A
General View: Laser Safety:
12
1
11
DS4600A - 2XXX Models
2
4
10
DS4600A - 3XXX Models
Figure A
Cable with 25-pin Connector
1
Laser Beam Output Window
2
ccessory Mounting Holes
3
Warning Label
4
Mounting Holes
5
Data TX LED
6
External Trigger LED
7
8
Good Read LED
Ready LED
9
Warning and Classification Labels
10
Keypad
11
Display
12
For further details on product installation, see the
complete Installation Manual available on the WinHost
CD included with this product.
Power Supply:
- This product is intended to be installed by Qualified
Personnel only.
- Models DS4600A-XXX0:
This device is intended to be supplied by a UL Listed
Direct Plug-in Power Unit marked “Class 2”, rated 10-30
V minimum, 0.60 A.
This device may also be supplied by a UL Listed Power
Unit marked “Class 2” or LPS power source which
supplies power directly to the scanner via the 25-pin
connector.
- Model DS4600A-2XX5:
This device is intended to be supplied by a UL Listed
Direct Plug-in Power Unit marked “Class 2”, rated 24 V
minimum, 0.50 A.
This device may also be supplied by a UL Listed Power
Unit marked “Class 2” or LPS power source which
supplies power directly to the scanner via the 25-pin
connector.
WEEE Compliance:
The scanner is classified as a Class 2 laser
product according to EN 60825-1 regulations
and as a Class II laser product according to
CDRH regulations.
For installation, use and maintenance it is not
necessary to open the device.
There is a safety device which allows the
laser to be switched on only if the motor is
rotating above the threshold for its correct
3
scanning speed.
The laser beam can be switched off through a
software command (see also the WinHost
Help On-Line).
AVOID EXPOSURE
LASER LIGHT IS EMITTED
FROM THIS APERTURE
CAUTION-CLASS 3B
LASER LIGHT
2
WHEN OPEN
AVOID
EXPOSURE TO BEAM
DATALOGIC S.p.A. Via Candini, 2
40012 LIPPO DI CALDERARA (BO) ITALY
Model No. Serial No.
Volt Amp.
Manufactured
This product conforms to the applicable requirements of
21CFR1040 at the date of manufacture.
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAXIMUM OUTPUT RADIATION 1 mW
EMITTED WAVE LENGTH 630~680 nm
Warning and device class labels
The laser diode used in this device is classified
as a class 3B laser product according to EN
60825-1 regulations and as a Class IIIb laser
product according to CDRH regulations. As it is
not possible to apply a classification label on
the laser diode used in this device, the
following label is reproduced below.
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAX. OUTPUT RADIATION 30 mW
EMITTED WAVE LENGTH 630~680 nm
Laser diode class label
Any violation of the optic parts in particular
can cause radiation up to the maximum level
of the laser diode (30 mW at 630 to 680 nm).
DS4600A QUICK GUIDE
LASER LIGHT
TO EN 60825-1 (2001)
LASER LIGHT
TO EN 60825-1 (2001)
2
V
Model Description:
DS4600A QUICK GUIDE
DS4600A - X X X X
Decoding Mode
= Standard w/ Display
3 = Advanced Code Reconstruction
Reading Range
0 = Medium Range
1 = Long Range
2 = Short Range
Optic
ersion
0 = Linear
1 = Raster R1
2 = Raster R2
Special Features
0 = Standard
5 = Integrated Heater
The following table displays each version’s reading performance.
Version Reading Distance
Max Code Resolution
mm (mils)
210X 200 mm (8 in) - 980 mm (39 in) on 1.00 mm (40 mils) codes 0.50 (20) 800
200X 160 mm (6 in) - 540 mm (21 in) on 0.50 mm (20 mils) codes 0.25 (10) 800
220X 50 mm (1.97 in) - 400 mm (15.75 in) on 0.80 mm (31 mils) codes 0.20 (8) 800
310X 200 mm (8 in) - 970 mm (38 in) on 1.00 mm (40 mils) codes 0.50 (20) 800
300X 160 mm (6 in) - 540 mm (21 in) on 0.50 mm (20 mils) codes 0.25 (10) 800
320X 120 mm (4.7 in) - 310 mm (12.2 in) on 0.30 mm (12 mils) codes 0.20 (8) 800
Technical Features:
ELECTRICAL FEATURES SOFTWARE FEATURES
Power Supply
Model XXX0: 10 –30 Vdc
Model 2XX5: 24 Vdc
Power Consumption
max.
Main Serial Interface
Model XXX0: 6W
Model 2XX5: 12W
RS232;
RS485 Full-Duplex
RS485 Half-Duplex
Auxiliary Interface
Baudrates
Inputs
External Trigger, IN1,
RS232
1200 to 115200
(optocoupled NPN or PNP)
IN2
Voltage max.
Current Consumption
max.
Outputs
OUT1, OUT2
V
max.
CE
Collector Current
max.
VCE Saturation
Power Dissipation
max.
30 Vdc
25 mA
(optocoupled OE or OC)
40 Vdc
40 mA continuous;
130 mA pulsed
1V at 10 mA max.
90 mW at 40 °C
(Ambient temp.)
OPTICAL FEATURES Temperature
Light Source
Wavelength
Safety Class
Semiconductor laser diode
630 to 680 nm
Class 2 - EN 60825-1; CDRH
USER INTERFACE Vibration Resistance
LED Indicators
Ready, Good Read, IEC 68-2-6 test FC 1.5 mm @ 13 to 55 Hz
External Trigger,
Data TX
PHYSICAL FEATURES Shock Resistance
Dimensions
Weight
101x84x42 mm
(22 oz)
615 g.
(4x3.3x1.7 in) IEC 68-2-27 test EA 3 shocks on each axis
Readable Codes
EAN/UPC (including Add-on 2
and Add-on 5)
Code 39
2/5 Interleaved
Code 128
EAN 128
Code 93
Codabar
Headers and
Terminators
Operating Modes
Configuration Modes
Pharmacode
Up to four header and four
terminator characters
On-Line, Automatic,
Serial-On-Line, Test
Through menus using
WinHost utility
Host Mode (commands from
Code Selection
Parameter Storage
one of the serial ports)
Up to six different codes
during one reading phase
Non-volatile internal
EEPROM
ENVIRONMENTAL FEATURES
Operating
0° to 40 °C (32° to 104 °F)
2XX5: -30° (-22 °F) to 40 °C
Storage
Temperature
Humidity max
-20° to 70 °C (-4° to 158 °F)
90% non condensing
14 mm @ 2 to 10 Hz
2 g @ 70 to 200 Hz
2 hours on each axis
30g; 11 ms;
Protection Class
IP65
Speed
scans/s
2
DS4600A QUICK GUIDE
Accessories:
Name Description Part Number
C-BOX 100/200 Connection Box 93ACC1510, 93ACC1520
C-BOX 300/310 Connection Box Profibus 93A301000, 93A301030
C-BOX 400/410 Connection Box DeviceNet 93A301010, 93A301040
GFC-41 90° Reading Device 91D081000
OM4000 Oscillating Mirror 93A251030
INT-30 (for C-Box 100) 20 mA Current Loop Interface Board 93A151022
Electrical Connections:
DS4600A is equipped with a cable terminated by a 25-pin female D-sub connector for connection to the power
supply and input/output signals.
Do not connect GND and SGNDs (Main or Aux) to different (external) ground references.
GND and SGNDs (Main and Aux) are internally connected through filtering circuitry which
CAUTION
The details of the connector pins are indicated in the following table:
can be permanently damaged if subjected to voltage drops over 0.8 Vdc.
25-pin D-sub female connector pinout
Pin Name Function
13 VS Power supply input voltage +
25 GND Power supply input voltage -
1 CHASSIS Chassis Ground
9 VS External Trigger supply voltage +
18 EXT TRIG+ External Trigger +
19 EXT TRIG- External Trigger -
6 IN1+ Input 1 +
10 IN1- Input 1 14 IN2+ Input 2 +
15 IN2- Input 2 -
8 OUT1 + Output 1 +
22 OUT1- Output 1 11 OUT2 + Output 2 +
12 OUT2- Output 2 20 RXAUX Auxiliary RS232
21 TXAUX Auxiliary RS232
23 SGND Aux Signal Ground Auxiliary interface
24 GND Power Supply Voltage 16 Reserved
17 Reserved
Pin RS232
2 TX232 TX485+ RTX485+
3 RX232 RX485+
4 RTS232 TX485- RTX485-
5 CTS232 RX485-
7 SGND Main SGND Main SGND Main
RS485
Full-Duplex
25-pin female connector
RS485
Half-Duplex
3
Mechanical Installation:
DS4600A QUICK GUIDE
22*
0.86
41.8
10
0.39
1.64
81
3.19
M4 N° 4
0.46
11.8
37
5
1.47
0.2
0.32
8.25
87.9
3.46
Mounting hole depth M4 X 5
20.2
0.8
37
1.46
42
1.65
* The quote refers to the scan line
Overall dimensions for 2XXX Models
Input/Output Connections:
DS4600A 25-pin
8/11
C
12/22
E
Output open collector connections
V
max = 40 Vdc
CE
I max = 40 mA continuous
DS4600A 25-pin
+ 5V
Open Collector
+
-
Vext 30 Vdc max.
18/6/14
19/10/15
+
-
USER INTERFACE
NPN NPN
USER INTERFACE
20
2.28
1.28
0.79
1.55
39.4
101
3.98
18
0.70
14.8
0.58
M4 N°2
58
32.5
3.75
0.15
Vext 40 Vdc max.
V
Signal
0.90
18*
0.71
20.2
83.5
3.29
37
1.46
DS4600A
23
14.8
0.58
0.8
42
1.65
* The quote refers to the scan line
M4 N°2
58
2.28
1.28
32.5
3.75
0.15
20
0.79
83.5
3.29
1.55
39.4
101
3.98
18
0.70
23
0.90
Overall dimensions for 3XXX Models
5.5
0.22
115
4.53
5
0
.
57.3
2.26
.
5
2
2
5
.
5
2
2
.
0
35°
1
0
°
5
0.20
5.5
0.22
39
1.54
3
0.12
Mounting Bracket Dimensions
DS4600A 25-pin
+ 5V
9
18/6/14
19/10/15
25
USER INTERFACE
VS
+
-
GND
V
Ground
Signal
DS4600A 25-pin
+ 5V
4
Input NPN command using external power
PNP
PNP
Vext 30 Vdc max.
18/6/14
19/10/15
+
-
Input PNP command using external power
USER INTERFACE
V
Ground
Signal
Input NPN command using DS4600A power
VS
+
-
GND
USER INTERFACE
V
Ground
DS4600A 25-pin
+ 5V
9
18/6/14
19/10/15
25
Input PNP command using DS4600A power
Signal
Connectivity:
Point-to-point layout
DS4600A QUICK GUIDE
c Main Serial Interface
dAuxiliary Serial Interface (Local Echo) (RS232)
eExternal Trigger (for On-Line Mode)
Pass-through layout Multiplexer layout
c Main Serial Interface (RS232) c Main Serial Interface (RS485 Half-Duplex)
dAuxiliary Serial Interface (RS232) dAuxiliary Serial Interface (Local Echo) (RS232)
eExternal Trigger (for On-Line Mode) eExternal Trigger (for On-Line Mode)
RS232 Master/slave layout RS485 Master/slave layout
c Main Serial Interface (Slaves RS232 only) c Auxiliary Serial Interface (RS232)
dAuxiliary Serial Interface (RS232) d Main Serial Interface (RS485 Half-Duplex)
eExternal Trigger (for On-Line Mode) eExternal Trigger
5
Reading Diagrams:
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Resolution:
Standard - for 0.50 mm (20 mils) codes
and greater
*Code Reading Condition:
Standard
* Parameter selectable in WinHost.
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 15°
Tilt angle = 0°
*Code Resolution:
High - for 0.30 mm (12 mils) codes and
smaller
Standard - for 0.50 mm (20 mils) codes
and greater
*Code Reading Condition:
Standard
* Parameter selectable in WinHost.
DS4600A-210X (Long Range)
16
12
-4
-8
-12
-16
(in)
400
300
8
200
4
100
0
-100
-200
-300
-400
(mm)
04 2012
0
816
100 200 300 400 500 600 700 800 900 1000
DS4600A-200X (Medium Range)
10
-2
-4
-6
-8
02 6412
0 50
250
200
8
6
150
100
4
50
2
0
0
-50
-100
-150
-200
100
150 200 250 300 350 400 450 500 550
DS4600A QUICK GUIDE
24 28 32 36 40
0.50 mm
0.60 mm
0.80 mm
1.00 mm
8 10 14 16 18
0.25 mm
(10 mils)
(20 mils)
(24 mils)
(31 mils)
(40 mils)
0.30 mm
(12 mils)
20 22
0.50 mm
(20 mils)
(in)
(mm)
(in)
(mm)
6
-10
(in)
-250
(mm)
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 10°
"Tilt" angle = 0°
*SW Resolution = High
* Parameter selectable in WinHost
DS4600A-22XX (Short Range)
01 3210 6
0
20
40 60
5
120
100
4
80
3
60
2
40
1
20
0
0
-20
-1
-40
-2
-60
-3
-80
DS4600A QUICK GUIDE
45 7 8 9
80
100 120
140
160
0.20 mm
(8 mils)
180
200
220
0.30 mm
(12 mils)
240
260
11
280
(in)
(mm)
CONDITIONS
Test Codes used = Interleaved 2/5 and
Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 10°
"Tilt" angle = 0°
*SW Resolution = Low
* Parameter selectable in WinHost
-100
-4
-120
-5
(mm)
(in)
DS4600A-22XX (Short Range)
02 64 20 12
0
40
10
8
6
4
2
0
-2
-4
-6
80 120
240
200
160
120
80
40
0
-40
-80
-120
-160
160
8 10 14 16 18
200 240
280 320
360
400
440
0.50 mm
(20 mils)
0.60 mm
(24 mils)
≥ 0.80 mm
(31 mils)
480
520
(in)
(mm)
-200
-8
-240
-10
(mm)
(in)
7
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 18°
"Tilt" angle = 0°
*Code Resolution:
High - for 0.30 mm (12 mils) codes and
smaller
Standard - for 0.50 mm (20 mils) codes
and greater
*Code Reading Condition:
Standard
* Parameter selectable in WinHost.
DS4600A-2X1X (Raster R1)
10
0
-2
-4
-6
-8
02 6412
0 50
250
200
8
150
6
100
4
50
2
0
-50
-100
-150
-200
DS4600A QUICK GUIDE
810 1416 18
100
150 200 250 300 350 400 450 500 550
0.30 mm
(12 mils)
0.25 mm
(10 mils)
20 22
0.50 mm
(20 mils)
(in)
(mm)
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
Pitch angle = 0°
Skew angle = 18°
Tilt angle = 0°
*Code Resolution:
High - for 0.30 mm (12 mils) codes and
smaller
Standard - for 0.50 mm (20 mils) codes
and greater
*Code Reading Condition:
Standard
* Parameter selectable in WinHost.
-10
-250
(mm)
(in)
DS4600A-2X2X (Raster R2)
10
0
-2
-4
-6
-8
02 6412
0 50
250
200
8
6
150
100
4
50
2
0
-50
-100
-150
-200
100
150 200 250 300 350 400 450 500 550
810 1416 18
0.30 mm
(12 mils)
0.25 mm
(10 mils)
20 22
0.50 mm
(20 mils)
(in)
(mm)
8
-10
(in)
-250
(mm)
CONDITIONS
Code = Interleaved 2/5 and Code 39
"Pitch" angle = 0°
"Skew" angle = 15°
"Tilt" angle = 0°
*Code Resolution =
Standard for 0.50 mm (20 mils) codes
and greater
*Code Reading Conditions = Standard
* Parameter selectable in WinHost
CONDITIONS
Code = Interleaved 2/5 and Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 15°
"Tilt" angle = 0°
*Code Resolution:
High for 0.30 mm (12 mils) codes and
smaller
Standard for 0.50 mm (20 mils) codes
and greater
*Code Reading Conditions: Standard
* Parameter selectable in WinHost.
DS4600A-31XX (Long Range)
16
12
8
4
-4
-8
-12
-16
(in)
04 2012
0
400
300
200
100
0
-100
-200
-300
-400
(mm)
816
100 200 300 400 500 600 700 800 900 1000
DS4600A-30XX (Medium Range)
10
8
6
4
2
0
-2
-4
-6
02 6412
0 50
100
150 200 250 300 350 400 450 500 550
250
200
150
100
50
0
-50
-100
-150
DS4600A QUICK GUIDE
24 28 32 36 40
0.50 mm (20 mils)
0.60 mm (24 mils)
0.80 mm (31 mils)
1.00 mm (40 mils)
8 10 14 16 18
0.30 mm
(12 mils)
0.25 mm
(10 mils)
20 22
0.50 mm
(20 mils)
(in)
(mm)
(in)
(mm)
-8
-200
-10
-250
(mm)
(in)
9
DS4600A QUICK GUIDE
DS4600A-32XX (Short Range)
02 64 20 12
0
40
10
240
80 120
8 10 14 16 18
160
200 240
280 320
360
400
440
480
520
(in)
(mm)
CONDITIONS
Code = Interleaved 2/5 and Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 15°
"Tilt" angle = 0°
*SW Resolution: High
* Parameter selectable in WinHost.
8
6
4
2
0
-2
-4
-6
-8
-10
(in)
200
160
120
80
40
-40
-80
-120
-160
-200
-240
(mm)
0.20 mm
(8 mils)
0.25 mm
(10 mils)
≥
0.30 mm
0
(12 mils)
10
User Interface:
DS4600A QUICK GUIDE
RS232 PC-side connections
1
1
5
13
9 6
9-pin male connector
25-pin male connector
25 14
Pin Name Pin Name
2 RX 3 RX
3 TX 2 TX
5 GND 7 GND
7 RTS 4 RTS
8 CTS 5 CTS
How To Build A Simple Interface Test Cable:
The following wiring diagram shows a simple test cable including power, external (push-button) trigger and PC
RS232 COM port connections.
DS4600A
25-pin D-sub male
TXAUX
21
20
RXAUX
SGND
23
13
VS
25
GND
9
VS
18
EXT TRIG+
19
EXT TRIG-
9-pin D-sub female
Power Supply
VS (10 – 30 Vdc)
Power GND
2
RX
PC
3
TX
5
GND
Trigger
Test Cable for DS4600A
11
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
05
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DS4600A-XXXX Laser Scanner e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
der nachstehend angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit
entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas
de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 (C
MENDMENT A1 (CLASS A ITE), OCTOBER 2000:
A
EN 61000-6-2, O
LASS A ITE), AUGUST 1994:
CTOBER 2001: ELECTROMAGNETIC COMPATIBILITY (EMC).
L
IMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE
CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT
ART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS
P
(ITE)
Lippo di Calderara, 08/09/2005
Ruggero Cacioppo
Quality Assurance Laboratory Manager
821000693 (Rev. D)
Loading...