DX8200A-3002 QUICK GUIDE
DX8200A-3002
General View:
2
Laser Beam Output Windows
1
Mounting Slots
2
1
Figure A
3
4
Laser Safety Label
3
Mounting Reference Label
4
2
1
Programming Keypad
1
Power On LED (Green)
2
Phase On LED (Yellow)
3
Encoder LED (Yellow)
4
3
Figure B
4 5
2
5
6
7
6
TX Data LED (Green)
Network LED (Red)
LCD Display
7
1
2
Figure C
Lonworks 17-pin Male Connector
1
Lonworks 17-pin Female Connector
2
NOTE
For further details on product installation, see the complete Reference Manual available on the
configuration CD-ROM included with this product.
DX8200A-3002 QUICK GUIDE
Technical Features:
ELECTRICAL FEATURES
Supply voltage 20 to 30 Vdc
Power consumption 30 W typical
35 W Max. (including startup current)
Communication Interfaces
RS232 1200 to 115200
Lonworks 1.25 Mb/s
OPTICAL FEATURES
Light receiver Avalanche photodiode
Wavelength 630 to 680 nm
Safety class Class 2 - EN60825-1; Class II - CDRH
Light source Up to 4 semiconductor laser diodes
Laser control Security system to turn laser off in case of motor slow down
READING FEATURES
Scan rate
Maximum resolution
Max. reading distance
Max. reading width
Max. depth of field
USER INTERFACE
LCD Display 2 lines by 20 characters LCD
Keypad 3 keys
LED indicators Power On (green)
SOFTWARE FEATURES
Readable Codes
Code selection Up to 10 codes during one reading phase
Operating modes PackTrack™
Configuration modes Genius™ utility program
Parameter storage Non-volatile internal FLASH
Auxiliary Baud Rate
Other
≤ 1000 scans/s (500 per leg)
(see reading diagrams on page 9)
Phase On (yellow)
Encoder (yellow)
TX Data (green)
Network (red)
Interleaved 2/5
Code 39 Standard
Codabar
Code 128
EAN 128
Code 93 (standard and full ASCII)
EAN/UPC (including Add-on 2 and Add-on 5)
2
DX8200A-3002 QUICK GUIDE
ENVIRONMENTAL FEATURES
Operating temperature 0° to +50 °C (+32° to +122 °F)
Storage temperature -20° to +70 °C (-4° to +158 °F)
Humidity 90% non condensing
Ambient light immunity 20000 lux
Vibration resistance:
EN 60068-2-6
2 hours on each axis
Shock resistance:
IEC 68-2-27 test EA
3 shocks on each axis
Protection Class IP65*
PHYSICAL FEATURES
Mechanical dimensions
Weight
* IP65 cables and connectors required (CAB-850x or BTK-8500).
Constant displacement 3 mm pk-pk from 5 to 9 Hz;
Frequency range from 5 to 150 Hz;
Constant acceleration 0.5 g from 9 to 150 Hz;
30 g; 11 ms
470 x 300 x 141 mm (18.50 x 11.81 x 5.55 in)
about 11 kg (24 lbs 3 oz)
Accessories:
NAME Description Part Number
PWO-480 Power and Connect System 480W 93ACC1767
FS-1 Frame Shaper (8 pcs) 93ACC1750
S30 Photocell Kit 93ACC1782
MEP-542 Photocell Kit - PNP 93ACC1727
MEP-543 Photocell Kit - NPN 93ACC1728
OEK-2 Optical Encoder Kit + 10 m cable + Spring 93ACC1770
OEK-1 Optical Encoder Kit + 10 m cable 93ACC1600
BTK-8100 Bus Terminator Kit (5 pcs) 93ACC1090
BTK-8500 IP65 Terminator Kit (2 pcs) 93A051286
PLL-8000 Optocoupled PLL device 93ACC1280
CAB-8100 10 wire shielded cable D 9.5 mm – 50 m 93ACC1120
CAB-8101 17-pin scanner/scanner connection cable 1.2 m 93A051020
CAB-8102 17-pin scanner/scanner connection cable 2.5 m 93A051030
CAB-8105 17-pin scanner/scanner connection cable 5 m 93A051040
CAB-8501 IP65 Cable Fam 8K 1,2 m 93A051283
CAB-8502 IP65 Cable Fam 8K 2,5 m 93A051284
CAB-8505 IP65 Cable Fam 8K 5 m 93A051285
Sentinel-5 Supervisor (up to 5 arrays) 93A101004
Sentinel-10 Supervisor (up to 10 arrays) 93A101005
Sentinel-32 Supervisor (up to 32 arrays) 93A101007
3
DX8200A-3002 QUICK GUIDE
Electrical Connections:
Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output
connections to build a multi-sided or omni-station system.
17-pin Lonworks Connector Pinout
Pin Name
A1 GND Supply voltage (negative pin)
A2 VS Supply voltage 20 to 30 Vdc (positive pin)
1 CHASSIS
2 n.c. Not connected
3 CHASSIS
4 TXAUX
5 SGND Signal ground (connected to GND)
6 RXAUX
7 VS_I/O Supply voltage of I/O circuit
8 Lon A+ Lonworks a line (positive pin)
9 Lon A- Lonworks a line (negative pin)
10 Lon B+ Lonworks b line (positive pin)
11 Lon B- Lonworks b line (negative pin)
12 SYS_I/O System signal
13 SYS_ENC_I/O System signal
14 Reserved Internally connected
15 Ref_I/O Reference voltage of I/O circuit
Function
Cable shield A - internally connected by
capacitor to chassis
Cable shield B - internally connected by
capacitor to chassis
Transmit data of auxiliary RS232
(referred to SGND)
Receive data of auxiliary RS232
(referred to SGND)
1
A1
Male - Input
15
A1
1
Female - Output
17-pin Local Lonworks Connectors
A2
15
A2
4
Connectivity:
Host
HUB
DX8200A-3002 QUICK GUIDE
SC6000
DX8200A-3002
ETHERNET
CAB-850x
CAB-850x
DS8100A-3002
AUX
CAB-SC6003
Extended I/O
CAB-850x
DX8200A-3002
CAB-850x
up to 4
scanners per
branch
DS8100A-3002
CAB-SC6103
Cable
Power/Net
CAB-SC6003
LONWORKS
CAB-850x
up to 3
scanners
per
branch
VAC INPUT
PWO
ENCODER
BTK8500
Bus Return
DX8200A-3002
CAB-850x CAB-850x
DS8100A-3002
PS
PS Aux
DS8100A-3002
BTK8500
Bus Return
DX8200A-3002 Typical Layout
5
r
DX8200A-3002 QUICK GUIDE
to Host
ETHERNET
Working
Controller
SC6000
AUX
CAB-SC6003
Extended I/O
CAB-850x
CAB-850x
DX8200A DX8200A
CAB-SC6103
Power/Net
CAB-SC6003
LONWORKS
CAB-850X
DS8100A
Redundancy
CAB-PWO 03
VAC INPUT
CAB-850x
PWO
ENCODER
PS
PS Aux
BTK8500
DS8100A
to Host
ETHERNET
SC6000
Power/Net
CAB-SC6003
CAB-SC6003
Extended I/O
VAC INPUT
PWO
Protecting
Controlle
CAB-850x
LONWORKS
CAB-850x
CAB-850X
CAB-850x
ENCODER
PS
PS Aux
BTK8500
DX8200A DX8200A
DS8100A DS8100A
Example of Redundant System Layout
6
DX8200A-3002 QUICK GUIDE
Example of Redundant System
7
DX8200A-3002 QUICK GUIDE
Mechanical Installation:
DX8200A-3002 can be installed to operate in any position. There are 4 slots (dia. 8.5 mm) on the sides of the
scanner for mounting. The diagram below can be used for installation; refer to the Reading Diagrams for correct
positioning of the scanner with respect to the reading zone and scanner orientation.
470
= =
==
300
180
[7.09]
[11.81]
[18.50]
PackTrack™ Coordinate Reference Point
where x, y, z = 0
N° 4
8.5
[0.33]
22
[0.87]
10
[0.39]
406
[15.98]
370
[14.57]
370
[14.57]
22
[0.87]
==
147
[5.79]
==
DX8200A-3002 Overall Dimensions
Scanner Direction
The different scanner orientations are illustrated in the following figures:
Top View
Conveyor Direction
Conveyor Direction
60.5
70.5
Top View
[2.38]
141
[5.55]
[2.78]
DX8200A-3002 Scanner Direction 0° (Forward) DX8200A-3002 Scanner Direction 180° (Reverse)
8
DX8200A-3002 QUICK GUIDE
Reading Diagrams:
Note: x = 0 and z = 0 correspond to the edge of the DX8200A-3002 scanner as shown in the figure below.
DX8200A-3002 (0.50 mm/20 mils)
z
x
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Compliance:
Laser Safety
0
-15
0
-40
-28
-70
-24
-60
-20
-50
-16
-40
-12
-30
-8
-20
-4
-10
0
0
10
4
20
8
30
12
40
(in)
16
50
20
60
24
70
28
(cm)
-24
-60 -80
-32
-40
-100
-48
-56
-120 -140
-64
-160
(in)
(cm)
1
1
Figure A
Warning and Device Class Label
1
1
Figure B
Device Identification Label
The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser
product according to CDRH regulations.
Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to
hazardous laser light.
There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold
for its correct scanning speed.
9
DX8200A-3002 QUICK GUIDE
The laser beam can be switched off through a software command (see also the Genius™ Help On-Line).
LASER LIGHT
DO NOT STARE INT O BEAM
CLASS 2 LASER PRODUCT
MAXIMUM OUTPUT RADIATION 1 mW
EMITTED WAVELENGTH 630~680 nm
TO EN 60825-1:2001
CAUTION-CLASS 3B LASER LIGHT W HEN OPEN
AVOID EXPOSURE TO BEAM
LASER LIGHT EMITTED
FROM THIS
APERTURE
DATALOGIC S.P.A. Via Candini, 2
40012 Calderara di Reno - Bologna - Italy
Manufactured Volt
Model No. Amp.
Serial No.
This product conforms to the applicable requirements
of 21CFR1040 at the date of manufacture.
Device Identification Label
Warning and Device Class Label
The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1 regulations
and as Class IIIb laser products according to CDRH regulations. As it is not possible to apply a classification label
on the laser diodes used in this device, the following label is reproduced here:
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAXIMUM OUTPUT RADIAT ION 30 mW
EMITTED WAVELENGTH 630~680 nm
TO EN 60825-1 (2001)
Laser Diode Class Label
Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode
(30 mW at 630~680 nm).
Power Supply
This product is intended to be installed by Qualified Personnel only.
- This scanner is intended to be supplied by either a UL Listed power supply marked 'Class 2' or 'LPS', output
rated 20 - 30 V dc, minimum 1.75 A or by a UL Listed computer with LPS outputs.
- This scanner must be supplied by a Class II Power Supply Unit conforming to the EN 60950 safety
regulation.
WEEE Compliance
10
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DX8200A-XXXX
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
73/23/EEC Low Voltage Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit
entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas
de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 (C
MENDMENT A1 (CLASS A ITE), OCTOBER 2000:
A
EN 61000-6-2, O
EN 60950-1, D
EN 60825-1, J
MENDMENTS A11 (1996), A2 (2001)
A
, Laser Scanner
LASS A ITE),: AUGUST 1994
CTOBER 2001: ELECTROMAGNETIC COMPATIBILITY (EMC).
ECEMBER 2001: INFORMATION TECHNOLOGY EQUIPMENT - SAFETY –
UNE 1994:
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
L
IMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE
CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENTS
ART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS
P
P
ART 1: GENERAL REQUIREMENTS
S
AFETY OF LASER PRODUCTS –
ART 1: EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER’S GUIDE
P
05
EN 61000-3-2, D
EN 61000-3-3, J
ECEMBER 2000:
ULY 1995: ELECTROMAGNETIC COMPATIBILITY (EMC)
ELECTROMAGNETIC COMPATIBILITY (EMC)
PART 3-2: LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT
CURRENT UP TO AND INCLUDING
PART 3: LIMITS SECTION 3: LIMITATION OF VOLTAGE FLUCTUATIONS AND FLICKER IN
-VOLTAGE SUPPLY SYSTEMS FOR EQUIPMENT WITH RATED CURRENT <= 16A
LOW
ART 1: EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER'S GUIDE
P
16A PER PHASE)
Lippo di Calderara, 08/09/2005
Ruggero Cacioppo
Quality Assurance Laboratory Manager
821001251 (Rev. A)
Loading...