 5 IPS (50.8 – 127mm/s)

203 DPI Models: 203 DPI (8 dots/mm) 300 DPI Models: 300 DPI (11.8 dots/mm)

Appendix A – Specifications 39

Media / Ribbon

Media Types Roll-Fed, Die-Cut, Continuous, Fan-Fold Max. Media Width 4.4 inches (110mm) Min. Media Width 0.75 inches (19mm)

Max. Print Width

203 DPI Models: 4.25 inches (108mm) 300 DPI Models: 4.12 inches (106mm)

Print Length Range .236 – 99 inches (6 - 2514mm)

Tear: 0.5 inches (12mm)

Minimum Label Height

Peel: 1.0 inches (25mm) Cut: 1.18 inches (30mm)

Media Thickness Range

.0025 - .01 inches (.064 - .254mm); up to .005 inches (.127mm) with

optional Cutter

Media Supply Roll Capacity 5 inches (127mm) O.D. on a 1 inch (25.4mm) core

½” Core Ribbons Ribbon Core Width: 4.3 inches (110mm) Ribbon Width: 1.0 - 4.3 inches (25 - 110mm); Centered on core

Ribbon Width Range

1” Core Ribbons (with Ribbon Core Adapters, see section 2.4.1.) Ribbon Core Width: 1.0 - 4. 3 inches (25 - 110mm); Centered on Ribbon Core Adapters

Ribbon Width: 1.0 - 4.3 inches (25 - 110mm); Centered on core

Ribbon Roll Capacity

0.5” (13mm) core with 361’ (110m) long ribbon or 1" (25mm) core with 984' (300m) long ribbon

Communications

Interface Ports (standard) Baud Speed 600 to 38,400 bits per second (BPS)

USB, RS-232 (DB-9), & IEEE 1284 Type C compliant mini-Centronics parallel

Handshaking Xon/Xoff, CTS, DTR Parity Even, Odd, or None Stop Bits 1 or 2 Data Bits 7 or 8

Fonts

9 Bit Mapped Fonts rotated 0, 90, 180, and 270 degrees.

Embedded Bar Codes

32 embedded barcodes (see the Class Series 2 Programmer’s Manual for a detailed listing).

40 Appendix A – Specifications

Approved Media

To achieve optimum print quality and maximum printhead life, Datamax-O’Neil specifies the use of DatamaxO’Neil brand media and ribbons. These supplies are specially formulated for use in our printers; use of other supplies may affect the print quality, performance, and life of the printer or its components. For a current list of approved media and ribbons for use in direct thermal and thermal transfer applications, please contact a Media Representative at (407) 523-5650.

G

I

H

F

J

D

E

A B

A Label width B Backing width 4.4 .75

C Gap between labels .25 .10 D Label length 24 E Total thickness .010

F Notch opening width -- .20

Distance from the center of the media to

G

the center of media sensor aperture

with the Adjustable Media Sensor option

H Reflective mark width

I Distance between reflective marks 24 J Reflective mark length .25 .10

[1]

Units of measure are in inches.

[2]

The reflective (black) mark must be carbon based, placed on the backside of the

stock, and the reflectance shall be less than 10% at wavelengths of 950 and 640 nm.

[3]

The label length may vary up to 99 inches with printable area not exceeding the maximum label length.

[4]

This distance is inclusive of the minimum gap between labels. Min length of 1.25 inches (31.8mm) with optional Cutter installed.

[5]

This distance is inclusive of the minimum reflective mark.

[6]

.007 inches (.117mm) w/Standard Cutter.

Description Max

203 DPI: 4.25 300 DPI: 4.12

[2]

4.4 .50

[1]

[3]

.25

[6]

.0025

.1875 --

Adjustable across full media width

[3]

.25

C

Min

.75

[1]

[4]

[5]

Appendix A – Specifications 41

42 Appendix A – Specifications

p

u

t

e

S

t

e

n

r

e

h

t

E

B

.

1

B

.

1

B

.

1

The Print Server makes IP requests at power-up, so before making a network connection to the printer consider how your IP addressing needs to be assigned. The IP addressing of the Internal Ethernet Print Server can be configured in one of two ways: Using a static IP Address or Using IP Discovery (DHCP, BootP, or RARP). At factory default settings, IP DISCOVERY is enabled.

1) With Printer Off, connect the network cable then turn ON Printer.

2) The printer will now search for a DHCP s erver. Allow up to 90 sec onds for the printer t o retrieve a n IP addr ess.

3) At this point it is recommended to print a Ne twork Repo rt. This Ne twork

Press and hold the

4) Verify the printer has obtained a valid IP address for your network. If a

Once the previous steps have been successfully completed you may now use the IP Address to: > Install a printer driver, and start p rinting from you r Wind ows applications; see Se ctio n B.3.

-or-

> Browse to the internal web pages for advanced configuration; see Section B.2.

N

e

t

w

o

r

N

e

t

N

e

t

Report is generated by the printer and lists important default information such as the IP and MAC Addresses. To print the Network Report:

orange).

valid IP address was not obtained or you wish to use a different static address, see Section B.1.1.

w

o

k

r

k

r

k

h

t

h

t

C

a

r

d

C

a

r

d

a

r

d

button for 5 seconds (release when LED blinks

e

S

e

S

e

S

e

t

r

u

p

n

e

t

S

e

t

u

p

The information of this label will vary depending on your configuration and firmware version.

Appendix B – Ethernet Setup 43

B.1.1 Wired Configuration - Static IP Address:

DMXConfig (located on the Accessories CD-ROM) is a Windows based configuration utility that allows the user to make changes to the existing printer setup via a direct connection to the host computers serial and parallel connection. This is a vital tool for the use and configuration of wired and wireless printer setup.



Note: The following example uses the DMXConfig software utility to configure the printer.

1) Connect the host to the printer with a serial, parallel, or (USB cable if driver is installed). Also connect the network cable to the rear of the printer.

2) Turn ON the printer and launch the DMXConfig utility.

3) Click on the port or the printer you wish to connect to from the list.

4) Query the printer by using the Query Printer toolbar button (top-left) or the large ‘Query’ button in the green box. This will connect to the printer and get the current printer settings.

5) Click on the “Network” Tab, then click on

the Network Report button.

The Network Report will list the current

network settings of the printer, including the MAC and IP Addresses.

If DHCP is running on you network you may use the IP address displayed in the Network Report to:

> Install a printer driver, and start printing from your Windows applications; see Section B.3.

-or-

> Browse to the internal web pages for advanced configuration; see Section B.2

If you wish to assign a static IP Address continue to step 6.

44 Appendix B – Ethernet Setup

6) Click on the Wired Ethernet Configuration

button. First select the ‘Disabled’ radio button. Then enter valid values (within your network’s range) for the following fields:

- Printer IP Address

- Printer Subnet Mask

- Printer Gateway

7) Send the settings to the prin ter using the

Configure Printer toolbar button.

8) The printer will reset and will connect to

your network with the values you specified.

Once the previous steps have been successfully completed you may now use the IP Address to: > Install a printer driver, and start print ing fro m your W indow s app licat ions; see Sectio n B.3.

-or-

> Browse to the internal web pages for advanced configuration; see Section B.2.

Appendix B – Ethernet Setup 45

B

.

2

P

r

i

n

t

e

r

’

s

I

n

t

e

r

n

a

l

W

e

b

P

a

B

.

2

P

r

i

n

t

e

r

’

s

I

n

t

e

r

n

a

l

W

e

B

.

2

P

r

i

n

t

e

r

’

s

I

n

t

e

r

n

a

l

1. Open your web browser. Type in the IP Address of the printer. The Default IP is: 192.168.10.26.



Note: If you (or DHCP) have assigned a different IP address to the printer, make sure to

use this address.

2. The following page will appear:

W

e

b

g

P

a

g

P

a

g

e

s

The printer’s fourteen internal web pages are accessible via the navigation bar on the left-hand side. The Generic Network Configuration and Wired Ethernet Configuration pages contain many items

associated with the setup of the network card. The following tables provide information on each of the items listed on these pages.

 You must provide a password to change any settings; the default password is sysadm  After changes are sent to the printer (on all web pages), the printer must be reset in order for the



46 Appendix B – Ethernet Setup

changes to take effect. This can be done from the Reset Network Parameters web page.



If any address parameters were changed such as IP address, subnet or gateway, the printer might not be viewable from the current host if they are no longer on the same subnet.

Generic Network Configuration Page

NetBIOS (WINS) Settings

NetBIOS Name Is the name used to reference the printer instead of the IP address. A WINS or DNS

Primary WINS Server The IP address of the primary WINS Server. Secondary WINS Server The IP address of a secondary WINS Server.

TCP Print Services

TCP Port Number Selects the Port to use for all network communications; the default is 9100.

LPD Print Services

Enable/Disable LPD Print Services

SNMP Services

Enable/Disable SNMP Service

SNMP Server Address Is the Server address in standard octet format where SNMP traps will be sent when SNMP

SNMP Trap Address

Telnet Services

Enable/Disable Telnet Services

FTP Services

Enable/Disable FTP Services

HTTP (WWW) Services

Enable/Disable HTTP (WWW) Services

Netcenter Services

Enable/Disable Netcenter Services

Gratuitous ARP

Gratuitous ARP (Minutes) (Disabled=0)

server is required for this capability.

Enables the Line Printer Daemon (LPD) Service. Disables the Line Printer Daemon (LPD) Service

Allows management protocols, where:

Sends messages to SNMP-compliant devices. Sends no messages.

service is installed on your receiver. When zeroed, no traps are sent. Is the address in standard octet format where SNMP traps will be sent when SNMP

service is installed on your receiver. When zeroed, no traps are sent.

Allows Telnet protocol to transfer data, where:

Telnets to remote computers or server systems. Disables Telnet.

Allows FTP protocol to transfer data, where:

Enables FTP Disables FTP

Allows HTTP (WWW) protocol to transfer data, where:

Enables HTTP Disables HTTP

Allows Netcenter Services to transfer data, where:

Enables Netcenter Services Disables Netcenter Services

Sets time interval for ARP transmission packets, where: (0-2048 minutes); the default is Disabled.

Appendix B – Ethernet Setup 47

Wired Ethernet Configuration Page

DHCP

Controls IP Address discovery, where: Enabled: Broadcasts over the network to receive addresses from the responsible

server at startup. Manual modifications to IP Address, Subnet Mask, or Gateway are not allowed; and, if no server is found, the specified static value will be used.

Disabled: Uses the stored static IP, Subnet Mask, and / or Gateway Address.

Static IP Settings

Printer IP Address Printer Subnet Mask Printer Gateway

These are the static address the printer will use when DHCP is set to disabled or a valid IP could not be retrieved from a DHCP server.

Ethernet Port Connection Settings

Duplex Capability Allows the User to specify the line duplex and speed of the wired Ethernet connection.

Advertise Capability Selects the method in which the Duplex Capability setting is advertised, where:

Auto-Negotiate (default) 10 BaseT Full Duplex 100 BaseT Full Duplex 10 BaseT Half Duplex 100 BaseT Half Duplex

Automatic (advertises the selected Duplex Capability setting) All Capabilities (advertises all capabilities)

48 Appendix B – Ethernet Setup

B

.

3

I

n

s

t

a

l

i

n

g

t

h

e

P

r

i

n

t

e

r

D

r

B

.

3

I

n

s

t

a

l

i

n

g

t

h

e

P

r

i

n

t

B

.

3

I

n

s

t

a

l

i

n

g

t

h

e

P

Install the Printer Driver as follows (screen shots below are samples taken using Windows 2000; other versions will be similar):

1

Start the Windows Add Printer Wizard. The following screen should appear, and then click Next>.

3

Select Create a new port: and then select Standard TCP/IP Port from the drop down menu. Click Next>.

e

r

i

n

t

e

i

r

D

r

i

r

D

r

i

v

e

r

v

e

r

v

e

r

2

Make sure that Local Printer is selected and then click Next>.

4

Click Next>.

5

In the Printer Name or IP Address: field, enter the IP address of your printer. The Port Name field does not need to be changed. When finished click Next>.

7

Confirm your settings and then click Finish.

6

Make sure Standard is selected and then click Next>.

8

Click Have Disk

.

Appendix B – Ethernet Setup 49

9

Insert the Accessories CDROM and click Browse.

11

Click OK.

10

Browse to the \DRIVERS\ folder on the CD-ROM. Ensure the file “DatamaxO’Neil.inf” is selected then click OK.

12

Choose your printer from the list and then click Next>.

13

Assign a name in the Printer name field and select whether or not it is to be your default printer then click Next>.

15

Select No then Click Next>.

17

If prompted with the Digital Signature Not Found window, click Yes to continue installation.

14

Select whether or not to share this printer on your network. Then click Next>.

16

Confirm your settings and then click Finish.

18

Your computer will now copy the necessary files from the CD-ROM.

The driver and port installation is now complete. The printer can be selected through any Windows application.

50 Appendix B – Ethernet Setup

G

l

o

l

o

l

alphanumeric Consisting of alphabetic, numeric, punctuation and other symbols. backing material The silicon-coated paper carrier material to which labels with adhesive backing are

bar code A representation of alphanumeric information in a pattern of machine-readable marks. The

burn line The row of thermal elements in the printhead that create the images on the media. calibration The process through which sensor readings are entered into the printer for correct sensor

character set The entire complement of alphanumeric symbols contained in a given font. checksum An alphanumeric error detection method used in many bar code symbologies for

continuous media An uninterrupted roll or box of label or tag media that contains no gap, notch, or

core diameter The inside diameter measurement of the cardboard core at the center of a ribbon or

cutter A mechanical device with a rotary or guillotine type blade used to cut labels or tags following

defaults The functional setting values returned following a factory reset of the printer. diagnostics Programs used to locate and diagnose hardware problems. die-cut media Media that has been cut into a pattern using a press, where the excess paper is

direct thermal The printing method that uses heat sensitive media and the heat produced from the

direct thermal media Media coated with special chemicals that react and darken with the application

DPI (dots per inch) A measurement of print resolution, rated in the number of thermal elements

DPL Programming Language The programming commands used specifically for control of and label

fan-fold Media that is folded and stacked. feed speed The speed at which the media moves under the printhead in non-printed areas and

Flash memory Non-volatile memory (does not require printer power to maintain data) that can be

s

affixed. Also referred to as “liner”.

basic categories are divided into one-dimensional (UPC, Code 39, Postnet, etc.) and twodimensional barcodes (DataMatrix, MaxiCode, PDF417, etc.).

function (for example, detection of a given media type) and TOF positioning.

informational security.

mark to separate individual labels or tags.

media roll.

printing.

removed leaving individual labels, with gaps between them, attached to a backing material.

printhead to create an image on the label.

of heat.

contained in one inch of the printhead. Also referred to as “resolution”.

production with Datamax-O’Neil desktop printers. A complete listing can be found in the Class

Series 2 Programmer’s Manual.

between labels.

erased and reprogrammed, used to hold the printer’s operating programs.

a

r

y

r

a

s

o

Glossary 51

font A set of alphanumeric characters that share a particular typeface. gap A space between die-cut or notched labels used to sense the top of form. IPS (inches per second) Imperial measurement of printer speeds. label A paper or synthetic printing material, typically with a pressure sensitive adhesive backing. label length The distance from the top of the label to the bottom of the label as it exits the printer. label repeat The distance from the top of one label to the top of the next label. label tracking Excessive lateral (side to side) movement as media travels under the printhead. label width The left to right measurement of the label as it exits the printer. mark Generalized term to indicate the label top of form indicator of the media. media Generalized term for printing material. media hub Device in the printer used to support roll media.

media sensor An electronic device equipped with photo sensors to detect media and the top of form

on die-cut, notched or reflective media.

notched stock Media, typically tag stock, with holes or notches in the material that is used to signal

the top of form. The printer must be set to “gap” to use this media type.

preprinted media Label stock that contains borders, text, or graphics, flood coating, etc. perforation Small cuts extending through the backing and/or label material to facilitate their

separation. Also referred to as “perf”.

print speed The speed at which the media moves under the printhead during the printing process. reflective media Media imprinted with carbon-based black marks on the underside of the material,

which is used to signal the top of form when the reflective sensor is enabled.

registration Repeatable top to bottom alignment of printed labels. reverse speed The backward rate of media motion into the printer during tear-off, peel and present

and cutting operations for positioning the label at the start of print position.

ribbon An extruded polyester tape with several layers of material, one of which is ink-like, used to

produce an image on the label. Also referred to as “foil”.

ribbon wrinkle An undesirable overlapping of the ribbon during the printing process that leads to

voids on the printed label, typically caused by an improper ribbon width adjustment.

roll media A form of media that is wound upon a cardboard core. start of print The position on the label where the printing actually begins. tag stock A heavy paper or synthetic printing material, typically featuring a notch or black mark for

TOF and no adhesive backing.

thermal transfer The printing method that creates an image by transferring ink from a ribbon onto

the media using the heat produced from the printhead.

TOF (top of form) The start of a new label as indicated by a label gap, notch, mark or programming. void An undesirable blank space in a printed image.

52 Glossary

Datamax E-Class Mark II Operator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual